LabVIEW Interface for installation of the Arduino

Similar Questions

• Upgrade Vista to Windows 7 error: "Windows cannot copy files required for installation. The files may be damaged or missing. Error Code Ox80070017.

  I am upgrading of Windows Vista Home Premium (32-bit) for Windows 7 Home Premium (32 bit) - but getting stopped everytime I try, I end up with a dialog box stating: "Windows cannot copy files required for installation. The files may be damaged or missing. Make sure all files required for installation are available, and restart the installation. Error Code Ox80070017.

  What should I do to resolve this problem and allow full of Windows 7 installation? (my computer is a Compaq Presario V6000).

  Hello

  What installation media you are using?

  Method 1:

  Error 0 x 80070017 translates "CRC error" which means that the files that are copied from the disc are not making it to the hard drive with the same structure, which means that the 'original' the disk files are modified/changed/corrupted while being copied to the location of the 'destination' on your disk during Setup.

  This usually means a bad DVD, or an error reading on the DVD player.

  I suggest you follow the link and check.

  Upgrade Windows Vista to Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-Vista-to-Windows-7?T1=tab02

  Method 2:

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  WARNING: There may be loss of data through an analysis using firewall to eliminate the virus as appropriate

  Method 3:

  I also suggest you to follow the link and check.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

• Windows cannot copy files required for installation. The files may be damaged or missing. Error code: 0 x 80070241.

  I had a lot of trouble trying to install the 64-bit version of windows 7 Home Premium on my 64-bit vista, and my question is multi-part. If it is relevant, it's my 2nd copy of windows 7 I have tried. Initially, I had the problem of not being able to run the installation on two copies with the error "'autorun.dll' could not be found or is damaged. Error code is [0x7E]. "However, I managed to get into with my 2nd copy installation after restarting my computer. Once in Setup, I got another error that stopped the installation that says "windows not could create an installation folder. Error code is 0 x 80070017. "Again, I rebooted my computer and started the installation again, this time following installation was decently through but stopped when I got the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. "I then backed up and restarted my computer and then tried to use the option to install custom but then got the error"E:\sources\autorun.dll is not designed to run on windows or it contains an error. Try to install the program using the original media, or contact your system administrator. "coupled with the error"the file 'autorun.dll' could not be loaded or is corrupt. Error code is 0xC1"again once I restarted and tried the custom option but got the error" Windows has no load the required file WinSetup.dll.» The file is possibly corrupted. To install windows, restart the installation. Error code is 0x3E6. "I restarted my computer and tried the custom triple option more and still have the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. »

  I understand that my problem is very complex, but it seems to be built around a missing or damaged file. Thanks if you can tell what's wrong or what to do.

  Tips for solving common problems when Windows 7 won't install troubleshooting

  1. start Windows Upgrade Advisor to see if there are known issues that might affect the installation and correct them.
  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  2 disable any security software, including anti-virus programs and firewalls.
  3 make sure that your computer has the BIOS and latest drivers.
  4. disconnect all external devices except the keyboard and mouse before installing.
  5. If your computer/motherboard integrated video use and remove the dedicated video card.
  6. If you have a large amount of RAM (memory), try to reduce the amount of RAM installed. 1 GB if 32-bit installation, 2 GB for 64-bit, then replace RAM if the upgrade was successful.
  7. If you have downloaded Windows 7 and it burned a DVD test burn again at the slowest speed possible. It is also possible the download may have errors, you can try to download it again.

  8. check your RAM (memory) to find errors. This can take some time.
  (A) Insert the Windows 7 DVD and restart the computer.
  (B) start from the Windows 7 DVD.
  (C) select your language, and then click Next.
  (D) click on "repair your computer" then select the operating system to fix it.
  (E) click on the link of the Memory Diagnostics in the system recovery menu.
  (F) the computer will restart and your memory is checked for errors.

  9 turn off startup programs:
  (A). Click Start, type MSCONFIG in the search box and press ENTER.
  OK the authorization of user account control and password if necessary
  If you are using XP: click Start, run, and type: MSCONFIG and click OK.
  (B) on the general tab, click Selective startup.
  (C) just below the selective startup, clear the checkbox "Load Startup items".
  (D) click the Services tab, check "Hide all Microsoft Services", and then click Disable all.
  (E) click OK, and then restart the computer.
  (F) try the upgrade again.

  (NOTE: If the upgrade fails and you continue to use your rear security software, then also go back into MSCONFIG and under the general Tower XP/Vista tab, click "Normal startup", and then click OK to exit.)

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• Best practices for installation of the equipment of the unit

  Is it possible to use the CD of hardware for installation with the unit while I'm using the correct equipment. Or is it recommended to install from scratch and apply the updates of security on the Unity software page.

  Thank you

  Tim

  I think that you are writing about Hardware configuration CD of the CallManager. If you are, then this is a NO-NO.

  You need the disks of the Platform Configuration that is provided with the server if you have purchased the license for the windows 2000 Server.

