Launch date for Cisco switches
Hello
I need the launch date for the following products:
Cisco SB SG200
Cisco SG300 SB
Can anyone provide this information?
Thank you
Tiziana
Tags: Cisco Support
Similar Questions
-
How do I remove the launch date for the safe in FF portable ESR 31
How do I remove the launch date for the safe in FF portable ESR 31. Is it possible that - by pressing the SHIFT key when you launch firefox shows the option of safe mode - off and close the browser.
See also:
-
rrack mounting brackets for Cisco switch SF300 - 48P?
Does anyone know how to get grid mounting brackets for switch Cisco SF300 - 48P?
You might be able to get them through the support of Cisco. Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-m...
-
ESXi - Trunking for Cisco switch
Hi, I'm having a little trouble to create a trunk to a crowd of v4.1 ESXi.
My config on the switch
interface GigabitEthernet3/29
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 100 300
switchport mode trunk
switchport nonegotiate
spanning tree portfast trunkESXi side VLAN ID has been set to all (4095) - side switch and host configurations is passed to the host of vCentre.
Defining the interface of switching on an access on VLAN100 port, the host will stand fine. Problem is that I need another network to be consulted (VLAN300)
interface GigabitEthernet3/29
switchport access vlan 100
switchport mode access
spanning tree portfast
endI am able to allow a second card on the host computer and the whole upward like a trunk as above, seems to work fine, even if I don't have a virtual machine upwards on it yet to test
*
My query is, how can we allow multiple VLANs to an ESXi host on a single card? What I'm missing here...
Thanks in adavance.
Brendan
For me, looks like the vmkernel interface used for the management network is not be marked, as the host responds when you define the physical switch as an access port port in the VLAN 100. So either mark the vmkernel with VLAN ID 100 port or VLAN 100 native VLAN on the switchport physical... (switchport trunk vlan 100 native)
/ Rubeck
-
I would like to know if the compatibility for the storage matrix Dell is updated regularly, especially for cisco switches.
We seek to deploy a few PS6210 with 10G connectiivity and here for use with switches Cisco 4500 X series. However these are not included in the doc. There are a few cisco switches that are the end of life (4948 and some nexus switches).Hello
Yes the guide is updated regularly, usually monthly or updates are available.
Since the x 4500 is not a Nexus series switch, you looking for correct DCB support?
In this case these Dell 'Level 3' offers better support for resonable effort. I'll make sure that use you the latest firmware IOS and EQL. There are other switches catalyst IOS in the guide. Configure it in this sense would be a great place to start. Ideally, the switch dedicated for iSCSI use, not VLANd with other types of traffic.
If you can first test before production, then support can see table diagnosis and SANHQ archive for any signs of network related issues. (retransmit rate and types for example)
Kind regards
-
Plug-and-Play for Cisco Small Business 300 Series managed switch
Nice day
What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?
It seems there are not, the operating system is not the standard IOS I used to.
I would use with ability to bridge the Infrastructure first Cisco PnP.
Concerning
Stone
First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.
Seal a document shows how this is done.
Hope that the information would be useful.
-
Required for NAC firewall ports manager manage/add the Cisco switch
Hello
I am trying to add switches cisco for the NAM, but I am not able to add the switch I get the error "unable to control switch" I tried opening ports 161-162 on the firwall; If I were to allow all traffic between the NAM and the switch, cisco NAM is able to add/manage the switch.
Do not know what are the other ports may be required for cisco NAM for managing the switch?
Thank you.
Hello
As far as I KNOW, only UDP 161 and 162 for SNMP communication ports must be open.
Please make sure that you have configured the correct port on the switch:
(config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp
If still does not, I would check the logs on the firewall for any traffic blocked between the cam and the switch.
HTH,
Tiago
--
If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
-
Compatibility matrix for Cisco Catalyst 3012 Switch Module
Hello
I'm checking the compatibility of the VMware vSphere 5.5U1 Guide and an IBM switch module Part Number: 43W4401 product name: Cisco Catalyst Switch Module 3012. The search of the matrix returns Cisco 1GigE I350 LOM who seems to identify the drivers of Cisco.
