LaserJet 4: laserjet 4 - toner smears on the edge of the paper 3/8 "wide

Similar Questions

• LaserJet M451dn: Laserjet 451dn toner yellow bleeding at the edges

  My Laserjet M451dn started bleeding yellow toner on the edges of the paper.  I ran a cleaning page and that it stopped for a short time and as but now he's back, it looked like already.  If I print the document in black and white it is not.  I have attached a picture of a scanned page.  It's worse that what looks like the picture as yellow does scan well.  Also, we used only the new HP cartridges in the printer.

  It's a defective toner cartridge.

• LaserJet 600: toner, laserjet 600 on the page

  I have a question where there is some toner transferred to some parts of the page, it should not.

  On the right side of the page, there will be 4-5 "burrs" toner that go from the top down. It seems it's the toner of something that has been previously printed. For example sometimes the task is sufficiently readable to see what the letter a or the number 2 and so on.

  I can print through about 10 pages of blank paper after the 3rd or 4th book that the task will disappear. As soon as I print something with the text on the entire page appears again.

  I exchanged the toner of other laserjet600 which did not work properly and that did not fix the problem. I did a little cleaning on the rollers where the toner fits into the printer. I ran a cleaning page of in the software of the printer.

  So far, nothing has worked. If anyone has information, it would be wonderful.

  Looks like you have a bad fuser unit

  You have a number of more accurate model for the printer? Is - it can be a M601?

  M600 printers that I am familiar with the fuser unit is very easy to remove, so you can swap between the two printers and make sure it is the problem.

  You will probably find even with the exact model number a YouTube video showing you how do to remove and reinstall the fuser unit.

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• Problems with the LaserJet M1217nfw MFP - resolution of the Scanner and ADF feeding issues

  Feature: LaserJet M1217nfw MFP

  Connection: Ethernet

  OS: Windows 7 Pro 64-bit

  1st problem: using the TWAIN software, I am unable to change the resolution of the documents I'm scanning. It displays only the 300 and the menu drop-down does not offer any other parameters. It is having to make each document that I scan a lot more big that it must be, and the company I'm downloading of complained them of the overused storage space.  Device MUST be based on the network for the office.

  2nd problem: the ADF is VERY picky. If the paper is inserted at the stop, it will not pick up and will keep scanning out of the original glass. I usually have 2 or 3 times to find the "sweet spot" where it will actually be a new Pick-up analysis.

  I must say, I was very happy with this product when we got it first, the web interface with the drivers loaded on the printer was a great feature and the installation for each machine went very smooth. However, lately this device became more complicated than a time saver.

  Hi SilentbobSC,

  Follow the steps below.

  1. click on settings

  2. remove the checkmark of "Display the dialogue from TWAIN to allow cropping and low sweep"

  3. click on the drop down arrow to adjust your ppp settings

  

• LaserJet pro 200: location of the country of my printer was incorrect

  Just installed this printer.  When he asked the countries that I said OK to the New Zealand instead of the Canada.  Now, she wants to do it all in A4.  How can I fix it?

  Hi Michael,

  I admit it - I had to laugh, but I certainly don't think you are a fool.  I know that some products are not perhaps too clearly labelled.

  For the LaserJet Pro 200 Color MFP M276nw, to solve the problem of the country, you can do a cold reboot.  Please note that when you do so, the information and parameters are reset:

  ●Tous menu settings are reset to the factory default values.

  All location settings, such as language and national and regional, are reset.

  ATTENTION: All integrated network settings are also reset. Don't forget to print a Setup page before you run the rest. Make a note of the IP address that is listed on the Jetdirect configuration page. You may need to restore the IP address after an initialization/reset NVRAM. After performing a reset/initialize NVRAM, reconfigure all computers that print to this product.

  Here are the steps:

  1. turn off the product.

  2 press and hold the lower left corner of the screen when you start the printer. There is a secret place on the screen which will trigger the cold reset process.  The spot is where the progress bar starts when the machine starts.

  When the product has completed the NVRAM initialization, it returns to the ready state.

  With regard to double-sided printing, here are the instructions for the M276nw.  The instructions are similar to another product - it must still move the paper.

• Lost HP LaserJet 1100 disc lost for the printer and the need to re - install urgent! the printer

  I have a HP LaserJet printer and have lost the disc. I need to reinstall the printer so I can print the document again and I also tried the installation procedure. Help

  Hello

  You can download the software here...

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=UK&prodNameId=14925&prodTypeId=18972&prodSeriesId=25470&swLang=8&TaskID=135&swEnvOID=228

  Tricky

• MFP HP LaserJet Pro M126nw: Clarification of the use of HP Laser Jet MFP M126 nw Pro Page

  Hi support them.

  Recently, we bought a new HP Laserhet MFO M126nw Pro. The cartridge came with the new printer. I need a clarification of the HP Laserjet Pro MFP M126nw on the usage Page.

