Laptop HP 14-ac080no: Wireless module not detected after update BIOS

After my 14-ac080no BIOS update F.14 F.19 wireless module is no longer detected. I know not how to go back to F.14, but I would like to know if anyone else has noticed the same phenomenon.

I hope that HP will make new BIOS to fix this one...

Hi @SeppoR,

Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

I stumbled upon your post on the laptop and wanted to help you! I looked in your question about yourHP 14-ac080no laptop and concerns with BIOS and wireless issues. Some say that you could restore the BIOS using factory default values with this. Here is a document that shows you how to restore the default BIOS settings. In this way, it will look at the hardware installed on your laptop.

Please let me know how it goes.

You can say thanks for trying to help by clicking on the Thumbs Up below! .

Thank you.

Tags: Notebooks

Similar Questions

  • Pavilion g6-2215sia: CARD without WIRE NOT DETECTED AFTER UPDATE BIOS

    Recently I have updated my BIOS on my laptop HP Pavilion g6-2215sia think he'll adjust the hardware acceleration feature missing in my system (there is no option in my BIOS to enable virtualization technology). My BIOS version was F.12 and I've updated to F.24, but after update BIOS all my wireless functionality no longer works (including my wifi and bluetooth), and still there is no option to enable virtualization technology in my BIOS settings. On my Windows 8.1 x 64 Pro wifi and bluetooth options are grayed out so I can't turn them on or off. I tried to reinstall my bluetooth driver, but the software says that it doesn't detect any bluetooth hardware. Even when I restart and boot in all my Linux distributions installed on my system (Ubuntu, Quina and Kali Linux) and my x 86 Android, they still do not detect my wireless capability (says Ubuntu, "wifi is disabled by hardware switch").

    To confirm that this was not a software problem, I has conducted an audit of start-up and tested for my wireless module and got this result, "without WIRE MODULE CHECK: NOT INSTALLED". The only way I can get my Windows operating system to recognize my wireless (wifi and bluetooth) is now by doing a hard reset, when I unplug my laptop from the power supply, remove the battery and hold the power button for about 30 seconds. When I turn on my system, then I can turn my wifi/bluetooth on my Windows. But if I restart my system the problem comes back and I can't turn on my wireless. So basically, I have to avoid questioning my system off and only Hibernate, so that whenever I turn on my laptop I can use the wireless. If I restart my system so I have to repeat the hard reset in order to use my wifi/bluetooth, which can be very annoying.

    The problem is that I often use my other Linux disributions and I have to restart before starting in them so that my readers will be mounted read/write, and when I do my Linux can not detect my wireless and it's a serious pain for me because I need to use my wireless often for internet connection.

    Please I really need help on how to fix this and get my wireless working normally without having to do a hard reset every time. I tried to restore my BIOS F.12 unfounded but I don't have the image file (I extensively searched the Internet to find, but does not). I've even updated again to F.26 but I still have the same problem (my current version of BIOS is F.26).

    If you see no updates the BIOS in your list of drivers - where do you have the updates to the BIOS, you used?

    Try here - if you do not see the list of the BIOS, use the "Edit" button to change Windows 8.1 to Windows 8:

    http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-G6-2200-notebook-PC-series/5296082/model/5315061

  • 500-210qe Pavilion: Pavilion 500-210qe: cpu fan not detected after update BIOS

    Pavilion 500-210qe started showing ' 511: cpu fan not detected; F1 = boot' message.  I checked the BIOS rev level and set to upgrade to the latest (80.13 FRIEND) but the problem persists.

    At startup, the cpu fan is not running, but after pressing F1.  Please notify.

    From the least expensive option, replace the cpu fan (which comes with the heat sink) has solved the problem.

  • BT not detected after update BIOS and windows 8.1 & wifi adapter with envy J000 Touch series (J001tx)

    Hi, I have an Envy Touchsmart J001 TX laptop.  I've upgraded to 8.1 Windows a few days back and my pc was working fine. Yesterday, my WIFI and Bluetooth stopped being detected.

    I checked Device Manager and it does not show the adapters. My system has BT Ralink and Realtek wifi b/g/n.

