l2l more unstable fall vpn connection ADSL line
Hello. I have a remote site connection vpn l2l is declining daily (remote site uses pix 501 (6.3), head office use asa 5510 (v7).) The only way I found to restore the connection is to restart the 501. The ISP have diagnosed a faulty line that keeps fall occasionally, but is it not the vpn can automatically reconnect if the line falls for a significant amount of time, which I think is the problem earlier? Thank you.
You have KeepAlive enabled for this tunnel on both ends?
Tags: Cisco Security
Similar Questions
-
RV180 VPN connects and allows you to browse the files, but falls when opening a file.
Last week, we received our 300Mbps fiber connection. We bought the RV180 due to its high performance, and he manages the speed perfectly.
However, when you set up VPN, I encountered a strange problem.
Establishing a QuickVpn or PPTP is simple and connection is no problem. But I'll be fine. I can communicate with QuickVpn or PPTP and find a NAS or PC directory structure, but when I try to open a file the VPC connection drops.
I activate the remote management.
I can ping google.com f-l 1472 without fragmentation, so a WAN MTU of 1500 should be ok.
I have tried disabling attack prevention firewall.I have install the following experience: the firmware update (1.0.2.6), restore the default settings.
Set up the RV180 as follows:
IPv4 WAN (Internet)
------------------------------------------------------------------
Internet connection type: Automatic Configuration - DHCP
DNS Server Source: Get dynamically for ISP
MAC address of the router: use the default address
IPv4 LAN (local area network)
------------------------------------------------------------------
Host name: RV180
IP address: 192.168.75.1
Subnet mask: 255.255.255.0
Mode DHCP: DHCP Server
Domain name: LCDVT
From the IP address: 192.168.75.100
End IP address: 192.168.75.254
Rental time: 24
DNS Proxy: enable
Preventing attacks
------------------------------------------------------------------
WAN (Internet) security controls
Meet Ping on WAN (Internet): disabled
Stealth mode: disabled
Floods: disabled
LAN (local area network) security controls
Block UDP Flood: disabled
Parameters of the ICSA
Block the anonymous ICMP Messages: disabled
Block fragmented packets: disabled
Block multicast packets: disabled
VPN users
------------------------------------------------------------------
PPTP server: enabled
From the IP address: 192.168.75.50
End IP address: 192.168.75.99
Table setting VPN Client:
---------------------------
No: 1
Enabled: enabled
Username: lcdvt
Password: *.
Allow the user to change the password: NA
Protocol: PPTP
Web access
------------------------------------------------------------------
Access on the LAN of HTTPS Web Interface: enabled
Remote management: enabled
Type of access: IP range
Start of range: 192.168.75.1
End of series: 192.168.75.254
Port number: 443
Remote SNMP: disabled
The rest of the menu options are, except for logging policies where I have everything turned on by default.
In this experiment, I connect from a remote location, start navigating among directories of the drive without any problems and then open a file, after which the VPN connection falls (or some process breaks down). After the transfer of a few 100 KB blocks the VPN connection.
Error logs
------------------------------------------------------------------
Thu Mar 20 00:39:18 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45
Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46
Thu Mar 20 00:39:25 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1
Thu Mar 20 00:39:32 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId
Thu Mar 20 00:40:58 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45
Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46
Thu Mar 20 00:41:10 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1
Thu Mar 20 00:41:19 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId
Warning logs
------------------------------------------------------------------
Thu Mar 20 00:39:13 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases
Thu Mar 20 00:40:54 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases
Sat 1 Jan 01:02:43 2011 (GMT + 0100) [rv180] [Kernel] [KERNEL] [23.090000] /home/aruns/rv180w/updated_dec19_final/beta-v1/rv180w-common/comps/gpl/ipset/src/ipset/kernel/ip_set.c: ip_set_create: no type set 'nethash', 'setPublicNet' has not created value
What I am doing wrong? Or the device?
I am interested in what the solution to these problems. Research on get a rv180...
First car of Huntsville and bike e-magazine: www.huntsvillecarscene.com
-
SSL VPN 25 user license - impossible to get more than 2 SSL VPN connections
Hello
I just installed a user license user Premium 25 for SSL VPN on my Cisco ASA5505. Even though it states that the license is installed I get still only two client Anyconnect SSL VPN connections and the third fails systematically. What Miss me?
Thanks for posting to the forum and that the problem has been resolved, and what caused the problem and what has been done to solve the problem. It's the most useful forum when people can read on a problem and can also read what the problem turned out to be and what was done to solve the problem, I think that it is also a good example to remind us that sometimes, the problem is not in our configuration, or even in the area that we administer. So sometimes we have to look beyond our normal home to find the source of the problem.
The question mark it resolved makes it even more obvious to readers that they will find a solution to the problem. So thank you to mark the issue as resolved.
HTH
Rick
-
Hi all
I have a strange problem, trying to establish a VPN between my camera (1941) and a distance of ASA.
