laptop past in an endless loop of starting after the recovery of the PC
I have a laptop of DV2109NR who was riddled with viruses. It was suggested that to make a recovery of the PC hard disk. The first attempt was made without reformatting. After 10 hours, the recovery said that completing. After you click OK, the machine went to the screen of Microsoft XP, then a black screen, then the HP invent screen with options press ESC to change the order of starting, and F10 to access the configuration. This scenario keeps repeating. The computer ran for hours and nothing happened. I then did an other PC Recovery do a reformat of the HARD drive and I am still affected by the same systems. I went in the diagnoses and tested the HARD drive and got an error message 'test status #1-04 Fail', which I understand is a bad drive. The drive was working fine before the recovery of the PC.
I also tried emergency boot CD disk, change the boot order, but nothing happens.
Can someone me in the right direction / I hope I did it correctly guide as this is my first time posting. Thank you
If the HDD was beginning of failure, probably the stress of 'charges from virus' and make the recovery pushed over the limit. A new hard drive should be relatively inexpensive and easy to replace. Hope you had a defined recovery disk.
Welcome to the forum!
Tags: Notebooks
Similar Questions
-
HP mini 110-3500 laptop: computer laptop HP mini 110-3500 fails to start after the SSD upgrade
Hello
I recently bought a ' crucial 250 gb 2.5 "SSD and 2 GB of RAM (also by crucial), to upgrade my laptop HP mini 110-3500, who has been extremely slow. But unfortunately, the laptop refused to start when turned on. What can I do? I am very worried.
Enkay1You answered. That's what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will operate at a higher voltage (1.5 volts), but it is not the ideal memory for older hardware. Need memory DDR3-1333 name specified for the HP laptop. You can confirm or refute my diagnosis by putting in the memory of the old and see if it boots.
It's the part number you need:
621567 001
Is your memory has 8 black on the side blocks or just 4? You want 8. Also if you have Windows 7 Starter, you can not use 2 GB of RAM.
If it's 'the Answer' please click on 'Accept as Solution' to help others find it.
-
Does not start after the upgrade to 1.5.
Does not start after the upgrade to 1.5. "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »
All ideas
No problems in the past with edge since September 2012.
=============
Laptop HP Pavilion dv7-2185dx
Dv7-2185dx product name
#ABA product number NV023UA
Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology
The microprocessor Cache L2 6 MB Cache memory
6144 MB of memory
Memory Max 8192MB
Graphic ATI Mobility Radeon HD 4650 (M96)
Video memory up to 2815 MB (1024 MB dedicated)
500 GB (5400 RPM) hard drive
Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer
17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)
Fax/Modem high speed 56 k modem
Network integrated 10/100/1000 Gigabit Ethernet LAN adapter
Wireless Connectivity Intel WiFi Link 5100AGN
The Altec Lansing SRS Premium Sound technology with subwoofer
101 keyboard compatible with the keyboard keys full size numeric keypad with integrated
Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad
PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)
External ports
5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card
4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA
2 headphone
1 microphone input
HDMI
1 VGA (15-pin)
eSATA + USB 2.0
1 RJ-11 (modem)
1 RJ - 45 (LAN)
expansion port for computer 1 cell 3
1 IEEE 1394
irewire (4 pin)
1 consumer IR (remote receiver)
Other devices HP Webcam with integrated digital microphone
Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)
Weight lbs 7,74
Housing for Kensington MicroSaver Security lock
Turn on the password
Accepts 3rd party locking safety devices
Software
Operating system:
Genuine Windows Vista Home Premium 64-bit with Service Pack 1
Hi, people.
I was able to reproduce the problem here, so the good news is that you're not imagining things. We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top. This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform. We will do the best we can and we will keep you guys, update as to what status is.
Thank you
-Elaine
-
Problem starting after the installation of the NTI Echo Satellite P50-B-11V
Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).
Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).Anyone facing this problem? Please advice if you have the time.
I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.Thanks fo your time.
Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).Anyone facing this problem? Please advice if you have the time.
I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.Thanks fo your time.
Dear marianbur,
New laptop having same problem here, is now stuck... Have you received still no solution?
Greetz
-
Two iMacs does not start after the 10.11.4 update.
Two iMacs does not start after the 10.11.4 update. Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd. He then gets stuck in a loop trying to start. Tried to reset the SMC and LANDAU. Without success. Started in recovery mode and ran disk utility. Discs said OK. Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).) Installation is finished but still once does not start. Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater. Installation seems to work, but once again, the macs will not start. Same 'unexpected launchd sigkill' error. A mac is now back working properly with 10.11.3 the other will be shortly. Is there a problem with the accession? Our COMPUTER support use Munki to get updates from one day to the next. Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.
