JetDirect MIO card JetDirect J2556: memory required for?

I want a JetDirect MIO card for an old LaserJet 4 Plus. I was watching a JetDirect J2556. However, I have read that the printer needs 16 MB of memory for the card to operate. Is this true? I read on one website. The site sells memory and maps MIO. I tried to find a PDF or a manual or something HP which specifies the requirements for the card but I had no luck it is.

Devices have usually minimum 16 MB of memory when the functions of duplex and network available and no less than 8 MB for devices with function.

I think that alghough the Jetdirect card may have installed/configured for use with less than 16 MB of memory, but you may experience performance problems if memory is low.

Tags: HP Printers

Similar Questions

  • The amount of space (memory) required for the good functioning of Firefox?

    The amount of memory required for the operation of Firefox? Trying to decide between IE and Firefox. Research in the new computer and need to think about which browser to use, and how much space it needs to work properly.

    You need no more than 40 MB for the operation of Firefox.

  • I plan to upgrade my OS to El Capitan.  What are the processor speed and memory required for the operating system works well?

    I plan to upgrade my OS to El Capitan.  What are the processor speed and memory required for the operating system works well?

    I use a processor 2.3 GHz Intel Core i5 with DDR3 4 GB 1333 MHz memory.

    My last similar attempt on another machine resulted in a very slow computer.

    Thanks, Ron

    Apple says the following:

    General requirements

    • OS X 10.6.8 or later version
    • 2 GB memory
    • 8.8 GB of available storage

    For best performance, I would say not less 4 GB and preferably 8 GB or more.

    Your i5 is well able to support properly.

    http://www.Apple.com/OSX/how-to-upgrade/#Hardware Configuration

  • Error FSX Gold - "the graphics card does not minimum requirements for support of shader."

    I just bought FSX Gold and I have installed two of them, but when I click to open it it says "the graphics card does not meet the minimum requirements for the support of shader. This product requires a geForce3/Radeon8500 class or a better graphics card. Flight Simulator will now quit. "I went to support to see what happened and he said the need Shader 1.1 or later so I checked my Shader and he said he was Shader 2.0. you guys can tell me what's wrong.

    Details:
    CPU -  Intel (r) Core (TM) 2 CPU Quad Q6600 @ 2.40 GHz
    Speed of the CPU to 2.4 GHz Performance rated at: 5.28 GHz
    GB OF RAM - 6.0
    OS - Microsoft Windows Vista Home Premium Edition Service Pack 2 (build 6002), 64 - bit
    Video card - Intel (r) G33/G31 Express Chipset Family

    • Video RAM - 287.0 MB
    • 3D - Yes
    • Hardware T & L - No.
    • Pixel Shader Version - 2.0
    • Vertex Shader Version-2. 0a

    Version of DirectX-11, 0
    Sound Card - Realtek High Definition Audio
    Free disk space - 356.3
    DVD - ROM - HL-DT-ST DVD-RAM GH10L

    That's all. I hope you can help!

    Hi Man Com,.

    I suggest updating the video drivers from the manufacturer's Web site and make sure that direct X is enabled in the graphics card Control Panel conrtol.
    For more information, you can consult the following articles:
    Updated a hardware driver that is not working properly

    The problems of the game performance

    You can also read the following article and see if it helps.

    Solving graphic problems in Flight Simulator X

    Hope this information is useful.

  • Memory required for the upgrade of IDS Sensor 4.1 (5) to 5.0 (IPS)

    pls tell me the desired memory minimum for the sensor IDS version 4.1 upgrade (5) to version 5.0 (IPS)

    Detectors of the series 4200 ID must be at least 512 MB for this upgrade to 5.0.

    Read the release notes for more information:

    http://www.Cisco.com/en/us/products/HW/vpndevc/PS4077/prod_release_note09186a008045ab52.html

    I hope this helps. all the best... the rate of responses if deemed useful...

