IX2 - DL does not start after the firmware update and now in boot loop contant with double red lights

I just applied the update to the latest firmware 4.1.208.33789 for my IX2 - DL and it took an extremely long time to reboot - flashing white light for 20 min on the right.

Shooting and by unplugging power did the same result.

I hold the reset button hardware pin and now he's in a boot loop throw up double red lights and then attempt to restart with flashing blue white and strong.

Help! don't know what to do next.

Hello steveappcity,

I recommend a support incident, opening the only way I can support an imager is if she is officially released:
https://Lenovo-na-en.custhelp.com/app/ask/

Tags: Lenovo Products

Similar Questions

  • IX2 - dl does not start after the firmware update

    I bought my ix2 - dl last three days ago and then she starting with 2 new readers just to test it worked using Mac and Windows then a firmware update version 4.0.8.23976 appeared available via the web interface.

    After the update and reboot, it no longer starts with white LED blinking forever. I waited for 20 hours.

    The reset and power keys doen't work until the device starts as I suspect.

    Is it possible to install the old version of work or reset the dx2 another way?

    # The upgrade was successfully without interruption of power supply and interface asked to restart.

    I contacted the local support for RMA.

  • HP DV7-7259nr does not start after the BIOS update

    Hello

    I have a problem with my HP DV7-7259nr laptop, WIN8 running: it does not start after tune recommended to update BIOS and drivers.

    It downloaded all the drivers and started installing at one time, he asked for a reboot, click OK and the BIOS update has begun to load. The process ended successfully and after the reboot that my laptop wouldn't start; everything is black and the cooler is runing.

    I tried:

    -battery disconnected and power - button Power - plugged power again-> NOTHING

    -Windows key + B + Power button--> nothing

    Please help as this is the laptop I use daily in my work.

    Thank you

    If you install the electro mechanical original hard drive in it starts?

    If it has been delivered with a SSD?

    The specifications indicate that an electromechanical drive was part of the specification.

    This is where lies the UEFI environment. It is actually on the hard drive.

  • Lightroom cc 2015 does not start after the recent update on Mac Pro Yosemite

    After you download the last updated September 27, lightroom does not start on my mac.

    Used to work without problems so far.

    Tried to disconnect the last clouds and again without success.

    Thanks, that worked.

    Now, I have to do the update again hope that will work as well...

    Do you have any idea what caused the problem?

    Concerning

    Christian

    MIT thank wurde

    Hans Christian Behrendt

    2015-09-30 18:07 GMT + 02:00 rpandita [email protected]>:

    Lightroom cc 2015 does not start after that a recent update on Mac Pro Yosemite creates

    by rpandita https://forums.adobe.com/people/rpandita> in * Photoshop

    Lightroom *-see complete discussion

    https://forums.Adobe.com/message/8015642#8015642>

  • Tecra 8000 does not start after the BIOS update

    From one day to the other does not start my Tecra 8000 (400 MHz/256 MB BIOS 9.30 for years). After start-up, the disc starts to turn, but the screen including the backlight remains completely black, without red logo TOSHIBA BIOS is not accessible.

    I got a new mainboard on stock, so I replaced it, and it worked. Unfortunately now my WLAN card now did not work properly. I tried several settings of the BIOS with no results, so I decided to do an update of the BIOS from 7.50 to 9: 30. After the upgrade, I get the message "ROM WRITE successful, utility completed. LEADER BIOS: Tecra8000 v 9,30 ". Because what either kept silent, I pressed the power button to restart and heard a long and many short beeps (endless). I could interrupt what pressing the powerbutton for 5s.

    After turning on again I have the same problem as described in the first line :-( I can't get into the BIOS, but I can again update (with pressed F12). Once again these beeps.

    What to do with these beeps after average BIOS update? I replaced the MoBo connector LED with pension. Processor, memory, keyboard and HD has remained the same. So, before I start disassembling the machine, please notify, your help is very appreciated.

