Keep the power to the USB port after stopping down?

I would use one of the USB ports to plug in my cell phone to load from one day to the next off the computer. What are the steps to follow to set computer to keep providing power via USB ports after shutting down the computer?  I'm a novice so need to know where to find the place that controls the settings and what to click on. Thank you!

Advertisement

If you put the computer in Standby Mode when you stop, the USB ports are not powered off.

Tags: Windows

Similar Questions

  • Toshiba 46TL938G loses the WLan configuration after stopping down

    Hello

    46TL938G unpacked yesterday, updated the firmware on the Internet.

    Wireless set in place with WPS works, but configuration is lost after turning the TV market / back.
    I can't use assisted because of hidden SSID configuration.

    In manual mode, I always get a bad autorhization information and/or encryption not supported. Access point uses WPA2-PSK AES.

    Is it possible to Setup WPS paste?

    Any news?
    I recommend you try different configuration scenarios:

    -try password that are more than 8 to 10 characters.
    -Try different encryptions: WPE / WPA - PSK / WPA2-PSK (AES, TKIP or AES and TKIP)
    -try to connect with prior authentication ON and OFF
    -try to connect to the WLan using option hidden network - enabled or disabled

  • ProDesk 600 MT: all the usb port disabled after startup Win7

    Hello world

    I just brought a few ProDesk 600 MT after that the installation operating system, one of them seems locked all the usb port after the boot of win7.

    Can I use keyboard and mouse during startup, including the bios or windows safe mode selection menu. However, once started to win7, all usb port are disabled, not even power supply. Which means no keyboard, no mouse. I can't do anything else until the eve of the computer by push and hold button / stop.

    Anyone know why and how to solve this problem?

    Thank you

    Alan

    Hi, Alan:

    See if the news on the thread below solves the problem, if your PC is chipset Skylake.

    http://h30434.www3.HP.com/T5/desktop-operating-systems-and-recovery/can-not-install-Windows-7-on-new-600-G2/m-p/5822964/highlight/true#M130817

  • Satellite M30X powers off the power when you touch the USB port

    Hello everyone, just registered and it is the first problem:
    As there is no general hardware forum, I post my problem here.

    I got it twice, my laptop
    (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

    Motherboard:

    NorthBridge: Intel i855GME
    SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
    Motherboard model: Toshiba EAL20

    USB:

    82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
    Version: 1.0
    Interface: UHCI
    Frequency: 48 MHz

    82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
    Version: 2.0
    Interface: EHCI

    I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

    Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
    There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

    Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
    I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
    Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

    What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
    Still works well. Now for me, that I broke the USB port Insider somehing.
    I could not determine also the loose parts or unfirm at all.

    Y at - it there, diagnostic software that measures the motto of the port or power problems?
    I have a multimeter, fetch short-circuits with it?

    I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

    Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

    Fabian

    Hello

    I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

    > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

    I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

    However, what we can do is to provide some suggestions and assumptions
    It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

  • MP3 player via the USB port (no matter which), it keeps coming back as the "Drive is not accessible. Access is denied. "

    Hello

    So, here are the problems I encounter, and what I did to try to fix myself.
    Whenever I try to connect my MP3 player via the USB port (no matter which), it keeps coming back as the "Drive is not accessible. Access is denied. "  This same thing happens everytime I try to put an SD card in the SD card slot.  However, despite this, I can plug my USB mouse and use it, as well as the keyboard and it records only.  I can also use the HDMI port to use my TV as a second monitor and, also, to record that.
    What I did to solve the problem, it is to restore the system to the previous times before that happened, did not.  I also went into the Device Manager and uninstalled and re installed, USB and SD card drivers.  I also tried something in the sense of taking control of the files via a right click on a folder and go to properties and then security and to the 'advanced settings', the problem with this situation is that I can't in readers at all.
    I am currently running Windows 7 (64 bit) on a laptop Lenovo, the computer itself is actually only a few months.  If someone knows something about this, please let me know.  Thanks in advance.

    Hello

    1. What is the number of brands and models of MP3 player?

    2 are logged in as an administrator on the computer?

    3. are you able to use this device on another computer (not Windows XP)? The MP3 player or SD card already worked on this computer?