The question is, can I say is that the IKE phase precipitates after MM6. I'm not an expert in the present, but I'll try to explain to the best of my knowledge
Here's a cry full debugging isakmp:* 05:12:05.187 Jun 10: ISAKMP: (1001): serving SA., his is 3AD3BE6C, delme is 3AD3BE6C* Jun 10 05:12:05.259: ISAKMP: (0): profile of THE request is (NULL)* 05:12:05.259 Jun 10: ISAKMP: created a struct peer 41.223.4.83, peer port 500* 05:12:05.259 Jun 10: ISAKMP: new created position = 0x4B475724 peer_handle = 0 x 80000004* 05:12:05.259 Jun 10: ISAKMP: lock struct 0x4B475724, refcount 1 to peer isakmp_initiator* 05:12:05.259 Jun 10: ISAKMP: 500 local port, remote port 500* 05:12:05.263 Jun 10: ISAKMP: set new node 0 to QM_IDLE* 05:12:05.263 Jun 10: ISAKMP: find a dup her to the tree during the isadb_insert his 3AD3BE6C = call BVA* 05:12:05.263 Jun 10: ISAKMP: (0): cannot start aggressive mode, try the main mode.* 05:12:05.263 Jun 10: ISAKMP: (0): pair found pre-shared key matching 41.223.4.83* Jun 10 05:12:05.263: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID* Jun 10 05:12:05.263: ISAKMP: (0): built the seller-07 ID NAT - t* Jun 10 05:12:05.263: ISAKMP: (0): built of NAT - T of the seller-03 ID* Jun 10 05:12:05.263: ISAKMP: (0): built the seller-02 ID NAT - t* 05:12:05.263 Jun 10: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM* 05:12:05.263 Jun 10: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1* Jun 10 05:12:05.263: ISAKMP: (0): Beginner Main Mode Exchange* Jun 10 05:12:05.263: ISAKMP: (0): lot of 41.223.4.83 sending my_port 500 peer_port 500 (I) MM_NO_STATE* 05:12:05.263 Jun 10: ISAKMP: (0): sending a packet IPv4 IKE.* 05:12:05.475 Jun 10: ISAKMP (0): received 41.223.4.83 packet dport 500 sport Global 500 (I) MM_NO_STATE* 05:12:05.475 Jun 10: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH* 05:12:05.475 Jun 10: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_I_MM2* Jun 10 05:12:05.475: ISAKMP: (0): treatment ITS payload. Message ID = 0* Jun 10 05:12:05.475: ISAKMP: (0): load useful vendor id of treatment* Jun 10 05:12:05.475: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69* 05:12:05.475 Jun 10: ISAKMP (0): provider ID is NAT - T RFC 3947* Jun 10 05:12:05.475: ISAKMP: (0): load useful vendor id of treatment* Jun 10 05:12:05.475: ISAKMP: (0): IKE frag vendor processing id payload* 05:12:05.475 Jun 10: ISAKMP: (0): IKE Fragmentation support not enabled* 05:12:05.475 Jun 10: ISAKMP: (0): pair found pre-shared key matching 41.223.4.83* Jun 10 05:12:05.475: ISAKMP: (0): pre-shared key local found* 05:12:05.475 Jun 10: ISAKMP: analysis of the profiles for xauth...* 05:12:05.475 Jun 10: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 1* 05:12:05.475 Jun 10: ISAKMP: AES - CBC encryption* 05:12:05.475 Jun 10: ISAKMP: keylength 256* 05:12:05.475 Jun 10: ISAKMP: SHA hash* 05:12:05.475 Jun 10: ISAKMP: group by default 2* 05:12:05.475 Jun 10: ISAKMP: pre-shared key auth* 05:12:05.475 Jun 10: ISAKMP: type of life in seconds* 05:12:05.475 Jun 10: ISAKMP: life (basic) of 28800* 05:12:05.475 Jun 10: ISAKMP: (0): atts are acceptable* 05:12:05.475 Jun 10: ISAKMP: (0): Acceptable atts: real life: 0* 05:12:05.475 Jun 10: ISAKMP: (0): Acceptable atts:life: 0* 05:12:05.475 Jun 10: ISAKMP: (0): base life_in_seconds:28800* 05:12:05.475 Jun 10: ISAKMP: (0): return real life: 28800* 05:12:05.475 Jun 10: ISAKMP: (0): timer life Started: 28800.* Jun 10 05:12:05.511: ISAKMP: (0): load useful vendor id of treatment* Jun 10 05:12:05.511: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69* 05:12:05.511 Jun 10: ISAKMP (0): provider ID is NAT - T RFC 3947* Jun 10 05:12:05.511: ISAKMP: (0): load useful vendor id of treatment* Jun 10 05:12:05.511: ISAKMP: (0): IKE frag vendor processing id payload* 05:12:05.511 Jun 10: ISAKMP: (0): IKE Fragmentation support not enabled* 05:12:05.511 Jun 10: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE* 05:12:05.511 Jun 10: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM2* Jun 10 05:12:05.511: ISAKMP: (0): lot of 41.223.4.83 sending my_port 500 peer_port 500 (I) MM_SA_SETUP* 05:12:05.511 Jun 10: ISAKMP: (0): sending a packet IPv4 IKE.* 05:12:05.511 Jun 10: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE* 05:12:05.511 Jun 10: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM3* 05:12:05.727 Jun 10: ISAKMP (0): received 41.223.4.83 packet dport 500 sport Global 500 (I) MM_SA_SETUP* 05:12:05.727 Jun 10: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH* 05:12:05.727 Jun 10: ISAKMP: (0): former State = new State IKE_I_MM3 = IKE_I_MM4* Jun 10 05:12:05.727: ISAKMP: (0): processing KE payload. Message ID = 0* Jun 10 05:12:05.759: ISAKMP: (0): processing NONCE payload. Message ID = 0* 05:12:05.759 Jun 10: ISAKMP: (0): pair found pre-shared key matching 41.223.4.83* Jun 10 05:12:05.759: ISAKMP: (1003): load useful vendor id of treatment* Jun 10 05:12:05.759: ISAKMP: (1003): provider ID is the unit* Jun 10 05:12:05.759: ISAKMP: (1003): load useful vendor id of treatment* Jun 10 05:12:05.759: ISAKMP: (1003): provider ID seems the unit/DPD but major incompatibility of 104* Jun 10 05:12:05.759: ISAKMP: (1003): provider ID is XAUTH* Jun 10 05:12:05.759: ISAKMP: (1003): load useful vendor id of treatment* Jun 10 05:12:05.763: ISAKMP: (1003): addressing another box of IOS!* Jun 10 05:12:05.763: ISAKMP: (1003): load useful vendor id of treatment* 05:12:05.763 Jun 10: ISAKMP: (1003): vendor ID seems the unit/DPD but hash mismatch* 05:12:05.763 Jun 10: ISAKMP: receives the payload type 20* 05:12:05.763 Jun 10: ISAKMP (1003): sound not hash no match - this node outside NAT* 05:12:05.763 Jun 10: ISAKMP: receives the payload type 20* 05:12:05.763 Jun 10: ISAKMP (1003): No. NAT found for oneself or peer* 05:12:05.763 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE* 05:12:05.763 Jun 10: ISAKMP: (1003): former State = new State IKE_I_MM4 = IKE_I_MM4* 05:12:05.763 Jun 10: ISAKMP: (1003): send initial contact* 05:12:05.763 Jun 10: ISAKMP: (1003): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication* 05:12:05.763 Jun 10: ISAKMP (1003): payload IDnext payload: 8type: 1address: 82.117.193.82Protocol: 17Port: 500Length: 12* 05:12:05.763 Jun 10: ISAKMP: (1003): the total payload length: 12* Jun 10 05:12:05.763: ISAKMP: (1003): lot of 41.223.4.83 sending my_port 500 peer_port 500 (I) MM_KEY_EXCH* 05:12:05.763 Jun 10: ISAKMP: (1003): sending a packet IPv4 IKE.