LAN on PIX 501 interface

Similar Questions

• IPSec VPN pix 501 no LAN access

  I'm trying to set up an IPSec VPN in a basic small business scenario. I am able to connect to my pix 501 via IPSec VPN and browse the internet, but I am unable to ping or you connect to all devices in the Remote LAN. Here is my config:

  : Saved

  :

  6.3 (3) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  nameif ethernet0 WAN security0

  nameif ethernet1 LAN security99

  enable encrypted password xxxxxxxxxxxxx

  xxxxxxxxxxxxxxxxx encrypted passwd

  host name snowball

  domain xxxxxxxxxxxx.local

  clock timezone PST - 8

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  No fixup not protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  acl_in list of access permit udp any any eq field

  acl_in list of access permit udp any eq field all

  acl_in list access permit tcp any any eq field

  acl_in tcp allowed access list any domain eq everything

  acl_in list access permit icmp any any echo response

  access-list acl_in allow icmp all once exceed

  acl_in list all permitted access all unreachable icmp

  acl_in list access permit tcp any any eq ssh

  acl_in list access permit tcp any any eq www

  acl_in tcp allowed access list everything all https eq

  acl_in list access permit tcp any host 192.168.5.30 eq 81

  acl_in list access permit tcp any host 192.168.5.30 eq 8081

  acl_in list access permit tcp any host 192.168.5.22 eq 8081

  acl_in list access permit icmp any any echo

  access-list acl_in permit tcp host 76.248.x.x a

  access-list acl_in permit tcp host 76.248.x.x a

  allow udp host 76.248.x.x one Access-list acl_in

  access-list acl_out permit icmp any one

  ip access list acl_out permit a whole

  acl_out list access permit icmp any any echo response

  acl_out list access permit icmp any any source-quench

  allowed any access list acl_out all unreachable icmp

  access-list acl_out permit icmp any once exceed

  acl_out list access permit icmp any any echo

  Allow Access-list no. - nat icmp a whole

  access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

  access-list no. - nat ip 172.16.0.0 allow 255.255.0.0 any

  access-list no. - nat permit icmp any any echo response

  access-list no. - nat permit icmp any any source-quench

  access-list no. - nat icmp permitted all all inaccessible

  access-list no. - nat allow icmp all once exceed

  access-list no. - nat permit icmp any any echo

  pager lines 24

  MTU 1500 WAN

  MTU 1500 LAN

  IP address WAN 65.74.x.x 255.255.255.240

  address 192.168.5.1 LAN IP 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool pptppool 172.16.0.2 - 172.16.0.13

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global (WAN) 1 interface

  NAT (LAN) - access list 0 no - nat

  NAT (LAN) 1 0.0.0.0 0.0.0.0 0 0

  static (LAN, WAN) 65.x.x.37 192.168.5.10 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.36 192.168.5.20 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.38 192.168.5.30 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.39 192.168.5.40 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.42 192.168.5.22 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.43 192.168.5.45 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.44 192.168.5.41 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.45 192.168.5.42 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.46 192.168.5.44 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.41 192.168.5.21 netmask 255.255.255.255 0 0

  acl_in access to the WAN interface group

  access to the LAN interface group acl_out

  Route WAN 0.0.0.0 0.0.0.0 65.x.x.34 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  NTP server 72.14.188.195 source WAN

  survey of 76.248.x.x WAN host SNMP Server

  location of Server SNMP Sacramento

  SNMP Server contact [email protected] / * /

  SNMP-Server Community xxxxxxxxxxxxx

  SNMP-Server enable traps

  enable floodguard

  the string 1 WAN fragment

  Permitted connection ipsec sysopt

  Sysopt connection permit-pptp

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  client configuration address map mymap crypto initiate

  client configuration address map mymap crypto answer

  card crypto mymap WAN interface

  ISAKMP enable WAN

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup myvpn address pptppool pool

  vpngroup myvpn Server dns 192.168.5.44

  vpngroup myvpn by default-field xxxxxxxxx.local

  vpngroup split myvpn No. - nat tunnel

  vpngroup idle 1800 myvpn-time

  vpngroup myvpn password *.

