Issue of Sony STR - DN1040 output HDMI Samsung UN60F8000BFXZA TV

Hello community of Sony,

I have a question of a Samsung UN60F8000BFXZA TV HDMI Sony STR-DN1040 output.  I have a cable Xfinity RNG110 box and a Samsung Blue Ray BD-F5900 connected via HDMI 1.4 cables I have HDMI 1.4 cables connecting all devices.  I had the GeekSquad install TV and set up the Sony A / V receiver.  Everththing was working fine.  I turned off the system for a few hours and came back and turned on everything.  Initial configuration is A / V HDMI's out to TV input HDMI3.  HDMI input and output supports CRA.  The TV would constantly check your connection to the device.  No video just a black screen.  Power cycle sometimes or reinstall the cables could clarify the issue.  Same problem you select, the cable box or the player blue ray, as input device...  I swapped the HDMI cable from the upper area of the rec AV cable and the cable to the AV rec on television.  No change in symptoms.  I even hooked up the TV to the AV HDMI B outupt with no change in symptoms.  I directly connect the cable box to TV without problems.  I get video every time.  I'm afraid I see many messages from simular 'video problem' on the receiver AV STR-DN1040.  The two TV and AV receiver have been purchased this week.  What should be the next steps?  I have the Geek Squad back to verify that I may have a problem of AV receiver.

Cheers, Oakleyrider


Tags: Sony Products

Similar Questions

  • Sony STR-DN1040 receiver help

    I have a Sony STR-DN1040 receiver. I have my PC connected to the receiver and I can not get sound when I have an optical cable connected to my receiver. I have the cable plugged into OPT1 and cable HDMI plugged into Video 1 (note: my PC sends no audio through the HDMI, so I have to use the optical audio input). I got this Setup on my previous Onkyo receiver and everything worked perfectly. I have not changed the PC settings so everything on this end should always be configured correctly. Any help would be appreciated.

    Thank you

    Andy

    You can reassign the DIGITAL to other entries input jacks, if the default settings of the sockets do not match your own equipment.  The default assignment of OPT1 (where you plugged in your PC) is SAT/CATV and which could be the reason why there is no audio coming out of your receiver, even if the PC is out the digital signal.

    Try to set OPT1 to VIDEO1 under [A. ASSIGN] assignment of digital audio menu. Follow the steps below

    1 press AMP MENU

    The menu is displayed on the notice board of the receiver.

    2 go all the way to Input settings]]

    3 select digital audio input assignment [A. ASSIGN]

    4 the value OPT1 VIDEO 1

    See page 86 to 87 of the manual provided for more information on the assignable audio input jacks.

    If this post answers your question, click on "accept as a Solution.

  • Remote control Medai vs STR-DN1040 cannot change the source?

    I just installed my Sony STR-DN1040 home theater receiver and have a few questions about the media remote ap...

    (1) I have it all connected and registered and the ap is functional, but in "remote mode", it lists all entries in my (BD, cable/satellite, DVD, FM, etc) as buttons, I can support on and they light up and make a tone of confirmation on my iPhone 4s, but they do not change the source to the receiver.  The rest of the features seem to work and if I use the media remote ap for go to the GUI menu, I can arrow over 'look' and then select a source, and that works fine.  The problem is when you are in another room and want to power on the receiver, then choose an audio source and play without having to turn on the TV or be in this room, you can't (or at least I can't) because the hot-key source on the ap do nothing.  What did I miss?

    (2) I have programeed the 1040's physical remote to control my Samsung Blu - Ray player.  The Medai remote access point can now also control it, or is the 1040's remote physical a completely separate device?

    Thank you!

    Hello Apcrews,

    The STRDN1040 was intended to be used with the Sony 'TV Sideview demand' which includes many new features and replace the existing approx. remote media TV Sideview will will allow you to switch between inputs, however there is no visual feedback in the app, so you'll need visibility on the front panel of the receiver or GUI.

    The application will not work to control your player of Samsung BD. The reason is that you have programmed the 1040's physical remote to control the player of comic book via codes IR (infrared), these codes resident in actual distance rather than the receiver and the orders are sent directly from the 1040's remote control.

  • My STR-DN1040 will not power "on".

    Yesterday, I bought a brand new Sony STR-DN1040 at Best Buy.  I came home and hung it through Monster THX HDMI for my Sony KDL-52XBR9 HDTV cables, my reader blu - ray Sony BDP-BX57, 52 '' my box of cable Motorola DCX3510-M and my Polk Audio 7.1 surround subwoofer and satellite speaker system.  I have connected the STR-DN1040 via ethernet to a cable modem, which is located in the same rack as the home theater unit. Everything was (is) connected properly.