* 05:12:05.763 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE* 05:12:05.763 Jun 10: ISAKMP: (1003): former State = new State IKE_I_MM4 = IKE_I_MM5* 05:12:05.975 Jun 10: ISAKMP (1003): received 41.223.4.83 packet dport 500 sport Global 500 (I) MM_KEY_EXCH* Jun 10 05:12:05.975: ISAKMP: (1003): payload ID for treatment. Message ID = 0* 05:12:05.975 Jun 10: ISAKMP (1003): payload IDnext payload: 8type: 1address: 41.223.4.83Protocol: 17Port: 0Length: 12* Jun 10 05:12:05.975: ISAKMP: (0): peer games * no * profiles* Jun 10 05:12:05.975: ISAKMP: (1003): HASH payload processing. Message ID = 0* 05:12:05.975 Jun 10: ISAKMP: received payload type 17* 05:12:05.979 Jun 10: ISAKMP: (1003): SA authentication status:authenticated* 05:12:05.979 Jun 10: ISAKMP: (1003): SA has been authenticated with 41.223.4.83* 05:12:05.979 Jun 10: ISAKMP: try to insert a 82.117.193.82/41.223.4.83/500/peer and inserted 4 B 475724 successfully.* 05:12:05.979 Jun 10: ISAKMP: (1003): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH* 05:12:05.979 Jun 10: ISAKMP: (1003): former State = new State IKE_I_MM5 = IKE_I_MM6* 05:12:05.979 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE* 05:12:05.979 Jun 10: ISAKMP: (1003): former State = new State IKE_I_MM6 = IKE_I_MM6* 05:12:05.979 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE* 05:12:05.979 Jun 10: ISAKMP: (1003): former State = new State IKE_I_MM6 = IKE_P1_COMPLETE* 05:12:05.979 Jun 10: ISAKMP: (1003): start Quick Mode Exchange, M - ID 2434392874* 05:12:05.979 Jun 10: ISAKMP: (1003): initiator QM gets spi* Jun 10 05:12:05.979: ISAKMP: (1003): lot of 41.223.4.83 sending my_port 500 peer_port 500 (I) QM_IDLE* 05:12:05.979 Jun 10: ISAKMP: (1003): sending a packet IPv4 IKE.* 05:12:05.979 Jun 10: ISAKMP: (1003): entrance, node 2434392874 = IKE_MESG_INTERNAL, IKE_INIT_QM* 05:12:05.979 Jun 10: ISAKMP: (1003): former State = new State IKE_QM_READY = IKE_QM_I_QM1* 05:12:05.979 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE* 05:12:05.979 Jun 10: ISAKMP: (1003): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE* 05:12:06.195 Jun 10: ISAKMP (1003): received 41.223.4.83 packet dport 500 sport Global 500 (I) QM_IDLE* 05:12:06.195 Jun 10: ISAKMP: node set 169965215 to QM_IDLE* Jun 10 05:12:06.195: ISAKMP: (1003): HASH payload processing. Message ID = 169965215* Jun 10 05:12:06.195: ISAKMP: (1003): treatment protocol NOTIFIER PROPOSAL_NOT_CHOSEN 30, message ID SPI = 169965215, a = 0x3AD3BE6C* 05:12:06.199 Jun 10: ISAKMP: (1003): error suppression node 169965215 FALSE reason 'informational (en) State 1.* 05:12:06.199 Jun 10: ISAKMP: (1003): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY* 05:12:06.199 Jun 10: ISAKMP: (1003): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE* 05:12:06.199 Jun 10: ISAKMP (1003): received 41.223.4.83 packet dport 500 sport Global 500 (I) QM_IDLE* 05:12:06.199 Jun 10: ISAKMP: node set 1149953416 to QM_IDLE* Jun 10 05:12:06.199: ISAKMP: (1003): HASH payload processing. Message ID = 1149953416* Jun 10 05:12:06.199: ISAKMP: (1003): treatment of payload to DELETE. Message ID = 1149953416* 05:12:06.199 Jun 10: ISAKMP: (1003): peer does not paranoid KeepAlive.* 05:12:06.199 Jun 10: ISAKMP: (1003): removal of HIS State "No reason" why (I) QM_IDLE (post 41.223.4.83)* 05:12:06.199 Jun 10: ISAKMP: (1003): error suppression node 1149953416 FALSE reason 'informational (en) State 1.* 05:12:06.199 Jun 10: ISAKMP: node set 613686650 to QM_IDLE* Jun 10 05:12:06.199: ISAKMP: (1003): lot of 41.223.4.83 sending my_port 500 peer_port 500 (I) QM_IDLE* 05:12:06.199 Jun 10: ISAKMP: (1003): sending a packet IPv4 IKE.* 05:12:06.199 Jun 10: ISAKMP: (1003): purge the node 613686650* 05:12:06.199 Jun 10: ISAKMP: (1003): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL* 05:12:06.199 Jun 10: ISAKMP: (1003): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA* 05:12:06.199 Jun 10: ISAKMP: (1003): removal of HIS State "No reason" why (I) QM_IDLE (post 41.223.4.83)* 05:12:06.199 Jun 10: ISAKMP: Unlocking counterpart struct 0x4B475724 for isadb_mark_sa_deleted(), count 0* 05:12:06.199 Jun 10: ISAKMP: delete peer node by peer_reap for 41.223.4.83: 4 B 475724* 05:12:06.203 Jun 10: ISAKMP: (1003): node-1860574422 error suppression FALSE reason 'IKE deleted.* 05:12:06.203 Jun 10: ISAKMP: (1003): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH* 05:12:06.203 Jun 10: ISAKMP: (1003): former State = new State IKE_DEST_SA = IKE_DEST_SA* 05:12:25.187 Jun 10: ISAKMP: (1002): purge the node 1140237073Installed IOS is c1900-universalk9-mz. Spa. 154 - 3.M5.bin
Before that, I had 15.3, same thing.
BGPR1 # running shoBuilding configuration...Current configuration: 5339 bytes!! Last configuration change at 05:19:14 UTC Friday, June 10, 2016 by boris!version 15.4horodateurs service debug datetime msecLog service timestamps datetime msecencryption password service!hostname BGPR1!boot-start-markerstart the system flash0:c1900 - universalk9-mz. Spa. 154 - 3.M5.binboot-end-marker!!logging buffered 51200 warnings!No aaa new-model!!!!!!!!!!!!!!IP flow-cache timeout active 1IP cefNo ipv6 cef!Authenticated MultiLink bundle-name Panel!CTS verbose logging!Crypto pki trustpoint TP-self-signed-enrollment selfsignedname of the object cn = IOS-Self-signed-certificate-revocation checking norsakeypair TP-self-signed-3992366821!!chain pki crypto TP-self-signed certificates.certificate self-signed 01quit smokingudi pid CISCO1941/K9 sn CF license!!usernameusername!redundancy!!!No crypto ikev2 does diagnosis error!!!!crypto ISAKMP policy 1BA aes 256preshared authenticationGroup 2lifetime 28800isakmp encryption key * address 41.223.4.83!!Crypto ipsec transform-set Meridian ah-sha-hmac esp - aes 256tunnel mode!!!Meridian 10 map ipsec-isakmp cryptoVODACOM VPN descriptiondefined by peer 41.223.4.8386400 seconds, life of security association setthe transform-set Meridian valuematch address 100!!!!!the Embedded-Service-Engine0/0 interfaceno ip addressShutdown!interface GigabitEthernet0/0Description peer na TelekomIP 79.101.96.6 255.255.255.252penetration of the IP streamstream IP outputautomatic duplexautomatic speedNo cdp enable!interface GigabitEthernet0/1Description peer na SBBIP 82.117.193.82 255.255.255.252penetration of the IP streamstream IP outputautomatic duplexautomatic speedNo cdp enableMeridian of the crypto map!interface FastEthernet0/0/0no ip address!interface FastEthernet0/0/1no ip addressinterface FastEthernet0/0/2no ip address!interface FastEthernet0/0/3switchport access vlan 103no ip address!interface