Keyboard typing two different characters at once

Whenever I am typing some characters another character will pop up with him. For example, I try to type 'L' and when I'm not using the screen keyboard it types like '; L '. There are several different keys, that what is happening but this isn't the case with all keys. This just started about 30 minutes ago. I cleaned my keyboard and it started to malfunction about 10 minutes after

Happens to thw sequence of characters that I found

l = ; l

p = po

o = in.

a = select all

and several others

Hi @ML0802,

Welcome to the HP forums! It's a great way to engage, ask questions and find resolutions by working with specialists from the community of HP. I understand that you need help with the keyboard that prints incorrect characters. It'll be a pleasure to help you with this.

You did a great job on diagnose the problem on your side. Kudos to you on this point. We greatly appreciate your relationship with HP. You're an HP customer, and we greatly appreciate you for doing business with HP. I take it as a privilege to share this platform with you.

  • First of all, it looks like a possible hardware problem with the computer. Please perform a hard reset. Steps: Turn off the computer and unplug the charger. Then remove the battery only if it is removable.
  • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
  • Replace the battery and the charger plug it back.
  • Turn off the device. When you turn it upwards, immediately press the F11 key slowly several times.
  • Need you to Recovery Manager. Here, choose the option "troubleshooting." Then, please select 'Advanced Options' and 'command prompt '.
  • Type all of the characters in the keyboard in this mostly black window keys that do not work properly.
  • If F11 no transports you to the Recovery Manager, please keep hit the "ESC" gently several times the moment you turn on the unit. It takes you to the start menu and you could press F11 from there to go to the Recovery Manager. Please check all the keys in the window command prompt black, especially the keys that do not work.

If this does not work in the command line (black window), then it's a hardware with the keyboard problem. For assistance please visit this link: http://support.hp.com/in-en/product/HP-Pavilion-15-Notebook-PC-series/5355006/model/5399238/document/c03738933/

If all the keys type properly without the incorrect characters printing, the issue could possibly be corrected by performing a system restore. Link for the restoration of the system: http://support.hp.com/in-en/document/c03327545

I hope this helps. I would like to know how this happens. I hope the problem is solved without hassle and the unit works very well. I'm always here for you help. Please reach out at any time.

Just to say thank youPlease click the ' Thumbs Up ' button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

Now carefully and have a wonderful week ahead.

Tags: Notebooks

Similar Questions

  • Problems with the keyboard, typing the extra characters

    Original title: Getting irritated by symbols

    When I type a few symbols, such as the double rating mark("), single quote ('), apostrophe (') or CAP (^), these symbols will appear once I get home the next symbol or letter. For example, if I write 'Hello', first double quote appears after I enter the letter H, and the second citation appears after clicking on the comma. And how it works on all programs, where I can write (notebook, desktop, browsers, etc.). Is it possible to change this strange behavior? I am using Windows 7 Ultimate x 64 and wireless keyboard.

    When I type a few symbols, such as the double rating mark("), single quote ('), apostrophe (') or CAP (^), these symbols will appear once I get home the next symbol or letter. For example, if I write 'Hello', first double quote appears after I enter the letter H, and the second citation appears after clicking on the comma. And how it works on all programs, where I can write (notebook, desktop, browsers, etc.). Is it possible to change this strange behavior? I am using Windows 7 Ultimate x 64 and wireless keyboard.

    You use the software keyboard called "United States International." Go to control panel | Region and language and click the keyboards and languages tab. Then click on change keyboard and change in the United States.

  • use two different characters in the same domain

    Hi, how to use for different fonts in the same field?

    unless "crush you" painting: you do not have.
    If you do, you can use graphics.setFont

  • Keyboard model 1. 0a 1027 not type correctly, all keys produce different characters

    Original title model keyboard 1. 0 to 1027. Keyboard not typing correctly, all keys produce different characters? Need your help please.