    4. Once you get this error message? Do you get this error when accessing the mp3 player and SD card on Windows Explorer?

    Run an antivirus with Microsoft Safety scanner scan and make sure your computer is virus-free.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

    Response with more information to help you.

  • Aspire Switch 10: Keep connect-disconnect keyboard-HARD drive repeatedly while using the usb port

    Hi all
    IAM facing this problem months ago
    It is very disturbing especially iam fan of mouse normal (I hate the touchpad), last week he keeps disconnection/connection too.
    I think that there is a software bug that connect the usb port with usb 3 connecting the keyboard/HDD

    Then
    Please help me.

    update BIOS to the latest version if you have not already:

    http://global-download.Acer.com/GDFiles/BIOS/BIOS/BIOS_Acer_1.08_A_A.zip?acerid=635639807628234039&S...

    Update Firmware on keyboard too if you have not already:

    http://global-download.Acer.com/GDFiles/patch/firmware/Firmware_Acer_D12_W81x86_A.zip?acerid=6355820...

  • After Windows Vista update, the usb port does not recognize the external hard drive

    My external hard drive still worked, but once I have updated Windows Vista USB Port do not see at all. Once I plug it into the laptop (HP Compaq) the port next to the port I plug the also work stoppages which is a usb mouse. Usually, when I have something plugged into the usb ports the laptop would also a sound signal which it does not.

    http://www.bleepingcomputer.com/tutorials/tutorial140.html

    Understand the Extras in Windows Vista and Windows Update info is at the link above.

     

    Remove the Vista updates; two ways to do this:

    1. a System Restore to before the updates:

    Click Start > programs > Accessories > system tools > System Restore > restore time/choose your own date > next

    If you use Norton, disable it before using the system restore.

    If it is impossible to enter the Normal Mode, do a Safe Mode system restore:

    Press F8 at the startup/power and the list of startup options, use THE ARROW key to select Safe mode > and then press ENTER.

    System restore steps according to the info above.

    Also:

    2. click on start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

    > then click the one that you don't want > uninstall will appear at the top > uninstall it.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

    > Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

    When you take a look at pending updates, you can either download/install them one at the time, namely the update causing you problems.

    > or if you do not need an individual > right-click on > UAC prompt > hide it

    See you soon.

    Mick Murphy - Microsoft partner

  • Computer HP laptop, G7-1365dx has no power on the USB ports

    The laptop has no power over but has sense on the usb ports. If I plug a usb powered auto element into a port, it works very well but is not one unpowered. How can I turn on the power to the usb ports?

    If your laptop is still in warranty contact HP total care. To solve this problem, the system board must be replaced.

    It apears that you have inadvertently pointed the USB ports with something that needed too much current.

  • Problem after connecting via the USB port of the printer. Error 0x0000007a

    Recently, I plugged my HP Deskjet2360 printer via the USB port on my HP laptop (running w7 Home premium 32-bit) and can not print at all. When I try to print a test page I get the following message ' operation could not be completed. Error 0x0000007a. Operation failed.

    My usual Setup is to have my printer connected to my desktop (Windows XP Pro). My HP laptop is connected via a wireless connection to my home network, which is also connected to my desktop computer. Of course, this means that I have the office turned on to be able to print from my laptop.

    Everything worked great until I decided I'd rather have my connected printer to directly to my laptop via USB.

    When I connect the printer via the USB port on my laptop, windows installs the software and reported no problems. Yet when I try to print a test page, I get the mentioned error. When I then reconnect the printer to the desktop and try to print a test page to my network, I get exactly the same error message. The office and the printer still work fine, it's just that I can't print from my laptop.

    I uninstalled and reinstalled the printer on my laptop with the USB connection and the network, but it still does not work. The resolution of the problems on the laptop reported no problems, and the printer is set as default printer. I also get an another error msg when I click on the Preferences button in the printer properties: address of the 0x5aeba4f1 function caused a protection fault. (code 0xc0000005 exception) Some or all property pages cannot be displayed.


    The only way I found to get around this is to use windows restore and restore my laptop before the point when I connected the printer via the usb port.

    Any suggestions?

    Hello
     
    This error 0x0000007A describes the data area passed to a system call is too small. ERROR_INSUFFICIENT_BUFFER
    You can try to uninstall and reinstall printer driver and check if that helps.
     
