LAPAC 1750

Similar Questions

• LAPAC 1750 - radiation pattern

  Hello

  can someone please provide me with information on the radiation of LAPAC 1750 Access Point diagram?

  Instead of using trial and error that I would sooner plan the deployment of units based on wireless fingerprint, so I can get appropriate spacing etc.  The information that I found that I can't decide if the unit is best ceiling or wall.  Is the unit of directional radio frequency signals come only from the front, or they go through the back too?  This could have repercussions on the interference seen on the floors above the unit.

  Thank you

  Pete

  Answer:

  No documentation but the ceiling is preferable, given that the dipole is used.

• LAPAC 1750 PRO - rename associated Clients / Stations

  Hi, just a 1750 LAPAC PRO and searched the manual, but I can't find a solution to my 'problem '.

  In the @ status and Statistics Web interface / associated Clients, I can see a lot of MAC addresses - is there a way I can rename them to something real, like the iPhone 6, iPad Mini, Macbook Pro, etc.. ? !

  Its kind of hard to remember what MAC address belongs to which device ;-)

  I don't think you can label these MAC.

  I recommend their labelling in the booking section of IP for the DHCP server on your router or network card it is; If it has these characteristics.

• How can I fix a problem with my Dell Inspiron 1750 internal speaker?

  I started having problems with the internal speakers on my Dell 1750. Everyone knows about this problem? Is there a solution?

  Hello

  For hardware problems, you will need to contact the manufacturer of the computer. Here is a link for your convenience.

  Dell Contact technical support: http://support.dell.com/support/topics/global.aspx/support/dellcare/contact_technical_support?c=us&cs=19&l=en&s=dhs& ~ ck = mn

  Concerning

• Compaq armada 1750: I am looking for a power supply

  I got this from a friend and thought it might be a good start for a grandchild to learn to use a computer, and it has no power to provide, so I'm looking to find a.

  hoglie wrote:

  I got this from a friend and thought it might be a good start for a grandchild to learn to use a computer, and it has no power to provide, so I'm looking to find a.

  Here are the specifications pdf for IT... you will probably find the info on that for the AC adapter.

  http://WWW8.HP.com/h20195/v2/GetPDF.aspx/c04282128.PDF

  Also read this?

  PC series laptop Compaq Armada 1750

  https://h20566.www2.HP.com/portal/site/hpsc/public/PSI/manualsResults/?sp4ts.Oid=96222&AC.admitted=1445452974776.1123376534.199480143

• Laptop Inspiron 1750 with Windows Vista. Windows 7 upgrade query

  Hello. I bought a laptop computer Inspiron 1750 in Nov 2009 with Windows Vista. Now, I need to upgrade Windows 7. Would I get a free window upgrade. Reference Dell provides a free upgrade? Thank you

  That the system was sold after the release date of Windows 7 and you should have had Windows 7 pre-installed... otherwise you were entitled to a free upgrade... were, however, intends to take advantage of it between 2009 and 2010.

  Dell Windows 7 OEM System locked preinstallation work on this model should however you have Legacy BIOS revision A06. See here for more details:

  http://dellwindowsreinstallationguide.com/Windows-7-SP1-ISO-download/

  After clean installation Windows 7 OEM with system drivers, you should immediately perform an inplace upgrade to Windows 10 using the tool of creation of media:

  http://dellwindowsreinstallationguide.com/upgrading-to-Windows-10/

  The free update from Windows 7 to Windows 10 is only available for the next 10 days.

• Dell 1750 upgrade hard drive

  A Noob so please bear with me to be Noob-ish.

  My 250 gig Sata in my dell aging 1750 Inspirion finally gave up the ghost and died (RIP), do not make Jeremy by that I buy a 640 GB Toshiba Sata Drive, piece of cake to fit, 4 screws, and work has been done, reassembled. And went to reinstall the OS (Win 7), now get a black screen with no boot or the interial drive, which I am slightly confuddled with.

  I get a device bootable No. strike f1 to reboot, F2 for Setup Utility or F5 to run onboard diagnostics, (which I've done), now I'm lost...

  Please help before I'm going Mad!

  Osprey,

  Thanks a lot for your comments, but I have remedied this problem, took 24 hours to solve, but I got in the end, with the need to order a CD of replacement, which I have, as I suspected that it was not a mistake with the optical drive (false positives), it is simply because it was a replacement for my replacement of 250 gig SATA drive now its works very well, as I type this response on my laptop with the new drive.

