L7590 Black Print Missing tapes project and Normal but no better way

Problems with black project and print in normal mode for L7590 model CB821A.   After the printer has been turned off for about a month and then switched back, began to have horizontal bands across the exit who did not text/image, which should have been printed in black when printing in draft or Normal print quality.  Black okay impression is better quality.  "Logically the black output appears as if printed in approximately 7/8" wide sections/blocks on the page where the last 1/16 "(bottom) of each section is missing a release which should have been printed in black.  See assessment below one hatched filled printed image print black lines - i.e. the white strips between the blocks are portions of output that was not printed (but should be).  The problem occurs for the black out in draft or normal quality: the entire image without lack of bands is printed if black best quality mode is selected the problem appears only for ink black/output.  Output color (all three color cartridges) doesn't include any missing tapes for any mode of output quality (draft, normal or best).  Except where the output on the page aligns with the missing 1/16 "areas/bands, a diagnostic page is OK, print quality running print head alignment, calibration of jump line and cleaning of the printheads (several times) has no effect (fix) the printing problem.  Also to install a new Black XL cartridge does not change/fix anything.  Any idea on what to do to solve the problem?  Oh and also when making black copies of the production of documents in the printed copy of the document is lack as the black print in bands through the page at least that the best quality copy is selected.

Advertisement

Hi Sunshyn2005,

Thanks for the reply.  I had already seen and tried things in the link streaks of ink, fixing faded prints and other common print quality problems without any noticeable change in the sysmptoms of the problem.  Not knowing the logic of printing in detail the process, I was hesitant to assume that the problem was due to a print head (related as good) without knowing with certainty that if she could be the cause of the problem.  I had also seen the link following re manually cleaning/replacement of the print heads, etc. to:

""http://support.hp.com/us-en/document/c01446637 " "

Given no other definitive solutions, I pulled the Black/Yellow Printhead, cleaned the mechanical contacts (even if they appear dirty) and reinstalled print head.  After that hard restart of the process, the printing problem looked pretty much the same, but I used the printer console to clean the print head, align the print head and calibrated the line break.  Note that focus 3 on the print quality Diagnostics printout showed areas in white/white near the arrows, but unprinted areas also appeared on each 7/8 "in the set/bottom of the full page and calibrations of previous line break had not changed was not clear if the blank spaces seen were really due to power problems line.

In any case, I noticed in successive test prints, that no printed space has changed a little bit stable after things after replacing the print head and of cleaning and calibrate things.   After still print tests (change in volume of ink, paint, modes of quality, margins, etc) portions of unprinted line (~7/8' down the entire page) began to shrink.  After having used the services of printer to do about cleaning printhead plus 4-5, 3-4 alignments print head, line 11 or if several calibrations break line and a lot of printing of tests between the two, non-printed portions have been reduced in height for only the width of a couple very ink drops (project or normal mode; no unprinted areas in don't best way).

Thus even if the problem persists, it has been barely perceptible.  At this point, I'll just keep feeling and see if things eventually clear up all the way.  Maybe I'll try an inexpensive refurbished printhead later if things do not completely delete (to prove it fixed / improves things before buying a new expensive).  Note that at this point sight 3 to print the print quality Diagnostics always shows a notable, but very light gap point arrows (with a magnifying glass you can see it is not completely empty, but contains scattered points of ink and the gap is only a point or two high).

So... maybe the printing problem is actually "fixed" - at least it is enough now usable for the print project routine / normal for most cases.

r/cover4me

Tags: HP Printers

Similar Questions

  • Can I change my 8600 more print quality settings in a framework between the project and normal

    Officepro 8600 more

    Windows 7 32 bit

    How can I print 'between' projects and normal settings?

    I'm sorry you say crhfool, but there is no option between the 'Project' and 'Normal' on the 8600. The three main choices that you are 'Project', 'Normal' and 'Best '. They determine the density of 'points' by your inkjet printer, and the printer will always default to the setting chosen.

    I hope this information is useful!

  • DeskJet 3520: no black print with new ink and genuine cartridge is full

    No black print with genuine new cartridge ink level shows and complete.  Many other colors are printed. This happened after I made the print heads clean and clean ink smears.

    Thanks for the reply

    Now, if you were to call to our technical support team, they should be able to implement a replacement for you for this printer model, regardless of the status of the guarantee.

    Call them and let me know how things are going for you!

  • Never had the CD for my laptop Window XP Pro OS or Pro Office, Visio, project and PP but now I need to reinstall.

    I need to change my phone to a double partioned Window NT (drive C) and Window XP Pro (drive E to a single disk with XP but I have not never have the CD of the operating system XP or Pro Office, Visio, PP and the project.)  I understand I have to format the drive unique and which will be wip on everything, including the data of the user.  How can I get the OS and the App CD "s to proceed?

    See: How to replace Microsoft software

  • How to print an e-mail and attachment, but with open attachment.

    I just want to print an email and it is incidental (e.g. pdf) but with the open pdf, not as an icon/link. Is it possible or ' add to ' who can do this?

