laptop connected hp g56 to toshiba regza tv but no sound... Help, please! : )
Hi, I am looking to connect my laptop g56 to my tosiba tv regza.
I managed to get the fine photo using a vga cable but with no sound. After a bit of research and asking questions, I was told to do a plug to rca (red and white) cable, connect the plug to my laptop headphone plug and the rca to the corresponding ports of the TV. Done that and there is still no sound coming out of the tv!
What I need to download a special driver or something to make the sound go out the TV or is it better to go buy a hdmi cable?
Any advice would be really appreciated!
Hello
A VGA output is only able to carry a video signal - I strongly suggest that you forget about yourself and get an HDMI cable to connect to your TV. There is no need to buy a high-end cable, just a stanadard HDMI cable is very well - I never found no difference in the quality of output.
Kind regards
DP - K
Tags: Notebooks
Similar Questions
-
Adobe indicates that I paid, but I am unable to use it on my computer to convert files in word on my mac files adobe. When I connect to my online account, it shows my products two adobe, but it says that I have not saved. Help, please
Please see this link for suggestions on how to resolve this situation:
https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html
Kind regards
Guinot
-
Computer Toshiba laptop does not work after the lid slam... Help please!
This problem with a Toshiba - windows vista laptop began after the cover was closed too hard. When he was conducting swiched, instead of going to the usual blue screen, the screen was grey and a message would come in saying ' it installed program cannot start. " Click ok to stop the computer", as I could not get into windows at all, I took the drastic step to insert the recovery disks that came with the laptop to launch new and see if it worked (a cell phone factory default is is better than nothing).
In any case during the process, which took a very long time, I got messages such as not found HDD1 also say there not enough space to recover. Then I got x:\windows\systems32 and nothing else it got stuck on that for centuries, because he just asked me to check the disk, but I couldn't because I couldn't get a windows session, I looked online and saw something similar to my prob and says type chkdsk c:/f I did after recovering past for much longer afterwards I had to stop at 80% , because there is no room in the end and now I don't even not the blue screen.
As soon as the laptop is turned on, it says, could not start windows. A recent hardware or software change might be the cause to fix the prob insert your windows installation disc. But it won't let me, I get just the same message and also it says File\Windows\system32\drivers\Wdf01000.sys and the State: Oc00000e9 and Info: Windows could not load a critical system driver is missing or damaged.
Please help me if you can, my daughter really needs the laptop works again for homework, thanks a lot
Thank you for taking the time to answer, I think that will be my next move, was hoping I wouldn't have to take to a repair shop, because you never know how it will end up costing, there may be more damage than all formatting, thanks once again :)
-
HP laptop - 15-f233wm: external monitor connected to the HDMI port has video but NO sound
If I connect an external monitor to the HDMI port and check my audio device on the right on the screen cone winder it displays 2 only) 1 HP and Intel) 2 Audio display speakers and No HDMI option selection.
Ernie4576 wrote:
If I connect an external monitor to the HDMI port and check my audio device on the right on the screen cone winder it displays 2 only) 1 HP and Intel) 2 Audio display speakers and No HDMI option selection.
By adopting the option monitor MHDI PC/AV Pc mode will solve the problem, I use a unit screen color Samsung TYPE model / MODEL: C27F591FD (N).
The device playback option on the care of the portable property are all set to default, Intel C27f591 display sound card works fine!
-
I have an old desktop iMac to less than 1 year, I've upgraded to El captain of Yosemite. Just fine, except the quality of the internal speakers. Yesterday, I received speakers brand new engine audio 5 +. Hooked by instructions. Between the speakers volume levels are completely unbalanced. His active in Preferences system - balanced in the Middle, 50-50. Verified in applications/utilities-audio MIDI output, everything is correctly set. I can get pay only by the reduction in volume of the speaker on the right to almost nothing, but then I have no more volume than offer the internal speakers. Any solution would be greatly appreciated.
You use the audio output from your Mac an entry in your speakers or you cross an external DAC first?
I also have the A5 speakers +, and I also use their USB D1 DAC which then audio output runs to the speakers. Yosemite was a constant headache with my setup, but appears to have been eliminated with El Capitan. I installed OSX to El Capitan, as well as later make a clean-install of El Capitan purely for my wanting a clean and in both cases, the sound system was very good. Those who speak of fantastic, better that I have owned yet.
Can you be more specific with how your output of iMac is done? As usually, always check, then check your connections in your speakers and make sure that the audio cables are intact and not frayed. If you use the headset, ensure that the headphone cable is robust and doesn't look like not to is damaged/twisted.
You can consider getting the audio DAC AudioEngine to manage your Mac, as it is much better than one built-in that comes in your iMac. I use it on my new iMac 5K that I received a few weeks ago.
http://audioengineusa.com/store/digital-audio-converters/D1-24-bit-DAC
-
Can be contacted at * address email is removed from the privacy *.