  We want to know how many pages that the printer has taken so far, printing and also how many pages is analysed and the copier took how many pages.

  I have attached the report using page for your reference.

  Please specify the things below.

  Pages for the scanned copy = 65

  I think he has counted only scanned copies 65.le is okay?

  2. What is Monochrome pages printed from copy = 66

  3. What is pages scanned host = 86

  4. print engine:

  1. total Impressions showing 829.

  Overall, I think it's showing printing, copier, 580 the scanned pages. Is this OK.

  2. What is jam events?

  It's showing 1.

  3. What is EconoMode Impressions?

  showing 0.

  4. What is monochrome prints?

  showing that 829

  Need to clarify the details above for my knowledge.

  Your support is much appreciated.

  Thanks in advance

  Concerning

  R.Pradeep

  the digital and print values are different.

  pages scanned copy 65 - this means that 65 pages have been executed by the scanner with someone using the copy function. the report shows 66 printed pages 'copy' which means 64 of these copies were only a single copy and 1 scan someone made 2 copies - which gives you a total of 66 pages printed from the copy function.

  pages scanned to accommodate 86 = that means 86 pages were executed by the scanner with a person who uses the "scan to network folder" or "scan to computer" function

  That's a total of total of 151 pages run through your scanner. only 2 values that you add to the scanner are the "copy" and «scan to host» numbers copy of 65 + 86 scan-to-host ='s 151 total scans

  total impressions are 829. pages printed from copy fuction are 66 - if you subtract 66 829 that gives you the number of pages that have been printed from a computer = 763

  763 pages printed computer + 66 pages printed using the copy function = 829 total number of pages printed

• HP LaserJet MP604: HP LaserJet MP604 do not print the PCL NET files

  Hello.

  New HP LaserJet MP604 printer does not display files PCL through a network, sent directly from PC.

  It print file correctly to the Web Interface (upoload PCL file https://10.17.200.112/hp/device/Print/Index), , but not network.

  I don't have these problems with the previous model HP LaserJet M602, it print properly the network file.

  Also when I print from MS Word, I see, what format of file (from to C:\Windows\System32\spool\PRINTERS printer spool) changes SPL, before (for printer M602 files are plain text with PJL and PCL commands), but for printer files as zip/xml MP604.

  What can I do to change the settings for HP LaserJet MP604 so that he began to support PCL printing directly from the net?

  And what I have to change to see PCL/PJL commands coil?

  >>... If the file contains only plain ASCII text nothing prints and no error message...

  So maybe the definition of the '\\msk-ent01.ru.ori.local\intop1lj' target is incorrect?

  I remember vaguely when using "copy" at a command prompt session Windows, the target must be a Windows share name, preferably the one corresponding to the final part of the name of 8 characters or less.

• Cannot get 100 colorMFP LaserJet M175nw printer mode 'sleep'. the LCD stays on?

  　

  I have a printer HP LaserJet M175nw colorMFP 100.  the printer is hard plugged into a local home network and is accessible through a static ip address, the family is using windows xp. I tried to get the printer mode 'sleep'. I went into the setup of the printer lcd menu and set the printer mode standby after 15 minutes. However, I don't think it's ever enter mode 'sleep'. a green light stays on and the lcd screen stays on also. is this a normal behavior?

  　

  Thank you

  w

  webster22, is this printer connected on a wall or on a surge protector?

  If you have gone through the Setup Menu the Setup Menu under 'Energy settings' and the system chosen for the Sleep Delay option, then you have successfully configured the printer for its energy conservation mode.

  I find not specific, it is possible that the screen can stay in this mode, however most of the time the power off screen is a feature of mode 'sleep'. With the screen being on this subject is still possible it's save energy by stopping all other drains power.

  You can also check the firmware of the printer via the link below to make sure it is up-to-date.

  http://goo.GL/2v9ip

  I hope this helps!

• HP Laserjet 500 colorMFP M570d: printer HP Laserjet 500 colorMFP M570dn reflecting the situation of "on paper", but the paper is present.

  HP Laserjet 500 colorMFP M570dn reflecting the situation of "on paper", but the paper is present. Effects of several operating system platforms; 10, 7, 8.1, 2012 R2 server.

  We have this printer is installed on a server for printing on 2012 R2 server configuration. Everything works fine until today. The status on the side of things, regardless of the OS, OS shows the printer status is "on paper". Paper has been confirmed in the printer, cleaned rollers, test pages, copy made, etc. When you submit a print job, the State remains the same, just, the job is in the queue and does nothing.

  Any help would be appreciated.

  CRI_IT_guy

  When the software indicates out of paper, it's really tell you he lost communication with the printer. It could be a server problem.  To test since you already know that the printer works would print a printer configuration page and using the printer ip address set up on top of one of the computers as a local tcp/ip printer without going through the server, so the computer prints directly to the printer.  If it works, then your issue is network or linked servers.  Make sure that the address of the printer has not changed and also make sure that the spooler is running on the server.

