Lenovo 3000 n200 - keyboard problem

Similar Questions

• Lenovo 3000 N200 wireless problem

  HY,

  I just installed windows xp sp3 on my Lenovo 3000 N200 laptop, I installed all the drivers and everything except wireless works.

  Wireless light does not illuminate when I move the button 'Activate', only the bluetooth light.

  I went to device maneger and saw that there is a 'mistake' in the network controller. I reinstalled the drivers for the wireless, but it still doesn't work.

  Help please.

  Hi all

  I just installed xp sp3 edition in my lenovo 3000 n200 and yes I had the same problem with the radio. I Googled it and found the correct dirver: driver Broadcom WIRELESS LAN, where you can find here http://consumersupport.lenovo.com/ot/en/driversdownloads/Drivers_Show_236.html.

  1 extract

  2. install

  When installing wireless led light started to Flash and it works perfectly.

  Sincerely,

  lukime

• Lenovo 3000 N200 0769 keyboard problem

  I have a strange problem with the keyboard on a newly acquired Lenovo 3000 N200 0769.

  The laptop came from the work, it had been messed up trying to remove Vista and it would not boot from the CD or enter the BIOS, it was stuck just trying to run Rescue and Recovery more and more without a partition of work service.

  I managed to get Windows7 installed on the machine and it works great except for a number of things.  The touchpad does not work (not recognized by the system).  I suspect the material in this case, so I have a forthcoming replacement touchpad.

  The biggest problem is the keyboard.  It does not at all when the machine starts.  This means that I can't get into the BIOS, and I can't "any key" to boot from a CD.  As soon as Windows (or Ubuntu, I used to help recover the machine) load the keyboard driver, the keyboard to life and it works perfectly (I'm typing this message on the keyboard)

  Because the keyboard works perfectly when the drivers are installed, I am inclined to think that the keyboard material is OK.  With Windows installed, I have updated the BIOS to the latest version, no change to the problem.    I tried using a USB keyboard (before flashing the BIOS), but it does not either until the operating system loads.  I also tried to reset the BIOS using the contact in the hard drive compartment.  This causes the BIOS to complain and offer F1 or F2, but the keyboard does not work, so I still can't get.  I reinstalled the keyboard and the touchpad connector on the motherboard.

  Any ideas?  I would like to replace the keyboard if I did fix it (or I ran out of options!), but I bet that someone else ran into the front.  I tried Lenovo ringtone for support, but when they found it was out of warranty, they said "I'm not allowed to talk to you."

  See you soon

  John

  You have the problem solved.

  I was doubtful touchpad.  AMD got one off of eBay just finished install 10 minutes ago.  The keyboard works properly as soon as the machine starts and the touchpad is recognized and working properly as well.

  See you soon

  John

• Lenovo 3000 N200 - cannot access Rescue and Recovery - MBR poss problem?

  I have a Lenovo 3000 N200 sick who was running XP home. I could not start XP and can only access the Rescue and Recovery utility in the Lenovo recovery Partition that would be to rebuild the hard drive to factory settings IE. Windows XP with no data. I managed to copy the data using a Paragon backup cd and then made the fatal mistake of attempting a repair MBR, which was a very tempting option on the Paragon rescue cd. Now, not only it does not boot to XP, but I can run is even more Rescue and Recovery to reinstall XP which is the problem!

  If I boot with windows install disc and take the option recovery console it stops, statement that "recovery console could not find the hard drives connected to your computer. Setup cannot continue. "

  I was wondering if someone another backup MBR restore could help me with this?

  So, if someone has a Lenovo 3000 N200 work and is willing to try to save the MBR to send it to me, then please get in touch. It is probably useful to make a backup for yourself where the same problems happen to you!  In my view, there are a bunch of programs that backup the MBR for example MBRtool, MBRWizard and so on.

  Any ideas, offer accepted with gratitude.

  Yes I know I could buy the Lenovo recovery disk, but it is a matter of principle for me avoid paying £50 or so if I can avoid it! We'll see if we can help here...

  Thank you

  Simonides

  I am pleased Andyp!

  The solution was to set the primary partition to inactive and value the recovery partition Active, then restart and use the Lenovo Care button (now finally works) to access the function of recovery so I could return the laptop to factory State.