  Have a good day Sir!

• Dell Inspiron 1750, Windows 7: HL-DT-ST DVD +-RW GT10N not working after critical updates from MS

  I'm having a problem with my Player DVD - HL - DT - ST DVD +-RW GT10N.  I have a Dell Inspiron 1750, Windows 7.

  It was working fine, then after 3 critical updates from MS, it stopped reading/writing on the DVD player.  The only way I can access the DVD (read or write) is to restart.  A subsequent loading of different or even the same DVD finished with the issue of not being able to recognize the DVD.

  When I click on the properties of the DVD drive in Device Manager, it clocks.  However, after a reboot, the properties has worked well and said that the driver does not work properly.

  I got to the period before 1st update was installed and the DVD player worked as before.  However, Ms. downloaded the same (I assume) updated critical shortly after.  Low and behold, the DVD player does not work yet.

  The MS CD/DVD patch could not fix.

  I also tried UpperFilters/LowerFilters regedit deletions, but it is impossible to find these entries (http://support.microsoft.com/kb/982116 > HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}).  Thank you Osprey4 for your help continues.

  I hope someone can help me.

  Thank you

  Duane.

  Open Device Manager, right-click on the component, and then select uninstall.

• My network card on my Inspiron 1750 has stopped working suddenly.

  My network card on my Inspiron 1750 has stopped working suddenly. I left the computer, while I was working online, went for about 2 hours, and when I came back, I wasn't online more. I can't reconnect to the internet. I was on the phone with the cable operator for two hours Tuesday night, and they said that I probably need an updated adapter. My computer tells me it is good, but then again, I can't connect to the internet to check. I tried an ethernet connection, but it is not recogniziing either. What should I do?

  Hi Joyce,

  Thanks for posting your query in Microsoft Community.

  I understand from the description of the issue that you are facing problem with Internet connection in Windows 7. I will certainly help you in this matter.

  Were there any changes made to the computer before the show?

  Please follow the steps in the link.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-in/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Using the windows-related issues feel free to post on the Microsoft Community Forum.

• Impossible to get any OS to install PowerEdge 1750 Server

  I'm having some trouble with that and it makes me nuts. It's the 1st Rackmount Dell I worked on. Other then that I was working on a tower. But the part that I did not do anything with the SCSI hard drives is.

  So maybe someone here can help me. I got a Dell PowerEdge 1750, 2 Maxtor 36 GB SCSI disks in there. The server was using RAID mirror the primary drive before being erased and replaced. So now, the server must be configured with Linux and it does not matter if drivers are reflected in the RAID at all.

  So I tried to install Ubuntu server OS and he repeated to me that it cannot find the drivers for the drives. I tried a few drivers here at DELL who have been to Red Hat and it did not work.

  Then, I tried a copy of Red Hat Linux 8.0 and had the same problem that Ubuntu has given me.

  Then laughing, I tried a copy of Windows XP Home Edition who was sitting by a former Workstation. Same problem, Windows could not find the hard drives. I have download the drivers PERC 4/Di windows server 2000 and 2003 (x 84). Tried loading to see if pilots would allow me to install the OS or not. Never worked.

  Finally try, I popped a copy of Windows Server 2003 R2 Enterprise Edition in and he had the same problem as XP, so I pop the drivers PERC 4/Di and selected the driver for Windows Server 2003 and it has yet to find the hard drives.

  What I am doing wrong?

  NEWS POST:

  Integrated server 1.80 Firmware revision management

  Review from the primary backplane Firmware 1.01

  PowerEdge Expandable RAID Controller BIOS B109 February 18, 2003

  PERC 4/Di Standard FW 4.04

  0 logical drives to the host adapter

  Or logical drives 0 managed by the BIOS

  Broadcom NetXtreme managed by BIOS Boot Agent V7.0.3

  I don't know if this noraml or not, I think that it funny that he finds the 0 logical drives, but when you go into the configuration both appear in there.

  PERC does not support non - RAID JBOD, so if you want mirrored or not, you must configure the drives in the PERC BIOS (CTRL-M)... or put it turns off and only use the system SCSI controller.

  If you want to use as separate readers readers / person, you must configure each disk in a single drive RAID 0.

  If you want to disable RAID and used in SCSI mode only, so you need to start on the configuration of the BIOS (F2), embedded devices, and Embedded RAID SCSI value active.