    Restart the system, WiFI present themselves and worked normally, but on next reboot disappeared again.

    The physical plane mode button is orange and pressing or off change in the status of shows like airplane on or off but the notification area icon mode shows no change.

    The network and sharing Center shows not router WIFI in the settings of the card and even the menu of configuration of Windows 8 don't tell no detected wirelessadapter.

    I've updated my drivers and even my BIOS. Earlier I got the version of BIOS INSYDE F.24 and current installed BIOS is INSYDE F.53. Here is the log file in the folder SWsetup containing the unzipped BIOS file. I think that the BIOS is not installed correctly. Please analyze the log file and do not tell if you see something wrong.

    Has anyone else had a similar problem with the update of the BIOS, or with WIFI after Win 8.1 update?

    -Log started: 2014/04/16 19:50:11
    Initializing...
    Log file: c:\SWSetup\SP65654\InsydeFlash.Log
    Settings file: c:\SWSetup\SP65654\platform.ini (found)
    Executable: c:\SWSetup\SP65654\InsydeFlash.exe
    Version: 4.5.6.1 build: InsydeFlash
    Date: Mon 21 Oct 13:11:30 2013

    Resource file: c:\SWSetup\SP65654\iscflash.dll (load)
    Application name: InsydesFlash
    Information of the operating system: Microsoft Windows 8 - supported
    M - FD: 0 0 0 2 does not match FFFFFFFF & 1963103 C! = 1962103 C
    M FD: Match!
    M - FD: FD name 01966.fd
    IHISI Version: 204
    M - FD: 0 0 0 2 does not match FFFFFFFF & 1963103 C! = 1962103 C
    M FD: Match!
    M - FD: FD name 01966.fd
    sH19Infor.dwBootBlockInfo: 10 d
    Check of sign of starting block: 1
    The status of function block start: 4
    Lock status of the EC: 8
    Sign checks number of items: 0
    BBL level: 2
    M - FD has achieved:
    01966.FD
    Offset: 7380688
    Allow Version: 000, Dex: 0
    Current version: F.24, Dex: 3876
    Current BIOS version is greater than the version installed in the Ini.
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    M - FD has achieved:
    01966.FD
    Allow Version: 000, Dex: 0
    Current version: F.24, Dex: 3876
    Current BIOS version is greater than the version installed in the Ini.
    Partition: 1 WMI 0x0D: 1
    Check the package: 1
    Sign of the BIOS: 1
    BIOS size: 0 x 00800000, SHA1 sign size: 0x00000000, SHA256 sign size: 0x00000100
    Sign of the file: 1
    Open file c:\SWSetup\SP65654\01966.fd
    No sign of present
    Reading 8388608 bytes of the file starting with 0...
    The BIOS image size: 8388608 (0 x 00800000)
    sH19Infor.dwBootBlockInfo: 10 d
    Check of sign of starting block: 1
    The status of function block start: 4
    Lock status of the EC: 8
    Sign checks number of items: 0
    BBL level: 2
    Current BID: 0008EFA0, new BID: 0008EFA0 size of BIOS: 00800000
    non_shareEC Ec starting address: 00000000, end of Ec address: 00000000, current size: 00010000, new size: 00010000

    Preparation stage

    Error code: 3010 (0x00000BC2)
    Cleanup phase
    Step completed
    -Newspaper arrested: 2014/04/16 19:50:55

    -Log started: 2014/04/17 22:05:35
    Initializing...
    Log file: C:\SWSetup\SP65654\InsydeFlash.Log
    Settings file: C:\SWSetup\SP65654\platform.ini (found)
    Executable: C:\SWSetup\SP65654\InsydeFlash.exe
    Version: 4.5.6.1 build: InsydeFlash
    Date: Mon 21 Oct 13:11:30 2013