    Concerning

    REDA

  • memory required for simultaneous users on the side application in r12

    Hi please say how much memory will be needed for the concurrent users on demand side and secondary databases for example 100 users requires memory xxx?

    Edited by: 834708 February 22, 2011 20:59

    Please see old similar threads.

    http://forums.Oracle.com/forums/search.jspa?threadID=&q=hardware+specification&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001
    http://forums.Oracle.com/forums/search.jspa?threadID=&q=hardware+sizing&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001
    http://forums.Oracle.com/forums/search.jspa?threadID=&q=benchmark&objid=C3&DateRange=all&userid=&NumResults=15&rankBy=10001

    Thank you
    Hussein

  • What is absolute minimum Plug and the memory required for the performance of modern editions of Firefox?

    I am running a machine Windows XP Service Pack 3 on 512 MB of ram and I am perfectly happy with Firefox 28. But I considered up-to-date. However I'm not sure that my machine can handle anything beyond version 28 and 29 (which I didn't like and so back to 28 anyway) it is interesting trying to update, or do I stay with what I have?

    Hello

    You can check the system requirements here:

    It is highly recommended that you update to the latest Firefox to keep up-to-date with security updates. Note that if you don't like the interface for Firefox 29 +, there are extensions that can return the theme of an interface, you are more at ease.

    For more information on the themes of Firefox, see the article use themes to change the appearance of Firefox.

  • Video card: driver Windows 10 required for the video card Part No.: 5188-4289

    Hello

    My computer which is built from individual components suddenly upgraded to windows 10 by himself. Now the screen is not good and I tried to change the settings but, the display is even worse. The graphics card that loaded is Microsoft base display adapter. I don't know the name of the video card in my computer, but it has a sticker that says "HP part No.: 5188-4289. Anyone know the name of the video card and if there is a driver 64 bit Windows 10 for him.

    Thank you two for your attempts to fix my problem. Unfortunately, the driver makes no difference, so I will need to replace the video card.

    I was completely happy with the way my PC has been implemented with Win7. I am not happy with the problems that caused the upgrade to win10. In addition we have all lost so much time, not to mention the expense.

  • disk memory and space requirment for development database

    Hi all

    I want to know the disk space and memory required for the configuration of the environment development database.

    Production database size is max 25 to 30 concerts
    and only 3 user will use this database

    on this info my suggesion is to go with 3 GB memory 60 GB of backup space and archivelog. Let me know experts comment on that

    xuv500 wrote:

    I want to know the disk space and memory required for the configuration of the environment development database.

    Production database size is max 25 to 30 concerts
    and only 3 user will use this database

    on this info my suggesion is to go with 3 GB memory 60 GB of backup space and archivelog. Let me know experts comment on that

    How long lasts this string? ++

    So, in other words - it depends. Development environment might include a database logic dev (containing data from prod), one database Q & A logic (to test changes in dev) and a complete copy of the prod database logic (to test the final deployment).

    It could contain an R & D environment - where all data from prod is necessary for data mining research and then to deploy processes of extraction of useful data in the production.

    It could be used in a number of ways - and some of them will be more intensive in the transformation and requiring more data, than the production.

    Ideally - dev environment should look like as close as possible to the prod environment. Ideally, that means a server hardware and similar size, same o/s and Oracle versions and same volumes of data.

  • ASA5585-S20-K9 from 8.2 to 8.4 upgrade memory required?

    Have an ASA5585-S20-K9 and I need to get from 8.2 to 8.4.  Currently has 4 GB of memory, but it needs to be improved to a minimum of 8GB.   I searched high and low for a kit to upgrade for the 5585 but do not come with anything.  Found for the 5540 and below, but there must be something special about the 5585 s I can't find anything.

    If anyone has an idea on what I need to get to level set memory, it would be appreciated.

    Chris

    Hello Chris,

    According to usually at the documentation below, we can see that ASA 5585 comes with 12 GB of memory. Please see the 5585-s20 ASA data sheet below.

    http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-serie...