    Here's how you can do:
     
    1. open programs and features by clicking on the Start button, clicking Control Panel, click programs, and then clicking programs and features.
    2. Select a program and then click on uninstall.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
     
    After you have uninstalled the driver to restart the computer, this should install it the appropriate drivers for it. You can also try to download the latest driver from the manufacturers website and install it.
     
     
    Kind regards
    Umesh P - Microsoft Support
  • KDL-42W700B giving power to the USB port in standby mode

    Hello

    My new KDL-42W700B giving the power to the USB ports even mode standby.

    I connected internet USB dongle and when I exit tv, as its getting power internet connectivity continues.

    Called the customer service about cela and they claim that TV sends power to ports USB is the characteristic of the TV and Sony engineers designed this so.

    I've not seen such lame feature anywhere in any model in other brands, but also Sony models too.

    I checked the earthing of the power outlet power. Its perfect.

    Is this a problem with my TV or something else? Please give me the solution

    Thanks in advance

    Bharath

    It does not occur for other models

  • the power cord of the ac for my iphone charger 6 will work in the USB port in the car for the load

    Looking for a car charger for my IPhone 6.  Wondering if the cable operator in the House will work in the USB port on a car?  It hurt my phone.

    Yes you can. As long as you have in the car's USB port. It can load more slowly then wall charger, but it works! I load mine in the car all the time

  • My HP 14 laptop is not recognizing the usb ports and wifi at startup.

    During the last few days I been dealing with the issue that my laptop does not recognize the usb ports and wifi. After several reboots, it works fine. My drivers are up to date, so I don't know why, I'll have this terrible problem.

    Welcome @hildergarn,

    Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you have a problem with your Wi - Fi and USB ports on your laptop from HP.

    My first suggestion would be to use the wireless network troubleshooting and Internet tool. At the bottom it will ask you questions to help you diagnose the problem.

    Please take a look at this great Charter called troubleshooting wireless network and Internet. This document will help you to solve the problem of Wi - Fi.

    Have you tried to restore the BIOS?

    Have you tried to connect directly to the Modem/Router?

    You have uninstalled the driver in Device Manager?

    Please try to uninstall the driver in Device Manager by using the following steps:

    • Go to the Device Manager.
    • Expand network adapters.
    • Right-click on all NICs individually.
    • Click on uninstall.
    • Restart the laptop twice.

    How many devices you try to connect?

    What you are trying to connect via USB?

    Are - what you happened to try to use the HP Support Assistant?

    Here is a link to the HP Support Assistant, if you not him have not yet tried. Simply download and run the application and it will help with the software and drivers on your system that need updated.

    Here are other troubleshooting steps that may help too. If the USB device does not appear in Device Manager, then it might be a question of power requirement. Unplug the machine and perform the following steps until the device is detected:

    • Reboot the laptop
    • Plug in and wait five seconds.

    • If the device does not appear, try connecting to another USB port.

    • If the USB device is displayed in Device Manager after you connect the cable to a different port, then uninstall and reinstall the software of USB device driver.

    If the device is not recognized in any port, unplug it and go to the next step.

    • Open the Device Manager.
    • Double-click Bus USB controllers,

    • Double-click on a USB root hub,

    • Click the Power tab

    • Click on properties of power supply (if it is displayed).

    Devices need that are connected to the hub are shown, as well as the power they have. If the total displayed power is more than 500 mA, remove the devices and use a hub powered.

    • Continue looking at the properties of the power of each USB hub. If the total power required exceeds the total available power for the hub, then remove a device on this hub to a decrease in the number of consumption.

    • Plug in and wait five seconds. If the device is not recognized, unplug and go to the next step.

    Please note; Remove USB cables at high speed that are more than 3 m (9.8 ft) in length and use cables at high speed that are shorter than 3 m.

    Source: troubleshooting USB connections - please look at this document and follow all the steps in it.

    When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you do not want to show your appreciation for my efforts today, please take a second to click the Thumbs Up button below.

    If please re-post and let me know the detailed results of all the troubleshooting steps in this post. Could you please provide me with your model number (How can I find my model number or product number?) also.

    Can't wait to hear from you!

    Have a great day!

  • "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

    "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

    1. my laptop - acer aspire 5030 - has been having this problem for the last five months.

    2. I tried everything including changing service pack, as we have xp professional, he has recently upgraded to vista business 32-bit with service pack 1.