More information: two bricks iMacs were late 2013 models. A 21 "and a 27. We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.
-
Original title: xp does not start after the installation of avira
I have a HP Slimline s7410
XP Home Edition SP3
I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
I have a cd/dvd drive of work.
I don't have an XP bootable installation CDMy system worked well until: I installed the free version of Avira
Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.Here's what my BSOD looks like:
Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
Technical information:
STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)Any help is greatly appreciated! :)
My first suggestion is to do a system restore at this time point.
second suggestion is to keep your external drive connected to the pc at all times. only detach when necessary. of course, it would be better to install a second hard drive in the computer instead. in any case, keep your personal files out of the system disk is a wise thing to do. You can also download and store files for free on the Microsoft Skydrive site.
third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month. Basically, you can open the Explorer and right-click on the drive letter. then select Properties, and on the Tools tab, you will have the opportunity to run the disk check. then reboot and do a Defrag. where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.
Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.
so my suggestion is to do a series of tests using your cd bootable your computer works. see if you can actually run a chkdsk/r at the moment with them. If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them. in any case, see if your boot at the moment media can run a check disk at all, and let me know.
fifth proposal is to install "microsoft security essentials" like your anti virus program. even if you have run ubantu, it is not likely to have been an infected copy. anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations. the people who make the virus deliberately their engineer for the windows operating system. If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too. Although they no doubt, attacks are more frequent for the windows os.
-
I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.
The primary partition has the following folders (including hidden & system)
The recovery partition has the following (including the language files more)
Someone at - it ideas why my laptop does not work?
Thank you
Greg
Hello
You press F11 on startup with a HP Compaq to start the recovery process.
For problems with the recovery process, you will need to contact HP.
BIOS problems:
There are messages for the HP Forums for posters with similar errors:
All the answers it point to a drive about to fail
See you soon.
-
Cannot start after the blue screen "page in the nonpaged area failure."
My sons laptop has got to me. There the error page blue to come with "failure page in the nonpaged area." There is a chain of technical info of numbers, but this changes a little at each attempt.
I tried all F8 options, without success. I did a restore disk from the laptop of my other son (which is the same) and that has not worked and I also downloaded a file of system restore on the internet who do not. I ran diagnostics memory on the scope option and who found nothing.
No matter what I try, always the fails to start after the first screen with Microsoft Corporation at the bottom and the small lights of scrolling!
I would be grateful for any suggestions that anyone can have. I wondered if I should try to borrow a disc of Windows Vista from someone and try from there?
Read the messages and follow the procedures established by the MVP of the spirit in the following thread on the Blue Screen of Death. They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.
I hope this helps.
Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
bbmChatDB of public database;
public static FileConnection fconnRead = null;
public static String fileReadData = "";
public static InputStream is = null;
data Byte [] = null;
DataInputStream is = null;Here is my code...
I have 3 files in my directory... When I run the code I can open a file and read it... but the while loop get blocked after the first iteration... can someone me help or give some indications
try {}
FileConnection fc = Connector.open("file:///store/home/user/documents/BSM/") (FileConnection); "
If (fc.exists ()) {}
Enumeration e = fc.list ();
While (e.hasMoreElements ()) {}
System.out.println ("files are:" + (String) e.nextElement ());
play this file
StringBuffer stringBuff = new StringBuffer();
try {}
System.out.println ("opening file")-;
System.out.println ("file name is:" + (String) e.nextElement ());
fconnRead = Connector.open("file:///store/home/user/documents/BSM/(String)e.nextElement(),Connector.READ_WRITE) (FileConnection);
System.out.println ("data length")-;
If (fconnRead.exists ()) {}
is = fconnRead.openDataInputStream ();
data = IOUtilities.streamToBytes (is);
Ddd = new String string (data);
fileReadData = ddd.toString ();
System.out.println ("length of data:" + fileReadData.length ());
System.out.println ("read data :" + fileReadData);}
} catch (IOException ee) {}
ee.printStackTrace ();
System.out.println ("Exception in the read data :")
+ ee.getMessage ());
}}
}} catch (IOException e) {}
e.printStackTrace ();
}{Finally
try {}
If (is! = null) {}
is. Close();
}
System.out.println ("is closed...");
} catch (IOException e1) {}E1. PrintStackTrace();
}If (fconnRead! = null) {}
try {}
fconnRead.close ();
} catch (Exception e) {}
System.out.println (try ());
}}
}
You can recode this treatment so that it uses only:
e.nextElement ())
Once a loop iteration.
