Latitude E6400, dark on only the lower part of the screen

Similar Questions

• My speakers on my Dell Latitude D820 suddenly emit only a low sound. I adjusted all the volume controls in the menu sounds from the Control Panel, and there is no change in volume.

  Low sound volume

  My speakers on my Dell Latitude D820 suddenly emit only a low sound. I adjusted all the volume controls in the menu sounds from the Control Panel, and there is no change in volume. It's real power radio on the internet and play music from a CD inserted into my machine. The sound icon does not appear in the toolbar.  I tried the fixit of automatic Wndows and it ran and said low volume has been set. Not the case.

  Hello

  1. what operating system do you use?

  2 did you change on your computer?

  Method 1:

  I suggest you follow the link and check.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows?T1=tab02

  Method 2:

  I suggest to follow the link and search for the volume in the taskbar.

  (a) right click on an empty area of the taskbar and then click Properties.

  (b) in the Notification area, click Customize.

  (c) select the volume see the icons and taskbar notifications check box, and then click OK.

  I also suggest you to follow the link and check.

  Change icons appear in the notification area

  http://Windows.Microsoft.com/en-us/Windows7/change-how-icons-appear-in-the-notification-area

• GMA x4500HD on a latitude E6400: how to change the amount of memory assigned to the graphic card

  Hello

  I have a latitude E6400 with the A03 BIOS and lastest drivers memory on Vista x 64.

  I don't see how to change the amount of RAM assigned to the integrated graphics cards.

  How can I change this setting?

  Concerning

  
  

• Satellite P105-S9722 - small dark spot on the screen

  Hello

  A few days there is a 1 cm x 2 cm and a few small black/transparent stained areas appeared on my screen (17 inch WXGA TrueBrite). It's the visibility varies depending on the angle of the lid and disappears almost when it's 90 degrees or if I look at the top (it turns slightly whitish).

  I wonder if anyone had the same problem or knows what it is caused by. My laptop is still under warranty (6 months). I don't remember that the screen has been pressed or anything.

  Thanks for any advice.

  Hello

  If you encounter these problems/errors and you still have warranty then the only choice would be (in my humble OPINION for me :)) for sending the machine to the ASP for a hardwarecheckup.
  Use your warranty rather than wait until your machine drops the line ;)

  Here´s a link to an index of ASP to find the next (and closest) authorized service partner.

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Welcome them

• Flash cs6, each time that launched, never opens. Only the screen saying "" 7 days left to open '. " I tried restoring the system (Win 7)

  Anyone who is familiar with this problem? Help, please

  Hi Aditya,

  Just in case if you have installed creative cloud on the same machine where you had your installed CS 6, then please follow the work around described in the following link: How to convert a trial of Lightroom Lightroom 6 CC

  If this isn't the case, then check out the following links:

  The activation and deactivation of Adobe problems

  Learn how to enable or disable Adobe applications

  Solutions to connection errors, activation and connection with creative Cloud applications and Creative Suite

  If it does not always help you please uninstall Flash CS 6 and reinstall it from the following link: download Creative Suite 6 applications

  Make sure that you select the appropriate language (with which the license has been purchased) during installation.

  Let us know if that helps.

  Kind regards

  Sandrine Bani

• (Redirected) New keyboard for Dell Latitude e6400 does not

  I recently purchased 2 computers laptops dell latitude e6400, but both have the same problem, the keyboard does not. I'm even not go into the BIOS (F2) settings using the keyboard of the laptop. using a wired USB keyboard works very well. any suggestions?

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Bev.

• Latitude E6400 Inverter card

  I recently ordered a replacement screen for a Latitude E6400, when I disassembled the laptop to swap the new screen, the connector that goes to the display inverter plug is different.

  I have to tell the seller what card inverter specification I need, but I have problems finding the specs.

  Any help would be greatly appreciated.

  Your best bet is to ask the supplier of the screen - inverters are specific to the screen.

• How to disable the screen only without pill to sleep?

  Is it possible to disable only the screen, PC not everything? When I put to sleep - it loses connections, turn off 3 G (and he wakes up on the clock), turn off the music. It's terrible. Battery is good enough to work with her.

  Are there ways to tell tablet "turn off screen"?

  Can occur in your control panel. Windows Mobility Center.

  My Lenovo before upgrading to win8 had a turn off display it and also has a separate keyboard shortcut keyboard Fn + F2 to toggle the display.    Looks like a Tablet unless there is a specific or programmable buttons... How do you turn on the screen.