    I plugged the STR-DN1040 in my Monster surge protector/power strip behind the shelf of home theater. where all other components are connected.  I heard the slight, familiar "click" can be received and activated inside the STR-DN1040.

    I turned on my TV box and cable.  I went to the front of the STR-DN1040 "in office", but the small LED above the power button was already green, as if he (power) on its own.  So, I waited.  And waited and waited... something appears on the STR-DN1040 screen, but nothing ever presented.  I thought that perhaps he made an update of the firmware straight out of the box, but after an hour, it became apparent that something was wrong.  Then...

    I unplugged the STR-DN1040 and let stand for 30 minutes.  I plugged it in and it did the same thing as described above.  The Green LED power 'works' light comes on in a few seconds the power cable is plugged in, unless you press the power button on the front of the unit.  And then... He's just sitting there.  The device does not react to any pressure on the buttons or dials on the front.  The device does not respond to a key pressed on the remote control.  I checked all HDMI connections and even changed the HDMI cables, but I get nothing. Unit seems dead - D.O.A. The green light is 'on' on the front, but that's all.

    Anyone have any ideas what might this happen? Everyone heard about this problem or has experienced this themselves?  Have I not a dud?  Should I just return it and get another?

    I went through this process.  It seemed to work.  Leave the House and came after a few hours and I'm back to the same problem.  Tried to "clear" it, but that never happens.  I held the button for 5 then 10, then 15. No COMPENSATION.  I'm ready to ship in return!

  • Roku on STR-DN1040

    entry saWhich will give me the best performance for a Roku player?  I tried the SA-CD, but it doesn't seem to work so I went into the entry DVD.  Is there a better option?

    Hello.

    You can connect the Roku Streaming Player at the Sony STR - DN1040 AV receiver using HDMI connection to one of the HDMI Ports IN front of the receiver (for example, DVD or VIDEO), and then press the corresponding button on the receiver's remote control to set the camera to the correct input.

    If my post answered your question, please click "accept as a Solution.

  • STR DN1040 HDMI HDCP issues

    I have a recurring issue with my new receiver STR-DN1040. It works fine for a while and then it stops negotiating devices on my TV HDCP. For example, my PS3 will display a black screen when I turn it on. My TiVo Series 3 displays a screen saying that there is a negotiating HDCP error trying to watch cable channels. The only solution I found is to unplug the receiver from the wall and plug it in again - then it immediately starts working again.

    It produces at least a couple of times a week, and it's extremely frustrating. Looking at a few discussions on here and other websites this is not an uncommon problem.

    I tried tweaking about all the settings that I can think of nothing doesn't. One who seems to have made the most difference is turning off the fast display of the HDMI, but it might just be a coincidence.

    Here's what I connected through my receiver (all with HDMI):

    Apple TV

    Xbox 360

    Wii U

    PlayStation 3

    TiVo Series 3

    Sony BDP-S360 Blu Ray

    My TV is a Sony KDL-46EX710.

    My HDMI outputs receiver / A + B the TV (I have a set of HDMI input upwards for games and one for the TV-movie).

    As you can tell, I love my Sony AV products. I wish just that this receiver has worked reliably for me.

    Is this a known problem and it's something that will be fixed in a future update? I really want to love this receiver (and most of the time I do - when it works!), but every time I turn on the TV and get a HDCP error, I want to throw it out the window.

    Ideas or ideas here would be appreciated.

    Thank you!

    High-bandwidth Digital Content Protection (HDCP) is a system of protection against copying in order to eliminate the ability to capture digital content from the source to the screen. It is designed to protect digital signals when using a DVI Interface (Digital Video) and High-Definition Multimedia Interface (HDMI).

  • Output HDMI not working not not for Dell XPS L502X does not work after upgrade to Windows 10

    Hi all

    Good so I have this laptop Dell XPS L502X that I bought in 2012. The laptop provided with Microsoft Windows 7 Home Edition.

    His output HDMI for my Sony LED used previously to work properly.

    But there are a few months that those offered by Microsoft, I upgraded my OS from Windows 7 Home edition to Windows Home Edition 10 laptop.  Since the upgrade, everything worked fine except I don't get HDMI output to my TV.

    I tried to search for solutions online but do not know what could be the problem? Can someone guide me in the right direction please?

    Thank you.

    I am happy to update this thread, the problem of my laptop screen is displayed using HDMI on my Sony TV, solved on its own with the last update for Windows 10 which includes the OS 1607 version build: 14393.187

    To all of you who always fights for the configuration of HDMI output for their laptop to the television after upgrade to Windows 10, I'm sure that the last Windows Update will solve the problem.