    Resource file: C:\SWSetup\SP65654\iscflash.dll (load)
    Application name: InsydesFlash
    Information of the operating system: Microsoft Windows 8 - supported
    M - FD: 0 0 0 2 does not match FFFFFFFF & 1963103 C! = 1962103 C
    M FD: Match!
    M - FD: FD name 01966.fd
    IHISI Version: 204
    M - FD: 0 0 0 2 does not match FFFFFFFF & 1963103 C! = 1962103 C
    M FD: Match!
    M - FD: FD name 01966.fd
    sH19Infor.dwBootBlockInfo: 10 d
    Check of sign of starting block: 1
    The status of function block start: 4
    Lock status of the EC: 8
    Sign checks number of items: 0
    BBL level: 2
    M - FD has achieved:
    01966.FD
    Offset: 7380688
    Allow Version: 000, Dex: 0
    Current version: F.53, Dex: 3923
    Current BIOS version is greater than the version installed in the Ini.
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    SearchVolumeFileAndCreateDirectory
    M - FD has achieved:
    01966.FD
    Allow Version: 000, Dex: 0
    Current version: F.53, Dex: 3923
    Current BIOS version is greater than the version installed in the Ini.
    Partition: 1 WMI 0x0D: 1
    Check the package: 1
    Sign of the BIOS: 1
    BIOS size: 0 x 00800000, SHA1 sign size: 0x00000000, SHA256 sign size: 0x00000100
    Sign of the file: 1
    Open the file C:\SWSetup\SP65654\01966.fd
    No sign of present
    Reading 8388608 bytes of the file starting with 0...
    The BIOS image size: 8388608 (0 x 00800000)
    sH19Infor.dwBootBlockInfo: 10 d
    Check of sign of starting block: 1
    The status of function block start: 4
    Lock status of the EC: 8
    Sign checks number of items: 0
    BBL level: 2
    Current BID: 0008EFA0, new BID: 0008EFA0 size of BIOS: 00800000
    non_shareEC Ec starting address: 00000000, end of Ec address: 00000000, current size: 00010000, new size: 00010000

    Preparation stage

    Error code: 3010 (0x00000BC2)
    Cleanup phase
    Step completed
    -Newspaper arrested: 2014/04/17 22:06:11

    Problem solved with the permission of edsilha response: http://h30434.www3.hp.com/t5/Wireless-Internet-Home-Networking/Wireless-button-stays-orange-Will-not-turn-on/m-p/914285

    HP technical support comes to walk me through the resolution of this problem.

    1. remove the battery and unplug the power supply

    2. press and hold the power on button for 30 seconds

    3. allow battery but to plug the power unit in

    4. Press power button, then press the f10 key immediately (a number of times)

    5. the bios Setup menu appears

    6. select Reset default values

    7. Select Save and exit

    System boots and the wifi key changes from orange to blue

  • Wireless device not detected after upgrade of windows 8

    I upgraded my HP Pavilion dv6338se notebook PC for windows 7 to windows 8.  Now the wireless device is not detected when I check the settings.  Device Manager showed a coprocessor that didn't have a driver, I downloaded a driver NVIDIA GeForce Go 6150 and the coprocessor error is now gone.  I also updated the BIOS with the latest driver from HP.  Still no joy with the wireless.  Any suggestions/help would be greatly appreciated.

    Hello

    It seems that windows is unable to find the drivers for the Wifi card and the HP pavilion dv6338 model can not have updated drivers for Windows 8 on the HP website.

    I'd still be recommendyou to check with the help of HP if they have updated drivers for the model you mentioned.
     
    HP Pavilion dv6338se PC drivers
    Contact HP consumer support
     
    Hope the helps of information.
  • Drive external DRIVE not detected after update of the Sierra

    I upgraded my Macbook Air Sierra this morning. Since then, whenever I plug in my external Seagate HDD, it is not detected in the Finder, or see a shortcut on the desktop. However, it is visible in disk utility.

    I connected the HARD drive even air to my friend Yosemite running, and it works as usual.

    How the drive is formatted?

    Post a screenshot of what you see in disk utility.

  • XP does not start after update BIOS on Satellite L

    I've just updated my BIOS 2.10 to 2.20 to try to overcome a problem of overheating with Linux.
    The reboot of the XP laptop will not start. I get the XP screen for a few seconds and then the blue screen of death flashes until restarting the laptop before. The blue screen is so fast, that it's not finished writing the text - I can't see all the numbers to check the error.

    If I choose Linux Mint of my GRUB screen, the laptop starts properly. I also see the Windows partitions. I tried to boot from a XP disc to run CHKDSK, but I go to the step where it says it inspects the configuration of my then hangs on a black screen / white and there it is.

    Any ideas? Is it possible to roll back the BIOS?

    Hello

    > Is it possible to roll back the BIOS?

    Yes, you can downgrade (rollback) If you made a backup.

    Can enter you the Bios and check if the compatible mode (after updating the Bios, it might put AHCI default)?

  • Qosmio F50 - bright/Fucntion keys do not work after update BIOS buttons

    OK... I read a similar post and has FACT EXACTLY what IT SAID TO DO... He solved half of the problem or less... after the update to the new bios that I'd like speed or make my Qosmio energy gave me problem from the first day I installed it...

    The reason why I upgraded to was I thought he could solve my problem of flash memory card. They NEVER APPEAR AFTER REBOOTT... I ALWAYS HAVE RESTART THEM IN THE WINDOWS MENU... I thought that if I do a scheduled task. This would solve the problem. Guess what... It SCREWED my windows calendar place... a mistake self-protection
    This brings me to install the new bios... After you install... He has created ONE MORE PROBLEM, INTOTAL - TWO
    (1) KEYS INFORMED DON'T WORK
    (2) FLASH CARDS DO NOT WORK
    After following the instructions of a thread posted here... He told me to remove the VAP and reinstall... Guess what... it solve the key problem... but MY KEYYYYYY FUNCTION... I restored my pc... He said if your function key is disabled... GUESS WHAAT AGAIN... THE FIRST PROBLEM TO... ILLUMINATED KEYS DO NOT WORK... I later discovered that I can't have both things at the same time according to the instructions... Oh Yes... I forgot to mention;... CARD FLASH showing... shut up has never shown... restoration takes me to the original problem...

    I think down my BIOS version that might solve the problem but can't find it... I don t want to restore because I might install additional software like the game... Assassin s creed... BTW... It works AMAAAZZZINNNN... but the multimedia and function keys keep on bugging me
    I have a Qosmio F50-126 with Vista 32 bit...

    Try:

    Reset the BIOS to its default settings.
    VAP to uninstall and install the latest version from the Toshiba site.

    PS I think you can change the lighting in the BIOS, have you checked this setting?

  • Compaq Presario V3118AU Internet does not work after update BIOS and Broadcom Wireless Driver!

    I posted here yesterday on my computer because I have updated the Bios program with the update of the BIOS of 2007 and after that my internet no longer works.   The advice I've gotten is update Broadcom driver wireless as well as I did yesterday but the same result.    I was told also that if all things go wrong can I downgarde my Bios program that imposible because the older version on my computer model page is actually installed now on my computer.  I have run out of idea already of what else could be done please help.    Sometimes wireless connection to connect to the router but often difficult and if I am connected I can't go to the internet and to connect to the Local network I just get limited connectivity.

    Can someone please tell me what to do to solve this problem.

    Thank you very much!

    You are welcome. Let us know how it goes.

  • Audio Jack does not work after update bios

    I'm not able to use my my helmet after I've updated my BIOS and driver audio audio codec IDT high definition.

    I have a probook 4440 with windows 7 (64 bit) OS. Help about my problem?

    Hello:

    The only suggestion I can offer is to perform a hard reset of the laptop.

    http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=110&prodSeriesId=376999&prodTypeId=321957&prodSeriesId=376999&ObjectID=c01684768

    Paul

  • Satellite Z30 - A - 12R BIOS password not recognized after update BIOS

    I updated the bios after that I warned the Bios of Toshiba v3.50. The process was done by the utility software of Toshiba and after restarting it has 'password =' on a blank screen and it does not recognize my BIOS password, write not 'certified '.

    I also tried the HARD drive password, but no luck.

    What can I do now?