Directly at the start saying something like:
String fileName = e.nextElement ());
and use fileName everywhere in your loop.
Also be aware that printStackTrace() will do nothing in your situation, it only works if you catch Throwable. So make sure you something output all your catches exception and also have a catch (Throwable t) to catch the things you miss, as follows:
{} catch (Throwable t)
t.printStackTrace ();
System.out.println ("Eception exception:" + t.toString ());
}
I think your code is thrown an exception and you don't see it.
-
BlackBerry Z10 my BB Z10 does not start after the update today at 91 firmware
Hello
IM from the India. I bought a Z10 only today in the evening. When I arrived home and connected to the laptop, it has proposed an update to my version 261 91. But after that, my BB10 is not start. Just the red light keeps blinking on the black screen. When I tried to reload the software link, it says, the software is uptodate and turns again into flashes red. Please suggest me how to solve this problem as its been just 2 hours, I used the phone and he's dead to me.
Remove the battery for 5 minutes and pop again. In this post, there are two links depending on what type of screen appears once it tries to start, after the red light.
http://supportforums.BlackBerry.com/T5/BlackBerry-Z10/security-wipe/TD-p/2201767
-
Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
Tried running firefox.exe Pei but error message:XML parsing error: the undefined entity
Location: chrome://mozapps/content/profile/profileSelection.xul
Line 18, column 1:
"< dialog < =" "^ =" "p =" "> < / dialogue >Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.
Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)
-
ITunes does not start after the installation of Windows 10
ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).
Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support
Solution, according to this link, is:
If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?
For general advice, see troubleshooting problems with iTunes for Windows updates.
The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.
Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.
More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.
Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.
TT2
-
Computer does not start after the screen of the bios, Compaq Presario SR1023WM
Ok. Trying to fix a friend's computer and seem to have met a strange barrier.
Problem: The computer does not start after the bios screen.
Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well. And that's it as far as the computer becomes. After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect. I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point. I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected. Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success. I tried using a different memory stick and different memory as well... Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).
The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.
http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.
I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.
I have a pretty strong understanding of computer repair, so feel free to give me something to try.
If you need more information out of me, let me know as well.
Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.
At the back of the pc is the condition of the PSU led green or flashing?
-
Anyone know when will fixed the problem of material with the "IPAD PRO"? The question that keeps it from starting after the load.
According to Apple, it has been addressed in the latest update of the iOS, iOS 9.2.
-
Satellite M40 - 129 stops starting after the Toshiba screen
Hello
My M40 continues sometimes to start after the Toshiba screen. He stops and all I see is the blinking cursor. No Error Message or something else and normal boot from the HARD drive. Boot from CD (for example. Œuvres of Knoppix). This problem sometimes occurs and traceable for me isn´t.Best regards
SpoonyHey Spoony
Unfortunately on this path, it is not easy to say why this is happening. Each user has a specific configuration OS and we don t know how your operating system is configured.
You can boot OS in safe mode? If Yes check what the problem may be a little. If there is anything you can do I recommend you save all your data and preinstall unit using rescue media. If you do this I recommend also to create two partitions.
Don t compare WXP and Linux startup procedure. As you know that Knoppix using just the RAM and no HARD drive for the race.
Maybe you are looking for
-
Create calendar of events of the email?
I have not tried using the door-match calendar yet. I use Google Calendar and am satisfied. However, it would be very convenient to convert an email (for example with an invitation or announcement of event) in a calendar event in Thunderbird, then ex
-
How can I get American English spellchecker working when my location is Canada?
I have recently come back Canada formula States. After my place in the Canada, I found that I had lost access to US-spellchecker (which I still need). I looked at various system preferences and have not yet seen how to get back the Canadian spelling
-
Qosmio X 300-15 H - canoe the video driver installation
I can't install the video driver modern (for example, 300 + version). My laptop is not see and identify as a standard driver. What should I do? On this Web site, you have only old version.
-
Envy of HP dv7-j020: Fingerprint reader no longer works
Fingerprint reader has stopped working. I checked for new drivers, and he says he is fully updated. Not sure why it just stopped.
-
decoding error 330 in Internet connection
I recently installed the new internet equpment (modem & flat) to go beyond. Since then, I was not able to use browsers to search or even connect on some Web sites. The error message returns: with Internet Explorer, it is: error 330 (net::err_content