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    1. Ideas:
    • You have problems with programs. ; Wireless keyboard (model 1027), produced different characters when I type, which none match those of l I'm pressing. He is stuck on a different format? I tried to reset the Control Panel, but nothing helped. Need help from someone who knew the problem and the solution please. Thank you

    Error messages

    • Recent changes to your computer
    • What you have already tried to solve the problem

    Hi rvh6636,

    1. you remember to make changes to the computer before this problem?

    2. did you try to use the keyboard on another computer?

    You can try to check the keyboard on the screen and if the problem persists.
    Check out the link:
    Type without using the keyboard (on-screen keyboard)
    http://Windows.Microsoft.com/en-us/Windows-Vista/type-without-using-the-keyboard-on-screen-keyboard

    You can consult the following KB articles and try the steps and check if that helps:

    Troubleshoot wired keyboards that do not or only the erroneous characters category

    http://support.Microsoft.com/kb/258826

    Troubleshoot the incidents of the response to the mouse or wireless keyboard

    http://support.Microsoft.com/kb/838398

    Hope this information is useful.

    Jeremy K
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • Tecra A9 - keyboard "unlocks" and bad characters are typed

    Keyboard "unlocks" and bad characters are typed using the QWERTY layout. Have tried to change the language options with some success in the short term.

    However changes in languages quickly becomes "unlocked".
    How can I solve this problem?

    Advice please.
    Thanks, Mike

    Hello

    To be honest, I don't know what you're talking about.
    If your keyboard does not match the language of the keyboard, then you should change that and should add new language.

    In this case, you will be able to switch between languages, using SHIFT + ALT shortcuts

    Of course, you can also remove the other languages. In this case, the SHIFT + ALT will not function.

  • Keyboard produces different characters

    When I try to use the x, s, w, or 2 on the keyboard (on laptop Dell Inspiron 1501), it inserts different characters. When I type the w it inserts... s iuop inserts jkl; ------... inserts, Mr. x------... and 2 inserts 8790. It is done just for these 4 keys n, they are little diagnal online. IDK what the problem is... I have tooken the keys and put them on and I changed the language thing and it still does not. Help, please!

    Try safe mode - does the behavior persist?  What if you try a clean boot?  The techniques in the article of boot is a way to try to identify some software that may be responsible for the behavior.  Also try another user account.

    You have an external keyboard, you can try?

  • Why can I get two different results from the same coefficients?

    I get two different results of the evaluation of the polynomial function.

    For the first, I get the coefficients of a polynomial function to adapt.  I feed the coefficients of the function made the function Eval Poly and get the correct 12.8582 result when I evaluate 49940.

    For the second, I create constant array of values that have been returned by the polynomial Fit function (I typed in).  However, I get an incorrect result of - 120.7913 when I feed the constant table the function Eval Poly when I evauate 49940.

    How this can happen when I use the same values in table?

    A picture of what I explained is attached.

    Hi Altran,

    are you sure about using the 'same '?

    You compare them? Do you have (at least) set them to 17 digits display properties?

    Please attach a VI instead of an image...

  • The way of writing to a wireless bridge between two different routers.1:broadband and dir 2:dlink 605 l

    I want to bridge.and wireless I can't do that... Please send me how to write to a wireless bridge between two different routers.

    1:broadband
    and
    2:Dlink dir 605 l,

    Hi Mohammed Ehsan Jourah,.

    Thanks for posting the request in the Microsoft community forums.
    I understand that you need to know how to make a wireless bridge between two different routers

    What version of the operating system is installed on the computer?