    Firstly, please note if you are running 8.2.x code on your ASA5585-s20. It seems that ASA 5585 SSP-20 will watch 4 GB of RAM which is expected for the 8.2 software with no support for 64-bit (so it cannot process more than 4 GB of RAM in the application of the ASA). If you switch to 8.4 example software, which supports 64-bit, all of the 12 GB of RAM will be used.

    Release notes for 8.4;

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa84/release/notes/as...

    The memory required for the upgrade:

    http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-serie...

    Also on the way to upgrade from 8.2 to 8.4.

    Things to remember: -.

    Upgrade from 8.2 to 8.4 ASA, is NOT a minor update. There are a few things that are need to keep in mind:
    1. NAT statements are completely different.
    2. the IP addresses used in ACL are real IP (not translated)
    3. it is recommended that you take the time to stop for this upgrade.

    Things to do before the update: -.
    > Disable NAT control over the two ASA.
    > Check the memory required for the upgrade.
    > Take configure Backup.
    > Follow the upgrade path as mentioned below.

    Things to do after the update: -.
    > after reclassification of 8.2.x to 8.4.7, you must check the start config error.
    > present the startup-config errors, it will show that NAT and ACLs statement has not been
    migrated, so we can manually configure these instruction.
    > arp permit-nonconnected.
    > Of 8.4.7 9.1.4 or 9.1.5, you can migrate directly.

    Hope this information helps you.

    Kind regards

    JAI Ganesh K

  • How to set the SGA / PGA or memory target for the database

    Hello

    We use on AIX 5.1,6.1, oracle 9i, 10g, 11g

    Currently, we manage the databases on the default memory which was chosen at the time of the creation of the databases.

    Now the application owner want to host multiple databases on the same server, so they ask the

    rough idea on the memory required for each database,

    How we calculate the amount of memory required for each database.

    Thank you

    that recommend the SGA ADVISOR?

  • Error: "no physical memory is available to the location required for the windows boot manager." The system cannot continue. "

    I have a stable system that works with a processor E6300, card mother evga 680i, graphics card 8800gts and 8gbs of RAM running on ulitmate windows 7 (32 bits - I decided to re - install with 64-bit to use the extra 4 GB of RAM, after I deal with the question below).

    I recently tried to add an adapter of Intel RS2WC080 SAS/SATA controller in a PCI express slots on the card mother 680i. I know that the card works (such as "it works very well in another motherboard), but for some reason when I put it in the 680i mobo I get the following message appears when I try to start windows. (i.e. the raid controller has no windows on the disks. I always use original hard drive always connected on the same Sata port on the motherboard)

    "No physical memory is available to the location required for the windows boot manager." The system cannot continue. "

    I tried to turn off virtually everything I could in the bios of the motherboard as an experience (including the things I needed). I also disabled the Intel RS2WC080 card bios.

    I'm puzzled. So what I want to know is simply a hardware compatibility problem, or is there some kind of workaround I can run in windows 7. For example, is there maybe some sort of way for her to start using a different memory location than its currently using? (Or is it something error message related to the memory of the bios that can only be overcome with software?)

    Thanks for any help.

    I tried to disable everything in the bios... including the things I needed. No luck

    Thank you very much for the reply Chris but I don't have abandoned bascially. Right now I guess the card and the 680i have some kind of incompatibility and I will just get a different mobo.

  • Laptop & graphics card required for Adobe Cloud?

