LaserJet 1022n Windows 7 64 - bit Installation problem

Similar Questions

• Wireless Laser Mouse 5000 Windows 7 64-bit installation challenge

  Wireless Laser Mouse 5000 Windows 7 64-bit installation challenge continues to get customer assistance contact support when you try to load the software to control the mouse buttons and the speed of response.

  Suggestions?

  Hi OrlandoM,

  Using the latest 64-bit drivers? Visit the Microsoft Hardware site and download the latest 64-bit driver software:

  http://www.Microsoft.com/hardware/download/download.aspx?category=MK

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com

• "Laserjet 1022n Windows Update", causing problems printing: print jobs do not print

  Hello

  A few days ago I installed upgrading Windows Laserjet 1022n on my Windows 7 64 bit and since then I can not print a page normally: the page does not print. I use a TCP/IP network port.

  I made several attempts to resolve this problem:

  -uninstall the printer driver and install it again (I tried the latest version on the HP site and an older one that worked perfectly before)

  -update the firmware of the printer to the latest version on the HP site.

  When I put the printer in pause and start the print job, you can see in the list. Resumption of the printer, printing starts on the printer but you see that the job remains in the list, flashes again and again. The printer keeps printing the same page.

  I don't know what I can do to solve this problem. There is no way to uninstall the update of the HP Laserjet 1022n software because it does not appear in the list of installed programs (course list is also op updates from windows updates).

  I have same problem printing to the same printer from another PC Windows 7 (with the same windows update done)

  But I have no problem printing with my laptop on an other network printers.

  Is there someone who has the same problem and how to solve?

  Thank you for answer

  I found the solution on this site: http://www.tomshardware.co.uk/forum/59912-29-1022n-printer-stop-printing

  Just uncheck the chekbox "enable two-way communication" on the "Ports" tab of the properties of the printer and it works normally again!

• LaserJet 5 M and Windows 7 64 bit - duplex problem

  I have a Laserjet 5 M Postscript with a duplex printing unit in my home network.

  Windows 7 64-bit, the duplex printing option is not displayed.

  1. I reinstalled the driver - cool from MS
  2. I manually changed the ' properties/device settings' to indicate the duplex unit is "installed".   I have administrator privileges.
  3. I rebooted the machine.

  However, under preferences - or for actual printing, under available - possibility of double-sided printing is not displayed.

  Any help will be appreciated.

  My two machines from Vista (32 & 64 bit), with no problems, print double-sided on it.

  Alright George. I have discussed this with my colleuges and we agree that this thread would be better suited in the business forum. Since it is a printer and we focus only on consumption patterns. We would do a disgrace to not send you over there.

  Here is a link to Board commercial laserjet.

  Business - LaserJet HP Support Forum

  Im going to have a moderator hover over this thread to the business section for the best chance to get a solution.

  Take care!
  Sean

• Office Jet Pro L7580, Windows 7 64-bit Installer

  I have a Dell Studio Desktop, which I updated to Windows 7 32-bit to Windows 7 64 bit. Now, I'm trying to reinstall the drivers for my Office Jet Pro L7580. The Office Jet and the Dell Studio are on a cable network.

  I tried to use the HP printer install Windows Wizard, but whenever I use it, I get the message "the wizard has detected a problem with the software driver for the selected printer. If I continue I then I get a message "the system cannot find the file specified" or a message indicating that an error has been detected and the system must be closed. Once, I don't have the progress bar, but it did not move past the first step.

  Before performing the installation, I disabled the TSRs terminate and stay, erased from records and trust temporary and disabled my McaFee firewall. Just as it had all but recommended no advantage.

  I also tried to use the utilities to remove the driver, two of them, but this made no difference either.  The documentation says that the driver removal utilities will run at 4 levels. I do not know how, because it doesn't seem to be an exe file. However, when I run the batch file "Uninstall" Windows, it seems to work at level 2 and ask as I restart the system. Deleting driver utilitiesboth I raced my attached printer and not connected to the network.

  I guess the message "The wizard has detected a problem with the driver software" must disappear before I can get a positive result. I guess also that this message is displayed because there is some residual remaining Windows 7 32-bit software that utilities to uninstall Windows not delete because they are not executed correctly.

  Any suggestion would be appreciated.