    3 tried all the methods start the laptop after a few hours, remove the battery, press the power button for half a minute, and so on.

    4. I finally he formatted a couple of times, but the problem is not.

    5. later, I improved the professional system of vista and installed the latest security patches, but the problem remains

    6. now, I started to update its drivers, although the device is identified to be connected, but is not recognized. "the error message" not recognized usb device "appears. I try to reinstall the drivers or upgrade of drivers, it does not. It displays the message "the drivers for this device are to this day.

    7. initially, the connection of the device, the drivers are installed but still the device does not show in Explorer.

    8. I tried to change some registry values by merging a regedit file in the registry - for display devices that are not present; but still, it has failed.

    9. I then tried to delete the file infcache1.inf in c:\windows\system32\inf, but the problem persists.

    10. Subsequently, I tried to create another registry entry to "disable selective suspend" in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB by adding DWORD and assigning a binary value of 1.

    11. I tried later also to uninstall all the system devices including USB controllers, drives and the storage controllers, who must still without success.

    12. I tried to see if the drivers in safe mode, which they did not.

    13. I tried to delete the following registry entries =

    HKEY_LOCAL_MACHINES\System\CurrentControlSet\Enum | USB PORT; HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10318 & HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10200.  The computer does not have alow it.

    14. the BIOS indicates device pnp "disabled", which I also look for the BIOS settings, which do not allow me to change to change existing ones.

    15. I have not found the WINDOWS\SYSTEM32\drivers\USBSTOR file. SYS in my driver store. This affects the system?

    16. I also contacted manufacturers pnp devices that provided me with most recent and versions compatible drivers for my devices - namely an apple ipod & Seagate external HARD drive - but even after that the drivers are installed properly and the system rebooted the problem remains. Is this something to do with the updated playing driver registry entries does not after the update? OR is what registry entries are configured to only read the entries at the time of the installation of the OS?

    17. I also contacted local sellers who have suggested to me to change the "motherboard". This will help as a last resort?

    18. in the meantime I had also installed other operating systems to Linux - Fedora and Ubuntu; Full Windows XP - Home & Professional and Vista Edition. All these have been installed successfully but do not solve the problem of usb.

    19. I have also raised the original HARD disk & replaced by another HARD disk. also checked the power of all ihee and ehee usb ports to be at least 5 V. I also disabled the automatic deactivation of devices usb by the system. physical contact, ports and connecting cable is fine. the distribution of power is set at 10% for the ihee ports and 20% for ports ehee, which is what is should be the physical output is also close to 5V for all ports connected.

    20. all professional (hardware or software) should any solution for the problem of the usb ports on my laptop?

    Something that you haven't tried:

    How to fix USB device not recognized in Windows

    http://www.online-tech-tips.com/computer-tips/USB-device-not-recognized/

    I hope I could help

  • U2413, calibration solution Ultrasharp fails to connect to display via the USB port

    Dell U2413 SN: CN-0YCM0F-72872-48P-A81L REV A01 August 2014

    Try to run the ultrasharp Dell V1.5.3 on this monitor calibration solution, however, the software stops and displays "please connect the screen to your computer via a USB cable." I click the OK button after you have checked that the USB port on the computer is connected to the USB connection screen, but ultimately, this message appears:
    "Could not establish a connection to the screen. Please make sure that the USB cable is connected and try again. »

    Has tried this on two different computers, running Windows Pro 8.1. One was connected to the monitor cable HDMI to DVI (Thinkpad 10 via docking station), the other using the provided Dell Display Port printer for (Tablet Thinkpad X 230) mini display port cable.

    The USB ports on computers were connected the Dell supplied USB 3 cable to the monitor. Also tried this on a single computer by using a USB 2 port and a USB cable with the same result. The USB connections on the monitor seems to work ok when you plug a flash drive or the i1 Display Pro. Also, did a reset Monitor USB and verified that Windows has seen additional generic hubs when the USB Monitor is connected to the computer. There are 4 additional hubs when you use additional 2 usb hubs and USB 3 cable when using the USB 2 cable. In addition, power cycled the monitor several times (as recommended in the version that is known for this problem) without success.

    Before the attempt to make the calibration:
    A factory reset on the monitor.
    Ran the monitor self test and SUBMISSION. No problem found.
    Monitor purchased from Dell November 2014

    Same result with V1.5.7

    Any suggestions? Where should I go from here?