• Helps with the size of the paper M1176n MFP HP laserjet printer/scanner color

  I've just set up my new printer - HP MFP M1176n color laserjet printer/scanner.  I am based in the European Union and we use paper A4 - but for some reason, it seems to be the impression in a format suitable for American paper size.  Can anyone suggest how to change that?  It's almost as if she makes the smaller document to fit on what would be the American paper size.  But I use A4, and so there is a gap at the bottom of the page?  Thank you, S

  @Simon2014

  Did you enter M176n instead of M1176n?

  Click on the HP Printer Wizard and select game Preferences. The HP Print Wizard should be present if you have installed the full features of printer software and driver.

  You can change the printing options in Windows to change the paper size by default for the metric equivalent.

  

  

  be sure that you save the changes to the default paper size to A4.

  I have a HP HP Envy 120 loan which is an American model. It was provided to me for free by HP to allow me to help answer questions printer.

  I live in the European Union and use A4 paper.

• LaserJet P1102: printer connected to the macbook pro does not let me print double-sided

  I have a macbook pro and an hp laser jet p1102 printer. I checked the duplex printing option, and then the printer printed the first parts of the document, I wanted to print. Then a message appears - "manual Duplex: without changing the orientation, remove the paper from the output of the battery tray and insert into Tray 1 print side down. Do not discard the blank sheets. Then, press the button to go. " I re-inserted paper, but then what I do next as I don't know where this button is Go! Help, please

  Hi @insy,

  I have read your message and see that you are trying to print manual duplex and you get the message to press the Go button. I will definitely do my best to help you. If this helps you to find a solution, please click on the button "" accept as Solution"" down below this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Please, try the following steps to see if it will help solve the problem. Do not take into account the operating system in the title. A solution for this problem is developing. Check the HP website for updates of software and firmware.

  HP LaserJet Pro P1102w printer - Macintosh: only manual duplex printing prints on one side in OS X Version 10.6 when it is connected to a wireless network.

  Good day! Thank you.

• I have two printers. One of them: hp Laserjet P1505n just stop printing. the other is fine. Windows 7. Please notify

  I have two printers. One of them: hp Laserjet P1505n just stop printing. the other is fine. Windows 7. Please notify. Thank you.

  I suggest you to uninstall and reinstall the latest compatible drivers for Windows 7.

  You can also run the troubleshooting of the printer.

  Open the printer Troubleshooter

  Open the printer Troubleshooter by clicking the Start button, then Control Panel. In the search box, type troubleshooting, and then click Troubleshooting. Under hardware and sound, click on use printer.

  For more information, visit the below mentioned link:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Printer problems: http://blogs.technet.com/b/markrussinovich/archive/2010/04/12/3324570.aspx

  Run the printer problems to: http://support.microsoft.com/gp/printing_problems?entrypoint=WHHT

  You can see the below mentioned links.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  http://Windows.Microsoft.com/en-us/Windows7/change-your-default-printer

  http://Windows.Microsoft.com/en-us/Windows7/printing-to-the-correct-printer

• HP LaserJet P1102 cannot print both sides of the paper

  I updated my Windows 8 Windows 8.1 and now I can't print both sides of the paper.

  In my old Windows 8 my printer HP LaserJet P1102 printed the odd sides of the document, then a pop-up window appears and when I click on the 'next' botton and submit the documents to the printer printed the sides of the document. After that the Windows update in the context menu does not appear, so the printer simply prints the odd sides and then nothing happens (just the red flashing on the printer).

  I tried to update the driver (downloaded from your site), but nothing has changed.

  I hope that you can add some useful tips and I can solve this huge problem.

  Thank you!

  Hello

  I understand that you can print is more on both sides.

  When the light flashes try and open and close the lid to see if continues to print.

  (there is no button for the printer but which will resume print jobs)

  I would do a complete uninstall and reinstall the printer software to see if that makes a difference.
  You can download the drivers from this url.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&lang=en&LC=en&product=4110396&

  Win8 and Win8.1 drivers are the same Version9.0.

  If you need more simply make assistance let me know.

  Please let me know if the printer is connected by usb or the installer on a wireless network.

• LaserJet 3020 (also known as the Prod. N ° Q2665A) - where is the scanning software?

  Hello

  I have a LaserJet 3020 (also known as the Prod. N ° Q2665A), with which I would like to scan, when you use a machine Windows 8.1 (64-bit).

  When I go to the HP support page, any downloadable software seems to be on the digitization, it is all about hologram.

  Am I missing something?  Can scan you with the software available on this HP support page?

  Here is a link to the support page to which I refer:

  http://h20566.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome/?sp4ts.Oid=378054&spf_p...

  Thank you!

  Hi JTK,.

  The LaserJet 3020 uses scanning software is integrated in Windows 8. I guess the same is true for win 8.1. This page describes how to analyze with the scanning of Windows software:

  Use the software in Windows 8 to analyze

  I hope this helps.