LAN N450 connection through a switch problem

Similar Questions

• Connection through a switch?

  I have a WRT54G V8 router that I want to spend down for better reception.  I want to connect it via my switch EZXS55W V4.2 but I can't seem to make it work.  Do I have to change the settings of the router or is - same not possible?

  Modem high speed---> switch---> router

  michaeloquence wrote:

  I have a WRT54G V8 router that I want to spend down for better reception.  I want to connect it via my switch EZXS55W V4.2 but I can't seem to make it work.  Do I have to change the settings of the router or is - same not possible?

  Modem high speed---> switch---> router

  You can't the front switch the router because it wouldn't give the DHCP issued IP address of this way. The indicated above guy in the correct way to do it.

• connect the m6220 switches stacked to existing Lan infrastructure

  I need to connect two powerconnect M6220 to LAN infrastructure existing.

  The switch of two are configured in the stack.

  Which is the best way to uplink the new switch to the other two powerconnect 5548.

  The old switch are not stacked and bound together by two 10GB Ethernet cable (one of the links is disabled).

  I need to implement the network tolerant to failures, maybe I need to configure the tree covering weight on the two links of 10 GB.

  I use Spanning tree to configure the uplink between the old and the new, too?

  Is there a better alternative? There is another way to prevent the loop network?

  Thanks, Francesco

  You have a few options.

  1. you can simply connect the cables between the M6220 switch stack and the 5548.  Set up a trunk connection which allows for VLAN needed overall.  Tree covering weight until it is enabled on the switch and not off on specific ports connecting the default switches prevent loops and allow the most profitable link to be active, leaving the second connection as an alternative link in a blocking state.

  2. you can configure LAG (aggregation of links).  This is where you configure the individual physical ports in a virtual port channel.  This indicates a covering tree to treat multiple physical ports as a single link aggregated to the other switch.  You will need to have the port at each end of the connection channel mapping. (On each switch).  This allows the same speed but more flow.  To move traffic more.

• Router RV130W + SG92 - 24 Switch problems

  Hey Cisco community,

  I just finished wiring a small office with LAN and connected 24 / SG92. I double checked CAT5 connections with a cable Tester and there is no problem. The wireless is connected to the internet and works fine, however if I try to use a cat5 connection in one of the LAN ports it doesn't seem to work, I get the connection to the router (I can acess 192.168.1.1) but I can't connect to internet through it, am I missing something? If the wireless works very well so in theory the LAN should work too, Ive tried to connect directly to the router and still no luck.

  Current configuration:

  Modem-> router RV130W-of SG92 - 24 Switch-> desktop computers >

  Hope I can fix this problem quickly

  Tim

  can you do ping google.com or any Web site?
  If it is resolved, there must be something wrong with your computer

  Also, as far as I know an RV is also a decent firewall?
  Make sure your policy it allows HTTP, HTTPS, DNS and optionally, ICMP to ping test

• Connect together two switches SRW 2024

  I did some research on this and I'm getting mixed results.  I have 5 Configuration of VLAN, not including the native VLAN 1.  Vlan1 has 1 as untaggged and together the trunk port.  Him is excluded.  VLAN 100 has unidentified port defined on trunk and labeled 1 and 9-12.  VLAN 200 has 1 trunk port and labeled and 2-6 unidentified.  VLAN500 port 1 tag/trunk and 14-20 untagged ports.  VLAN 600 has a port like the trunk but excluded and 21-24 as not tagged. VLAN 700 has port 1 as marked and 7 and 8 as not tagged.  I didn't buy an exact duplicate of the switch, another srw2024 and I want to connect to this existing switch.  Could someone tell me how I can do cela two ways: a way to broaden the VLAN to the second switch and the other with just to add the second switch and be able to create new VIRTUAL networks?  Any help is greatly appreciated!  Thank you =)

  You must create all the VLANS on switches where traffic of this VLAN may occur, either because there is a device connected to VLAN access mode, either because the traffic must travel through the switch. So, in your case, if you create a new VLAN on the second switch probably want to create the same VLAN on the first switch as well and add this new VLAN for the trunk between the first and the second switch port (i.e. make new Member tagged VLAN on the trunk of the ports at both ends).

  Of course, if the first SRW not connected to any other router VIRTUAL local area network or the Internet (e.g. you have a completely closed environment) and that you do not need a VLAN special on one of the switches, there is no need to add the VLAN on the switch or trunk ports. For example, if all the VLAN 100 devices are connected only to the second switch and none of these talks of devices outside, simply configure the VLAN 100 on the second switch because VLAN 100 traffic must never travel to SRW given that there is no device in VLAN 100.