  So, if you don't have the disks in the Configuration of the platform, you can download the driver from HP hard drive controller and install Windows manually. Install SP4, IE6 Sp1 and you can use automatic Windows Update If you follow this guide:

  Support policy for the automatic update of Windows

  http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/prod_pre_installation_guide09186a008020a63e.html#wp64185

• I volunteer for installation of the Government in New Orleans.  I'm helping recommendations on equipment and software.  Their editing computer cannot be connected to the Internet.  How to buy and receive the software and updates?

  I volunteer for installation of the Government in New Orleans.  I'm helping recommendations on equipment and software.  Their editing computer cannot be connected to the Internet.  How to buy and receive the software and updates?

  Please see this link in the topic "successful."

  Creative cloud using Enterprise | Applications and updates

  You can use managed delivery of applications for the following:

  • If you need to exercise strict control over the applications installed on client computers.
  • If end-users have administrator privileges on the computer.
  • To reduce Internet bandwidth consumption by preventing multiple downloads of self-service.
  • If there is no Internet access on client computers.

• I just installed for CS5 and my option for installation of the shares does not... How to install?

  I just installed for CS5 and my option for installation of the shares does not... How to install?

  I'm just not my palette actions checked.  Fact.  Thank you.

• INS-06003: failure of connectivity SSH without password for installation with the following

  Dear all,
  
  I am in the process of installing Oracle 11 g on Redhat Linux 2 grid Infrastructure.
  I have installed ssh on both RAC nodes and when I run
  
  SSH - p7547 racnode1 "date; hostname ".
  SSH - p7547 racnode2 "date; hostname ".
  
  I get the date and the hostname without error on both nodes.
  
  But during the installation of the grid, I get this error message:
  
  INS-06003: failure of connectivity SSH without password for installation with the following nodes: [racnode1, racnode2]
  
  My thought is that it is because of the port has changed 22: 7547 but where them specify this port in the configuration of the CARS?
  
  I also get this information in the Setup log:
  
  WARNING: Could not establish a SSH connectivity with node racnode1. Reason: java.net.ConnectException: connection refused
  
  Kindly help on that.
  
  Kind regards
  Imran

  misterimran wrote:
  Dear all,

  I am in the process of installing Oracle 11 g on Redhat Linux 2 grid Infrastructure.
  I have installed ssh on both RAC nodes and when I run

  SSH - p7547 racnode1 "date; hostname ".
  SSH - p7547 racnode2 "date; hostname ".

  I get the date and the hostname without error on both nodes.

  But during the installation of the grid, I get this error message:

  INS-06003: failure of connectivity SSH without password for installation with the following nodes: [racnode1, racnode2]

  My thought is that it is because of the port has changed 22: 7547 but where them specify this port in the configuration of the CARS?

  I also get this information in the Setup log:

  WARNING: Could not establish a SSH connectivity with node racnode1. Reason: java.net.ConnectException: connection refused

  Kindly help on that.

  Kind regards
  Imran

  You can have the file/etc/ssh/ssh_config, where the default port is set at 22. Replace with 7547 and try ssh racnode1 "date; hostname". If it works, then it contains the definition, you may need to perform.

  Kind regards
  Julien

• ink advantage 4675: missing serscan.sys for installation of the scanner

  I'm trying to get this all in one printer scanner to work with my HP DV6 windows 8.1 x64machine and so far everything I've gotten is grief.
  This was initially the installation cannot find a file to install same (serscan.sys)
  All other posts said I need for an XP operating system file.
  Found one online, downloaded and run Setup to download folder, where he stopped at the second location request to the file where the installer says the file was not signed by microsoft.
  Put the same file in the C:/windows/inf folder and finally installed, but the scanner does not.

  Running the printer HP scanner doctor said there was a problem in the device manage and the unit had to be uninstalled. At this point, the only thing I can figured is the unsigned serscan file which was not duly signed.
  Got a serscan.sys since one machine virtual XP, uninstalled and reinstalled the printer with the new file in the inf folder and now the installer throws an error message...
  return to the downloaded file installed, the device but the printer does not work.

  I think I found the propblem... the serscan.sys downloaded internet and even I got the XP machine.
  Went in Windows/inf and deleted the serscan.sys.

  Then windows/system32 and did a search for the serscan.sys where research has found two files, an old man of about 2014(*i think) in a repository in system32 folder and another who was very new in the folder system32 himself.
  I copied the serscan.sys of the repository and pasted into the windows/inf and the folder windows/system32, a reinstallation of the software of 123.hp.com and everything worked!

• Lightroom will install the catalog in C:, but I need another path for installation because the hard drive c: is an SSD, it is to small for the pictures and the catalogue lightroom. How how to install lightroom on a different HARD drive?

  I need help with installation of lightroom 5 on a HARD drive, for the start of the SSD is to small for the catalog and images. Please can anyone help with information. There is no possibility of EIB "Bearbeiten - Katalogeinstellungen" ist just the way c:/users/...etc fixed. Is the anywere that can help you.

  Thanks FRANK

  Why I can not install Lightroom to a custom through the creative cloud location?

  Lightroom must be installed on your local disk and cannot be installed to a creative custom as other Cloud applications location. Lightroom always installs to the default location and does not take into account any preference you select for a custom location. This behavior is specified.

