Jabra M5390 driver problem

Similar Questions

• Dedicated graphics (A1398) driver problem

  My Macbook Pro (A1398) dedicated card (Geforce GT650M) graphics driver problem.

  Installation of the drivers of web from Nvidia (WebDriver - 346.03.10f02.dmg, WebDriver - 346.03.10f01.dmg, WebDriver - 346.03.10 b 01 .dmg) with CUDA drivers (cudadriver - 7.5.29 - macos.dmg) and toolboxes CUDA (cuda_8.0.29_mac.dmg and cuda_7.5.27_mac.dmg) does NOT.

  When I tried to install Caffè/CUDA (used for Machine learning), my card (Geforce GT650M) dedicated graphics card driver has become corrupt (seen through the Console).

  Dedicated card random is more gets reported under 'report system' (probably due to the problem of driver).

  Attempts to restore have been hit and Miss so far.

  I downloaded the drivers from Nvidia web (WebDriver - 346.03.10f02.dmg, WebDriver - 346.03.10f01.dmg, WebDriver - 346.03.10 b 01 .dmg) but they have only worked / failed randomly when combined with CUDA drivers (cudadriver - 7.5.29 - macos.dmg) and toolboxes CUDA (cuda_8.0.29_mac.dmg and cuda_7.5.27_mac.dmg).

  Only the internal graphics card Intel Graphics 4000 is constantly working.

  I cleaned the system (by removing all traces of the nvidia drivers and drivers of coda) while that to reinstall these drivers in different combinations.

  Yet, the conclusion is that it is all the success and the miss.

  Sometimes it worked I could test samples CUDA.

  Other times, that it worked, but the laptop would freeze randomly.

  Then, he failed once again and returned to map internal Intel completely.

  It was suggested that I should be able to restore it by reinstalling ElCapitan

  I don't have the luxury of reinstall ElCapitan.

  Is there a way to access the Apple drivers without having to reinstall OS x.

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

  This could be your problem:

  http://www.Apple.com/support/MacBookPro-videoissues/

  Need to reinstall OSX to reinstall the Apple drivers.

• Driver problem

  I think I have a driver problem. Installed the 9.3.1 version recently.  Always get an error message and cannot connect to Safari.

  What is the exact error message?  You can try another web browser: chrome, firefox, etc.

  E-mail work?

  R

• -Portege Z10t 13 V graphic driver problems and lag with W10

  Hello

  Please excuse my bad English,

  I just bought the Z10t A 13V PT 141, with W8.1. This computer works fine on W8, but I want to install W10. I already tried 3 times but each time, the cursor (with the touch pad or mouse) is lagging behind, each movement is jerky and works very well. I tried to see if it was a driver problem and downloaded new drivers from Toshiba for the W10.

  I did the same thing with Intel drivers, but for graphics drivers, there is an error message: "a custom computer manufacturer driver is installed on your computer. The Intel driver update utiliy is not able to update the driver. Install a generic Intel driver instead of the driver from the computer manufacturer custom can cause technical problems. Contact your computer manufacturer for the latest driver for your computer.

  When I'm with W8, drivers are correctly updated...

  So I think that the cursor problem is due to this driver problem (I hope so, but I'm not sure). What is the solution? I'M alone with this problem?

  Thank you

  Thomas

  Hello Thomas,.

  EXACTLY the same problem here with my uograded Portege Z10t-A-140 to WIN 10.
  I also took the same steps and encountered the same problems and no solution.
  I find Toshiba after sale customer VERY INEFFECTIVE and disappointing, because it seems no way to get a support PROFESSIONAL from Toshiba on this issue (or any other for that matter).
  Note that I absolutely do not consider helping other users on a forum or self-help a form of professional support at all!
  -> Not happy with Toshiba!

• Sound driver problems

  Hello world

  I reinstalled windows in my computer after you have removed all the files it contains.

  Therefore, I unfortunately lost the recovery partition.

  Now, after you have reinstalled the Windows 8 Pro, I installed all the drivers and everything works normally except the sound.

  However, I have been using Ubuntu after reinstaled Windows and I DIND'T have no problem with that.