  Having investigated a bit more, there are a couple of logs who recommend using Revo and CCleaner to remove songs flying over a previous installation. I've loaded and executed these two and Revo has found a large number of entries that I deleted.

  I then ran the wizard again and after a lapse of acertain time and a recommendation to turn my anti virus software I know succeeded. I will think long and hard before repeating this procedure.

• How to change the default Windows 7 64-bit installation directory?

  Just installed Windows 7 64 bit home edition, can't seem to change the default installation with regedit successfully directory. Is no problem in XP. I have the windows installed on a small SSD with a second hard drive to use for progams for example F:/Program Files.

  Anyone done this successfully?

  Thank you very much

  Steve.

  The 64-bit version has two versions of regedit. Make this change as well:

  1.) go into start > run: %systemroot%\syswow64\regedit
  2.) pass: HKEY_LOCAL_MACHINE-SOFTWARE-Microsoft-Windows-CurrentVersion
  3.) change the path in DWORDs ProgramFilesDir, ProgramFilesDir (x 86) the new path, probably just change the drive letter.

• PowerEdge 2600 and Windows Server 2008 R2 installation problem

  Hello.

  I have a Dell PowerEdge 2600 server. Here is the configuration:

  BIOS version: A14

  2 x Intel Xeon 2800 MHz 533 MHz, 512 k (SL6VN)

  4 x 1 GB of RAM

  2 x 146 GB (IBM-IC35L146UCDY10-0) in RAID1

  6 x 147 Gb (Fujitsu MAP3147NC) in a RAID5 configuration

  Firmware for the PERC 4/Di 2.52D

  It has worked well during the installation of Windows Server 2000. But now I need to install Windows Server 2008 R2.

  Here's the problem: when I boot server to Windows Server 2008 R2 installation DVD, it starts to load the files and after a few minutes shows an error (I copy the exact error number) who said he's trying to run the 64-bit application, but unfortunately, this processor does not support 64-bit applications.

  I was able to find a download for Windows 2008 x 64 on the page Support of Dell PowerEdge 2600. This means that you can install an operating system 64-bit on this PE 2600, is it not?

  I know that Windows Server 2008 x 64 and Windows Server 2008 R2 are different operating systems, but 64-bit is always 64 - bit.

  Also, I know that Intel Xeon 2800 MHz 533 MHz 512 kb (SL6VN) is a 32-bit processor, but if it was delivered with these processors, and there are downloads for 64-bit operating systems exist, it should be able to install these operating systems.

  Please tell us how can I install Windows Server 2008 R2 on the PowerEdge 2600.

  Thanks in advance.

  The list 2008 x 64 in the list of OS for the 2600 is clearly a typographical error / support/web content team:

  • The 2600's chipset does not support ALL 64-bit processors
    http://Ark.Intel.com/products/27741/Intel-E7501-memory-controller
  • No. 6 systems are supported on 64-bit OS - not all listed here, but the 6600 lists NO 64-bit OS (8 G was the first):
    http://advisors.Dell.com/AgileWeb/iDrivematrixView.aspx
  • 2003 x 64 is not no more, which would be if 64 bits have been supported all the

  You pay for 2008 x 86 as the latest OS on 2600... or get a newer server (starting with the 8th generation of servers as the PE 2800) to operate 2008R2.

  "2008R2 is a 64-bit operating system that is not as forgiving as 2008 x 64 on the execution of threads of 16 bits."

  16-bit applications are not supported in 64-bit operating systems:
  http://blogs.technet.com/b/chitpro-en/archive/2009/04/14/Windows-and-16-bit-applications.aspx

• Win 7 64 bit installation problem

  Hi, okay so I have a dell inspiron with windows vista 32 bit and I am trying to install windows 7 64 bit, I followed all the instructions and everything works fine until it gets to finish install, after the first reset itstarts completing installation and then I get a blue screen with the 0x000007e error code. I tried to remove ram and installation with only 2 GB, I downloaded a new startup of windows 7 on a flash drive to see if the drive has been courrpt but I got the same error, I also tried to projecting my drive hard and still no luck. Any ideas?

  Thanks in advance,

  Nathan

  Hello

  Check the BIOS settings and change the SATA AHCI option and check. Consult the computer manual or contact their support site.