  It is possible, however, generally for clearer network design and a greater flexibility in your facility, I recommend you to run all the VLAN through all switches so that later, when you want to add a device to VLAN 100 on the first switch you would only configure the port rather than begin to implement a new VIRTUAL LAN and configure trunk ports...

• get internet connection through another computer...

  Hello

  I would go straight to the point :)

  I have a desktop running windows vista. I have a normal internet connection through a router that connects to the internet on this desktop computer.

  now, I also have a laptop with windows xp and here is what I do. my laptop's wireless was always bothers me, sometimes it connects, sometimes it doesn't work out... so I saw that there is an Ethernet card installed in the laptop with an Ethernet port.

  My question is this:

  I have a lot of Ethernet cables at home and I was wondering if there is a way to get internet to my laptop via the Ethernet port on my desktop, but without needing the desktop computer to be running, cause I only use my laptop these days and my router is too far to connect from my room. I hope you understand my problem. In theory, I think it's possible to do, but I'm not sure how, so please help me on this one. my laptop also has firewire, but I prefer ethernet for some reason any.

  Thank you

  Hello

  Sorry, but you cannot get a connection via another computer if the computer is off.

  I'm not sure that I understand completely the topology.  However, if the office is connected by cable to a router for Internet connection, you can solve the problem by buying a simple network switch.

  You take the cable from the desktop and connect to the switch. Then you plug the desktop and laptop computer at the switch.

  That this switch network does, it divides a cable to feed many computers.

  Example of a switch that can be connected with a cable to a router and feed 5 computers.

  http://www.Newegg.com/product/product.aspx?item=N82E16833166034-

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• View 5.0 upgrade cannot connect through security on PCOIP server but RDP works very well

  We have improved the sight of 4.6 to 5 and we are no longer able to connect through pcoip via security server. When you connect remotely if you select rdp everything works fine, but pcoip goes to a black screen and then return and error message of 'the connection to the remote computer is done '. Everything worked well in 4.6 before the upgrade and no settings have been changed. Any help would be greatly appreciated... Thank you

  Just had this problem, same solution, external IP had changed its internal IP DMZ, it switched back - totally fixed.

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Lost the remote TCP/IP connection through NOR-MAX

  "" Hi, I try remotely LeCroy WaveRunner 104Xi oscilloscope through "resources VISA TCP/IP" option in Control Panel OR MAX, but the VISA session is lost (0xBFFF00A6) right after I viWrite the '* IDN?" order several times.

  Here's my full configuration process:
  1. install the Passport VISA LeCroyVICPPassportInstaller_1.0.8.exe , LeCroy oscilloscope

  2. setting of the session to follow the instructions (as per joint, LAB_WM827.pdf)

  [by the way, I'm not able to configure the session as "VCIP:'type', I only be able to configure the session asTCPIP0:: 1861:OCKET" ""]
     
      TCP/IP resources VISA-> Create TCP/IP new resource...-> Raw Socket
     Set the IP address: 137.57.96.8 (this IP address is successful to be ping by PC and this address is of course belong to the 104Xi WaveRunner oscilloscope)
  Set the port number: 1861

  3. then, there will be a new resource under "resources VISA TCP/IP". Select this option and 'VISA Open Session'. A dialog box will be retractable to the communication of the instrument.

  4. go to the tab "viSetAttribute", the value VI_ATTR_TCP_KEEPALIVE to VI_TRUE, VI_ATTR_TMO_VALUE the value of 15000.

  * NOR-MAX Version: 3.1.1.3004
  * Connection: The ethernet cable is used through the server (No 1 to 1 connection) of the company,

  "After all this, I send '* IDN? \n"(dans l'onglet viWrite ), it returns the value 0 (which means no error occur) and return 6 counts. " So I try to read a buffer (in the viRead tab), but it send me error timeout (VI_ERROR_TMO). After that, I erase the buffer in viClear. Then, I repeat same steps, this time he (viRead) return me connection lost error (VI_ERROR_CONN_LOST).

  This situation is repeated every time that I reopen it new session. In the meantime, I also doubt that the viWrite did send the command to the oscilloscope or not. The oscilloscope was no response after that I have send "ASET" (WaveRunner 104Xi order for autosetup oscilloscope) through the viWrite tab.

  I am out of ideas now.

  What's my configuration OR-MAX problem? or hardware problem? or a server problem?

  Please advice... need help badly.

  Thanks in advance.

  Hi wcsoh,

  Alan and LeCroy Support here...

  Use the type of connection (LXI).  The problem is that when you use the connection TCP/IP (ACIP) type, you cannot configure the WaveRunner 104MXi as a resource of VISA's TCP/IP in MAX.   Note that MAX is not 'hip' to recognize any instrument type TCPIP, including extended via ACIP LeCroy.  To use LXI, go to utilities > utility configuration... and then to the 'Remote' tab, where you will find the button on the left side of the screen of config to use 'LXI '.  If you don't see this button, you will probably need to update your firmware.