    Hello

    Before you try to update the BIOS, all passwords must be removed!
    BIOS password can be removed by the authorized service provider available in your country.

    But the unknown HARD disk password can be removed more.
    In such a case the HDD isn't accessible and cannot be used.

    Mate sorry but in my opinion that you only have one chance to get the BIOS password removed. you need the help of ASP.

  • Right shift key does not work after update BIOS on the Satellite A200 - 28 p

    For some reason, after I updated my Bios, my right shift key doesn't work and no not my FOUR and SIX button, so why I write in words: (,

    I tried to reinstall windows, t hasn't made a difference.
    I tried to roll back the drivers for the keyboard, as well as the move towards the US version of the keyboard, nothing has helped.

    Thank you

    Hello

    What cell phone do you have exactly? And did you use the correct version of the BIOS?
    Have you tried to set the BIOS to default settings?

  • The IdeaCentre 300-01IBY stick is not booting after update Bios

    I just updated to the latest version of the bios update. Immediately after that update the stick does not start. The light flashes for about 15 seconds then turns off - it seems to be in an infinite loop.

    I tried unpluging the USB hub and the memory card - nothing works...

    Any suggestions / workarounds?

    Thanks in advance for your contributions?

    Unfortunately, there is a known issue with the Windows Flash utility that is many devices 'bricks' (broken). You need to update the firmware if or update to the latest version W10 will fail and lock your device. The only approach is to use the flash of UEFI USB stick method (the other firmware download option), but it's too late for you now. You must give your stick for a replacement. Boring, I know. Happened to me too.

  • T410 CTRL key does not work after update BIOS to 1.45 (German keyboard)

    Dear community,

    I updated the BIOS of my TP T410 (2522), German keyboard, to 1.45. After the update, both CTRL keys don't work anymore. Ditto for the AltGr key. When I switch to CTRL FN in the FN key BIOS - as supposed - works like the CTRL key. But when I turn off again the FN returns to his good funtion and CTRL does not work.

    When I connect an external keyboard via USB it works perfectly.

    Any suggestions how get the CTRL key works again?

    Best regards, Simon

    Hello

    turns out be a hardware fault. Swapped keyboard and it works again.

  • ENVY 15 t-ae000: (F2 and F3) brightness control keys do not work after update bios and Windows 10 update

    After that I upgraded to the latest version of the BIOS and upgraded to Windows 10, brightness controls no londer work.

    Would appreciate any help.  Thank you

    Hello

    If your laptop uses Nvidia Optimus (Intel + Nvidia GPU), try to download and reinstall the Intel HD graphics driver on the following link.

    http://ftp.HP.com/pub/SoftPaq/sp74501-75000/sp74569.exe

    When reinstalling, restart the laptop.

    Kind regards

    DP - K

Maybe you are looking for

  • OfficeJet 5740: New genuine cartridge does not work

    I just bought a new ink a few hours there are the target. I played the installation video and proceeded to the installation of the new ink cartridge. Once I had finished the following pop-up came, "remove and install the specified cartridge, ensuring

  • OfficeJet Pro 8600 more printer

    I just bought the printer more Officejet Pro 8600 & installed without any problems, but it doesn't connect to the internet/web services? It is connected to my home network & print etc, but when I try to activate the internet according to the guidelin

  • Grafikcard Vista driver need driver for Satellite P10

    Hello... I installed Windows Vista on my Satellite P10 with only 1 problem.I can't find a working driver FRO my Grafikcard... My P10 is with aNVIDIA Grafikcard... And all the drivers that I found in the Internet areonly at 6100 Grafikcard... My card

  • sp40966 drive firmware update problem

    While they inspected the m9400t support page today, I found the following link: IMPORTANT - prevent any hard drive crash I checked the link and found that I needed this update the hard drive firmware as my main drive is a Seagate 750 GB SATA drive. I

  • SIP: Failure cannot connect to...

    Hello I just got a Quickset SX20 video system for my business. Therefore, I created a SIP account with access to the server of proxy to 'getonsip '. I went into my settings on the SIP configuration, but I got this error: "Failed: unable to connect to