Can anyone help clarify and check if this IBM re-branded chassis switch module is supported and to a specific firmware for the switch code? Thank you all.
L2/L3 switches are off-limit of drivers for vSphere hypervisor, so you don't find on the HCL...
Here's IBM BladeCenter matrix interop for VMware:
IBM ServerProven compatibility
and here is the interoperability of the switch Cisco Catalyst 3012 with IBM BladeCenter chassis:
IBM BladeCenter Interoperability Test program
I hope this helps...
-
Configure the VLAN voice and data in CISCO SF 300 8 P
I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:
Data VLAN: default 145.17.59.0/24
Voice VLANS: VLAN 20 172.22.20.0/24
I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.
This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.
Can anyone please guide me / help on this.
Kind regards
A K.M.SayeedHi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.
ID of the vlan 20 voices
You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.
If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them. In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.
These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.
-remember messages useful rate.
-
Configuration Wireless 3G as online backup with cisco switch layer 3?
Hi all
We have an existing GPRS modems for data transfer between 2 different sites, this connection is a bit slow to no more than approximately 114 Kbps, the idea is to add a 3G modem, so the solution will be based on a two-way communication lines which are 3G network and the GPRS network.
The line GPRS will be the main and 3G will be secondary, this redundancy offers a high level of availability of communication between the two sites.
is it possible to configure this redundancy with a cisco switch layer 3? If this is the case do you have a tutorial or a link which explain how to do this work with a layer switch 3 ciso?
all information will be useful for me, thanks
Hello
The config is one provided by anisaini, but you need to change your NAT like this:
IP nat inside source MAIN interface map route x/x main interface
IP nat inside source route-map interface o/o interface secondary SCHOOL
Interior int z/z interface
IP nat inside
int x/x
NAT outside IP
int y/y
NAT outside IP
access-list 99
permit x.x.x.x y.y.y.y where x.x.x.x is your home subnet addresses and y.y.y.y is the corresponding generic mask
PRIMARY route map
match ip add 99
match interface x/x
SECONDARY route map
match ip add 99
game interface y/y
Concerning
Alain
Remember messages useful rate.
-
Lifecycle for Catalyst switches
Hello
I have a client who wants to know what is the life expectancy for switching series of following products:
- C3750
- C3750-E
- C4500-E
- C6500-E
I gave, they want to know if there are plans for the foregoing to be gradually in the near future. If yes - what is the time frame for each? If no - more how many years can they expect the viable product? Similarly, are there offender to expand the range of products for the series C3750 and C3750-E, given the model 'limited' available today?
I couldn't find an other another void / community to post this question. I hope that you can transfer this appropriate to address the BU investigation.
Thanks in advance for your help.
Keith
Keith,
Thank you for your question. This community is for Cisco Small Business products, and your question is referring to a product Cisco Elite/Classic. Please post your question in the Cisco NetPro forums located here: http://forums.cisco.com/eforum/servlet/NetProf?page=main this forum is subject to the subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
Community support space Support SB---> NetPro Forum
-Voice and conference---> UC and video Forum http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748. SJ3A? page = Unified_Communications_and_Video_discussion
-Security and monitoring---> Security Forum http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748. SJ3A? page = Security_discussion
-Wireless---> Wireless - mobility http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748. SJ3A? page = Wireless_-_Mobility_discussion
-Storage---> Data Center Forum to the http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748 network. SJ3A? page = Data_Center_discussion
-Routers---> Network Infrastructure Forum http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748. SJ3A? page = Network_Infrastructure_discussion
-Switches---> Network Infrastructure Forum http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748. SJ3A? page = Network_Infrastructure_discussion
-
Reference Dell OMSA Release Date for vSphere 6.0 ViB
Hello
information about the release dates for vib for vSphere vsphere 6 (OMSA 7.4.1 / 8.0.1 / 8.0.2)
Apart from that... OMSA 8 will continue in two different development branches for T630, R630, R730, R730xd and T430/R430/T530/R530/M630... or will it be a next single version for all serversystems of 13 G.