  Telnet 192.168.5.0 255.255.255.0 LAN

  Telnet timeout 5

  SSH 192.168.5.0 255.255.255.0 LAN

  SSH timeout 30

  Console timeout 0

  VPDN group pptpusers accept dialin pptp

  VPDN group ppp authentication pap pptpusers

  VPDN group ppp authentication chap pptpusers

  VPDN group ppp mschap authentication pptpusers

  VPDN group ppp encryption mppe 128 pptpusers

  VPDN group pptpusers client configuration address local pptppool

  VPDN group pptpusers customer 192.168.5.44 dns configuration

  VPDN group pptpusers pptp echo 60

  VPDN group customer pptpusers of local authentication

  VPDN username password xxx *.

  VPDN username password xxx *.

  VPDN enable WAN

  dhcpd address 192.168.5.200 - 192.168.5.220 LAN

  dhcpd 192.168.5.44 dns 8.8.8.8

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd enable LAN

  username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

  username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

  Terminal width 80

  Cryptochecksum:xxxxxxxxxxxxxxxxxx

  : end

  I'm sure it has something to do with NAT or an access list, but I can't understand it at all. I know it's a basic question, but I would really appreaciate help!
  Thank you very much
  Trevor

  "No. - nat' ACL doesn't seem correct, please make sure you want to remove the following text:

  do not allow any No. - nat icmp access list a whole

  No No. - nat ip 172.16.0.0 access list allow 255.255.0.0 any

  No No. - nat access list permit icmp any any echo response

  No No. - nat access list permit icmp any any source-quench

  No No. - nat access list permit all all unreachable icmp

  No No. - nat access list do not allow icmp all once exceed

  No No. - nat access list only allowed icmp no echo

  You must have 1 line as follows:

  access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

  Please 'clear xlate' after the changes described above.

  In addition, if you have a personal firewall enabled on the host you are trying to connect from the Client VPN, please turn it off and try again. Personal firewall of Windows normally blocks the traffic of different subnets.

  Hope that helps.

• Ping inside the interface on a Pix 501 from outside the network

  All the

  I have a Pix 501 firewall at a remote site with an IPSEC tunnel established at HQ. We have an analysis tool which remote sites for us let proactively pings know when a site crashes. I want to set up this ping the inside interface of the Pix tool as I can with 871 routers; However I can't configure the Pix to allow ICMP inside interface. I know by default that the Pix does not allow ICMP to the opposite interface and I was wondering if someone could help me with a configuration that will allow this? I enclose my configuration of the pix!

  Thank you

  Brian

  Hello

  By raising the ordering tool, it seems that the 'management-access' command was introduced in version 6.3

  I recommend spending at 6.3 If you can.

  Federico.

• Configure the PIX 501 for IDS

  I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

  IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

  If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

  You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

• PIX 501 and VPN Linksys router (WRV200)

  I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other

  sites. Asked me to connect these routers Linksys firewall PIX via the VPN.

  According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.

  Key exchange method: Auto (IKE)

  Encryption: Auto, 3DES, AES128, AES192, AES256

  Authentication: MD5

  Pre Shared Key: xxx

  PFS: Enabled

  Life ISAKMP key: 28800

  Life of key IPSec: 3600

  The pix, I installed MDP and I tried to use the VPN wizard without result.

  I chose the following settings when you make the VPN Wizard:

  Type of VPN: remote VPN access

  Interface: outside

  Type of Client VPN device used: Cisco VPN Client

  (can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)

  VPN clients group

  Name of Group: RabyEstates

  Pre Shared Key: rabytest

  Scope of the Client authentication: disabled

  Address pool

  Name of the cluster: VPN - LAN

  Starter course: 192.168.2.200

  End of row: 192.168.2.250

  Domain DNS/WINS/by default: no

  IKE policy

  Encryption: 3DES

  Authentication: MD5

  Diffie-Hellman group: Group 2 (1024 bits)

  Transform set

  Encryption: 3DES

  Authentication: MD5

  I have attached the log of the VPN Linksys router VPN.