  With the type of connection (LXI), you can automatically find the scope through MAX, enter this amount as a VISA TCP/IP resource and configure an alias as well...  You can also point your web browser to the IP address of the bezel, and you will see a status page with information, including the name VISA always useful resource to use when you configure the scope in MAX.  (Note, however, there is no need to use MAX at all when the connections of VISA to LeCroy oscillloscopes!)

  Here is a link to an application note written by me which deals with the LXI interface, including information about the configuration of MAX to show scope: http://www.lecroy.com/tm/library/AppNotes/LXI/LXI_Interfacing_AppNote.pdf

  Do not hesitate to contact me for any question!

  Best regards

  Alan Blankman

• HP laptop: unable to identify the lan cable connection

  Microsoft Windows [Version 6.3.9600]
  (c) Microsoft Corporation, 2013. All rights reserved.

  Rodriguez C:\Users\anshu > ipconfig/all

  Windows IP configuration

  Name of the host...: fadiga
  Primary Dns suffix...:
  Node... type: mixed
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: Working Group

  Ethernet connection to the Bluetooth 2 network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Device Bluetooth (personal area network)
  #2
  Physical address.... : B0-10-41-80-AF-1E
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Local Area Connection wireless LAN adapter * 5:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Hosted network virtual card
  Physical address.... : B0-10-41-80-AF-1E
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Local Area Connection wireless LAN adapter * 2:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Wi - Fi Direct virtual card
  Physical address.... : B0-10-41-80-AF-1F
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wi - Fi wireless LAN adapter:

  The connection-specific DNS suffix. : Working Group
  ... Description: RT3290 Ralink 802.11bgn wireless adapter
  Physical address.... : B0-10-41-80-AF-1D
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::e809:c01a:618f:7b5a %4 (Preferred)
  IPv4 address...: 192.16.137.4 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Saturday, June 11, 2016 08:56:13
  End of the lease...: Wednesday, June 15, 2016 12:56:15
  ... Default gateway. : 192.16.137.1.
  DHCP server...: 192.16.137.1.
  DHCPv6 IOOKING...: 78647361
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers...: 10.10.2.2.
  192.16.137.1
  NetBIOS over TCP/IP...: enabled

  Ethernet Ethernet adapter:

  The connection-specific DNS suffix. :
  Description...: Realtek PCIe FE Family Controller
  Physical address.... : 14-58-D0-C5-74-1D
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::3070:15bf:b1ee:daab %3 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.218.171 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DHCPv6 IOOKING...: 51665104
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP...: enabled

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card adapt 6TO4 tunnel:

  The connection-specific DNS suffix. : Working Group
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2002:c010:8904:c010:8904 (Preferred)
  ... Default gateway. :
  DHCPv6 IOOKING...: 704643072
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers...: 10.10.2.2.
  192.16.137.1
  NetBIOS over TCP/IP...: disabled

  Tunnel adapter ISATAP.workgroup:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : Working Group
  ... Description: Adapter Microsoft ISATAP #5
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {74914F29-E819-4DEB-8CC2-D37CBFD70F3B}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #6
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Rodriguez C:\Users\anshu >

  On the lan cable connection, it says as unidentified network.

  That's what I have to type the command ipconfig/all.  I tried to reinstall drivers recvoery as Manager, but no results. It worked without problem until now

  @anshu645

  Home networks typically use a form any of 192.168.x.x

  For example:

  192.168.1.14

  Found in your example:

  192.16. 137.1

  Also found:

  Autoconfiguration IPv4 address. . : 169.254.218.171

  +++++++++++++++++++++++++++++++++++++++++++++

  I suspect that the installer with your home network router is misconfigured and the network can't find a viable (useful) DNS address to use for the purpose of ISP Internet Service (ISP) connection.

  Please see the following:

  HP PC - troubleshooting wired home networks (Windows 8)

  HP PC - Troubleshooting wireless network and Internet (Windows 8)

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• EA6500 only shows no device connected to the switch of working group 5 ports

  I just replaced a defective Linksys e4200 with an ea6500.  After assistance by phone, I got to the top and work, but only one computer on my LAN is not displayed.

  I connected an 8 port 10/100 switch Linksys my 4200, and my wife's computer was connected to that.   The computer displays the IP as 192.168.1.133 and it is connected to the internet with my router again.  But the ea6500 does not show a device with the ip address.  Instead, he shows what he calls a network with the IP 192.168.1.130 device.

  How can I see the devices connected to the switch 5 ports and determine which ip addresses, they have been assigned?