  I thought that maybe this could be a problem inside, but when I use me headphones, or when I use my computer with my TV with HDMI, the problem persists.

  My computer is a HP ENVY m6-k010dx Sleekbook.

  So, what shoul I do to have it fixed?

  (Sorry for my bad English )

  ---------------- UPDATE ----------------

  I use a Linux Live USB to test the sound, as it could be any physical problem.

  However, it turned out that it really is a driver problem.

  I found a solution

  Just after installing Windows 8.1 the problem fixed itself

  Thanks for your help ():

• My cd rom seems to have a driver problem

  Hello

  My cd rom seems to have been corrupted and I have a message from code 39. How can I use my recovery disks when the cd rom is not working. I have an old computer that has XP loaded, I can load my inside recovery disks & copy on an external hard drive and then copy it on my laptop which is a HP Pavilion dv - 7 3111ea.

  Thank you

  Hello

  Unfortunately, it is not possible to do what you suggest.

  However, the CD/DVD drive should still work with your recovery disks (unless there is a hardware problem with the drive), because when you start the laptop computer, the drive is controlled by the Bios, no windows - code 39 refers to a driver problem Windows.

  You may be able to correct the error of the Windows driver as follows.

  First, try the automated Microsoft fixit at the link below.

  Windows 7

  Vista

  Check if the drive works now.

  If the drive does not, in the Menu start, open all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.

  sfc/scannow                (Note that there is a space between sfc and /)

  Let the entire process, then the output type and press ENTER.  Reboot the laptop.

  When windows is completely reloaded, click on the Start Menu, open Control Panel and click Device Manager.  Click to open the CD/DVD-ROM drives.  Right-click on the drive and choose uninstall.  Do not delete if requested drivers.  When the device has been uninstalled click the icon 'Search for hardware changes' (usually just below help in the toolbar).  Let windows reinstall the disc and see if it works now.

  

  Kind regards

  DP - K

• Driver problem with a dc7100 cmt

  I have a driver with my Hp dc7100 cmt tour 7 months ago, I upgraded Windows Xp pro to Windows 7 Edition System Home Premium, it was working fine... or so I thought, then week or so I did a Windows update that has problems starting

  Windows 7 upgrade advisor has been downloaded in my system, I started to have a driver problem he always tells me to update my drivers for systems, I well updated some drivers but I was not of the most important of them.  It is a Graphics driver (WDDW) driver for windows aero graphics would work my CD-Room go stale and USP port pilot who was also outdated... The player windows Media have also stopped...  He told me to contact my PC manufacturer or retailer to see it an upgrade is available, I've been looking and asking for two days... I hope someone reading this and can give me some advice on how I can get these updates, or tell me why I can't get HP... My goal is not to get out a purchase of a new system, but fix the one I have... as a student, my funds are very low!  Pease Help, thank you

  Hello:

  What graphics card you have in your PC?

  You mentioned Aero, and you wouldn't get Aero on a dc7100 with the integrated Intel graphics card.

  You'd only Aero, if you have a PCIe x 16 graphics card is windows 7 capable.

  If you have the Intel integrated video card, I got something that will install the video driver, but you won't have Aero.

  In addition, he will work for W7 32 bit.

  So, please post back and let me know what video card you have in the PC, because if it's an add-on, one, I would need to know the manufacturer and model.

  Paul

• Tecra 8000 SD 2102 DVD Drive problem

  Hello

  I have a Tecra 8000 with a 2102 sd drive, the drive may be used if I boot from a boot disk, but has driver problems when used in Win 2 k. Anyone has any ideas, what is the problem?

  Dave N

  Hello

  a http://www.toshiba-europe.com/storage/index.asp?nav=HOM&page=HOM&frame=home, you can find more information on your drive!

  Choose your player and download the device driver. This should solve your problem!

  Good bye

• Qosmio F60 turning is not on - HARD drive problem

  My F60 running stock windows 7 and when I turn it on I get a black screen with the following text:

  + Check the file system on C: +.
  + the type of file system is NTFS.
  + Volume name is s3a5802d002 +.
  + One of your disks needs to be checked for conisitency. +
  + You can cancel the disk check, but it is strongly recommended that you continue.
  + To skip verification of the disc, press any key within 10 seconds.