  The fact that the POST said 0 logical drives found indicates that the disks are not configured - don't forget, readers must be configured in a sort of table before they can be used by the operating system.  So it must show at least a logical drive before installation can never be successful.

  Once the RAID is set up, you will need to worry about drivers.

• Dell Poweredge 1750 - no boot device

  Hi, I am totally new to the servers and have bought a second hand PE1750 off ebay so that I can learn how it works.

  The vehicle currently has no operating system on it and the BIOS is always A06.

  I downloaded A12 and try updating the bios.

  (1) is it possible to update the BIOS from the BIOS?

  (2) I don't have drive C: and CDROM in boot sequence via the F2 Setup utility.

  (3) no found boot device.

  (4) I have 1 configured logical drive

  (5) there is no option to boot from USB

  can anyone help me get this site up and running please?

  Dave

  cosmic_jester_uk

  is it possible to update the BIOS from the BIOS?

  Not from the "BIOS", per se... but you can start a utility to update update the firmware of the system (including the BIOS).

  1750 does not support the boot on USB. You will need to boot from the CD/DVD (or PXE or diskette) for what you intend to do.

  You can use SUU (Server Update Utility):

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=GHC9V&FILEID=2731109500&osCode=WNET&ProductCode=PowerEdge-1750&LanguageCode=en&CategoryID=SM

  First start in GDPS (systems management tools and Documentation) which requires:

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=P8V4X

  Or you can use the repository Manager:

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=X5YK8

  OR you can install an operating system and update the firmware of the system of the operating system.

• Inspiron 1750 lcd cable

  I bought a new lcd cable for an inspiron 1750 that does not display on screen, but displays correctly when an external monitor is connected to the vga port. The screen light up (backlights). Now that I installed the new cable, the display on the laptop is not even light to the top more.

  My question is, "what is the difference between, or is there a difference between the part # G600T, 0G600T, 50.4CN05.101 and G600T, 0G600T, 50.4CN05.001." My old cable number is the last, and the one I bought is the first. Could it be the problem? Help, please.

  The cables are the same - so assuming have not two cables defective (unlikely), it is much more likely, that the motherboard itself is defective, not the cables - assuming that the LCD is working (to check this, hold down the key of D through power until you see in alternation of solid - color screens if you get that far the screen is OK).

• Problem with old PE 1750

  Also has anyone seen a situation where a PowerEdge 1750 refuses to accept a full 8 GB of RAM? I have a system that's been completely upgraded BIOS A12 level (later), and everything else works correctly. He started 2 GB (4 512 k sticks) and I swapped the first Bank for 2 GB sticks to 5 GB. That worked fine, but then swap Bank 2-2x2gb (maxing out from the machine to 8 GB) causes the machine resets itself automatically as soon as he finishes the rotation to the top SCSI drives.

  I tried several sets different modules, all registered/ECC and the correct specification, but none works. There seems to be nothing wrong with the Bank 2, as I can put in there 2 GB modules with 512 k in Bank 1 and the system boots. It's just that it fails to 8 GB (Windows 2008 32-bit is installed). I heard from one source the USB built-in to support BIOS no definition could help, but that didn't work.

  Any ideas appreciated.

  Hi, I had the same problem and have a solution.

  In the bios there is a setting of redundant memory slot.  By default, it is set to disabled.  Setting to enabled the server start properly and do all 4 slots available to the operating system.

  I am able to run Windows Server 2008 (x 86) Enterprise with 8 GB of ram.

• Huawei E 1750 drivers

  where can I find all the drivers for huawei E1750 with compatible to windows XP SP2 drivers?

  Hi Nishu_Ran,
   
  Contact the Support of Huawei for drivers for the modem:
  Support of Huawei
   

  See the link below for more information on the update of the driver.

  How to manage devices in Windows XP

• How to cut the touchpad on my dell inspiron 1750

  I use a wireless mouse but cannot NOT cut my touchpad HELP

  Hello

  Check with the manufacturer of system support, documentation in line, and/or forums he has probably shortened that
  enable and disable the touchpad functions.

  Check the Notification (Systray) area for a TouchPad control utility.

  Also check the control - Mouse - touchpad settings panel.

  Disable the Touchpad of your laptop Dell
  http://www.killertechtips.com/2009/04/30/disable-touchpad-Dell/

  On some models, you hold down the Fn key and press the F key that has a symbol of top to toggle TouchPad the TouchPad
  MARKET.

  Dell support
  http://support.Dell.com/

  Drivers and Support technical
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.