    Hi all

    , I'm looking for a new laptop and want to be sure that I buy one with the conditions required for Adobe Cloud.  Is the configuration required for Cloud based on different software (eg. Photoshop, After Effects, Flash, etc.) or are there requirements just to use the Cloud?  I don't know much about computers so I'm having a hard time find one that meets the required conditions.  I would be very happy if someone who already uses clouds of Adobe can provide suggestions.  I'm not an Apple person, currently I'm looking in the following laptops:

    Dell Inspiron 14z:

    3rd generation Intel Core i5 processor

    8 GB memory

    500 GB 5400 RPM SATA HDD and SSD 32 GB mSATA

    AMD Radeon HD7570M 1 GB video card

    Dell Inspiron 14R:

    4th generation Intel Core processor i5-4200U

    8 GB memory

    1 TB SATA hard drive 5400 RPM

    Graphics Intel HD 4400

    Sony Vaio did:

    3rd generation Intel Core i5 processor

    NVIDIA GeForce GT M 740 graphics card (1 GB) hybrid

    750 GB (5400 RPM) hard drive

    8 GB (4 GB x 2) DDR3L - 1600 MHz

    Thanks in advance for any help you can provide!


    Thanks Ashish!  It looks like Microsoft Windows or Mac OS and internect connection is required for the creative cloud desktop app, so I think I have it is not to worry about the system requirements for each program of the meeting?

  • Comply with the requirements for El Capitan if I have a Mac Mini MTN. Lion and 2 GB of memory running with a 2.4 GHz Core 2 Duo?

    Comply with the requirements for El Capitan if I have a Mac Mini MTN. Lion and 2 GB of memory running with a 2.4 GHz Core 2 Duo and 1.07 GHz and 3 MB of L2 Cache bus speed? Recommend - install you more memory and if so, why?

    1. Yes.

    2. Yes. Any newer version of Mac OS X 10.6.8 is likely to be sluggish on only 2 GB of RAM.

    (141471)

  • Card required for control special measures

    Hello!

    We have some NOR-DAQ cards (PCI-6221, 6251 and 6036E) but none of them seem to be capable of the following measure.

    There is a digital pulse train that must be received (practically with a meter). To measure the VOLTAGE to a channel of AI when a pulse is received. The frequency of the pulses can be 1 KHz, therefore generating events at each pulse for the PC is not viable. He must also know where the pulse OCCURRED (something as the card should have its own clock and should be able to put next to the measured voltage value).

    In addition, the map should give a sign of output (pulse change or line) of 1. the number of pulses reached a given amount or 2. the voltage is lower or exceeds a value given to a channel to HAVE. If an automatic output is not available at least we have an event to the PC.

    Will there be any card to fix this? In fact the card must have at least two meters since we have two trains of digital pulses, but only is active to a degree. Thank you very much for your suggestions!

    Could you clarify it please ", we have two trains of digital pulses, but alone is.
    Active to a degree.  You check in for a number of pulses on several lines?  You have more than one channel of Analog Input?

    Without taking into account the requirement for the 2nd train of digital pulses for the moment, to my understanding of the application the 6251 could do you need:

    1. the signal of AI must be connected to the 6251, since it is the only one of the three that supports analog trigger.

    You need to configure an analog reference trigger to allow comparison shipped.  You can use the line to HAVE it if you are sampling just one channel (or an APFI line if you're sampling from multiple channels).  Export event of analog comparison will tell you when the signal is outside a certain threshold (the graph presents 'Entering the window' but you can select "Exit" instead):

    2. connect the Digital pulse train to one of the PFI lines on the 6251.  It will be the sample for your task clock to HAVE.

    4. use the same PFI line as a source for a meter (pulse) output task.  Set the initial delay so that when the desired number of pulses have been counted you will produce a pulse on the output of the counter.

    5. you now have a line telling you what N pulses have been reached (from step 4) and a line telling you where I is outside a window (in step 1).

    6. If you want to timestamp pulses using the edge of the Office counter, you must use the counter 2nd as a county of edge stamped with the external pulse as your sample clock signal.  This will give you a very precise timestamp of your external impulses (compared to the beginning of the task).

    If you need for impulses of timestamp on multiple lines, you can look in the task configuration of change detection of DI on the 6251 and using change detection event as the sample for the task of counter clock.  You must implement logic in SW to determine which line has generated the actual event.

    You have also 4 other counters to play with on your other DAQ hardware two, so depending on what you want to do, you should have a little flexibility.

    Best regards

Maybe you are looking for