Vlan1IP 37.18.184.1 255.255.255.0penetration of the IP streamstream IP output!interface Vlan103IP 10.10.10.1 255.255.255.0!router bgp 198370The log-neighbor BGP-changes37.18.184.0 netmask 255.255.255.010.10.10.2 neighbor remote - as 201047map of route-neighbor T-OUT 10.10.10.2 outneighbour 79.101.96.5 distance - 8400neighbor 79.101.96.5 fall-overneighbor 79.101.96.5 LOCALPREF route map in79.101.96.5 T-OUT out neighbor-route mapneighbour 82.117.193.81 distance - as 31042neighbor 82.117.193.81 fall-overneighbor 82.117.193.81 route LocalOnly outside map!IP forward-Protocol ND!IP as path access list 10 permit ^ $IP as path access list 20 permits ^ $ 31042no ip address of the http serverlocal IP http authenticationno ip http secure serverIP http timeout policy slowed down 60 life 86400 request 10000IP flow-export Vlan1 sourcepeer of IP flow-export version 5 - as37.18.184.8 IP flow-export destination 2055!IP route 37.18.184.0 255.255.255.0 Null0IP route 104.28.15.63 255.255.255.255 79.101.96.5IP route 217.26.67.79 255.255.255.255 79.101.96.5!!IP-list of prefixes Filter_IN_Telekom seq 10 permit 0.0.0.0/0!T-OUT route map permit 10match 10 way!route allowed LOCALPREF 10 mapset local preference 90!SBBOnly allowed 10 route map20 as path game!LocalOnly allowed 10 route mapmatch 10 way!!m3r1d1an RO SNMP-server communityServer SNMP ifindex persistaccess-list 100 permit ip host 37.18.184.4 41.217.203.234access-list 100 permit ip host 37.18.184.169 41.217.203.234!control plan!!!Line con 0Synchronous recordinglocal connectionline to 0line 2no activation-characterNo execpreferred no transporttransport output pad rlogin lapb - your MOP v120 udptn ssh telnetStopBits 1line vty 0 4privilege level 15local connectionentry ssh transportline vty 5 15privilege level 15local connectionentry ssh transport!Scheduler allocate 20000 1000!endBGPR1 #.BGPR1 #sho cry isa his
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
41.223.4.83 82.117.193.82 MM_NO_STATE 1106 ACTIVE (deleted)
41.223.4.83 82.117.193.82 MM_NO_STATE 1105 ACTIVE (deleted)
For "sho cry ipsec his" I get only a lot of mistakes to send.
For the other end, I had all the settings, I have no access to this device, they insist that this is a simple installation and that any problem is on my side.
I tried to juggle the order of the access list, life card crypto security association and all "googlable" solutions, that I could find.
Any input appreciated.
Corresponds to the phase 2 double-checking on the SAA, including PFS.
crypto ipsec transform-set meridian ah-sha-hmac esp-aes 256 mode tunnel
-
VPN connection with external modem
Cisco 2651XM router
using a wic adsl card I was able to establish a vpn connection from a computer on to my 2651xm router cisco vpn client successfully, but I can't get a connection using an external modem.
My local network at the end of the vpn server is on 172.16.1.xx and goes into the router on f0/0, which stood at 172.16.1.30.
Port f0/1 is 192.168.1.100 and goes to an external modem set as default gateway
192.169.1.254. with this configuration I can surf the internet on the computers in the lan at the server end.
Problem is that I can't get a connection from a remote machine VPN connect. It worked when I used the wic adsl connection, but then I used only
the port of f0/0 that was connected to my local network. But now I'm including the f0/1 port to connect to an external modem, vpn client cannot connect. The cisco vpn client tries to connect by using tcp on port 10000 and I have to configure it in the modem, but do not know if I did it correctly. I tried to transmit the port both 192.168.1.100 (f0/1) and 172.16.1.30 (f0/0), but neither will not work. My config running is attached. Thanks for the pointers.
----------------------
#show running-config router
Building configuration...
Current configuration: 2757 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
vpn hostname
!
boot-start-marker
boot-end-marker
!
no set record in buffered memory
no console logging
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
activate the password xxxxxxxxxxx
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login sdm_vpn_xauth_ml_1 local
AAA authentication login sdm_vpn_xauth_ml_2 local
AAA authorization sdm_vpn_group_ml_1 LAN
AAA authorization sdm_vpn_group_ml_2 LAN
!
AAA - the id of the joint session
!
resources policy
!
no location network-clock-participate 1
No network-clock-participate wic 0
IP cef
!
!
!
!
name-server IP 192.168.1.254
name-server IP 192.168.1.255
IP ddns update method sdm_ddns1
DDNS both
!
!
!
!
!
username secret xxxxxxxxxxx 5 xxxxxxxxxxxxxxxxxxxxxxxxxx
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group workgroup
vpnkey key
pool SDM_POOL_2
ISAKMP crypto sdm-ike-profile-1 profile
match of group identity working group
client authentication list sdm_vpn_xauth_ml_2
ISAKMP authorization list sdm_vpn_group_ml_2
client configuration address respond
virtual-model 2
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
!
Profile of crypto ipsec SDM_Profile1
game of transformation-ESP-3DES-SHA1
isakmp-profile sdm-ike-profile-1 game
!
!
!
!
!
ATM0/0 interface
no ip address
Shutdown
No atm ilmi-keepalive
DSL-automatic operation mode
!
interface FastEthernet0/0
IP 172.16.1.30 255.255.0.0
IP nat inside
IP virtual-reassembly
automatic speed
Half duplex
No mop enabled
!
interface FastEthernet0/1
Description $ETH - WAN$
updated client dns IP dhcp-server no
IP ddns update hostname vpn.vpn
IP ddns update sdm_ddns1
dhcp customer_id FastEthernet0/1 IP address
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
!
tunnel type of interface virtual-Template2
IP unnumbered FastEthernet0/1
ipv4 ipsec tunnel mode
Tunnel SDM_Profile1 ipsec protection profile
!
router RIP
version 2
network 172.16.0.0
network 192.168.1.0
No Auto-resume
!
local IP 192.168.1.110 SDM_POOL_1 pool 192.168.1.120
local IP SDM_POOL_2 172.16.1.21 pool 172.16.1.29
!
!
IP http server
no ip http secure server
IP nat inside source list 3 interface FastEthernet0/1 overload
!
Remark SDM_ACL category of access list 1 = 2
access-list 1 permit 172.16.0.0 0.0.255.255
Note access-list 2 = 2 SDM_ACL category
access-list 2 allow to 192.168.1.0 0.0.0.255
Remark SDM_ACL category from the list to access 3 = 2
access-list 3 permit 172.16.0.0 0.0.255.255
!
!
!
!
control plan
!
!
!
!
Line con 0
line to 0
line vty 0 4
password: xxxxxxxx
!
!
end
Hello
On the ADSL Modem, you must before 500, port 4500 UDP and 10,000 to the IP address of the router.