    I had success in the U2413 of profiling. I pulled out an old workhorse, a Thinkpad T43
    under Windows XP. Then installed the ultrasharp Dell V1.5.3 calibration solution and all
    updates available from Microsoft, but no other software - nothing of the Dell-supplied with
    the monitor. Used the DVI - connection DVI and USB 3 cable supplied with the monitor. The
    software Profiler has worked well with this configuration. When the program first took to the "Start
    Screen measure"(where the problem occurs already noted) Windows (message status bar)
    has reported that he accessed software Realtek 3.0. So I focused on research at the Realtek
    software on other systems.

    On the Thinkpad 10. There were two 1. "Realtek Card Reader" and 2. «Realtek USB 2.0 Card Reader» I have
    removed both and reinstalled the software Realtek for Dell monitor CD. Insert an SD card and
    a USB in the monitor and both were seen by Windows Explorer. There was also a Realtek USB
    3.0 card reader to showing in Manager devices under USB controllers. Using the connections between the T10 to monitor previously described the Profiler software, then ran normally.

    X 230 - I removed the "Realtek Card Reader" (V6.2.9600.30168) software and tried to start the
    Software Profiler and it does not at the same point as before. Then I installed the Realtek USB 2.0
    Software for the Dell card reader. However, there was still no Realtek USB 3.0 card reader
    display in the Manager of devices under USB controllers. Software Profiler is not like before. I then
    inserted an SD card in the monitor and the "Realtek USB Card Reader 3.0" appeared in the device
    Manager. Software Profiler, then ran normally.

    So now my two systems Windows 8.1 software profiling will not work if the 'Realtek USB 3.0 Card '.
    Reader"is not listed in Device Manager. To do this the software must be installed (for example
    starting from the Dell CD) AND an SD card must be inserted into the SD slot on the monitor. Remove the SD card
    Card and the device disappears and profiling software will not run. Insert an SD card and the
    Software Profiler works normally.

    How can I get the "Realtek USB 3.0 card reader ' to automatically load before running the Profiler software?

  • Aspire One D255E don't look for a printer connected to the USB port

    My D255E an Aspire don't look for a printer connected to the USB port.  I've never used a printer on this computer before.  Windows 7 Starter will support a printer?

    It should be.  Try these steps and results reports:

    When you turn on and connect the printer via USB, shows tasks for animation in the system tray at the right end of the bar, click it and monitor driver installation.  If the pilot goes then printer must print and perhaps scanning of base via the Windows fax and scanning utility.  To find such a piece of utility type its name in the search box.

    If the driver does not load type of devices and printers in the box to start the search, open it, check if printer is already displayed, right-click on it to open the properties, and try to print a Test page. If it does not print right click on printer again to solve problems.

    If the printer is not listed visit Support downloads of the printer Web page to download and install the base driver.  If a wireless printer, you will need the complete package to do it fully implemented.  If you want to be able to scan from the top of the printer to the PC, then you also need the full package.  Keep track of the configuration screens when you install the software.

    If you still have problems after return the exact error with photos if possible.

Maybe you are looking for

  • New update iOS 9.3.2

    After you download the update iOS new 9.3.2 on my iphone5, my phone started to slow down. For example, when I get an email, and I open it, safari is slow downloading photos and/or the site. He arrived not with the previous version.  How can I fix it

  • Satellite C650 - how to connect to HD TV

    Hello I was wondering if it was ok to connect the C650 laptop to HDTV using an AVG for an HDMI cable. It work? concerning

  • Had to wipe the Qosmio F20

    would he have deleted? including the TV? and on the side of the note book? or just the computer side? Windows and drivers, thanks in advance

  • Upgrade the video card and PSU

    Hello I have a HP Pavillion A6642p It contains all the Info material: http://bizsupport1.Austin.HP.com/bizsupport/TechSupport/document.jsp?objectID=c01559154&lang=en&cc=u... I was wondering if I had to update my video card, the size of a power supply

  • How to check my identity?

    Hi, I go the settings-> iCloud-> password and security. I want to change my Security Questions, because I have lost the answers, I would also like to set up an alternate email address. I can't do these things because when I type the Questions of safe


HashFlare