  I use a switch with my network with a router EA and it shows the devices correctly. Turn off the computer which does not appear in the list of devices and check to see if any device will appear as offline adter who. Remove from the list of devices, and then restart the router. Once the router is ready, open the page of the router again and turn on the computer and check if it will be detected correctly. I hope this helps.

  Edit: Check and make sure you have the latest firmware loaded. Otherwise, update the firmware and do a reset after the update of the firmware. Check your list of devices after that.

• Allow other users to connect through my internet connection of mobile phones.

  Quite simply, I'm setting up my xbox live to run through my internet connection of mobile.

  When I select the check box to allow other users of the network to connect through this computer's internet connection it turns off immediately, so is not enabled.

  I tried disabling the firewall etc to see if it limited the ability of sharing, but it did not work.

  Any information or help would be greatly appreciated.

  Hi Stewart,
   
  Please go through the article below which will help you to connect to windows live using your internet connection for your laptop.
  How to connect your Xbox 360 wired controller to a computer running Windows
  http://support.Microsoft.com/kb/906347

  Please also see the link below. This could help you.
  http://support.Microsoft.com/kb/978618

  If the problem persists, I suggest that question you post you to Xbox forums.
  Xbox support

  http://forums.Xbox.com/xbox_forums/xbox_support/default.aspx

  http://www.Xbox.com/en-us/forums
   

• Received my brother in laws laptop cannot connect wireless, although I can of my own laptop. Trying to connect through the new laptop, I do not see even my own network.

  Received my brother in laws laptop cannot connect wireless, although I can of my own laptop. Trying to connect through the new laptop, I do not see even my own network! What I'm missing here? I'm sure it's maybe something simple, but for the life of me! (When my brother-in-law used this computer, he only uses it through dialup (!), he lives in a remote area). With the help of Vista, and when 'Management of connections' I see my network...

  original title: cannot connect wireless

  Hello

  ·         You get the error message?

  Method 1:

  I suggest you update the drivers for hardware connected to your computer on the Web site of the manufacturer check if it works.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Also, follow the steps in troubleshooting section and check if that helps:

  In the Windows wireless network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows

  Check out these links and check if that helps

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  See also:

  Solve problems with computers not appearing is not in the network map

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map

  Hope this helps

• If my desktop pc is connected through CATV cable, I use the wireless connection?

  We have a router that connects two laptop computers, a smart phone and smart TV, a Kindle reader and a printer.

  I want to know is so that desktop shows a "wireless network connection", I actually use this connection if this computer is connected through a CATV cable? Specifically, if I disconnect in that regard, maybe would I win any speed for this computer or laptop computers that are located in different parts of the House?

  And if so, how can I fix it so that it does not automatically each time connect that I boot?

  Thanks for your advice.

  It seems to me that you have a wireless router with many connected devices, including a desktop PC, and you want to know if forcing the PC being used a wired connection to the router, instead of a wireless connection, will increase speed or ease of use for one of your devices?

  Short answer, probably yes, and it should not hurt anything.

  Wireless network connections are all just more finicky than the wired connections. Without knowing the details of your router, I can't do any insurance policy, but reducing the pressure on your wireless radio components and its replacement by the PC with a wireless connection wired should not hurt anything and could help.

  I guess CATV here means a type of wired network cable CAT-5 cable? If it's just a "CAT 5" cable, he'll only go 100 Mbps, which might be slower than your wireless router. However, 100 Mbps is probably faster than your internet connection at home (your speed of the router to the outside world), so it should be good. If it's a "CAT-5e" cable, so no problem.

  To disable your wireless connection on the PC, go to control panel-> Device Manager command. You will get a window with a list of all the hardware devices on your computer, listed by category. A category must be "Network adapters" or something similar. Expand this category by clicking on it and find your wireless card (something something Wifi or wireless network card). Right-click, and then click on disable. Now your computer will be able to connect with the wired connection. When you want to cancel the process, simply repeat these steps and you will find that 'Disable' has been replaced with the option 'enable '.

• I can't confirm my new pc as my trusted pc. I am told to confirm by connecting through my old reliable pc. Error: "you cannot add a reliable PC now."

  original title: cannot confirm reliable pc

  I can't confirm my new pc as my trusted pc. I am told to confirm by connecting through my old reliable pc. My old pc 'confidence' problem no longer exist. I can add also, not a new pc, "confidence". When I try, I get the following message is displayed:

  You cannot add a reliable PC now

  To add a reliable PC to your account, you must have installed Windows Live Essentials. Install Windows Live Essentials

  I have installed Windows Live Essentials.

  Thanks for all the solutions.

  I got the message from Windows Live Essentials do not installed when I didn't sign my Live ID in WLMail.

  You have a confirmed alternate email or SMS phone number address?