Basically, tell you the Modem to 192.168.1.100 transmitting any packet received on 192.169.1.254.
On the client VPN choose encapsulation UDP NAT, make use of NAT - T standard.
Please rate if this helped.
Kind regards
Daniel
-
Hello
I have pix 515E and I configured a VPN on it. My users connect to my network from the internet via the Cisco VPN client.
I have problem, only their LAN machine can do VPN from Cisco VPN client to my network at once.
Users are connected to the internet via an ADSL router and the LAN switch.
--------------------------------------------------
PIX Config:
6.3 (4) version PIX
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx encrypted passwd
hostname ABCDEFGH
ABCD.com domain name
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
inside_out to the list of allowed access nat0_acl ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside xxx.xxx.xxx.xxx 255.255.255.0
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool vpnpool 192.168.2.1 - 192.168.2.254
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 0-list of access inside_out-nat0_acl
NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server RADIUS (inside) host ABCDE timeout 10
AAA-server local LOCAL Protocol
RADIUS protocol radius AAA-server
Radius max-failed-attempts 3 AAA-server
AAA-radius deadtime 10 Server
RADIUS protocol AAA-server partnerauth
AAA-server partnerauth max-failed-attempts 3
AAA-server deadtime 10 partnerauth
partnerauth AAA-server (host ABCDEFG myvpn1 timeout 10 Interior)
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
card crypto client outside_map of authentication partnerauth
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address 0.0.0.0 netmask 0.0.0.0
ISAKMP identity address
part of pre authentication ISAKMP policy 8
ISAKMP strategy 8 3des encryption
ISAKMP strategy 8 md5 hash
8 2 ISAKMP policy group
ISAKMP life duration strategy 8 the 86400
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup myvpn address vpnpool pool
vpngroup myvpn ABCDE dns server
vpngroup myvpn by default-field ABCD.com
splitting myvpn vpngroup split tunnel
vpngroup idle 1800 myvpn-time
vpngroup myvpn password *.
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.1.200 - 192.168.1.254 inside
dhcpd dns ABCDE
dhcpd lease 3600
dhcpd ping_timeout 750
field of dhcpd ABCD.com
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
--------------------------------------------------
Thanks in advance.
-Amit
Try to add the "isakmp nat-traversal" command to your PIX. I suspect what happens is that Remote LAN users is translated to a single IP address as they pass through the DSL connection. I also assume that the machine doing the translation has a capacity of IPSec passthrough. Linksys routers would be a good example of this type of NAT device that allows IPSec pull-out.
If that's the case, that a single VPN connection will be able to operate both. The above command will turn PIX detect clients that are located behind a NAT device, and then try to configure the VPN sessions in UDP packets and so to work around the limitation of NAT and IPSec passthrough device.
-
IPSec VPN: connected to the VPN but cannot access resources
Hello
I configured a VPN IPSec on two ISP with IP SLA configured, there is a redundancy on the VPN so that if address main is it connect to the VPN backup.
QUESTIONS
-Connect to the primary address and I can access resources
-backup address to connect but can not access resources for example servers
I want a way to connect to backup and access on my servers resources. Please help look in the config below
configuration below:
interface GigabitEthernet0/0
LAN description
nameif inside
security-level 100
IP 192.168.202.100 255.255.255.0
!
interface GigabitEthernet0/1
Description CONNECTION_TO_DOPC
nameif outside
security-level 0
IP address 2.2.2.2 255.255.255.248
!
interface GigabitEthernet0/2
Description CONNECTION_TO_COBRANET
nameif backup
security-level 0
IP 3.3.3.3 255.255.255.240
!
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa831 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone WAT 1
DNS domain-lookup outside
DNS server-group DefaultDNS
Name-Server 4.2.2.2
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of object obj-200
192.168.200.0 subnet 255.255.255.0
Description LAN_200
network of object obj-202
192.168.202.0 subnet 255.255.255.0
Description LAN_202
network of the NETWORK_OBJ_192.168.30.0_25 object
subnet 192.168.30.0 255.255.255.128
network of the RDP_12 object
Home 192.168.202.12
Web server description
service object RDP
source eq 3389 destination eq 3389 tcp service
network obj012 object
Home 192.168.202.12
the Backup-PAT object network
192.168.202.0 subnet 255.255.255.0
NETWORK LAN UBA description
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
network-object object obj-200
network-object object obj-202
access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any
access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any
OUTSIDE_IN list extended access permit icmp any any idle state
OUTSIDE_IN list extended access permit tcp any object obj012 eq inactive 3389
gbnltunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnltunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0
BACKUP_IN list extended access permit icmp any any idle state
access extensive list ip 196.216.144.0 encrypt_acl allow 255.255.255.192 192.168.202.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
Backup2 MTU 1500
local pool GBNLVPNPOOL 192.168.30.0 - 192.168.30.100 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any backup
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static static source NETWORK_OBJ_192.168.30.0_25 destination DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.30.0_25
NAT (inside, outside) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.30.0_25 NETWORK_OBJ_192.168.30.0_25 non-proxy-arp-search of route static destination
!
network of object obj-200
NAT dynamic interface (indoor, outdoor)
network of object obj-202
dynamic NAT (all, outside) interface
network obj012 object
NAT (inside, outside) interface static service tcp 3389 3389
the Backup-PAT object network
dynamic NAT interface (inside, backup)
!
NAT source auto after (indoor, outdoor) dynamic one interface
Access-group interface inside INSIDE_OUT
Access-group OUTSIDE_IN in interface outside
Access-group BACKUP_IN in the backup of the interface
Route outside 0.0.0.0 0.0.0.0 2.2.2.2 1 followed by 100
Backup route 0.0.0.0 0.0.0.0 3.3.3.3 254
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
value of the URL-list GBNL-SERVERS
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
http server enable 441
http 192.168.200.0 255.255.255.0 inside
http 192.168.202.0 255.255.255.0 inside
http 192.168.2.0 255.255.255.0 inside
http 192.168.30.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 backup
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
ALS 10 monitor
type echo protocol ipIcmpEcho 31.13.72.1 interface outside
NUM-package of 5
Timeout 3000
frequency 5
Annex monitor SLA 10 life never start-time now
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto IPSec_map 10 corresponds to the address encrypt_acl
card crypto IPSec_map 10 set peer 196.216.144.1
card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
ipsec_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
ipsec_map interface card crypto outside
gbnltunnel card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto gbnltunnel interface card
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = GBNLVPN.greatbrandsng.com, O = GBNL, C = ng
Configure CRL
Crypto ikev1 allow inside
Crypto ikev1 allow outside
Crypto ikev1 enable backup
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
enable client-implementation to date
!
track 10 rtr 100 accessibility
!