  If I leave it just like that.
  I try to ignore it, and it does not work so I turn it off and go again on the third time, to turn on while I press ESC. What should I do about it?

  Re: do everything or send it as it is only 6 months old, it is Bernard did this for 5 months

  Hello

  It sounds a bit like a HARD drive problem.
  I recommend checking out the HARD drive using a free tool called Drive Fitness Test
  This free tool allows you to get more details on the State of the HARD drive and maybe some error would be detected which would mean that HARD drive failures and disk HARD must be replaced.

• 1000 - 1b09AU: driver problem

  Hallo.

  I would ask, there some driver problem happening on my laptop.

  That is the problem.

  The retailer installed OS is Windows 8 Pro inactive. The laptop works well, but there are a few problems of brightness.

  When I decrease the brightness, the brightness is returned to brighter level, even when brightness is 40%.

  The following illustrates.

  100% - the brighter.

  Reduction 90% - approximately 30% darker than before

  80% - reduced 30% darker.

  70% - to the brightest level.

  And continues up to 10%. But it's OK.

  Now, when I reinstall Windows to 8.1, even the brightness decreases. Always in the brighter level, it makes my eyes sore.

  And when I check for Device Manager, the graphics card displays 'Microsoft Basic Poster' instead of 'Radeon HD Graphics 6480 G '.

  I think that I have installed the driver properly. Even I ran the installer of the pilot twice or more.

  When I approached the extractor frome pilot the retailer where I bought it (the seller gave me a copy of the drivers for the laptop on my HARD drive), there was something wrong. My graphics card is not mentioned in the support and functionality of device. I was disappointed. I think that the retailer has made a mistake.

  Now, after I checked the official download link, I opened the linkand what comments? My display driver is not in the list! I was disappointed, once again.

  Can I download the driver from the official site AMD? this one?

  If not, is there a solution of HP?

  I'll wait.

  Oh one more. I hope I don't have to create a new topic for this issue.

  The sleep option is also disappearing. It's never happen before I upgraded to Windows 8.1.

  Thanks for your help.

  Hello:

  Since there is no graphics driver HP W8.1, your only option would be to try that one directly from AMD.

  Unless you get a graphics driver to install, there is no option of sleep.

• Alternative to the reset by Satellite A660 for potential HARD drive problem

  In the last week or two, I got a few blue screens, saying he was driving demand, and that windows must be shut down to avoid damage my computer.

  I have just restart and continue working.
  The last time it happened, I had repeatedly "initialization failed" and it says hdd, SDS, fdd. If I pressed the power button until I didn't see no signs of activity, then started. Things went well. I called Toshiba support and they recommended that I go home and save my files before continuing. It took hours selectively to clean, sort the previous backups, and a small footprint of the backup system.

  When I called Toshiba once again, they recommended a "takeover", which is restoring the factory settings. It puts me in the stone age. I have to go through a never-ending process of the upgrade to Windows 7 Pro 64-bit, install and reconfigure all the applications and environments/configurations, etc. It will essentially take on holiday, if not more. I'll also have to get another computer (maybe a netbook) to stay in touch while I restart my laptop. It's barely more than a year.

  Is there a diagnosis I can do to determine the probability that there is a hard drive problem? Support for Toshiba said that is the surest way, because it provides a diagnostic F10 for the hard disk code, and it also pushes the bad sectors at the end of the disc (logically, I suppose, since you can't physically move a fault).

  > About Hitachi DFT, is it important that my HARD drive is Toshiba mk6465gsx? This is what is displayed "Hard drives" in the Device Manager.

  It s no matter what HARD drive manufacturer, it is the Drive Fitness Test is able to scan all hard drives to find errors.

  > Also, http://www.hitachigst.com/support/downloads/#DFTshows links to create boot disks, but I was wondering if I could create a bootable instead.

  Not sure if this is possible if there is that one option to create a startup disk, and then a flash stick does not work. But of course you can try this out.