    Hello Joachim

    I'm not a technician and don t know what the beeps but I am afraid that the BIOS chip is damaged. Because of this, the unit is completely dead. Sorry, but I really don t believe you can do anything. Maybe the new motherboard again :(

  • A series of satellite does not start after the BIOS update

    After update bios with the downloaded utility my laptop does not start.
    Do you have this case covered by the warranty?

    I'm not sure if this would be covered by the warranty. You must contact the ASP in your country for details, but I assume that it s not covered.

    PS: Did you try this work around:
    -remove the battery, disconnect the adapter
    -wait ~ 40 min
    -connect the two devices again and try to turn on the laptop

  • HP compaq 6510 b does not start after the BIOS update

    Hello

    When I turn on my laptop HP compaq 6510 b it DISPLAYS this message: your bios has not finished updating 6510b.after flashing the bios of the laptop does not start .it displays the same message (your bios did not complete the 6510 b update) and turns off. I cannot access the bios by pressing F10.the bios version was F16 and flash by F20 .will help thank you very much.

    I'll have to return a verdict of laptop motherboard bricked due to a failure of the BIOS upgrade. Sorry, but it happens.

    This means that this would require the replacement of the BIOS chip to make it work again.

  • Satellite A200-1If does not start after the BIOS update

    Hello

    It is my first time on the forum posting, I hope someone can help me.
    I recently downloaded the latest update of the Bios (bios - 20090121132526.zip) for my laptop. I ran the bios Setup, after the update it restarted my laptop, but then he went to a black screen and no longer start.
    When I press the power button only power led lights, fans begin to turn and the DVD - rom turns and stops and the screen is blank.
    I am running Vista Home premium 32-bit.

    Can anyone provide a solution on what I can do to fix this?

    Was the system standby standby/extended/recovery?

    Its important to cold starts of the system before and after an update of the BIOS.

    You could try to remove one of the modules RAM (change RAM size) and turn on, otherwise the system may need to be sent to an ASP for repair.

  • Z50-75, does not start after the bios update

    Hi all!

    I just baught Z50-75 with AMD FX7500, 8 GB of Ram and FreeDOS. I installed Windows Pro 8.1 and they shot a few drivers during the installation and I went to the view of Lenovo and downloaded all the rest (graphics, camera, etc.), after each installation the computer restarted normally and everything was OK The latest drivers I've seen on the site were originally from the BIOS and I downloaded those to and he started the installation, after which he said: "the system will now restart for the changes to take effect" and he did, but it wouldn't start after he did that show me this on the screen:

    And I tried both options (either with the Windows CD inside), but it just stays where it is, no effect.

    I can enter the bios and change the settings, but none of them seem to work because that's the maximum where it will go, the only difference is when I change from AHCI to compatibility mode, it restarts and I get a white screen, I have to use a button recovery to return to the image above...

    I appriciate any help kond, please give me some advice.

    Thanks for the reply!

    I solved the problem after updating the bios, communication between it and the disk hard drive had a few problems and is causing the boot problem. I solved with out the hard drive and install on another laptop, flashed the windows and installed the hard back in my Lenovo, and that worked.

    You tell the truth, I don't really know how it was the solution, but it worked, I guess that Flash just windows helped the hard disk to create the new connection to the bios, that the first was simply corrupted by an error during the update of the bios...

    Now, I know that the bios update is the last solution I'll never use, and of course, save all peace of data I had on the hard drive if possible.

  • Satellite L855 does not start after the BIOS update

    I downloaded the BIOS update and followed the instructions there during the installation, but on reboot (including the requested configuration), I get a blank screen. Intermittently, the CPU fan starts and stops. I think that the BIOS update failed, how to solve this problem?

    Thank you
    Neil.

    Hello, Neil

    In General when the BIOS is screwed up you need professional help and you should contact the nearest Toshiba service provider and ask for help.

    See also this thread. Perhaps this methid can help you too.