    To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

    A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

    You can try the steps at the bridge between two different routers wireless.
    a. determine the coverage area. When using two or more routers, the coverage area should be divided, and each router should be placed in a central location in each subdivision. If you add a wireless router to an existing network, this may mean moving the first router.
    b. decide which router is the main router. The main router is connected to the Internet, a LAN cable or other networks. It should be as close to the wired network connections or who has the best line of sight to another wireless network. In addition, the main router should be a high range router, allowing large tables of State and more users.
    c. buy a spare antenna, as the antennas that come with most routers do not have very good range. Quality omnidirectional antennas can push the range and signal strength of each of the routers, which, in turn, will reduce the cost by allowing routers less cover more space overall.
    d. deploy the primary router carefully. This router is the most important and requires most of the time of installation and options. Set the WEP (Protocol) encryption Service Set Identifier (SSID) and wireless, set up the Internet connection and test the router with some clients (computers). Once you get the main router deployed, deploy other routers should be easy.
    e. deploy the secondary routers, which must be configured to operate in "mode of transition." Secondary routers should be deployed around the perimeter of a large area or 'hot spots' where users placed - for example, will convene a bench Park or the table.

    Links:
    Create a network bridge:
    http://Windows.Microsoft.com/en-us/Windows7/create-a-network-bridge

    Add a connection to a network bridge:
    http://Windows.Microsoft.com/en-us/Windows7/add-a-connection-to-a-network-bridge

    Hope this information helps you. If you need to get help or information with decision-making wireless bridge between two different routers, I'll be happy to help you.

  • Whenever the computer is started, two different styles of start menu appear on the screen, divided vertically from left to right.

    Original title: is this monitor or windows?

    This condition began while I was running xp sp 3.

    I worked in google earth at the time.

    I don't remember exactly what happened.

    But now, every time I start windows, two different styles of the start menu

    appear on the screen, divided vertically from left to right.

    The menu on the right can only be extended to about half of the control panel to the left.

    The menu on the left can grow to the right once the right image has been reduced.

    I tried to reset the start menu in the program settings without success.

    Anyone have any ideas?

    I hope that I was clear enough with this info.

    The article you referred to seems to apply to vista and windows 7.

    How ever, before I received your reply I had already solved the problem myself"

    I appreciate the proposed both help Lisa M and Azeez 'n'

    No further assistance is necessary.

    Thanks again.

  • have two different computers and have problems recoving from hybernation. Locking the system

    Original title: recovery of hybernation

    I have two different computers MS 7 and have all two issues recoving from hybernation. They lock just straight up (do not accept an entry mouse or keyboard) and requir3e hard re boot. Goes 8 to 10 times a week.

    Hello

    (1) did you of recent changes to the computer before the show?

    (2) is the specific question at the opening of specific applications or programs?

    (3) you get an error message?

    You can perform the following methods and check if it helps.

    Method 1: Windows 7 hangs or freezes

    http://support.Microsoft.com/kb/2681286

    2 the resolution of the problems of method Performance

    Run the troubleshooter of performance, then check if it helps.

    Check out the link: http://windows.microsoft.com/en-US/windows7/Open-the-Performance-troubleshooter

    Method3:How to troubleshoot performance problems with sleep, hibernation and resume:

    http://support.Microsoft.com/kb/950686

    Note: The article remains valid for Windows 7 also if it is for Vista.

    For more information, connect to:

    http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions

    Method 4: update video drivers card

    Check if the video card drivers are up to date. Install the latest video card drivers for Windows 7 on the manufacturer's Web site.

    Tips for solving common driver problems:

     http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

    It will be useful.

  • Select Max (Date) in two different tables...

    Dear all,

    I need the date of last update of two different tables, I mean max (date). We will update one table at a time. Updated once I need to take the last update.

    It can be either in table A table B.

    for example.

    Table A

    Date of the ID

    100 16/05/2014

    101 20/05/2014

    102, 22/05/2014

    Table B

    Date of the ID

    100 04/06/2014

    101, 26/05/2014

    102 21/05/2014

    I need the date of table B (101 26/05/2014) last updated date...

    Hello

    Another way, using much more GRAND:

    SELECT LARGER (max1, max2) x

    FROM (SELECT MAX (mydate) max1

    OF mytable_a

    )

    (SELECT MAX (myotherdate) max2

    OF mytable_b

    )

    ;

    Best regards

    Bruno Vroman.