Track 100 rtr 10 accessibility
Telnet 192.168.200.0 255.255.255.0 inside
Telnet 192.168.202.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.202.0 255.255.255.0 inside
SSH 192.168.200.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 backup
SSH timeout 30
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management-access inside
a basic threat threat detection
threat detection statistics
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
WebVPN
allow outside
enable backup
activate backup2
internal gbnltunnel group policy
attributes of the strategy of group gbnltunnel
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
greatbrandsng.com value by default-field
Group Policy 'Group 2' internal
type of remote access service
type tunnel-group gbnltunnel remote access
tunnel-group gbnltunnel General-attributes
address GBNLVPNPOOL pool
Group Policy - by default-gbnltunnel
gbnltunnel group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
type tunnel-group GBNLSSL remote access
type tunnel-group GBNL_WEBVPN remote access
attributes global-tunnel-group GBNL_WEBVPN
Group Policy - by default-gbnltunnel
tunnel-group 196.216.144.1 type ipsec-l2l
IPSec-attributes tunnel-group 196.216.144.1
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
HPM topN enable
Cryptochecksum:6004bf457c9c0bc1babbdbf1cd8aeba5
: end
When you say that "the external interface is downwards using failover techniques" you mean this failover occurred because the ASA is no longer able to reach the 31.13.72.1? Not that the actual interface is broken?
If this is the case, then the NATing is your problem. Since you're using the same VPN pool for VPN connections the ASA cannot distinguish between the two streams of traffic if the external interface is still in place. The SLA tracking only removes a route in the routing table, but does not affect what happens in the NAT process.
try to change the NAT statement follows him and the test (don't forget to remove the other statements to exempt of NAT for this traffic during the test):
NAT (inside,any) static static source NETWORK_OBJ_192.168.30.0_25 destination DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.30.0_25
If this does not work, I would either turn off the external interface when a failover occurs, or create a second connection profile that contains a separate mass of IP for the VPN connection and ask users to connect using this profile when a failover takes place. Don't forget to create Nat exempt instructions for this traffic also.
--
Please note all useful posts
-
established - VPN connection, but cannot connect to the server?
vpn connection AnyConnect is implemented - but cannot connect to the server? The server IP is 192.168.0.4
Thank you
ASA Version 8.2 (1)
!
hostname ciscoasa5505
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.0.3 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 208.0.0.162 255.255.255.248
!
interface Vlan5
Shutdown
prior to interface Vlan1
nameif dmz
security-level 50
IP address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS lookup field inside
DNS server-group DefaultDNS
192.168.0.4 server name
Server name 208.0.0.11
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service TS-780-tcp - udp
port-object eq 780
object-group service Graphon tcp - udp
port-object eq 491
Allworx-2088 udp service object-group
port-object eq 2088
object-group service allworx-15000 udp
15000 15511 object-port Beach
object-group service udp allworx-2088
port-object eq 2088
object-group service allworx-5060 udp
port-object eq sip
object-group service allworx-8081 tcp
EQ port 8081 object
object-group service web-allworx tcp
EQ object of port 8080
allworx udp service object-group
16001 16010 object-port Beach
object-group service allworx-udp
object-port range 16384-16393
object-group service remote tcp - udp
port-object eq 779
object-group service billing1 tcp - udp
EQ object of port 8080
object-group service billing-1521 tcp - udp
port-object eq 1521
object-group service billing-6233 tcp - udp
6233 6234 object-port Beach
object-group service billing2-3389 tcp - udp
EQ port 3389 object
object-group service olivia-3389 tcp - udp
EQ port 3389 object
object-group service olivia-777-tcp - udp
port-object eq 777
netgroup group of objects
network-object host 192.168.0.15
network-object host 192.168.0.4
object-group service allworx1 tcp - udp
8080 description
EQ object of port 8080
allworx_15000 udp service object-group
15000 15511 object-port Beach
allworx_16384 udp service object-group
object-port range 16384-16393
DM_INLINE_UDP_1 udp service object-group
purpose of group allworx_16384
object-port range 16384 16403
object-group service allworx-5061 udp
range of object-port 5061 5062
object-group service ananit tcp - udp
port-object eq 880
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-6233
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-1521
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing2-3389
outside_access_in list extended access permit tcp any host 208.0.0.164 eq https
outside_access_in list extended access permit tcp any host 208.0.0.164 eq www
outside_access_in list extended access permit tcp any host 208.0.0.164 eq ftp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing1
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 EQ field
outside_access_in list extended access permit tcp any host 208.0.0.162 eq www
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 remote object-group
outside_access_in list extended access permit tcp any host 208.0.0.162 eq smtp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 object-group olivia-777
outside_access_in list extended access permit udp any host 208.0.0.162 - group Allworx-2088 idle object
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5060
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group web-allworx inactive
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group inactive allworx-8081
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-15000
outside_access_in list extended access permit udp any host 208.0.0.162 DM_INLINE_UDP_1 idle object-group
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5061
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 inactive ananit object-group
outside_access_in list extended access deny ip host 151.1.68.194 208.0.0.164
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
permit access ip 192.168.0.0 scope list outside_20_cryptomap 255.255.255.0 172.16.0.0 255.255.0.0
Ping list extended access permit icmp any any echo response
inside_access_in of access allowed any ip an extended list
permit access ip 192.168.0.0 scope list outside_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
access-list 1 standard allow 192.168.0.0 255.255.255.0
pager lines 24
Enable logging
logging buffered stored notifications
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
IP local pool 192.168.100.30 - 192.168.100.60 mask 255.255.255.0 remote_pool
192.168.0.20 mask - distance local pool 255.255.255.0 IP 192.168.0.50
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.0.0 255.255.255.0
alias (inside) 192.168.0.4 99.63.129.65 255.255.255.255
public static tcp (indoor, outdoor) interface 192.168.0.4 smtp smtp netmask 255.255.255.255
public static tcp (indoor, outdoor) interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 192.168.0.4 www www netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 777 192.168.0.15 777 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 779 192.168.0.4 779 netmask 255.255.255.255
public static (inside, outside) udp interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 880 192.168.0.16 880 netmask 255.255.255.255
static (inside, outside) 208.0.0.164 tcp 3389 192.168.0.185 3389 netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 208.0.0.161 1
Route inside 192.168.50.0 255.255.255.0 192.168.0.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.0.0 255.255.255.0 inside
http 192.168.0.3 255.255.255.255 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt noproxyarp inside
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 108.0.0.97
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 69.0.0.54
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life no
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 1
life no
Telnet timeout 5
SSH timeout 5
Console timeout 0
identifying client DHCP-client interface dmz
dhcpd outside auto_config
!
dhcpd address 192.168.0.20 - 192.168.0.50 inside
dhcpd dns 192.168.0.4 208.0.0.11 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal group anyconnect strategy
attributes of the strategy group anyconnect
VPN-tunnel-Protocol svc webvpn
WebVPN
list of URLS no
SVC request enable
encrypted olivia Zta1M8bCsJst9NAs password username
username of graciela CdnZ0hm9o72q6Ddj encrypted password
tunnel-group 69.0.0.54 type ipsec-l2l
IPSec-attributes tunnel-group 69.0.0.54
pre-shared-key *.
tunnel-group 108.0.0.97 type ipsec-l2l
IPSec-attributes tunnel-group 108.0.0.97
pre-shared-key *.
tunnel-group anyconnect type remote access
tunnel-group anyconnect General attributes
remote address pool
strategy-group-by default anyconnect
tunnel-group anyconnect webvpn-attributes
Group-alias anyconnect enable
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the icmp
!
service-policy-international policy global
: end
ASDM location 208.0.0.164 255.255.255.255 inside
ASDM location 192.168.0.15 255.255.255.255 inside
ASDM location 192.168.50.0 255.255.255.0 inside
ASDM location 192.168.1.0 255.255.255.0 inside
don't allow no asdm history
Right now your nat 0 (NAT exemption) follows the access list:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
Traffic back from your server to 192.168.0.4 in the pool of VPN (192.168.0.20 - 50) not correspond to this access list and thus be NATted. The TCP connection will not develop due to the failure of the Reverse Path Forwarding (RPF) - traffic is asymmetric NATted.