• LabVIEW, search for subVIs in the wrong directory

  I had problems with Labview for awhile. Whenever I try to use a part of the National instrument subVIs I always get a message similar to that shown in the attached photo. I know the subVIs are there because I can access their location in my installation directory and load them using Browse. But there are hundreds of them, maybe more. I can't do that for all of them and really, labview should do this automatically. I do not understand why this is happening because I only recently started with Labview and would appreciate any ideas on how I might solve this problem. Thank you.

  I would say that you have managed to move a folder, causing corrupted previous paths. Despite this, once that you pointed out a folder it should find most of the other automatically and you can save all the VI with the update path.

  You can also make the parameter Path of sure LV under Options-> paths-> VI search path, is similar to the attached picture.

  /Y

• Create a Windows Server 2008 R2 DVD for Installation of the EFI

  Is there an official method of production of compatible installation media EFI for Windows Server 2008 R2.
  I created successfully using a rough method to recreate an iso using the original media and oscdimg.exe set out in a number of unoffical positions elsewhere.  However, I ran into another issue that fits the description that is described in the following article.

  http://support.Microsoft.com/kb/975535

  I expected that the fix provided in this article would have been incorporated in SP1 of Server 2008 R2 version, but has been unpleasantly surprised to find that there was still no support. I'm more than happy to include the fix in the media but it seems that the files are identical apart from the creation date.

  I have completely updated the firmware of my server to set the server up to EFI Shell Version 2 which I hoped would solve some problems, but this did not help either.

  It seems EFI will be the way forward because of size limits of hard drive on startup disks until when can we expect a real sollution?

  If anyone has any experience with this issue so any help would be greatly appreciated.
  Thank you

  Hello

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• Update user interface for execution of the web service thread.

  I have a thread that calls a web service. This thread is run from a menu item

  public MenuItem _search = new MenuItem("Search", 10, 0){
      public void run(){
          // Code to show progress popup, either a screen or popupscreen
  
          // Start Thread
  
          // Hide popup
  
          // Navigate to page
          }
      };
  

  My code is as above!

  The thread runs and moves to the new page. The pop-up screen can't, why is this?

  Surely, I can update the user interface before starting the thread?

  How can I emplement a loading screen?

  I tried to use the locking of the event and invokelater (according to this doc) to call the UI updates but no luck?

  If you display the popup and then hide it quickly enough the BlackBerry framework don't will never paint it because painting is a low priority, always put last on the event queue. This does not change even if you use invokeLater (which is the right thing to do anyway) - unless you let the popup be for awhile before rejecting.

  The usual way to display the progress screen is to pass the handle (reference) for the popup that you create in the thread. This Thread can use then a few reminders of this popup screen to update and finally close.

  So "Hide popup" should not be in the your menu item run() method. If your 'navigate to the page' is based on the results of the background thread, remove run() of the item of menu as well.

  If you search the knowledge base for "sample"Please wait"screen", you will find an excellent example of such interaction:

  Example of screen 'Please Wait' - part 1

  Example of screen 'Please Wait' - part 2

  Example of screen 'Please Wait' - part 3

  Enjoy!

• For installation on the Windows 7 Professional 32 Bit

  I have a laptop Acer Aspire 5733. I'm from the India. My laptop was containing the Windows 7 Pro 32 Bit system. Yesterday in the morning when I tried to boot up the laptop, it showed me that it did not contain the operating system. That I tried to install the OS via the hard disk.

  Now when I tried first install the C: (system disk) he stuffed me error that Setup could not create a new partition system or locate an old existing system.
  See the logfile of installation for more information.

  Now when again when I had seen a detail for the same. It gave me an error like that.
  Windows cannot be installed to this disk. Hardware may not support booting to this disk. Make sure that the drive controller is enabled in the computer's BIOS menu.
  Windows cannot be installed to this disk. The disk may not soon. If there is another hard drive, install to a different location.

  Please help me as fast as you can. Its really urgent for me to use my laptop.

  I even formatted my whole hard drive and also tried to use the disk drivers is SATA AHCI x 86

  Looks like that is the hard drive is faulty, or the controller for the hard drive to the motherboard has failed.

  You should have some computer hardware experience look.

• Storage space required for installation of the ODI Prod

  Hello
  
  We install ODI in Linux and the customer server in the Windows machine. How much is the space allocation of memory recommended Linux server and Wimdows for the customer?
  
  Thanks for your time and your help.

  According to http://bidevata.wordpress.com/2012/04/27/installation-of-odi-11-1-1-6-on-windows-64-bit/:

  Disk space: 5GB or more
  Available memory: 2 GB or more

• Nod to the blackBerry 10-. Fire red love Ltd. For installation of the apk on BB10 phones. Security issues?

  I wanted to know if it is safe to install Snap - red light of love ltd.
  Used to download game store Google android applications.

  Is there a risk?

  John Clark, who make this post would not be posting here if there were problems with her or without integrity as a safe to install application.

  John is a user of confidence on these forums. You can take the fact that he published the instructions (and ignore the instructions if you wish).

  You are very well install the snap. Safe.