    No you can not just print a pdf attachment without opening it. Nor do so with one attachment other than text, eml and a few image as jpg and png formats

  • Photosmart HP 6510: Black print failed

    I have a HP Photosmart 6510, which will not print black - pages of text, sound as if they are printing, but the page comes out blank. Watch as the color test page, but not black.  There is no error message.  Black print cartridge is full and I have applied all recommended maintenance procedures.  I'm going to disassemble the printer (which is out of warranty) and the print head to check the visible obstructions before deciding to give up completely and use my backup of Canon.  Can anyone suggest any other remedies or advice on removal of the print head?  Thank you.

    Thanks for your suggestions.  I removed and cleaned the print head, but the problem remains unresolved.  I did more research and decided to go deeper into the printer to access tubes empty below the print head.  I couldn't find all the instructions more complex procedure on the HP site or elsewhere online, so most of the work was intuitive.  I managed to remove the 'well' below the print head complete with 4 vacuum tubes, and it was immediately obvious to me that the black ink tube was clogged.  I went to clean the whole by immersing in hot water and using a syringe to flush out the tubes.  I cleaned too much ink frozen since sponges of drain that receives the excess ink from the vacuum system (no doubt mostly print head last cleaning operations).  After drying of the parts and reassembling the printer, everything is back to the fully functional State.

    I was amazed at the amount of vitriol expressed by users of the forum to HP for what seems to have been a recurring problem with these printers.  It seems incredibly useless to throw a sound mechanical printer because of a dried ink problem, but that's what many did the cost of 2-3 hours time technician to fix the problem simply cannot be justified. It is unfortunate that HP provides no instructions for technical people like me who are willing to undertake their own maintenance out of warranty HP products.

  • Black printer only print not

    I have a C310 printer wireless connected to my laptop HP DV7 64 bit on Windows 7. This printer has been great until today. I tried to print 3 documents in blue, red and black. The red and blue are fine, but the black is not printing. I printed a document of ink, and the text does appear not even if all the colors, including black, print. I removed and replaced the black cartridge and I checked that there is ink available, that there is, and I checked for ink in the ignition and that is. Anyone know what could be the answer and how I started to correct. Thank you.

    Gordon

    For all those who have involved in this post, thanks for trying, but I have now come to the conclusion that the printhead has gone wrong on me, having followed the links and discussions of this forum and the Forum of Microsoft. The end result seems to be that the print head needs to be replaced, but rather than do this for £48 I will probably inveat in a new printer as the 6520 and hope that it lasts longer than the short time - approx. 2 years - that it was successful.

    Gordon

  • Just bought a new I Pad Air 2 December 4, 2015.  IBook started with a printed blue/white background.  The next day woke to white/black print and can not return blue background.

    Just bought a new I Pad Air 2 December 4, 2015.  IBook started with a printed blue/white background.  The next day woke to white/black print and can not return blue background.

    Open a book, tap, tap of he two, disable auto-nuit theme.

  • HP envy 5532 - poor black printing - trailed missing lines showing

    Hello

    I just bought the hp envy 5532 and found poor print quality.

    While color printing seems to be okish, black is very poor.

    I tried all the tools available via the control panel of the printer, but there are always problems with black printing.

    It's almost as if the black is missing from the lines and. For example on test prints that print a block in black, some of the block is low or striated.

    Runs all tests in diagnosis is also eating away at the ink and not started using the printer to its destination.

    Please help, I really do not want to return the printer, but will do if this is not resolved.

    Thank you

    Bobonthejob.

    Hello Bobonthejoband welcome to the Forums of HP.

    I see that you have print quality issues.  I would try to help.

    I recommend removing the cartridges and perform a power reset. Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

    I also recommend later in this document on the streaks of ink fixing faded prints and other common Print quality problems

    Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums.

  • Black print L7590 performance

    I'm curious to know if anyone else has experienced this problem. I printed the 124 pages and my black cartridge was released (the cartridge is standard HP88). What of the 850 pages give HP announced. Why is there such a huge difference?

    I want to go back to my black laser printer... who was still a hp but...

    Model name: HP Officejet Pro L7500 model number: CB821A serial number: Service ID:use of ink (ml or cc) Black: 29.461 Cyan: 2.627 Magenta: 2,592 yellow: 3.002 media size A4/Letter: 124 envelopes: 0 other: 0 media Plain: 124 Photo: 0 other: 0

    NEB1, have you tried to change the setting of the Volume of ink on the advanced properties wndow Printer Options tab? I had to drop mine a bit to stop some burrs on the postage labels and was very surprised to find that I could not only give up one or two levels and keep a strong page, but could lower the level of use until the setting lower and still print jobs of high quality. As we have done on our L7590, I would say that they are using probably 1/3 the ink they were originally. Now if we could just get them to stop to pick up more than 1 sheet of paper at a time... (Has nothing to do with the volume of ink; they have always had this problem)

  • Photosmart7520: What cartridge is used for normal black printing?