Kind regards
Torsten
Toki76,
Custom Dell ESXi ISO 6.0 came out 2 days ago. So I guess, from past experience, that the VIB is going to be released very soon behind him, but at the moment I do not see that he launched. I can research to see if I can refine the delivery date well and let you know.
What about OMSA 8, probably a single version which includes the two branches.
-
Why I can't command show running on cisco switch
On a single switch, I found that some commands because they show execution or copy running-config tftp: on cisco switch WS-C2960X-24TS-L does not work it see more below. How I can use the command then show generally. Thank you.
Building1_FAA_6F_SW3 #sh run
Building configuration...Current configuration: 100 bytes
!
! No change since the last restart configuration
!
boot-start-marker
boot-end-marker
!
!
!
!
!
!
end---------------------------------------------------
Building1_FAA_6F_SW3 #copy running-config tftp:
^
Invalid entry % detected at ' ^' marker.OK, so the information you provided in your latest messages confirm that the privilege level you get via telnet/vty is different from the one you get via the console. This is due to the configuration of AAA which applies to the vty ports but not on the console port.
So if you want the same rules apply to the console port, then you must configure the port console for AAA as well.
If you don't want these rules then you need to remove the AAA configurations. The best way to remove these is by typing 'no new aaa - model' However, careful not to lock you out of the unit. Make sure you have local accounts with the privilege level 15 and you also know the active password/secret.
I hope this helps!
Thank you for evaluating useful messages!
-
To the main unit Infrastructure Cisco switch port
Hello.
I had a doubt as to the Port of the Switch in my Cisco Switch for a camera of the first Infrastructure.
This port must be a Switchport to access or a Switchport Trunk?
What is your recommendation on this subject? What is best practice?
Thank you very much.
Access port should work fine. You do not configure a VLAN on the device itself, just the IP address / subnet and default gateway.
Thank you
Ric
-
Switchport security best practices for Cisco IP phones
Hello.
I have some difficulty to understand what the safest method is to ensure a Cisco IP Phone.
Can't get info on how many course connect a switchport and a telephone computer IP Cisco with a daisy chained to him.
The thing I fear more precisely is how to secure against attacks of Double VLAN tagging and COP on this port.
I searched regardless of the possible resource for the answer and you have not found anything useful.
I also have a question regarding port security on a switch: can you set a minimum amount of MAC addresses active and then limit the period of ageing on the MAC addresses on a specific switchport, such that if someone disconnects the phone and sets up a Cisco switch or other device of thugs, then the port should be stopped during the period of ageing.
Let me know, what you would suggest to better secure the hose between the Cisco IP phone and the switch.
Best regards
Casper.
If you see all these as the attack vector for your environment, there are only 802. 1 x that can help you.
Maybe you are looking for
-
using an old iphone when my other is repaired
My 6 64GB iPhone going off for repair and I'll be without it for a week, so I supported everything to icloud. I have an iPhone using 5 temporarily, but one) I don't know what is the size of the phone is so I'm worried if it's not enough for all of my
-
iCloud photo library and the problems of local storage of iOS
I have iCloud library lit with iPhone active storage optimization. However, I still have more than 1 GB of space being taken up locally on my iOS. If all my photos that I take on iOS are automatically sent to iCloud for storing, why is there such a b
-
I'm having some problems trying to plot 3D data. Ideally, I would like to a surface field, but I don't know that I'm going to speak properly. I have three tables 1 d of equal length: x, y, z. The "graphic 3D surface" vi wants entries from: vector x -
-
Updates of BIOS for non-Microsoft users
I have an a6707c HP Pavilion Tower. Everything is stock except for the wifi, the HARD drive and the new drive. 4 GB DDR2 and a 2.40 GHz dual core Pentium with a configuration of Foxconn. My bios had problems, even with Windows. He seems to want to al
-
Black mirror2: I can't open the black mirror game.
I can't open the black mirror game.