  This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.

  Thanks for your help!

  Hello

  Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.

  Let me know.

  See you soon,.

  Daniel

• PIX 501 establish IPSEC connection, but no data transmission

  Hi all

  I had a strange problem with a cisco 501 pix connected cisco 3000 vpn concentrator remotely.

  The pix is configured for the remote access session to the hub. The problem is that when I do a ping the ipsec tunnel is established and bytes will be transmittet but it's no or few bytes are received by the hub.

  So I can't? t ping Lan behind the pix.

  I don't know what could be the probelem. The two phases are created.

  What can be the problem?

  Attached to the PIX config.

  Best regards

  Kai

  6.3 (4) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxx

  passwd xxx

  host name

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside ip access list allow a whole

  inside_access_in ip access list allow a whole

  pager lines 24

  MTU outside 1456

  MTU inside 1456

  IP address outside pppoe setroute

  IP address inside 123.0.0.200 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 123.0.0.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  outside access-group in external interface

  inside_access_in access to the interface inside group

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 123.0.0.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet 133.0.0.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoe_group request dialout pppoe

  VPDN group pppoe_group localname *.

  VPDN group ppp authentication pap pppoe_group

  VPDN username *.

  password *.

  vpnclient Server 111.x.x.200

  vpnclient mode network-extension-mode

  vpnclient vpngroup vpn password *.

  vpnclient user_name password pix *.

  vpnclient enable

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  you are the ping of the network behind the hub to devices behind the PIX?

  You can then check if you see the data received on the end of PIX? You can check that by issueing the command

  Crypto ipsec to show his

  It will tell you by his how many bytes have been received / sent.

  If you see bytes received and sent and they will increase after you issue a ping (usually the increase is 4 packs), you know this isn't the pix, but something as nat-traversal that blocks the return circulation.

• VPN site-to-site between two PIX 501 with Client VPN access

  Site A and site B are connected with VPN Site to Site between two PIX 501.

  Also, site A is configured for remote access VPN client. If a remote client connects to Site A, it can only get access to the LAN of Site A, it cannot access anything whatsoever behind PIX on Site B.

  How is that possible for a VPN client connected to Site A to Site B?

  Thank you very much.

  Alex

  Bad and worse news:

  Bad: Not running the 7.0 series PIX cannot route traffic on the same interface, the traffic is recived. Version 7.0 solves this ipsec traffic.

  Even worse: PIX 501 can not be upgraded to 7.0...

  A couple of things to think about would be the upgrade to hardware that can run the new IOS or allowing a VPN R.A. on site B.

  HTH Please assess whether this is the case.

  Thank you

• Pix 501 problem

  I can not configure a pix 501 as a firewall, I need to know if it comes with a default configuration. I connect the PIX of the LAN and it start´s to DHCP each machine on the network with no problem, but none of the user´s can access the internet.

  I need to know what to do to get access to internet protection and network security.

  Where can I go to configure the Pix, if I really need to configure it!

  Hi... basically, you need the following basic steps to access your internal users to the internet

  If you use 6.3 (5) PIX

  interface ethernet0 100full

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  inside_access_in ip access list allow a whole

  inside_access_in access to the interface inside group

  NAT (inside) 1 access-list inside_access_in

  Global 1 interface (outside)

  NOTE: with the config ablove room your internal users will have FULL access to the internet. If you want to restrict access to only http, https, ftp, dns, etc then you need to change the access list for something like that...

  inside_access_in list access permit tcp any any eq www

  inside_access_in list access permit tcp any any eq 443

  inside_access_in list access permit tcp any any eq ftp

  inside_access_in list access permit tcp any any eq 53

  inside_access_in udd allowed access list any any eq 53

  I hope that helps... Rate if he does!