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  You can read these articles and check if it helps:

   

  Windows 7 installation problem: hard drive not found

  http://Windows.Microsoft.com/is-is/Windows7/Windows-7-installation-problem-hard-drive-not-found

   

  Windows 7 installation problems: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/Windows-7-installation-problems-frequently-asked-questions

  You can also check this thread that resembles the similar issue that you are facing:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/0x0000007E-during-installation-of-Windows-7-Pro/65d83a65-5173-4b60-97F5-ff3e2e315b90

  I hope this helps. If you need help with Windows, let us know and will be happy to help you.

• What Windows 7 64-bit installation crashes with BSOD when you ask to Raid driver

  Original title: HP dv7 7008 own ssd install question.

  While he was trying to do a clean install of Windows 7 64 bit Ultimate built in 32gig ssd blocks on a 7B BSOD.  Tried to re - install the driver iastor.sys, intel RAID ultilty without success.

  I tried to restore to the factory but can't.  Can boot from image of Windows 7 on USB and try to re - install.  Installation asks for the driver that I provided and about 30 seconds later it BSOD.

  HP uses a 32gig like Accelerator HD SSD where the problem with the iastor.sys.  There is no option in the BIOS to what whatever relevant and I am at a loss.

  Don't want to send it back under warranty.

  Turned out to be a bad SSD returned and replaced with new ones.  Just glad to know I wasn't losing my mind.

• BSOD - Windows 7 64-bit VM problems

  People of greetings,

  My apologies if this is a basic question / repeated. Am a newbie and trying to work my way through the implementation of a virtual machine for my new PC at home. Looked through a number of other threads (in addition to searches on Google) and decided to publish it after I couldn't know the answer.

  What I did:

  1. download the latest version of vCenter Converter Standalone Client (v4.3) and installed on my desktop computer HP with 8 GB of RAM and 1.5 to SATA HDD with Windows 7 64 - bit OS. The detailed specifications for desktop can be found at http://www.shopping.hp.com/webapp/series/category/desktops/HPE450t_series/3/computer_store

  2. created a P2V image with default options with the tracking changes by the limitations of the converter physical version - CPU reduced to 2 of 8 logic/4 physical - and 1 GB of RAM. A took about five hours to create the virtual machine on a joint Seagate FreeAgent external hard drive connected via USB

  3 downloaded the latest version of VMware Player (v3.1.3) and installed on HP desktop computer. Copy the virtual image of the external Hardrive to Seagate FreeAGent to a folder on the HP desktop computer. Pulled up the player and changed to 4 processors and RAM 3 GB since the player provides for this.

  The problem:

  The VM loads and gets to the point where the spheres of four color converge during the boot sequence. And then a BSOD that flashes by quickly and goes to a BACK screen with two options - Windows repair and start Windows normally

  Selection of the "start Windows normally ' returns you to the same place, that is to say." a closed loop

  Selection of "Repair Windows" does not help because I do not have the Windows 7 installation disc (HP does not ship disks to the Windows operating system and recovery disks don't seem to help with this) as the virtual machine does not seem to access

  The Ask:

  How can I capture the BSOD details to validate the error code - turned quick snap capture my eyes indicate that it is the error 7 b

  Recommendations to address this issue seem to suggest a change to the entries in the SCSI VMX file but my VMX has none of these entries. My VMX file is attached for review.

  Would appreciate suggestions/tips/links that will help me to solve the problem

  PS: I tried initially to go down the road of Windows Virtual PC where I learned that Windows 7 64-bit is not a guest operating system, but I still have the virtual hard drive during this activity. The virtual hard disk was created using the utility DISK2VHD. Thought I would mention where it is customary.

  ide0:0. Present = 'TRUE '.
  ide0:0. FileName = "HP450t.vmdk".
  ide0:1.present = 'TRUE '.
  ide0:1.AutoDetect = "FALSE".
  ide0:1.filename = "E:".
  ide0:1.DeviceType = "cdrom-raw"

  That's what you have now.

  We change that to

  bios.bootDelay = "5000".
  scsi0. Present = 'true '.
  scsi0.virtualDev = "lsisas1068".
  scsi0:0. Present = 'true '.
  scsi0:0. FileName = "HP450t.vmdk".

  IDE1:0. Present = 'true '.
  IDE1:0. DeviceType = "cdrom-image".
  IDE1:0. FileName = "windows7-64 - recovery.iso.
  IDE1:0.startConnected = 'TRUE '.

  the next time you start, you need to hit ESC - and then select CD as the boot device.