    I seem to use a LOT of black ink. The 564 is used for normal printing in black or the 564XL? The xl is much broader. Is it possible to have both? I'm tired of buying sets of ink cartridges when I don't need than black.

    As I mentioned here, I'll throw in my $0.02.  If the black cartridge was more than half full but seems to be empty the probable thing to check would be the event.  If the vent is blocked the cartridge seems to run out of ink, even though there was a lot of ink in the cartridge. For more information on the verification of the evacuation of the cartridge area, refer to step 9 of the document here.

    1. Figure: Evacuate the area on top of the ink cartridge

  • DeskJet 1055: Custom printer printing, Dim. power light and back to normal

    Hello

    I bought this printer in America and I took it with me to Brazil, where I live now.

    The scanner in it works very well, and also the test page prints fine.

    But when I try to print my own pictures, he used impression. Its like the printer simply ignores the document. My computer tells me the print job, or sometimes didn't display any status at all in the print list. And the power light fades and returns slowly to normal.

    It has new cartridges, and I can't seem to make it work. Function print and Scan Dr. I have all possible updates and its all supposed to work very well.

    Can you guys please help me? I contacted the support to the Brazil, but told me that I should talk to HP WE.

    Its a shame that the product does not work, this printer has been barely used...

    Thank you

    Hi @Laridk,

    Welcome to the Forums of HP Support!

    I see that you are unable to print to your HP Deskjet 1055 printer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

    I understand that the printer is capable of printing a test properly page. This seems to indicate that this isn't a hardware problem and it is more likely to be software related problem.

    Due to the slight dimming, I would like to do a hard reset to see if that will solve the problem.

    • Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
    • Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
    • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

    Please confirm that you have the printer connected to the USB 2.0, rather than a USB 3.0 port.

    In addition, please try the steps in these guides:

    In addition, you have regionalized the printer or do you still use the ink cartridges, you bought the United States?

    Here is more information on this topic: HP printers - find and install the cartridges after moving to another country.

    When you need to use ink cartridges purchased at the Brazil. The printer should be regionalized. When this happens, contact HP.

    Contact HP for service in all countries except Asia-Pacific.
    What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
    Step 1. Open the link: www.hp.com/contacthp/
    Step 2. Enter the product number or select Auto detection
    Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
    Step 4. Scroll down and click on: contact HP options - click Get phone number
    File number and phone number are displayed.

    Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

  • 8500 - alignment failed and black print proberly dosnt

    Hello

    I have a problem with my 8500 has.

    When I run the alignment, then it has sometimes failed. The black printing ink dosnt too proberly. I tried to run clean print head and tried to run the alignment many times.

    If I don't use the printer for a while, so I can print 1-2 pages in black once again, and then the black ink stop working again.

    I checked the cables of the ink and tried other solutions to the support page, but nothing seems to work.

    Would it work if I replace the print head, or know someone at - it a fix for this?

    Best regards, Anders

    Hi @AndersGK and welcome to the Forums of HP!

    I see that you have print head problems.  I would try to help!

    It seems you have a lot of troubleshooting already covered.  It is possible, that you can start to encounter a failure of the print head.

    I recommend to remove the ink cartridges and performing a power reset the printer.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

    I would also recommend using the steps described in this document on the problems of quality Print for the HP Officejet Pro 8500 has e-all-in-one printer series.

    Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

  • PIXMA MG5320 stopped printing black even with new cartridge and a deep cleaning. The colors are OK.

    Some time previously, failure to print quality settings, black would go a little weak on the last few lines of a full page of text. If there are more pages, each would start very well but have the same poor quality near each bottom of page. I changed the setting of the standard high quality & the problem seemed fixed. Just course several days showed poor quality at the bottom of the pages. Today, black does not print. I did 2-3 deep cleanings with a new cartridge, but still no black. Color printing very well. I need to replace the print head?

    Hi PMHilton,

    Given that black ink is printing is no longer and to replace the ink tank and perform deep cleanings have not solved the problem, the printer may require repair.  We ask that you call please 1-866-261-9362, Monday - Friday 10:00-10: 00 ET (excluding holidays) for assistance.  A Canon technical support representative will be happy to help you.  There is no charge for this call.

  • HP7520 printer using the photo cartridge during the printing of the documents not General and black print cartridge

    My 7520 printer uses the photo and not the General black cartridge when printing on plain paper documents. The black general still full but my photo cartridge runs out of ink.

    Hi shay!

    My apologies, I didn't know that your prints come out in blue print when you have a totally black cartridge. It is a problem of print quality with the printer or something in the settings of your computer.

    I suggest to try the steps in the guide below. You have already tried some troubleshooting, try so the steps that you have not yet tried, I understand:

    The streaks of ink fixing, faded prints and other common print quality problems

    If you're still only able to print in blue (no black print), so I recommend you call HP to let them know. As you mentioned you have only had the camera for 3 months, it is likely under warranty and you might need a spare part or unit.

    Here are the details of HP:

    If you call in North America, the number is 1-800-474-6836 and for all other regions: click here.

    I hope this problem is solved for you, have a wonderful Wednesday

Maybe you are looking for