  • Lenovo N500 no output HDMI port

    I have Lenovo N500 42334 CG which provided nice output HDMI connected via a cable HDMI for TV LCD today, I tried to log in again, but unfortunately there is no video / audio on television the HDMI Lenovo, tried changing the HDMI sockets on my TV without success. BIOS reported by Lenovo diganostics is 6GET19ww (for the non-HDMI), even an inappropriated BIOS update has been installed on my Lenovo such that does not support HDMI output port more? Any other problem maybe? How to resolve? Thank you

    problem solved, apparently bios was WITHOUT HDMI, so go back to the previous bios resolved the issue. This message can be closed.

  • A difference card STR-DN1040 US / UK

    Hi, I got a little curious earlier today, when I went in the store to buy my new A / V Amp and I was told that there was no Bluetooth.

    Well, I had seen Youtube and also the same site that the STR-DN1040 has Bluetooth, WIFI, and Airplay, so I was quite insistent that this was the case.  I was of course wrong, because I am in the United Kingdom and for one reason or another its been subscribed.

    http://www.sony.co.uk/product/hcs-home-cinema-receiver/str-dn1040 - this is the version that we get.

    So the question I would ask is, while I'm more to the United States in one of the next weeks I can pick it up and bring it back to the UK?  What (if any) problems will I have?

    My intention is to use in conjunction with the BRAVIA TV KDL46W905A, the functions will work as they normally would?

    All other points to note would be greatly apreciated IE too... is the international warranty ETC.

    Thank you

    Dave

    Receiver AV multichannel STR-DN1040 which is sold to the United States, Canada, Mexico & Brazil has a Bluetooth device built for music streaming from your smartphone or tablet. It has also built-in Wi - Fi and AirPlay, while the STR-DN1040 sold in the UK is not compatible Bluetooth.

    Outside the Bluetooth function, the main difference between the American and British models are the power requirements and the tuner AM beach. The audio/video receiver to the UK has power supply 230 v AC , 50/60 Hz while the unit in the U.S. requires 120 V AC, 60 Hz. Please see pages 6 to 8 of the Manual for model UK (this is optimized by using the Internet Explorer browser) and pages 127-130 of the Manual WE for more information. We cannot recommend any power converter.

    Normal warranty terms apply. The American unit has 730 days warranty for labor and parts. If ever the unit require warranty service, you have the option to send your unit to the Sony Repair Service Center in the United States for warranty repairs. You will be responsible for met shipping charges to ship the unit to the repair center. Your device will be returned to you free of charge. You will be responsible for all rights, taxes or fees. Or, you can have the device repaired in the country where you are, to normal pricing of warranty repair.

    If my post answered your question, please click "Accept as a Solution."

  • Add Wireless for SONY STR-DG510 receiver speakers

    I have a SONY STR-DG510 receiver. It has 3 speakers (right, left & Center) connected now.

    I would like to add two speakers more to it. The outputs are available on the receiver, but I don't

    not like the idea of the wires running in all directions.

    I thought using a wireless speaker I could at least eliminate the wires of the receiver.

    Any suggestions on what to use? Most of the things I find is oriented towards computers or cell

    Phones.

    Thanks for your suggestions

    RS

    I thought that this kind of, but hoped someone could tell me

    something that will work.

    RS

  • Why the STR-DN1040 update taking so long?

    Today, my new STR-DN1040 has received an update that you download the package and held in Updating, flashing on the screen because some then only green light flashing update then just green pwr/standby blinking light.

    In short Question why must Sony A / V Receiver so long to update since nearly an hour

    (Update: it finally all 2 hours later, but something weird happen the name of the network device changed some thing I don't set and was not default)

    The update download speed depends on your internet connection. If you have internet high speed (i.e. the download speed of 10 Mbps or higher according to the website www.2wire.com ) and is only used by the AV receiver then it may not take as long.

    What is the new name under the option network device? It's a normal operation that can change after the software update, so it can easily be seen when configuring the network connection.

    If my post answered your question, please mark it as "accept as a Solution.

  • Portege M800-105 - output HDMI for XP driver?

    Hello

    I have a question that belongs to the HDMI output.
    I put Windows XP Home on my Portege with all the driver from Toshiba support page but my HDMI output does not work.

    Now, I saw that there is a driver for Vista called output HDMI Toshiba.
    Anyone know a driver called like this for Windows XP?
    Or does anyone have the same problem with XP but the HDMI does not work?

    I hope someone can help me with this problem.

    THX

    dschumacher

    Hello

    As much as I know, that he is a driver Intel High Definition Audio HDMI.
    I m not a M800 owner but I ve got a Satellite U400 with HDMI output and installed XP.

    To be honest I didn t notice any yellow exclamation in my device manager but I installed the page Intel's Intel High Definition Audio HDMI driver
    http://www.Intel.com/support/chipsets/sb/CS-009244.htm

    Maybe this site will help you

    But note; Some features of the laptop not available in Win XP, but only under Vista!