  • Displaying the same Image in two different Image controls

    We use 2 Flex to dynamically display a large image (2 MB +) that is downloaded from an external web server on a different domain. We would like to take that same image, to scale down and post it in along side the version full size of the image in a thumbnail viewer bit that we wrote. This works very well that if I put just the attributes of the source on the two controls Image to the same URL, however, this results in the Image being uploaded twice. Since the image is so large, it is not very desirable behavior.

    Another option that we tried is cloning the bitmapData after one of the images has finished loading and then put back the clone for the second image.

    private void image1Loaded(e:Event): void
    {
    var bmp1:Bitmap = Bitmap (image1.content);
    Image2.source = new Bitmap (bmp1.bitmapData.clone ());
    }

    The problem with this method is that, since the image is downloaded from a server with a different area of our web server, a security sandbox exception is thrown. Because we have no access to this web server, using a crossdomain.xml file is not an option. We looked at the image transmission by proxy through our web server, but given the size of the image, this isn't the best solution either.

    Does anyone know how to do what we try to do without generating a security exception? We don't need to change the image anyway, we just want to display it inside two different Image controls without having to download it twice.

    The image must not be downloaded twice. Flash Player is very picky about it because of the problems you mention. If you download an image from a specific URL and then try to do it again, the image will be have been cached.

    However, if you do this: the image can indeed be charged twice. Why? Because the 2 requests are sent at the same time because no image has been loaded. This translates into the image loaded twice.

    If you have a large image to display, wait for it to load once before the second request. Complete event of the Image will tell you when its bytes have been received.

  • Reports from two different domains

    Hi all

    Is it possible to account for two different subjects areas, i.e., a report that contains fields from two different areas? If so, how could we select fields from two different disciplines in a single report of responses?

    Thank you!!

    One thing to understand is that if you're imagining having two areas (SAs) poster and then by dragging the columns of each in your application without any preparation, then no, that cannot be done. You would need to make a join in the MDB layer and expose the column of the second subject area in the presentation layer.

    But if you indeed interested in UNION (or cross) queries, then do this:

    Build your first application in the first SA in the usual way. Note the number of columns and the data types of each column.

    Now at the bottom of the workspace of criteria, there is a button called "Combined with application similar." Until it clicks.

    Select your second. You will notice that the contours of the columns in your first query appear. This is to remind you that the number of columns in this second query must be the same as in the first. It also shows the data type of each column for the same reason.

    Once you select your columns and your filters, click result. (Oh, you need to decide what kind of combination you want - click the menu drop down.) The result will be a new application that has data from two SAs in the query and combined in the way you select (union, intersection, etc.)

    This should give you a start.

    They are now, some 'useful' or 'correct' points for users on this thread...

  • iTunes playlists show two different formats. Why is it so.

    iTunes playlists show two different formats. Why is it so.

    A playlist displays a blue screen with numbered songs and music before notation box provided for each song. The other playlist is predominently white numbered from each song and check the box. Why is it so and how both can be given.

    Use the view > view as menu from one of six different layouts. Ones you mention is Playlist and songs respectively.

    TT2

  • I have 2 copies of open Firefox (two different windows with lots of tabs), if I reboot can I restore the two sessions?

    I have 2 copies of open Firefox (two different windows with lots of tabs), if I reboot can I restore the two sessions? I am familiar with clicking history / restoration of previous session, but do not want to reboot to let windows update to do it's thing unless I can restore the two sessions.

    guigs2 said

    If they run different profiles, then Yes.

    Thanks, but I use only 1 profile. However, I found the answer! If I restart/turn off / down pc WITHOUT closing a firefox session, he will come with the screen 'well, it's embarrassing"and list the TWO sessions to restore. The trick is not not to close before stopping! If you close them first, then you can only restore the session first (?).

Maybe you are looking for