  Leave the boot CD and escape any questions

  After the initialization is complete, click CMD and run regedit.
  Select HKLM, then Menu > file > load hive.
  Navigate to the Windows directory on the virtualdisk > system32\config and select the file SYSTEM.
  When asked for a name enter p2v.
  Then find the key

  HKLM\p2v\ControlSet001\services\LSI_SAS

  go to the 'start' subkey and the departure of type REG_DWORD 0
  Select HKLM\p2v, and then click Menu > file > unload hive.
  You can now close regedit and restart.

  After that CD-boot the next time should go to hard drive - use safe-boot on the first boot.
  most likely, it works now.

  Use the attached vmx

• print LaserJet 1000 windows 7 32 bit driver

  Looking for a laserjet print driver 1000 windows 7 32 bit.

  There are no Windows 7 drivers for this printer.

  You can download an alternative driver for the printer to print. (Shane_R) has a great post on how to download.

  http://h30434.www3.HP.com/T5/printer-all-in-one-software-drivers-e-g-Windows-8/How-to-assign-alternate-print-drivers-in-different-versions/TD-p/1957011

• LaserJet m1319f windows 7 32 bit

  OptiPlex 755 (Dell) running Windows 7 32 bit with 2 GB of memory. Printer is a m1319f laserjet with a new download of the complete solution from hp.com software

  Printer factory dialog box keeps disappearing in favor of the Windows dialog box and the printer disappears randomly and stops working.

  Hi wunderkin

  When the computer is then it will do a check for all the hardware devices including printers. It could very well have something to do with it. It would be a good idea to leave the printer on except if course be away for a long period of time.

  This printer has Energy Star, whose energy consumption is significantly reduced in ready/standby mode, which saves natural resources, and saves money without affecting the high performance of this product.

  Have a great weekend!

• HP laserjet 1022 windows 7 (64-bit) will not install printer what can I do?

  1 HP LaserJet 1022 printer

  2. Windows 7 64 bit

  3. No Error Message

  4. the only changes to the system are updated security Windows Updater. This is a new computer and old was under XP.

  I tried to delete the printer, newer software (lj1020-HB-pnp-WIN64-en) download and try to install it, add the printer through windows and even the printer will not work. The cd version will work until you are asked to connect the printer and then nothing happens. I even tried to run overnight to see if it find and install, but nothing happened. This printer is a workhorse for me and I want to keep running, any suggestions on getting this printer is recognized and run again?

  See if the 1022 is listed under other devices in Device Manager.
  Under 'Other devices' right-click on HP 1022
  Select "update driver software... »
  Choose "Browse my computer for driver software".
  Choose "Let Me pick from a list of drivers for devices on my computer.
  Select 'Printers' > next
  Under the "factory" > HP
  Under "Printers" > HP Laserjet 1020
  Select "Yes" to the warning popup

• HP 3015 Laserjer: Laserjet 3015 Windows 10 (64-bit)

  I just bought a computer with Windows 10 (64-bit).  I have a HP Laserjet 3015 printer that works fine on my old computer XP OS.  I downloaded the HP Universal driver but the computer still will not 'talk' to the printer.  Any ideas on how I can make the printer work with this windows OS 10?

  Thank you

  RodS12

  Let's try to present once more.  Do not download anything.  Remove only the prnter and you have downloaded all the drivers.  Now turn off the computer and turn the printer off.  Start the computer again and when the computer has finished booting, the printer and when you're ready, plug the usb cable from the printer into the original port.  We should have found new hardware and it should load it all for you. Let the computer search for the drivers and see what happens.

• HP Laserjet 1000 Windows 7 64-bit?

  I tried everything I could locate using the internet, search engines to try to Windows 7 64 - bit print on a HP Laserjet 1000, which is connected to an XP machine in my work group home. Of course, I can print fine to an XP machine in the same workgroup. But not from Windows 7 64 bit.

  I was able to install drivers XP Laserjet 1000 and print from virtual XP Mode. Works very well.

  But I'm unable to see or to print to the printer shared outside the virtual XP Mode in Windows 7.

  What missing am me?

  ZZ.

  See http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=120&prodSeriesId=3463669&prodTypeId=18972&objectID=c01856597

  The Laserjet 1000 is category 6 - not supported under Windows 7.