  • How to get my dv7 Pavilion to show the OUTPUT HDMI option in reading?

    HP Pavilion dv7 - 1157cl Entertainment Notebook PC

    FS155UA #ABA

    Windows 7 Professional

    By other suggestions:

    * Uninstalled all drivers graphics & audio drivers

    * Installed later, now have:

    Mobile Intel 4 Series Express (8.15.10.2555)

    IDT High Def Audio CODEC (6.10.6207.0)

    Intel High Definition Audio HDMI (6.10.1.2089)

    * Impossible to correctly Reinstall driver nvidia geforce 9200 m gs or AMD driver graphics high definition

    Output HDMI does not appear as an option in audio playback (pilot reports: "this device works properly.")

    Is the reason for which the graphics card driver missing?

    Which will solve this problem so that I can choose an HDMI output?

    Thank you!

    And the answer is: I had installed the latest drivers (and thanks to response above realize did not need graphics driver, although the HP site indicated as well), BUT the HDMI audio driver does not appear until I plugged in the TV, duh... I was not expecting to see the disconnected HDMI option  Once I have connected to the TV, it seemed. Subsequently, it does not show as a disconnected option.

    Lesson learned: after reinstallig, connect to the TV.

    Thanks for the help.

  • Sound of television through Sony STR-DH130 receiver

    I recently bought a receiver SONY STR-DH130.  As with my previous receiver (an old Kenwood 3090) I have connected it to the top so that the sound of my SONY's Trinitron TV through the receiver to separate the speakers.  However, unlike with my Kenwood 3090, I can't control the volume separately to the speakers.  I can only control the volume of the receiver speakers via switch on the satellite to the receiver.  The sound of the television is stronger than my receiver speakers and smother them.  Therefore, I don't get a good stereo separation.  With my Kenwood 3090, I could put the TV on mute and listen to the sound of the TV through my receiver speakers (which are much better).  Any way to do cela with the SONY STR-DH130.

    Thanks in advance

    Bookman

    If your audio connection cords catch AUDIO OUT of the Sony KV24FV12 TV to the AUDIO IN ports of your STR-DH130 A / V receiver then you can turn off the TV speaker, AUDIO OUT option FIXED value so that you can adjust the volume of the TV via the remote control of your receiver. (see pages 19 and 20 of the TV Manual)

  • Satellite P300 - output HDMI does not connect to the model of TV Samsung LE32B450

    When I use the Toshiba "HDMI" out utility to connect my Satellite P300 - 19K to my Samsung LE35B450 TV, I get the message "it is only effective when the PC is connected to a TV set that supports HDMI control via the HDMI cable.

    Does anyone have a solution for this? My Samsung TV is newer and has 3 HDMI input jacks and the same result. Is there another driver from Toshiba not requiring this vibration control function? This seems hardly reasonable given that all I want to do is display & there is normally no 2 communication channels via a HDMI cable anyway.

    Thanks in advance for any help there.

    I m not 100% sure, but I think that in s manuals is described clearly that this tool is designed for use with Toshiba Regza TV. With other words, it is Toshiba specific function.

    If you want to have the photo on your standard procedure for TV use for this purpose connect the laptop to your TV using a HDMI cable, turn on the port HDMI (HDMI channel) on the TV and use the combination of keys FN + F5 to switch between laptop and TV.

Maybe you are looking for

  • Satellite P25 video i/o does not.

    My Satellite P25 provided with a card that's where would be a CD player. Its cable TV tuner works very well, but the problem is the other port on the card, which attaches to the (white, red, yellow) RCA cable. I don't know yet what it serves, but I t

  • Satellite P100 - 434 BSOD boot problem

    Hello everyone! I have laptop Toshiba Satellite P100-434 and lately I encountered many problems during startup. 1. the laptop starts normally until the entry of the password. Then, in the middle of typing BSOD.2. the laptop gets BSOD or turns off 2 s

  • Satellite Pro P300 - after Truesuite update I can't open protected files

    HelloSorry for my bad English, but I came to Italy, and here we do not have any forum that can solve my problem. I have a Toshiba laptop pro P300 with fingerprint reader. I use fingerprints to log and protect certain files, simply out of curiosity, h

  • Satellite L650-PSK1EA-06L02F - where are the specifications?

    I'm looking to buy some RAM to upgrade for laptop computer to my father, but Toshiba support page lists absolutely nothing under specifications tab for this model.http://www.MyToshiba.com.au/support/computers/satellite/L650/psk1ea-06l02f/specificatio

  • Compaq presario c700-c795tu: unable to connect to the WiFi network with WPA2 encryption

    Hi team, I tried all the options in your post and I am still unable to connect to WiFi with WPA2-PSK encryption. I am currently using the adapter network driver atheros 5007 wireless. Some of the links in your message that resolved this issue earlier