See you soonGeorgeContact Delstra for support with their product.
-
Help, please! Connected to the VPN, but cannot access internal servers.
Hi friends,
I'm a newbie on vpn stuff, I set up a base on a Cisco ASA 5505 vpn by using ASDM, and I was able to connect to it. However, I can't ssh or RDP to one of the servers in the House after that I connected to the vpn. Here is the configuration. Help, please!
ASA Version 8.2 (5)
!
hostname sc - asa
domain abc.com
enable the encrypted password xxxxxxxxx
xxxxxxxxx encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
passive FTP mode
DNS server-group DefaultDNS
domain OpenDNS.com
sc-pool_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
interface ID client DHCP-client to the outside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd dns 208.67.222.222 208.67.220.220 interface inside
rental contract interface 86400 dhcpd inside
dhcpd abc.com domain inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
WebVPN
abc group policy - sc internal
attributes of the strategy of group abc - sc
value of server DNS 208.67.222.222 192.168.1.3
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value abc-sc_splitTunnelAcl
field default value abc.com
a001 xxxxxxxxxxx encrypted password username
a002 xxxxxxxxxxx encrypted password username
username a003 encrypted password privilege 0 xxxxxxxxxxx
a003 username attributes
Strategy Group-VPN-abc-sc
a004 xxxxxxxxxxx encrypted password privilege 0 username
a004 username attributes
Strategy Group-VPN-abc-sc
a005 xxxxxxxxxxx encrypted password username
a006 xxxxxxxxxxx encrypted password username
username privilege 15 encrypted password xxxxxxxxxxx a007
remote access to tunnel-group abc - sc type
attributes global-tunnel-group-abc - sc
address sc-pool pool
Group Policy - by default-abc-sc
tunnel-group abc - sc ipsec-attributes
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:e7df4fa4b60a252d806ca5222d48883b
: end
Hello
I would suggest you start by changing the pool VPN to something else than the current LAN network and see if that helps
These should be the configuration required to achieve this goal
- First remove us pool setup VPN VPN
- Then we delete the VPN Pool and create again with an another address space
- When then attach this new Pool of VPN again to the VPN configuration
- In the last step, we add a NAT0 / exempt for this new pool VPN NAT configuration and remove the old ACL line for the former group of VPN
attributes global-tunnel-group-abc - sc
no address-sc-swimming pool
no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0
IP local pool sc-192.168.100.100 - 192.168.100.110 mask 255.255.255.0
attributes global-tunnel-group-abc - sc
address sc-pool pool
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0
No inside_nat0_outbound access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240
-Jouni
-
No picture on Toshiba Regza TV connection via a desktop pc VGA cable
Hello
I need help to connect my desktop PC Fujitsu Siemens for my Toshiba Regza 37 '' TV via a VGA cable.
I bought a VGA cable, assuming it would be plug-and-play work, far from it.
What happens is that when I connect to PC & TV VGA cable and select mode PC the screen just flickers / flashes a black screen.I read a few articles that you have to press FN + F8 on laptop computers, but I don't have this option on my desktop pc.
Any help would be appreciated. Thanks in advance
Cheerz
Hello
FN + F8 enable and disable the WiFi network!
You must use the FN + F5 key combination to switch to the external monitor.Please also check if the VGA channel is activated on your TV.
Then use the FN + F5 for the external video output switchingBig names
-
Satellite L300-1AQ connection to Toshiba Regza 37 '' LCD AV series 37AV505DB
I think buying the Satellite L300-1AQ, how will I be able to connect to my Toshiba Regza 37 '' LCD?
The LCD has no HDMI VGA port only 2, is a Toshiba laptop equipped with an HDMI port?
What is the most cost-effective way on the connection of all laptops Toshiba to my LCD TV?Thanks for your help...
Hello
AFAIK the L300-1AQ supports only RGB (VGA port) port.
This port provides only the analog signal and I doubt that you will be able to connect to the HDMI port because you cannot convert an analog signal into a digital signal.I put t know the other ports that is supported by the Toshiba Regza LCD 37 ", but I think that in this case, the HDMI port is not useful.
Good bye
-
laptop connected to the tv, good picture but no sound. How to make sound
Hello
I would say go to the control panel in the start menu and clicking noise. You see an option within this selection for audio output? You may need to select HDMI as the main output device.I hope this helps. Just reply to the results.
-
Audio transmission of HDMI to SCART on Toshiba REGZA TV 46SL863
I have a Toshiba REGZA TV 46SL863
I use a home theater 5.1 for audio from the TV via a port SCART (only possible connection)
However, when I receive a signal via HDMI (my ps3) I can't get the sound to play on the home theater. The question is:
* Is it possible to transmit the audio signal from a digital source to the SCART? *
If not, what devices should I buy for those who do? Unfortunately, my 5.1 only accepts entries via a port SCART...
Hmm I never tried this link, but I guess that it is not possible to mix digital and analog signals.
In my case, I connected the PS3 directly to my HiFi receiver.
PS3-> HDMI-> HiFi-> HDMI--> LCDand generally it s common way how such device must be connected.
-
Second laptop connect only with the guest account
I have an E1500 which replaced a broken WRT54GS. I have a desktop office computer using the ethernet cable to the Internet via a DSL Modem and I have two other laptops, one is a Macbook Pro running Lion and the other is a Toshiba running WinXP SP3 using two Wi - Fi connection. Before installing the E1500 all three computers were able to connect to the internet via my secure connection, but now with the E1500, I can get the Mac to connect using my secure WPA2 Personal connection and the Toshiba will connect through the guest account. I lived the configuration wireless for the Toshiba providing several times I put in good properties wireless and network key, but it does not connect. The process of connecting Macbook was a blink of an eye without any problem. I also get Windows XP wireless connection properties back to default (WEP), because it will not hold personal WPA2 settings, but even if it contains personal WPA2 security settings it does not connect. I was also able to connect the Toshiba with the ethernet cable, without going through the wireless network.
Why can I connect via the guest account and not via my connection on the Toshiba? Help someone?
Thanks for the detailed explanation.
I had actually just this solved tonight with about 2 hours of chat with Linksys. It turns out the Windows SP3 XP Toshiba doesn't have a true WPA2 - Personal encryption, only the WPA - PSK (pre-shared Key), while the Macbook Pro has WPA2 Personal. The whole system runs on a hexadecimal code 63. I got the router located on only WPA2 Personal. When I changed (manual) WPA/WPA2/joint, then I had two computers on the network. But then came another problem, when I connected with the Macbook, Toshiba has lost its connection with an error message - "IP address conflict with another system on the network. That proved to be the setting of the channel on the network. The channel was not sync from the old Linksys router configuration. Changed to channel 11 on the router to synchronize with the Macbook Pro and that has been resolved. There is no option for channels on the Toshiba that I can find.
-
Computer laptop Toshiba Satellite A200, Vista, microphone does not work! Any help please!
Hello
Check with Toshiba support, online documentation and drivers (update or reinstall), and
ask in their forums.Toshiba - Forums
http://laptopforums.Toshiba.com/Toshiba - Contacts
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contactToshiba - drivers - access your model
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=downloadToshiba - Support
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp========================================
How to activate Audio devices hidden in Vista and Windows 7
http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.htmlConnect one microphone, music player or other audio device to your computer (you want to be sure
the mic input is enabled)
http://Windows.Microsoft.com/en-us/Windows-Vista/connect-a-microphone-music-player-or-other-audio-device-to-your-computer-----------------------------------------------------------------------------------------------------------------
Pilots may also need to be updated:
Control Panel - device - SOUNDS - look for HD Audio Manager - Mine said RealTek high definition
Audio (this is an example and you can have an other name/maker).Make sure you write down the description and model double click top - tab drivers - write version. Now
Click on update drivers who cannot do anything like MS is far behind the certification of drivers. Then RIGHT
CLICK above and UNINSTALL - REBOOT - this will rebuild the driver stack.If your driver shows 06 you have the default windows and part of the question.
Go to the system manufacturer's website and get the latest Audio/Sound drivers - download - SAVE - go to the place where you
Put them - right click on Reboot - RUN AS ADMIN -.Check the Version tab of the driver in the Device Manager as the restoration of the sound card drivers often
and then install the latest version. Restart and check after each test, not
rare to have to run the pilot of 1 to 4 times or more. Just the version make sure you
installed shows upward on the tab of the driver.
Then navigate to the site of the manufacturer of the device and search for the drivers more recent and repeat the installation procedure.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html---------------------------------------------------------
After the updated driver.
Click with the right button on the speaker near clock - recorders - right click in the box - check see the
Disconnected devices and show disabled devices - check your micro - highlight
then on lower right properties. Make sure that the appropriate injector is selected and check
other parameters - levels tab make sure that MUTE is disabled and APPLY / OK to change.Also in the search for some Audio Manager Panel (perhaps named after the manufacturer of the sound driver). Mine
is the RealTek Audio Manager, yours can be quite different name if you have one.How to activate Audio devices hidden in Vista
http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.htmlConnect one microphone, music player or other audio device to your computer
http://windowshelp.Microsoft.com/Windows/en-us/help/b0e3d7fb-1b4a-4926-8254-65da289209261033.mspxProblems with sound and audio or no sound - a Mr Fixit
http://support.Microsoft.com/GP/NO_SOUNDI hope this helps.
-
Hi, I'm looking to plug:
Toshiba laptop - PSC08E-03M001EN http://www.toshiba.co.uk/discontinued-products/satellite-c650-1ct/
(Windows 7-64 bit)LG HDTV - 42LS3400 link to TV-http://www.ebuyer.com/product/367615
Cable is VGA to red, blue & green cable (don't know name sorry) image of cable here:: http://www.google.co.uk/imgres?um=1&safe=off&client=firefox-a&hs=Y2a&sa=N&rls=org.mozilla:en-GB:official&biw=1366&bih=627&hl=en&tbm=isch&tbnid=urskVAMn94lrQM:&imgrefurl=http://www.alibaba.com/product-gs/631055727/SVGA_VGA_to_Red_Green_Blue.html&docid=2pwndXSQ14pf8M&imgurl=http://i01.i.aliimg.com/img/pb/056/749/507/507749056_659.jpg&w=600&h=453&ei=wvihUbujHvCR0QXx5oH4DA&zoom=1&ved=1t:3588,r:23,s:0,i:162&iact=rc&dur=1185&page=2&tbnh=191&tbnw=253&start=17&ndsp=24&tx=158&ty=123.
Connections are correct & safe, I have:
Display settings - 1 | 2 shows multiple monitors, duplicate.
RES - 1366 x 768, landscape of the screen, displays duplicate. If I'm reading - 'another view undetected. "Graphics settings - Intel Graphics & Media Control Panel-display:
General: Built-in-Display SEC5641, Res: 1366 x 768, color number: 32 bits, refresh rate: 60 Hz, Rotation: turn to normal, scale: scale full screen
Several screens: Mode of operation: Clone screens, the main screen: built in display SEC5641, second screen: monitor
Monitor/TV settings - not supported.Sorry about all this info, just want to provide as much as possible help to identify any problems.
PROBLEM-
My TV displays a picture of sorts however we jumpy/fragile & show three (vertical) versions of the same image on my TV. Black & white, its sometimes a offline.
I have the wires on connected TV where I got my Wired Xbox, the option on my TV to input is the component, when I turn on my laptop & the entry has the value component that I see the image on the screen & clearer, however, after logging in screen disappears & said that there is no signal. The only way I can see anything either again is by ctrl, alt & del.
If I switch to AV2 on the choice of appetizer menu on my TV, it shows the description of the jumpy/fragile image, ctrl alt del - although the picture improves slightly & is not fragile, its still very black & white & duplicated in three patrs.
Any help would be appreciated?
Thanks in advance
Cameron
Hey Cameron,
I suggest you to change the display settings on the computer and check.
Get the best display on your monitor
You can also try to update the latest version of the drivers on the site Web of Toshiba display adapter and check.
Please post back with the State of the question, so that we can help you further.
-
My laptop, connect to the network, but not the internet!
My laptop connects to the network media blank but not internet. My roommates using the network can connect to the internet. I tried various things but not vain. I also tried to get in touch with the Virgin on this subject, but they can help. Is it my laptop and is there something special I need to do with a computer hp laptop. Help, please! Thank you!
Hello
On the Start Menu, click programs principally made, click Accessories, right-click on command prompt and select "Run as Administrator". In the prompt, type the following commands, pressing on enter after each command. Include spaces in the commands, as indicated.
ipconfig/flushdns
nbtstat-r
nbtstat - RR
netsh int ip reset c:\resetlog.txt
netsh winsock reset
Type exit and press ENTER. Restart the PC and see if you can log in now.
Kind regards
DP - K
Maybe you are looking for
-
How can I sign up for Hotmail?
I am come on skype.com and attempted to register. He said that I have a hotmail account, so I should connect with that. So I did. Then he me connected and showed me my new id Skype, which was ' live: MYNAME ' But what is my password? It is not the sa
-
HP elitepad 1000 g2: touchscreen driver missing hp elitepad 1000 g2
Own, I installed windows 10 x 64 on the elitepad g2 1000 HP and after having installed all the drivers, I could not find the drivers for the audio and touch screen. I searched the hp support site, downloaded and installed all the drivers. I started s
-
How to manually remove a virus Alureon Trojan for windows xp
background: 09/04/12. MS security essential and ms security scan unablt to remove this virus. and he tries to clean up and in short time said that I must again and restart once again however, history tells its deletion or quarentined. That's the name
-
Windows Explorer hangs in vista
I use windows vista home edition and using widows Explorer to find files, etc, if there is a problem, that is to say wireless hub or permissions, then explore just hangs. Manager tasks cannot stop the Explorer, the only solution seems to be reset. Wh
-
Wmp54g driver installed, but not seen in the Device Manager
I'm fighting with reinstalling my drivers of network for more than three days already. (For the history, see http://en.community.dell.com/forums/p/19269864/19470244.aspx#19470244) It seems that I finally got the drivers Intel work - however, the WMP5