  No doubt there are plenty of ways to do it, but the approach I took to solve this problem is released under

  1. use another PC to download Paragon backup and restore (I actually used the trial edition now but the free edition may have a similar feature)

  2nd burn a CD bootable backup and recovery 10.0.

  3. start the CD Lenovo, and after a long wait, a menu should appear with 11 options, the first of them being Paragon backup and restore.

  4. Select Paragon backup and restore.

  5 select properties in the pick a task window and you will see two partitions, a big enough (in my case Go 143, called Preload) and the other is quite small (6 GB called SERVICEV001).

  Note: this is an opportunity brilliant to use the Back Up Partition option to make a backup on external drive USB of the two partitions as the reconstruction of the hard drive with Lenovo Care button you will lose all data.

  6 right-click the partition preloads and select Edit and set idle

  7. made the SERVICEV001 partition right click and select Edit and set the Active

  8 remove the backup and recovery of CD and put it somewhere safe

  9. restart the PC and Lenovo Care button (might be called something different) should now work, allowing you to restore the hard drive to factory settings which will erase all data of a personal nature. You did a backup?

  10 Windows should then start as usual, reinstall Paragon backup and restore, and restore your data.

  Finally, look at this as a lesson to

  (a) you get a writable DVD and use the Lenovo menu under windows to create a floppy disk from Lenovo rescue and recovery started.

  (b) use Paragon or equivalent to create copies of images of each partition and ordinary differential copies of the primary partition.

  I hope this will help other owners who have a hidden rescue for example partition. IBM and HP and would like to receive feedback.

  Finally, I must acknowledge assistance patient e-mail provided by Taisia Smirnova Paragon support by offering me this solution.

  best, Simonides

  (If you found this helpful please click on the star to give me a point Bravo!)

• Problem with CD/DVD-unit of Lenovo 3000 N200

  Hello

  I have a problem with my Lenovo 3000 N200 newly purchased. The CD/DVD-unit worked from the beginning, but now is not present among the readers, that I can see at the opening of 'computer '. The player is visible is the C drive ("SW_Preload (C'"). ")

  The CD/DVD unit actually reads the CD: s or Swedish I insert, but nothing more happens and "Microsoft Management Console" device CD/DVD-("MAT ** bip ** z A DVD-RAM UJ-850 ATA Device» apparaît, mais avec un petit point d'exclamation marque sur elle.)

  I sought unity for readers, but have found no and readers used are apparently own Microsoft driver for CD-ROM units ('C:\Windows\system32\DRIVERS\cdrom.sys', 'C:\Windows\system32\Drivers\GEARAspiWDM.sys' and "C:\Windows\system32\Drivers\PxHelp20.sys").

  The thing I did at the same time the CD/DVD has probably lost its good driver or something was to install Norton 360 from Symantec.

  I would really appreciate help with this question.

  I did, as a last resort, try the solution pa Cecilia on IDG proposed, tinkering in the registry in Windows Vista.

  I didn't like the idea at all, because I thought it was just something I have to do if I had been messing around in the registry or had done something 'strange' (such as actually Windows Vista installed myself, or upgrading or uninstalling drivers important etc) but at the end of the day, he worked , and it was much easier that I well during playback

  Excerpt from Microsoft technical support:

  "To resolve this problem, remove the affected filter drivers. To do this, follow these steps:

  1. Click Start

• 3 beeps on Lenovo 3000 N200 starts

  Bought a lenovo 3000 N200 on eBay that was dead, looked as if it was probably a failure of the motherboard to nothing lit up.  Got a 2nd motherboard user with the same number of eBay and mounted FRU 41R7886, now when I turn on the laptop the drive light lights for a few seconds, after he died, I get 3 beeps, cooling fan seems to stay on and there is nothing on the LCD or on an additional screen that I have connected to the laptop. Tried to remove the DIMM 2 and turned on again and the symptoms are the same as before, except no beeps. Can anyone help as to the likely cause of failure? Thanks, Dan

  Problem solved, thanks for all the great answers.

  I tried the memory two sims in my Lenovo 3000 C200 laptop and got exactly the same symptoms, dead PC and 3 beeps, discovered that one memory sims I was using was defective. This replaced and Lenovo 3000 N200 now up and running.

• Lenovo 3000 N200 on the habit of power and shows no lights

  Hi all

  I have a Lenovo 3000 N200 laptop. One day he just off its autonomy while watching a video, and now shows no signs of life. Used to power on, no light when it is connected with a power supply, nothing.

  I tested the power supply and tried another new and get the same result. So I don't think that the battery/power supply is the issue.

  I have a feeling that it is something more serious, the laptop is out of warranty and IBMs fresh out of warranty are stupidly high. If anyone knows what could cause this problem and if it is possible to repair with a spare room (off ebay or elsewhere), I'm able to disassemble the laptop and replace a part.

  Thanks for any advice.

  Bass sounds.

  Some say remove memory and see if it gives an indication

  of life, like any beeps at startup.

  Try without battery, try to unplug it, remove the battery and press and hold the

  power button for 30 seconds and plug in again etc.

  Try to remove the hard drive, but this looks like a dead motherboard

  If you have any sign of life after trying everything you can think of.

• Lenovo 3000 N200 display lights after standby or cover open

  Hello

  I have a Lenovo 3000 N200 (0687-A11) with Windows XP SP3 (I downgraded it from Vista to XP myself) and the following problems occur;

  In Windows XP when I close the lid of the system goes into sleep mode, but open the lid again starts the system but does not turn the screen. I have to press the power on button for a few seconds and turn off the system and back on again, which then leads to the screen working again.

  When I put the computer power options to do nothing when I close the lid, the screen turns off and light up again.

  I also connected the laptop to an external monitor and then put the laptop to sleep, but then the external monitor does not turn on either.

  This problem also occurs on laptop my father, a laptop HP Compaq 6710 b with Windows XP (downgraded from Vista to XP also).

  Any type of help is considered! I asked this question on many forums and havn't received a response...

  Any help will be appreciated,

  Kind regards

  Dean.S

  Hi all

  I HAVE NOW FIXED MY PROBLEM! IF WINDOWS XP is not SO SHIT NOW is jenak37?

  What I had to do was to reformat and reinstall windows xp and now it works fine. I installed all the drivers and my usual programs and now it goes into sleep mode & wakes her up with success.

  Thank you

  Dean.S

• Lenovo 3000 n200 ram expansion

  Hi, I just bought a lenovo 3000 N200, it comes with 1 GB of ram... the thing is, I want to extend to 3 GB. When I bought it, they told me to come back Monday to install an aditional GB (you was a combo) and a promotion of lenovo, I won another GB (hu a little lucky!), can it be upgraded to 3 GB of ram? and if so, should it be 1 GB per slot or it takes 1 GB + 2 GB (2 slots)... Thank you very much in advance for your answers!

  It would probably be the case. But for normal use, 2 gig should be easy to do.

• Computer laptop Lenovo 3000 N200 that does not start as a system file is missing or damaged:

  «I have a laptop Lenovo 3000 N200 that won't start as "" Windows has no start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM "»»

  Rescue and Recovery Tools will allow me to restore the hard drive to factory settings, but I prefer to back up important data first. Rescue and recovery apparently allow backup and pays the appropriate folder / structure of files, but the "Start" option is grayed out.

  Then I tried to boot from Windows XP CD but it signals that it has no hard drive, although Rescue and Recovery can apparently go to folder/file structure.

  How can I move it please?

  Thank you very much - Simonides

  all sorted out now... see http://forums.lenovo.com/t5/Lenovo-3000-and-Value-line/Lenovo-3000-N200-can-t-access-Rescue-and-Reco...

• Lenovo 3000 N200 0769 - could I strap a video about this card?

  Hello

  I know that this question is asked before, but I have not found an answer that is relevant to me. I have a 3000 N200 series, version 0769. the original specs are: Windows Vista Home edition, processor Intel Celeron 550 2.0 Ghz, 1 GB RAM, 160 GB of HARD drive, video card integrated in the Chipset Intel 965 M (64 MB dedicated).

  Now, since the original specifications, I've upgraded to another (identical) 1 GB of RAM and a T7100 Intel Dual-core clocked at 1.8 Ghz CPU, and I am now running Windows 7 32 bit. The reason for which I've upgraded to the T7100 is because I saw a variant of the N200 with this CPU.

  My question is: am I able to Update my graphics card? I know that some 0769 variants have an another version of the graphics card, I think than a 256 MB GeForce. Can I get something like this up on my own? Or I hit the wall when it comes to upgrades?

  Please help me, I need a better graphic performance ASAP (work stuff). In addition, I don't have the money for a new laptop (possibly a new card mother or graphics card, but no more than that).

  Thank you!!

  Well, you can't go graphics without Exchange the
  motherboard with Nvidia graphics, which also
  had a different radiator Setup to handle the additional heat
  GPU. So I doubt a swap would work without modification.

  Swaps the motherboard used, IMO, are not profitable.

  RAM can be up to 4 GB, with 3 being a good compromise,
  and cpu Core 2 Duo T7500, which would be too minor for
  a helping hand to the T7100, unless you can find a good deal.

  Probably other processors that were also added later.

  In my opinion? Put the money towards a good laptop used
  with the specifications of need/want.

  Oh and the weak bios? There are a few bios modding communities

  There, but it's a high risk of adventure! See this post for an example:

  http://forums.Lenovo.com/T5/IdeaPad-Y-U-V-and-Z-series/Y460P-won-t-boot/TD-p/776363

• Wich refers to a Lenovo 3000 N200 fan?

  (sorry for the bad English, I'm not English speaking people)

  Hello

  I have a Lenovo laptop 3000 N200 0769-A44 (S/N xxxxxxx 07/11).

  I have a noise from the CPU fan. I want to change the CPU fan, but I can't find the right reference.

  In the part of the system, 0769, there are 2 References: 41W5225 and 41R7795.

  The fan, there's the S/N ATZI8000700M1.

  Can you tell me which of the 2 references is right for my computer?

  Thank you

  Note of the moderator; s/n, under the direction of protection own members

  Intel graphics card: 41W5225
  NVIDIA graphics: 41R7795

  I think that yours has Nvidia?

• Lenovo 3000 N200: off suddenly :/

  I have a Lenovo 3000 (TYPE 0769 - BEG S/N *) that has worked well until recently.

  For about 4 weeks the laptop started acting on me, so he could all of a sudden stops on me. No warning.

  First I it might have something to do with the heat, but I realized that sometimes the laptop runs EVERYDAY non-stop without going out once. Other times, the laptop is turned off for days, I start it and after 1hrs work or then: BOOM. Everything stops.

  Anyone know of a hardware problem on this model?

  Thank you for your help.

  Serial number deleted

  manuals:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-63486

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-67857

• PROBLEM LENOVO 3000 N200

  Have not used my laptop Lenovo for 2 weeks now ' coz I don't know how to resolve the startup problem:

  When I turn on the computer the monitor bed:

  "V.10.0.9 UNDI Broadcom PXE - 2.1.

  Copyright (c) 2000-2006 Broadcom Corporation

  Copyright (c) 1997-2000 Intel Corporation

  All rights reserved.

  PXE - E61: Media test failure. Check the cable.

  PXE - M0F: Exit PXE ROM. Broadcom

  Operating system not found. »

  I tried to run the Vista recovery disk for the recovery of the o/s, but after the execution of the disk for the recovery of the o/s I see on screen a comment (not exact wording): "partition not found; Repeat the process.

  SOS! What for.

  Hello everyone.

  I wonder what you might be able to help me regarding my problem starting.

  How about suggestions from the team of Lenovo (calling Mark Lenovo and his support team).

• Help, notebook 3000 N200 keyboard is crazy!

  N200/3000 notebook my wife just ran out of warranty and the keyboard is crazy.  I checked the number and caps lock, ran the diagnosis for keyboard PC Doctor.  went to Lenovo support/downloads.  But I'm afraid to download the new bios.  I have never do these myself lucky.  Turns into a nightmare.

  These are anyway, following symptoms:

  -the BACKSPACE key does not work

  -space does not work

  -below left is pressed, the right is the result on the screen:

  y gives "yn".

  n gives "yn".

  t gives 'tb '.

  b gives 'tb '.

  -  /     gives                    "[/"

  -  [     gives                    "[/"

  -BACKSPACE will remove the letter just before but not anymore

  These are the only keys that I found the problem with until now, but they make it unusable. Can anyone help.

  Thank you

  Dean

  -

  There is no easy way to test it.