  • Area 51 ALX - does not start after the BIOS update - still in warranty

    I was preparing my Area 51 ALX for Windows 8 (pre-ordered and expect it to be here Friday) and decided to update the BIOS to the A10 A11. Back on and now it just sits here with no output monitor and my keyboard/mouse TactX™ is not illuminated either. Fans seem to be 100% / 70%. I tried to reset the CMOS and nothing. I'm just here? The office is still under warranty until next February, I believe. I am disgusted seriously now because I looked forward to Windows 8, "Painkiller hell &.

    "and to get some done coding. What a a day of . Don't know if this can help my case but I have been a customer for a long time from the time of Dell before. Had an old P2 Area 51, bought the m11x at launch and was still in talks with Ross Anthony to make a site of 'history' (although never, he eventually happen). I'm sure that set my m11x Win 8 will not work because it is stuck on super old graphics drivers. Can someone from Dell please help me here? Also, if I'm , is it possible to simply replace the motherboard myself? There are lots of tips on eBay.

    At this point, there is a strong chance that the motherboard is brick and needs to be replaced. Fact he complete the update of the BIOS and restart on its own, or force you the reboot?

  • Satellite L50-A-160 does not start after the Bios Update

    Hi, first of all, this is first post.

    I have 2 satellite L50-A-160 with bios 1.1

    Problem: seems to go to sleep after a few minutes, even working on them (even with both)

    So, I found an updated version 1.9, downloaded and running on one of the laptops. the biosupdate tool found matching the BIOS and a race.
    In the middle of flashing, he fell asleep. turned on and not start. What can I do? Recovery options? I guess the same thing will happen with the other too...

    What is the problem with these computers?

    Besides; very poor battery, always shows 0% available and not charging...
    Does anyone have a solution?

    Best regards
    -always in the hope.
    GT

    Have you tried to change in Power Options?

    See screenshot and try to change the ones I marked (it can refresh the settings, just change the values) and see if this solves the problem.

    and for the other laptop with no boot, a laptop sleep by updating the bios will surely mess it.

    what I don't understand is why your sleep laptop BIOS update, as far as I know the sleep settings is active then on windows (since this is controlled by windows)
    He does not sleep while in the BIOS you leave 1 year, sleep settings active only after loading windows.

    have you tried to check the time of processor for your laptop? Maybe its overheating causing auto-off

  • Satellite A100 - BIOS and Windows does not start after the BIOS update

    Hello, I extend my Satellite A100 laptop BIOS.

    After update, I can't start my laptop and the BIOS will not start.

    You see the Toshiba logo?

    Was there a power failure when you updated the BIOS?

    Try to remove the battery and the adapter and leave for a few hours. You can also try reinstalling the RAM.

    If this does not help, you will need to send it to a Service Center for repair.

  • Satellite L350 - does not start after the BIOS update

    Hello

    I recently (yesterday) downloaded the latest version of bios update dated dated 25/02/10 2: 20 - WIN, after download and does run the software from the laptop immediately stopped working and stop. I am now no longer able to boot up the laptop at all, all I get is the power light on and the hard disk light flashes, I hear the spinning CD/DVD drive, but what is not screen anything, I don't think this is the start.

    Is there a way to fix this without taking it to a store/engineer, BIOS recovery?

    The laptop is a Satellite L350, I opened the laptop to try to reset the CMOS by removing the card mother battery (not sure if it would have helped), but as much as I know it doesn't have an or I'm not.

    Any help would be greatly appreciated.

    Thank you

    Andy

    Hi Andy,.

    Hmm... If the BIOS update failed, you can't do anything because only an authorized service provider has professional diagnostic and recovery tools to redo an update.

    So in my opinion, you must contact a service provider authorized in your country. Get in touch with the guy and ask for help. They will tell you what to do now.

    Here is their list:
    http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

    Good luck! :)

  • HP Pavilion dv9260nr does not start after the bios update

    After the HP Health Check, it was recommended that I have updated to the current bios.  After you have downloaded and installed, the computer would not start.  Instead, it emits a long beep and 2 short beeps and the screen is blank.  How can I recover a bios update failed?  Is there a way to return the computer to the bios Setup?