Then try to add an entry to the list of access as:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.0.0 255.255.255.0
It's a bit paradoxical but necessary that your VPN pool is cut out in your interior space network. You could also do like André offers below and use a separate network, but you would still have to add an access list entry to exempt outgoing NAT traffic.
-
VPN connects, cannot get to anything on the LAN
OK, what don't get me? My VPN connects OK with the Version of the Client 5.0.07.0290 VPN but I can't access anything on the 10.0.0.0/24 network.
Any thoughts? I should be able to ping the server 10.0.0.90 if it worked properly in my laptop while I'm on the VPN. Following configuration:
ASA Version 7.2 (4)
!
hostname XXXX
domain energy.com
activate jp28ZvYIS1PQVK6M encrypted password
UmzM9i7pSqpXEdTR encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 10.0.0.9 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address 74.x.x.150 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone IS - 5
DNS server-group DefaultDNS
domain energy.com
access-list 101 extended allow ip 10.0.0.0 255.255.255.0 192.168.150.0 255.255.255.0
access-list sheep extended ip 10.0.0.0 allow 255.255.255.0 192.168.150.0 255.255.255.0
outside_in list extended access permit tcp any host 74.x.x.146 eq 35330
outside_in list extended access permit tcp any host 74.x.x.147 eq 10000
outside_in list extended access permit icmp any one
outside_in list extended access permit tcp any host 74.x.x.148 eq 990
outside_in list extended access permit udp any host 74.x.x.148 eq 900
outside_in list extended access permit tcp any host 74.x.x.148 4000-4099
access-list extended outside_in permit udp any host 4000-4099 74.x.x.148
outside_in list extended access permit udp any host 74.x.x.148 eq 990
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 100000
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool dhcppptp-192.168.150.1 - 192.168.150.20
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.0.0.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
public static 74.x.x.146 (Interior, exterior) 10.0.0.90 netmask 255.255.255.255
static (inside, outside) 74.x.x.147 10.0.0.91 netmask 255.255.255.255
public static 74.x.x.148 (Interior, exterior) 10.0.0.3 netmask 255.255.255.255
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 74.x.x.145 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
Enable http server
http 10.0.0.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto dynamic-map cisco 1 transform-set RIGHT
dynamic dyn-map 20-isakmp ipsec crypto map Cisco
dyn-map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 1
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet 10.0.0.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
TFTP server inside 10.0.0.109 cpix.cfg
internal BEVPN group policy
BEVPN group policy attributes
Server DNS 10.0.0.4 value 10.0.0.1
VPN-idle-timeout 30
Split-tunnel-policy tunnelall
Split-tunnel-network-list value 101
maindomain.com value by default-field
disable authentication of the user
IPSec-attributes tunnel-group DefaultL2LGroup
pre-shared-key *.
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
ISAKMP ikev1-user authentication no
tunnel-group BEVPN type ipsec-ra
attributes global-tunnel-group BEVPN
address-pool dhcppptp pool
Group Policy - by default-BEVPN
IPSec-attributes tunnel-group BEVPN
pre-shared-key *.
ISAKMP ikev1-user authentication no
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the preset_dns_map dns
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:b379566df0e7f5213ad2396676763859
: end
Hello
I don't see the NAT0 configuration more in this configuration
NAT (inside) 0 access-list sheep
You can also change the ACL of Split Tunnel
standard access list permits 10.0.0.0 SPLIT-TUNNEL 255.255.255.0
BEVPN group policy attributes
no value of split-tunnel-network-list 101
Split-tunnel-network-list value of SPLIT TUNNEL
You can also use the "show run" command that will generate a little less production
-Jouni
-
Add a vpn connection in ios 10, method chosen in IKEv2, but I don't have the remote ID. My VPN is created in Sonicwall, waiting for quick reply
Hi cmscan,
Thank you for using communities of Apple Support.
I see that you add a VPN connection using IKEv2, but you do not have the remote ID. I know it's important to be able to set up a virtual private network, you can connect using your iPhone. I'm happy to help you with this.
You must contact your system administrator to ensure that the settings that you must configure the VPN connection. Please see the iPhone user Guide for more information.
Have a great day!
-
VPN connection error - pppd limited
Hi I think I have a problem with OX, the captain and the networks, I sail perfectly with the team but since update stops running the VPN, I tried the possibility to go to recovery mode to 'disable csrutil' then ' sudo chmod u + s / usr / sbin / pppd "but it does not work when you use Netextender or FortiClient." I have another Mac with Lion and works properly the only difference I notice in the file 'pppd' Captain makes me 'limited, compressed' and only 'compressed' Lion I put a photo and a newspaper of netextender:
15/09/2016 10:15:59.271 [603 General info] NetExtender 8.1.788 for Mac OS X initialized
15/09/2016 path of the bundle app NetExtender 10:15:59.299 [General info 603] = /Applications/NetExtender.app
15/09/2016 createLogPanel() 10:16:01.045 [gui info 603]
15/09/2016 10:16:01.730 [config info 603] loading saved profiles...
15/09/2016 10:16:16.507 [connect info 603] user: "prueba".
15/09/2016 10:16:16.507 [connect info 603] domain: "abcd.hos."
15/09/2016 10:16:16.509 [connect info 603] Server: 'vpn.abcd.es:444 '.
15/09/2016 10:16:16.581 [603 general notice] connection to vpn.abcd.es:444...
15/09/2016 10:16:16.820 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)
15/09/2016 10:16:16.821 [General notice 603] retry...
15/09/2016 10:16:16.822 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)
15/09/2016 10:16:16.823 [General error 603] authentication failed: connection failed. See the log for more details.
15/09/2016 10:16:16.823 [General error 603] NetExtender connection failed.
15/09/2016 10:16:16.823 [General notice 603] SSL VPN disconnect...
15/09/2016 10:16:17.058 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)
15/09/2016 10:16:17.058 [General notice 603] retry...