• Help the PIX 501 - cannot access startup.html

  I'm new to the network and has received a job to configure the PIX 501 firewall.

  The fact is:

  We use IP table rules as a firewall on a linux machine. My pc is connected to a switch. So I use the yellow network cable to connect the port of the Pix 501 0 to the port in the switch. Then I disconnect my pc of swich cable and plug into the port of the Pix 501 1.

  My pc is to use a static ip address before. I try to change to automatically get an IP address, but it will not work. So I changed the setting and use the IP address originally. Pop up message network connection icon says that the local connection is enabled. But when I try to ping 192.168.1.1, request time-out. Also I can't acess the https://192.168.1.1/startup.html.

  I have a look at Books Online cisco and shootings of disorder, but most of them talk about the configuration or more advance features. I'm still on the very basic level to try to connect to the firewall.

  I hope someone can help me. All ideas and questions are welcome. Thank you.

  Your IP address should be fine. You do not want to have the PIX connected to your local network, even if you have the Linux firewall as well as this will cause a conflict. Keep the PIX the LAN for now. Your DNS configuration will have no effect because the url you are trying to reach is based on the IP address and not the domain name if your PC has nothing to look for.

  You have to check the cable that you use - if your PIX has only an 'inside' interface, then you must use a crossover cable. If he has four so it's built in switch for a straight cable will be fine. Is what PIX model?

  After checking the cable - see if you can console in the firewall - use the blue cable that came with the PIX and set up a connection (hyper terminal) terminal with the help of 9600, 8, no 1. If you can console and then you can stick in a basic configuration you can get.

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Adding a pix 501 VPN 2

  Hello.. I am beginner in this kind of things cisco...

  I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

  Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

  Outside_map map (ERR) crypto set peer 200.20.10.3

  WARNING: This encryption card is incomplete

  To remedy the situation even and a list of valid to add this encryption card

  Hi garcia

  for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

  for configuration, you can go through the URL below... It has all the details on IPSEC config:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• How to configure the PPPoE on PIX 501?

  Mailto: [email protected] / * /

  MSN: [email protected] / * /

  According to the below URL Cisco TAC:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00801055dd.shtml

  but I always failed. And my PIX 501 Configuration noted below:

  pixfirewall # write terminal

  Building configuration...

  : Saved

  :

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxx

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside pppoe setroute

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1

  Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoex request dialout pppoe

  Cisco localname VPDN group pppoex

  VPDN group ppp authentication pap pppoex

  VPDN username xxxx password *.

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  [OK]

  See the pixfirewall version #.

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Thursday 19 March 03 11:49 by Manu

  pixfirewall until 58 mins 6 dry

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 000b.fd58.886b, irq 9

  1: ethernet1: the address is 000b.fd58.886c, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: 50

  Throughput: unlimited

  you have all the debugging logs?

• Opening of port 22 in PIX 501

  I would like to access my PC location xyz. How can I open port 22 access to my pc. I use pix 501.

  Can anyone provide commands to open the port so that I can access my pc.

  Thank you

  totally agree because only 3 commands are needed.

  list of allowed inbound tcp access any eq 22

  public static tcp (indoor, outdoor) interface 22 22 netmask 255.255.255.255 0 0

  clear xlate

  However, all of these commands are missing in the config you have posted.

• PIX 501 does support proxy ARP?

  Hello

  I would like to know if it is possible to publish a proxy arp some public address on the external interface of a PIX 501.

  What is the command I should use?

  Thank you

  Hello

  proxy ARP is performed automatically when you use the 'static' command to bind the IPaddress private an internal server to a public IP address.

  Kind regards

  Tom

• VPN with PIX 501

  Help!

  I'm trying to set up VPN on my PIX 501. I have no experience of the PIX and have no idea where to start!

  Any help will be greatly appreciated.

  Thank you

  Bennie

  access list allow accord a

  where is the name of the access list that you applied the entrants to your external interface. You may also allow accord coming out, if you have a list of incoming configured access to your inside interface.