• How to know if Max Rez the screen is Active in R31?

  Greetings!

  I have a Thinkpad R31 with a HD 20gig once containing a corrupted version of XP and now running with XFCE of Maya 13 Mint and Linux Porteus 3.1 versions on it. In Linux, a few background images and compared to the viewers the image show this Rainbow halo effect sometimes found when high resolution images are projected in low resolution on other machines. I have no way of knowing if the original XP rendered better images because he was a native of the machine and therefore typed all the powers of his graphics card. Screen resolution indicators or controls in the two John. Is it possible for me to know if my screen R31 is fully returned to the graphics card Linux max capacity? At the very least, is there a command line to query the computer which resolution mode, it's in?

  Plug display FYI via Porteus:

  NEWS OF THE SCREEN:

  Screen 0: minimum 320 x 200, current 1024 x 768, maximum of 32767 x 32767

  LVDS1 connected 1024 x 768 + 0 + 0 (normal left inverted right x axis y axis) 0 x 0 mm

  1024 x 768 60.0* + 60.0

  800 x 600 60.3 56.2

  640 x 480 59.9

  VGA1 unknown connection (normal left inverted right x axis y)

  60.0-1024 x 768

  60.3. 800 x 600

  640 x 480 59.9

  Use: System memory

  Type of Error Correction: no

  Maximum capacity: 1 GB

  Number of aircraft: 2

  MemTotal: 764428 kB

  MemFree: 102612 kB

  MemAvailable: 484328 kB

  Stamps: 108616 kB

  Cache: 407484 kB

  SwapCached: 0 kB

  Active principles: 380844 kB

  Inactive: 231840 kB

  Active (Anon): 78208 kB

  Inactive (Anon): 68816 kB

  Active (leader): 302636 kB

  Inactive (queue): 163024 kB

  Unevictable: 0 kB

  Mlocked: 0 kB

  HighTotal: 0 kB

  HighFree: 0 kB

  LowTotal: 764428 kB

  LowFree: 102612 kB

  SwapTotal: 8188 kB

  SwapFree: 8188 kB

  Sale: 32 KB

  Writeback: 0 kB

  AnonPages: 96544 kB

  Mapped: 83616 kB

  Shmem: 50492 kB

  Slab: 39084 kB

  SReclaimable: 22316 kB

  SUnreclaim: 16768 kB

  KernelStack: 1848 KB

  PageTables: 2016 KB

  NFS_Unstable: 0 kB

  Bounce: 0 kB

  WritebackTmp: 0 kB

  CommitLimit: 390400 kB

  Committed_AS: 652164 kB

  VmallocTotal: 250040 kB

  VmallocUsed: 7232 kB

  VmallocChunk: 238580 kB

  AnonHugePages: 20480 KB

  DirectMap4k: 16192 kB

  DirectMap4M: 761856 kB

  Thanks for any help!

  Jim in New York

  According to this:
  http://www.ThinkWiki.org/wiki/category:R31

  The A31 has only the screens of resolution 1024 x 768.

  According to your output xrandr, you run to the native resolution of 1024 x 768.

  It is possible that your image viewer (and all that is manipulation of screen) are downsampling bad image.

• How can I change the brightness of the screen?

  Ok. Here's my question. I have a Windows Vista Home Premium laptop. Whenever the charger cable is in it, it becomes more clear. And when I take the screen gets darker. I went to the windows Help Center and they don't tell me nothing. Please please, please answer this question because of this problem, it is more difficult to read on the screen and much more.

  Sincerely,.

  frustrated dark sreen

  The screen options brightening when on battery (when it is normally darker in order to preserve the battery life) are in your power management control panel applet. MS - MVP - Elephant Boy computers - don't panic!

• Computer does not turn on the screens during startup, they remain turned off

  When my computer starts windows 7, my 2 attached screens, which work perfectly well, not to get turned on.

  Thecomputer starts normally, only the screens remain unused.

  I can connect to my account and [alt] + [F4] to turn it off again.

  The only thing I could imagine being responsible for this is the last card grafics driver I just updated. It's a GeForce GTX670.

  How can I get the screens to turn on again when I boot?

  The last time, that he did it today, I just restarted the computer and it worked again, but not this time.

  Thank you in advance for your help!