15/09/2016 10:16:17.060 [General error 603] ERROR: SSL_connect: Undefined error: 0 (0)
15/09/2016 10:16:17.061 [General error 603] disconnect command failed
15/09/2016 10:16:17.063 [General notice 603] SSL VPN connection is completed.
15/09/2016 10:16:17.063 [config info 603] loading saved profiles...
15/09/2016 10:16:17.065 [gui info 603] connection failed. See the log for more details.
I think that the problem is a network file or because I put the wrong password and I cannot detect this error. as I said the VPN working properly with another MAC using the same network.
Help...
You shouldn't be messing with the security features of the operating system.
Problems may have to do with the network, or client software that you use.
I start by making sure all the software are updated and then create a new entry, vpn, double control system that everything has been entered correctly.
FWIW, I use the built-in features of VPN on El Capitan to connect to my University regularly and without problem.
I'm not familiar with "Fortinet", and I suspect that you may need to be updated, or simply use the built-in VPN.
-
VPN connection: An unexpected error has occurred.
I am suddenly unable to get my built-in VPN connection works on my iMac with OS X 10.11.5. I get the VPN connection message: an unexpected error has occurred. I have been using this VPN configuration to connect to work for several months with success.
But last week (and I do not know if it had nothing to do with it), I went on vacation and used a free wi - fi setup of Tim Hortons. I had a LOT of trouble getting the next login page, and I checked all playing with different settings of network without success. When a change did not work, I put it to its original setting. Finally, I learned to use Safari to access the free WiFi connection page of Tim. Then once connected, everything was OK.
But when I returned a week later and if necessary, to start my VPN connection to access the work, it wouldn't start. I checked and recheck all my settings preferably of different network, but did not find those who were wrong. I even deleted and re-entered my VPN service definition without solving the problem.
Thinking that the problem could be the newly installed ISP of Bell equipment (we went from Rogers while I was away), I used my BlackBerry smartphone (issued by my employer) to create a wi - fi hotspot and accessed to the internet using this connection which completely ignored my home ISP equipment. But still, I was unable to establish a VPN connection.
I then tried my iPad VPN connection, and it worked! Then, I defined a VPN service on the iMac to my wife and the iMac to my daughter and was able to successfully establish a VPN connection to my work very well, using exactly the same VPN configuration. This led me to the conclusion, it was a problem on my iMac (and not with my new ISP or VPN system of my work that had none of the changes you made), but I still can't find what is "broken". I run Onyx for my iMac OS X 10.11.5 and repaired permissions and clean the cache and all the rest she is doing to "solve" problems. But the problem persisted.
Is there a preference file corrupted somewhere (scan option is no longer on the current version of the Onyx for a reason any)?
I still have a network setting wrong somewhere I need to go back to the system is correct value?
Here is the attempt to VPN from the file system.log (with some hidden values in the case where they display my work VPN access):
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: received an order to start SystemUIServer [257]
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: changed to connecting status
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec connection to server nnn.nnn.n.n
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: phase 1 of the IPSec from.
26 June at 16:13:48 Myrons-iMac raccoon [520]: agreed to the takeover of vpn connection.
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec connection to server nnn.nnn.n.n
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: connection.
26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec Phase 1 started (initiated by me).
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: bind 1 (cannot assign requested address)
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: sendfromto failed
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: Phase 1 negotiation failed due to the error of sending. 94437eb7d5b1b6e8:0000000000000000
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: can not send packets
26 June at 16:13:48 - last message repeated 1 time-
26 June at 16:13:48 Myrons-iMac raccoon [520]: IKE Packet: send failed. (Initiator, aggressive Mode 1 Message).
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: Controller IPSec: IKE FAILED. Phase 1, assert 0
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed by disconnecting
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec disconnection from the server 142.201.5.6
26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec disconnection from the server nnn.nnn.n.n
26 June at 16:13:48 - last message repeated 3 times-
26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed to offline, terminus right no
Any help or insight would be more useful and appreciated... so that I can work from home again.
Thank you
Myron VanderLaan
I finally found my VPN problem.
There is a 'racoon' file that is generated when I connect to the VPN to my work site.
I have created a modified version of this file so that my connection does not expire in 3600 seconds (changed in 24 hours).
Apparently, there are some slightly different settings (such as certain IP addresses other than VPN IP of my work) in this file under our new ISP Bell from the former FAI Rogers.
And if I connect to the WiFi Hotspot from my BlackBerry, it does not once again because these settings in the file are different again. I must return the file generated instead of my modified file.
Bad luck!
-
Is it possible to get Win 7 auto start VPN connection?
Hey all,.
Is it possible to get Windows 7 auto start VPN connection? Or can you recommend a 3rd party VPN client application?
Thank you
Hello
You can make a batch file exe or cmd and autostart. The command line should be like this:
RASPHONE d * where is * a name of your VPN connection
For example: your Vpn connection is called my VPN
The command line will be:
RASPHONE d my VPN
-
I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are grayed out, it is a Windows component is missing and does not allow me to create VPN. I am running Windows XP Home addition. I recently got a Malware attack and had the quarantine and fix trojen attempts. After the restoration, I found that my previous VPN connection was broken. When I tried to add a new connection, I'm stuck on the screen connection virtual network in the the radial button private network connection wizard is grayed out, he could not check.
Hello
Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows XP TechNet forum. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en/itproxpsp/threads
-
error on the remote desktop and VPN connections
Unable to connect using desktop remote or VPN. remotes can't find the computer at home on the network and the VPN gives me an 800 error code. I used the remote desktop, but it says my work computer isn't on this network and the VPN connection fails. We checked everything using remote assistance, but it becomes too hard and not responses. Help!!!!!!!!!!!!!!!!!!!
Hello
Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
Please post your question in the TechNet Windows XP category.
Here is the link:
http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads
I hope this helps.
Thank you, and in what concerns:
Shekhar S - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
Maybe you are looking for
-
HP Envy 14 1190ea AMD driver problem
Hello.I searched for some time now to update the drivers for the graphics card processor. But I have not found a solution. Yes, after running Windows Update two days ago, I discovered that the switchable graphics are no longer working and everytime I
-
I can't create an installer on LabView, after install the Vision Builder demo and then uninstall it. I can't create a Labview Installer more, he asks me an installer of generator of Vision, even if Labview my program does not have nothing to do with
-
Is there a maximum number of clients to one opc Server opc
I created a server using this tutorial: http://digital.NI.com/public.nsf/allkb/CC9CDD577F041786862572120061EB5A I am noto using NI OPC Server (I think) and I'm using DSC noto (obviously) Is there a maximum number of customers mutual funds for an opc
-
My computer stops just after I turn it on
The lights come on for a few seconds only. I have everything turned off (sector & the switch of the computer in the back) before trying again. I use Windows XP.
-
"Attachment ID has wrong format" when you reply to emails in hotmail
"Attachment ID has wrong format" keeps appearing on I answer all emails. Then, he does not send once I typed the answer and lost my response to the first attempt. At the moment I am each time to avoid losing the message and then paste the return mess