  > This laptop does not come with a floppy drive, and I still create coasters trying to burn discs.
  You don't need the floppy drive, the tool must create a disk bootable (CD)

  > I guess that the same question can be asked on Memtest86. Another issue is the relevance of Memtest86 for my system. My c drive has a "Program Files" folder, but also a "Program Files (x 86)" folder for 32-bit applications. Memtest86 is for the x 86 architecture. I don't know if my 64-bit Windows 7 involves a non - x 86 architecture.

  I guess that Memtest86 should also work on Win 7 64 bit systems. But also the MemTest 4.20 is 64-bit capable

• Satellite L500 - 1CQ PSLS0E - CD/DVD drive does not work - driver problem?

  Hello

  My DVD player does not work.

  There is power to it. The engine turns when I eject and reinsert. Troubleshooting Control Panel for the equipment and devices said it is a driver problem, but cannot fix it. Problem with the driver.

  I reinstalled it from the Toshiba site.
  It records in the right place?
  I am Windows 7 64 bit and chose the right driver for it.

  Should I use the 64-bit?
  I have 3 MB of RAM which was the spec when bought.

  If I wanted to change to 32 bit how you take you without the CD/DVD drive?
  Is there any point in doing this?

  Thank you

  Richard

  Hello

  To be honest I m a bit confused.
  You are not able to boot from THE disks; Windows disk, disk recovery, disk Linux?

  If it of the case, then it means that your CD/DVD drive is faulty.
  Why? Because the CD/DVD drive is recognized and controlled by the BIOS when booting from CD or DVD.

  When the Windows operating system has started, the CD/DVD drive must use the Microsoft common driver which is part of the Windows operating system.
  This means that you n t need to install ALL the drivers in order to get the job of CD/DVD.

  If you can boot from any disk, but if the CD/DVD drive is not recognized by MY computer, then I recommend this:
  http://support.Microsoft.com/kb/270008/en-us

  Before you remove the upper and lower registry filters, remove the CD/DVD drive in Device Manager and then go into the registry and remove the filters. Restart the unit.

  Good luck

• The conclusion for M - Audio MobilePre USB driver problem

  The conclusion for M - Audio MobilePre USB driver problem

  Use: iMac

  OS: El Capitan 1011.2

  The latest driver I could find was 1.8.1.

  Error message:

  Installation failed - Setup could not install the software because there was no

  available software

  I would use this hardware with Final Cut ProX 10.2.2 and Garageband 10.1.0.1

  A quick search seems to indicate the latest version of the driver to be 1.2.1 - there was no 1.8.1 I could find. It has been out for more than a year, so no mention of El Capitan, but it could work. I'll make sure that you have the right to download and try again.

• Satellite L300 17L - audio driver problems

  Audio driver problems, I use Windows XP SP2, I installed the MS patches, but still there is no sound.

  And in the control panel in the sound section says that there is no audio driver installed.

  I need help please!

  Hello!

  It s a known issue and when you search a bit in the forum you will find a large number of publications on this subject.

  Remove the sound card from the Device Manager and the high definition Audio Controller from Device Manager.
  And then update Windows with KB835221 & KB888111 patch, reboot several times, and then you can install the driver from Realtek but download and install Realtek driver directly.

  Good bye

• Spectrum 13D-3000 Downgrade to Windows 7 - driver problem

  Previously, I've killed my spectrum 13D-3000 for Windows 7 Home Premium with the help on the forum.  However, I still have a driver problem, I want to solve it.

  Pilot's Watch "Intel (R) 8 series xHCI HC - 9 31' that is not installed (Code 28) with yellow! icon.  Hardware ID values are:

  PCI\VEN_8086 & DEV_9C31 & SUBSYS_1911103C & REV_04
  PCI\VEN_8086 & DEV_9C31 & SUBSYS_1911103C
  PCI\VEN_8086 & DEV_9C31 & CC_0C0330
  PCI\VEN_8086 & DEV_9C31 & CC_0C03

  Thank you for your help.

  Hello:

  This is the USB 3 controller that needs a driver.  It should work...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-127803-1&cc=us&DLC=en&LC=en&OS=4063&product=6521374&sw_lang=