  Hello

  We are here to help. You can perform the following troubleshooting steps to resolve your concern:

  Option 1: run the program compatibility problems.

  Option 2: set up your bi-ecrans.

  If the same thing happens after the above steps, you can turn off your computer, remove all cables on your pc (including the power cable), wait 2 minutes, reconnect the cables and turn on your computer.

  Let us know how it goes.

• The latitude E6400 LCD is dim/dark

  I have a Latitude E6400 with Vista. When I boot, I see the bios and the running of State Bar. as soon as it starts at the window, the screen goes black/sun. I can still see, but it is very very light. It doesn't matter if it is on battery or AC is fine when I plug in an external display. I tried key fn and arrow making, but which was useless. could the backlit feature on the LCD is dead? any help would be greatly appreciated.

  I am facing exactly the same problem with my computer laptop studio 1555. My research on line up to tell me that this is very probably the inverter which is bad.

  The fact that it has very low picture indicates that the screen is probably ok.

  A possible culprit is the hinge switch that turn off the screen when folded down. If this does not work when you lower and open on the external screen, my guess is that the switch is probably ok.

  The third possibility is the backlight ccfl lamp. What I generally find people reporting is that the screen begins to turn red before the ccfl lamp turns off. If we do not face that then the lamp should probably be ok.

  I'll order a new card of the inverter and replace it and pray with my fingers crossed.

• HP envy 4500: upper part scanning but the lower part of the older scan

  Hello

  I need an explanation of what could of happened to cause this problem.

  I've scanned 4 cheques, but only the upper part of the cheques would be real, the lower part was released as a previous check scanned.

  So basically all 4 cheques are the same except for the date and sequence number which was the upper part.

  That's happened? I'm so confused.

  Thanks in advance

  Hi sandra_s,

  You are welcome!

  Yes, most likely a connection problem, or a driver conflict. One of the two could be the cause of the software behaves the way that you describe.

  If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

  I hope that answers your question!

• My screen is so dark, that I see only the icons by using a flashlight!

  When my mother started her cell phone this morning, the screen came very dark and I can hardly do anything on the screen.  I tested with different settings and colors and brightness change, but not physically, I can't see anything without using a flashlight.  It's as if the backlight went dim or something.

  She uses a Dell Inspiron with Windows Vista.  I'm not aware of any other characteristic that is not my computer.    Please do not hesitate to ask questions and I will do my best to answer or find the answers.

  Please help make my life easier and help me fix his computer.

  I think that you have diagnosed the problem yourself. It's the backlight or the inverter failed. You can check if the cables are loose and you will need to make to a repair shop to get the extract. The only practical way to check is to Exchange in well known components until the problem is located.

  Here is part of a Dell Inspiron manual that shows the wiring:

  http://support.us.Dell.com/support/eDOCS/systems/ins1525/en/SM/display.htm#wp1179838

• I have an event soon wishing prints 4 x 6 given to participants who has a logo provided in one corner and my title generated through the lower part of the rest of the impression. I was able to save the logo and title separately in the identity plate, but

  I soon got an event that wants only the 4 x 6 prints given to participants at the event with a box of logo provided in one corner and my title generated through the lower part of the rest of the impression. At this point, I have both registered in the identity of the Lightroom print module plate and tried to get them in place on a model. He wants me to place one or the other on the model in the picture, but not both (which I need). How can I get both on a template and then save this model so I can just pull up and start shooting prints during the event? I'm not WiFi devices yet so I intend import to Lightroom from the SD through my Macbook card and then wired to an Epson photo printer. Test prints I have the air out well with the box logo or title across the lower part, but I really need both on prints for my client. Thank you.

  alanh9307519 wrote:

  I soon got an event that wants only the 4 x 6 prints given to participants at the event with a box of logo provided in one corner and my title generated through the lower part of the rest of the impression. At this point, I have both registered in the identity of the Lightroom print module plate and tried to get them in place on a model. He wants me to place one or the other on the model in the picture, but not both (which I need). How can I get both on a template and then save this model so I can just pull up and start shooting prints during the event?

  Why not use watermark custom logo and him custom identity plate for the title in the LR print module? You also have the option to add the title at the bottom of the image using 'Photo Info' selection "Custom Text". After installation, you can save this as a new model. Unless I'm missing something, it should do the job.

  Instructions for both here in two separate videos: identity plate "Julieanne Kost's Blog of »

  Here is an example with three used: