LAN Internet - unable to connect to the Internet via a LAN cable

Hello

I have an ASUS F3S laptop series running on Vista.

I went on vacation in early June this year and when

I got home that I could not access my internet broadband via the bootable.

I have an another old laptop which works fine using the local network.

I use the ASUS at work and you can get the internet via wireless LAN.

When I try to go online using the LAN laptop trying to access the internet

using the mini port WWAN and not the LAN port.

I have tried to replace the drivers and in desperation, have used the recovery

drive to get Vista back to its original setting.

I still do not have access via the LAN port.

Any ideas?

Sanquay

You must re-create the network connection Wireless LAN (remove the current which is probably set to use the mini port WWAN and create a new one) and specify the LAN port during installation.  This should solve the problem. Check out the following articles for some detailes, suggestions, troubleshooting instructions and general information that may be useful.  Pay special attention to how to remove a wireless/network connection as it differs from a regular connection, and if not done correctly can continue to exist when you think he's gone (and the system it shows same gone but is not).

Here is a tutorial on how to set up a home network (including a wireless)-click on additional links for more information that may be helpful:http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.

Here is an article on troubleshooting network connections wireless (with links):http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-network-connection-problems.

Here's a long guide on wireless internet connections in Vista:http://www.techwarelabs.com/guides/misc_mod/vistaconnection/.

Here is an article on how to set up wireless internet in Vista:http://www.clpgh.org/usingthelibrary/technology/wireless/WindowsVista.pdf.

I hope this helps.

Good luck!

Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

Tags: Windows

Similar Questions

  • Unable to connect to the printer via IP address

    I changed my ISP (internet service provider) and therefore changed routers - now unable to connect to the printer.
    I put a static IP address on my HP Photosmart B110a printer before we changed to ISP because there are connection problems. When we were setup to the ISP again, we are unable to connect to the printer, such as the printers IP 192.168.1.12
    The new network ISP IP range is 192.168.0.xx and printers address IP is out of the network.
    I can print via the USB cable but I can't return to my printers GUI by entering 192.168.1.12 return the printer back from the static IP address.
    A hard reset for this printer would be appreciated.
    Thank you very much.

    Hello
    I solved the problem. The answer was staring face heres so my solution for someone who has had similar problems.
    I didn't dig up the old router that affects the 192.168.1.xx IP network and then connected my PC, connected my printer then connected printers user interface through the static IP address, I assigned earlier. Changed to automatic IP. Connected my new router (which assigns the IP addresses of 192.168.0.xx) to my PC and printer. Everything is now OK.
    Thank you.

  • Unable to connect to the administration via the regional service console server after 11.1.2.2 installation

    Hi gurus,

    I have installed and configured the services foundation, eas and essbase in windows 2003 server, afteEA r configuration I have observed that there are no tables for eas schema then I found that it was a bug and applied patch and set up again it has been successfully configured.

    When I tried to connect to the administration via the regional service console server. He States unable to connect to the administration server. everything else works.

    I see only 4 services in services.msc

    Oracle hyperion configuration manager

    EMP web server application

    opmn services

    OSH services

    all services are started with the exception of oracle hyperion configuration manager. I tried to start, but it does not start... is - this service has an impact on the administration server.

    I checked the logs, I can't find anything in easserver.log.

    any suggestions?

    Kind regards

    Kumar

    Looks like you have deployed web applications to a single managed server that is running on a port by default of 9000, then try to add the server to the Regional service as servername:9000

    See you soon

    John

    http://John-Goodwin.blogspot.com/

  • Canning Internet connection drops when the computer is connected to the PS3 via an Ethernet cable.

    Original title: Shared network problem

    I am trying to use a shared network, configure as follows. My computer connect wireless to my router. My PS3, however, seems to be really slow when connecting wireless to the router and is at a proper speed when connected via ethernet. So, I have my PS3 connected to my computer with an ethernet cable. I put the wifi connection to be shared. Next, I set up my PS3 to connect to cable internet. Has gone through the steps and connected properly and at full speed too. However, there is a problem. My PC guard 'give up' connection to my router, while remaining connected to the PS3. I have to manually connect to my router again, regardless of the connection automatically option. Almost as if my PC is to use ethernet for internet access, (which he won't get that which is connected to the PS3) and so it loses the wifi connection. This abandonment happens around every 5 minutes or more.

    Is it possible to keep my PC connected to my wireless router and still be connected to my PS3 through ethernet to connect my PS3 using my PC?

    The problem seems to have 'fixed itself. I tried messing around with the connections that would not work even the bridge. Then I've switched back to ICS and did not have a disconnect since then.

    So the problem is now resolved, but don't know how?
    Whatever it is, I am very grateful for your help Manasa, it is well appreciated!
  • Unable to connect with the network via iphone or ipad

    Unable to connect the Apple TV (2nd generation) with the network via Wi - Fi using the remote app!

    The remote application required the devices to be on the same network, and home sharing enabled on Apple TV. The physical remote control would be necessary for the installation if this has not been done already

  • Satellite A300D-158 - unable to connect to the TV via S-video

    I am writing to you, through a translator, as well as the English do not know. And in the forums of the country is not found the answer to this question.

    The problem is that I can't connect to a TV via s-video.
    When a Windows XP connected to a TV with no problems. Now, with Windows 7 x 64, fails to connect.
    Help please.

    FN + F5 does nothing.
    Configure the switch PAL, and so on, also not found.

    Silent.
    As silent as the officials in my country: ((Toshiba)

  • BlackBerry Smartphones has tried to update the device software, now unable to connect to the device via USB

    I tried to update my 8100 to the 4.5 software.  I first updated the desktop to 4.7 software, then tried to update the device, but the process has failed.

    Now, when I open the Desktop Manager it shows not connected to the device.  I can go to the properties of the device mamager and select the balckberry, but when I return to the destop eat it says no device.

    It seems that whatever I do, it does not recognize the usb device.

    The display on the 8100 is company information only text, no graphics or by phone, and it is virtually unusable.

    There are options on the screen for some applications, but if I choose them, it says app not found.

    Is there a way to force an update to it?  Or I poohed this phone?

    Thanks in advance

    Edit:

    I pulled the battery on the device it reboot and tried to return to a former Office Manager Update

    1. unplug BB from USB and PC. Restart the PC turned off completely.

    2. for BB, you'll charge back to the theme that was used on the device when you upgraded, which will normally give you a black and white screen. You must follow the instructions below.

    You will need to use JL_Cmder to wipe the device and then load the operating system on the device. Follow the instructions here:

    http://www.BlackBerryFAQ.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F

    If JL_Cmder does not work, follow this instruction:
    http://www.BlackBerryFAQ.com/index.php/What_to_do_next_if_Jl_Cmder_will_not_connect_and_wipe

  • Unable to connect to the host via VMWare View Security Server 4

    I have installed and configured the VMWare View connection server and can connect to the virtual machine (Windows XP Pro) shareed via the customer to view without a problem. The problem Im having is that I have configured the Security server in my zone demilitarized and authorized the appropriate DMZ ports and the port 80 and 443 to the outside on my DMZ. Access the public URL and he invites me to authenticate what I do and it then publishes my office pool. I click to connect to the shared pool and it says connection for about 5 drops of s and then just my connection. Now, if I go to my security on my DMZ server, I can connect to the thin desktop via RDP.

    Thank you

    eeg3 is correct if you have a direct connection enabled on the broker for connections paired with security server then you would be forced to open 3389 to the outside world since the workstations would try to connect directly to the desktop.    The right way to go forward is to create the replica with disabled direct connection and combine security with this box server.

    If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

  • Z580 help: connect to the TV via a HDMI cable

    I recently had my father the IdeaPad Z580. It is really eager to stream its videos and watch them on TV. I connected it today via a HDMI cable and got really excited when the screen was reproduced on the TV... but then, when I clicked on internet Explorer tile, I got the following error message:

    This application cannot open
    The screen resolution is too low for this application to run.
    Change your screen resolution

    Seems simple enough... but really did not have a clue what to do! Doesn't help that I'm a complete newbie to Windows 8!

    I'd be really grateful if someone here would be able to help / tell me what to do! ^^

    Thanks in advance!

    All of a sudden it works without enaything. In fact, I just do a windows 8.1 update.

  • Satellite A100-784 - connect to the TV via a HDMI cable

    Hi friends,

    I have a Toshiba Satellite A100 - 784 PSAANE. Its a product abandoned now :-( I wonder if I can connect this laptop with the Sony Bravia LED TV via HDMI cable.
    I'm not able to find if the laptop is compatible for it.

    Please help me a way to find a solution to connect the led TV and how to do it? Please also help with the cables needed for the same thing.

    Sorry guys, I'm quite naïve HDMI company.

    Thanks for all the help,

    Kind regards
    Perkins

    Hey Buddy,

    What do not know exactly?

    The laptop has only VGA and S-Video output port but no HDMI port. So that you can t connect the laptop to the TV because you can t connect the HDMI cable to your computer.

    If your TV is VGA or S-video port, you can use this cable. After the connection to the TV, press the key combination FN + F5 to switch between monitors.

  • Unable to connect to the network via a wireless connection.

    cannot connect to a wireless network adapter not connected

    can get Wi - Fi adapters

    Hello

    Do you have any software installed on your computer network monitoring?

    Monitor mode, or RFMON (Radio frequency monitor), allows a computer with a NIC (NIC) to monitor all traffic received from the wireless network. Unlike promiscuous mode, which is also used for packet sniffing, monitor mode allows packets to capture without having to associate with a network access point or ad - hoc first. Surveillance mode applies only to wireless networks, while "Promiscuous" mode can be used on cable networks and wireless. Surveillance mode is one of the six modes of 802.11 wireless cards can function in: Master (acting as an access point), Managed (client, also known as station), Ad - hoc mode, mesh, Repeater, and monitor.

    Limits

    Usually, the wireless adapter is unable to transmit in monitor mode and is limited to a single wireless channel, if it depends on the driver of the wireless card, its firmware and features of all of his chip. In addition, in monitor mode, the adapter does not check to see if the control of cyclic redundancy check (CRC) are correct for packets captured, then some captured packets is maybe damaged.

    If a network monitoring program is running on your computer, the wireless network adapter will be set to follow the fashion, which prevents Windows to connect to wireless networks.

    To connect to a wireless network, close the network monitoring program, or follow the instructions in the program to exit the monitor mode.

    Solve problems, find wireless networks
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

    Let us know if this helps

    Concerning
    Anthony

  • Unable to connect to the printer via ThinPrint error: "serial0: unable to connect to the virtual printer daemon after 25 attempts." The device will be disconnected.

    I started this thread on the debate under of the "Fusion free v2.0.3" but Michael suggested I post this as a new thread, because it turns out that my problem was not due to the much discussed most recent update security Max OS causing ThinPrinting to break.  Whenever I have start up of my (Win XP and Windows 7) VM beta I get the above error message, and therfore cannot take advantage of the ability of merger of ThinPrint print on my printer Mac network.  Michael asked several log files, I have attached 3 in this post and others attached to my next post, so I hope you smart people of VMWare will be able to help me with this problem.  Thanks in advance!

    Ron

    I got a response from ThinPrint with a possible solution - the problem may come from a file/etc/printcap obsolete, which refers to a computer that no longer exists. The DNS lookup may be a delay of 30 seconds and can block the process of thnuclnt. The file/etc/printcap file contains a copy of the configuration of the printer, but it is not necessary for the thnuclnt. It is generally not yet created by OS X by default, but it seems that previous updates to the OS X system or printer drivers can be turned on at any given time. Subsequently, the option got turned off, but the old file was left with outdated information.

    Could you try to rename the file/etc/printcap file and see if it eliminates the delay of 30 seconds? To do this, run Terminal and use the following command:

    sudo mv/etc/printcap /etc/printcap.bak

  • K3 Note connection to the tv via a usb cable.

    My note lenovo k3 does not connect to my LG LED TV with a usb cable, I m trying so many times, but it always shows this usb device not connected.plz help me

    Note from the admin; phone added to the subject type

    K3 phone didn't come with the support of the mhl so I advise you to try to connect your phone to chrome cast device hope this helps.

  • Reinstalled XP and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

    Original title: windows xp.

    reinstalled xp and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

    Hello

    Go to the website of your computer manufacturer > drivers download Section > put your computer model number > operating system > Search adapter network, pilots etc. for her.

    Get graphics, sound while you're there.

    You should always do a reinstallation.

    Use the computer that you use to make the foregoing > download and save in this office > copy of Flash Drive > then install in another computer.

    See you soon.

  • Vista PC is offline, unable to connect to the Internet by LAN or wireless.

    Original title: Vista (Japanese OS)

    My Vista pc is offline (unable to connect to the internet), how install and run the Fixit tool?

    I have read that the English, however, my pc is in Japanese. I can't connect to the Internet by LAN or wireless.
    How can I get the Fixit tool to work on the said pc?
    Help, please!

    Hello

    1. what Fixit tool you try to run?

    2. what exactly happens when you try to connect to the Internet? You receive messages or error codes?

    You can read the following article and check if it helps:

    Windows wireless and wired network connection problems

    You can also read the following article to change the display language:

    Change the display language

    You can use another computer to download the Fix from Microsoft, then use portable storage such as a USB drive, CD, DVD, etc., to carry the Microsoft fix it on your computer.

  • Satellite Pro A10 - WXP re-installed and unable to connect to the internet

    Please help me... I have re-installed Windows XP Home... and now unable to connect to the internet... have also not more of her!
    I went into the Device Manager... in 'other devices' - and it is yellow? mark beside...
    1 / ethernet controller. 2 / multimedia audio controller 3 / PCI modem controller 4 / video...
    They all say "drivers for it are not installed. .... Also, went to "system devices" and find 9 other things that no longer have the drivers installed... said there is also no "audio device" installed!

    My laptop is completely exhausted, or it is better to try to resolve this issue. I'm a fool when it comes to stuff like that... so be gentle with me... what I need to find all the individual drivers and re - install...? BTW... There is no wireless card in the back... (Already checked)...

    Would appreciate any help...
    Thank you

    Hello

    Satellite A10 is a little older model laptop and you can find the drivers in * archives *. go to the [page driver Toshiba | http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp]

    Archive-online Satellite Pro-online Satellite Pro A series-online Satellite Pro A10

    > / ethernet controller. 2 / multimedia audio controller 3 / PCI modem controller 4 / video

    Download and install: 1) Lan Card 4) graph of the card sound 2) 3) Modem driver download also, other drivers if necessary.

Maybe you are looking for