    I thought I would post here to help others as I just spent 5 hours to fix this problem. I have personally experienced this on two different computers, both are model DV9260NR. I woke up in the long and short two beep power. The first time it happened, I tried to fix the BIOS by using the recovery disk, but it didn't work. I tried this using a USB floppy like any other player. The floppy drive should get accessible, then machine would be on a second beep then stop, but it would remain under tension. The first time around I gave up and eventually return it to HP as it was under warranty. This time above the current problem computer is more under warranty so I decided to test out of old college. After trying several discs crisis different Phoenix, I finally found one that worked.

    I downloaded crisdisk.zip here:

    http://www.mediafire.com/?3ccb9m0kv0m

    Followed by the latest bios from HP for the DV9260NR

    FTP://ftp.HP.com/pub/SoftPaq/sp42001-42500/sp42187.exe

    I used 7 - zip to extract the files in sp42187.exe and crisdisk.zip

    go to the folder where you extracted sp42187.exe and rename it to 30BBF2D. WPH into the BIOS. WPH

    Copy BIOS.wph to the folder where your snippet CRISDISK.zip

    I have created my disk in Vista, so don't worry about going "Real DOS".

    YOU MUST USE CRISDISK TO CREATE THE DISC!  SIMPLY COPY THE RIGHT FILES ON A FLOPPY DISK DID NOT WORK!

    Open a command prompt, I used command.com not cmd.exe

    CD to the folder CRISDISK.

    At the prompt enter: "CRISDISK. "BAT HAS:

    Finally, put in a blank disk and follow the instructions.

    Once the disk created, slap this puppy in a floppy USB drive and plug it into the computer.  I didn't need to use as or Windows + B, B FN hotkeys to trigger the BIOS recovery. The system entered in the BIOS for me recovery mode and tried to access the USB floppy.  I noticed that not all USB ports will work.  I plugged my USB stick, floppy to the next to the power supply.  If all goes well just turn on the computer with connected USB floppy drive and the disc in the drive. As before the system beeps once per second during playback of the disc.  The disk activity, arrested again, but this time that the system kept beep immediately after discontinuation of access to the drive.  These beeps point you out that the BIOS is flashed, it's just leave turn. When it was made the machine itself set off.  If yours is not, so I doubt that the BIOS recovery will succeed. I then unplugged the USB floppy drive, turned on again and to my surprise I was greeted by the HP and the BIOS logo!  I hope this helps people difficulty of their DV9260NR.  I met four dv9260nr machines and two of them does not update the BIOS using WinPhlash and the finished machine trashed, not good statistically.  I hope that others with the same model will be able to get their machinery running. I'd be curious to know if it works for others.  Post here if you are or do not succeed using this procedure. Good luck!

Maybe you are looking for

  • What a bunch of choose what wrist size is > 220 mm

    The size of my wrist is a little more then 220 millimeters. I would buy 2 Watch with nylon band. Don't you think that it fits? Tips that will strip to adapt? 3 options of party? Tanks, Martin

  • links to web sites are green, but not in IE

    example site www.unc.edu/ ~rowlett/units/index.html all links are in pale green and impossible to read Flags of the world site shows the same problem. In IE8, there is no problem, but I can't print the page.

  • Formula need to count cells based on the number of week

    I have a table used to track dates of contact with a client.  A column calculates the WEEKNUM of the date of contact. Week NUM Date First name 2 04/01/2016 Amanda 3 16/01/2016 Robert 4 17/01/2016 Rosie 6 01/02/2016 John 6 02/02/2016 Soledad 9 21/02/2

  • HP DV6 2 overheating GPU

    Hey guys. I have this HP Pavilion DV6-6100SE(AMD A6-3410MX). I had the radiator replaced at Hp there, because I had the problem of heating of 6 months. Now, it's even worse than before. It has two GPUS. AMD 2-6755. The Gpu2 happens at 91 degrees idle

  • DMP files

    Hi, please can someone look at this dmp file and let me know is originally my PC problems whenever it starts. http://sdrv.Ms/19Aa2Lw Thank you