Lenovo M91p desktop does not boot with the new graphics card (Blank don't screen no BIOS)

Similar Questions

• Does not start with the new graphics card

  Hello. I have a P7-1058uk Pavilion Cleveland-GL8 motherboard with integrated graphics.

  I bought a new monitor that has resolution 2560 x 1440, equal the integrated graphics card can face if tried to to level with a Gigabyte GT630 card.

  When I start, I have now the chance to the blue HP screen but not more details. If I start with F10 or ESC key, I get a black screen instead. Whatever it is, I am asked to press ESC to enter in the start, but by pressing on the button has no effect and the computer just hangs. There is a cycle repeated very quiet click that sounds like the disk drive HARD trying to start then stop

  If I remove the graphics card and connect the monitor to the integrated graphics card then all's well again (but limited to the resolution 1920 x 1080).

  Perhaps foolishly, I assumed it was a problem with the residual power (300W) and not enough punch power to run the HARD drive. But who, after having upgraded to 650W it makes no difference. I also tried to download the NVidia drivers but it won't let me install because I can't get the computer to work without the graphics card and Nvidia install it because it cannot detect the hardware.

  Any ideas/help would be appreciated.

  Andrew

  You can have one of these motherboards that are not happy with NVIDIA graphics cards.

  This may sound a little weird, but it happens.

  The other possibility is that you have damaged your home x - 16 PCI Express by installing a map requiring more that the installed power supply has been able to provide.

  Kind regards

  ERICO

• Satellite A110 - switch WiFi does not work with the new WiFi card

  Hello everyone

  I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

  New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

  Help, please

  Hello

  Do you have also enabled the WLAN functionality by pressing FN + F8?
  Check it!

  In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
  So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Computer does not start with the new video card

  Hello

  I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

  The video card is
  Sapphire ATI over-pants 2460

  I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

  It seems to me to have the latest version of the bios and windows 8

  What can I do else?

  Thank you very much

  Best,

  Korhan

  Hi JM,

  Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

  Your PC comes with one of the following built-in Intel graphics drivers:

  • Graphics Intel HD 4400 (GT2)

• Flight of blackBerry 8330 Smartphones, Desktop does not synchronize with the new phone

  A kind person recently broke my window of the car and took my 8330.

  I regularly synced my old phone using Desktop Manager.

  Switch device Wizard wants my old 8330 connected to synchronize new 8330.

  Of course, I don't have the old 8330.

  I don't know that I'm missing something here.

  Can anyone offer assistance?  Please, I beg you!  I'm dying here.

  Thank you!

  So good news.

  Connect your current device to the USB > PC.

  Open Desktop Manager > backup/restore > advanced.

  You should see the IPD backup on the left pane information and the information of the current device in the right pane.

  If the left pane does not, above this window, choose file > Open and navigate to this known IPD file. Load it.

  Now, you can choose one by one or all THE items in the list to transfer to the new device. Highlight each database you moved to the new device and click the right arrow environment to move these data.

  Follow the prompts which if ensuits and you'll be good.

• HP laserjet p1102w: wireless printer does not work with the new wireless network

  My office moved recently and we have a new wireless network. My printer always wireless worked perfectly on the previous network, but it does not work with the new network. I get a message "the printer is offline. I don't know how to reconfigure so that it detects the new wireless network. Can anyone help? Thank you

  Hi Shlomi,
  Thanks a lot for the info. I'll give it a try today...

• IR remote control does not work with the new imac

  IR remote control does not work with the new iMac. From 24 "2007 machine to last 27"

  Correct, because Apple no longer includes the IR sensor in newer models

• In my laptop that is Explorer.exe does not load at startup on my account, his work with the guest account. Also it does not manually with the new process. Kindly help out me

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: in my laptop is Explorer.exe does not load at startup on my account, his work with the guest account. Also it does not manually with the new process. Kindly help me.

  I have seen at redistry Edit it's explorer.exe in winlogin sell attribute.

  Hi HiteshAstan,

  one) don't you recall making any changes to the computer before this happened?

  (b) what exactly happens when you sign in to your account?  You get a specific error message?

  Step 1: Let us check if the problem persists in safe mode

  Access the menu advanced startup options by turning on your computer and pressing the F8 key before Windows starts. In the advanced startup options select safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

   

  If the problem persists, you can deduct that the user account is corrupted

  Step 2: Create a new administrator account and then try to repair your user account

   

  Create-a-user account

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  After the back if you have any questions

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Widget does not now with the new Muse update from today

  Hello!

  My widget I bought MuseGrid "Lite and iFrame generator of widgets.

  Does not now with the new Muse update from today?

  So what to do?

  Many widgets from third party that reached deep into the code generated by Muse may not work with the changes that were necessary for the delicate design. You will need to contact the source of the widget for more information about an update of the widget version.

• 128 - GB MicroSD card does not work with the new Clip +.

  My old Clip + (black, 8 GB) was getting very long in the tooth, so I ordered a replacement off Amazon.  As far as I know, it is identical to the old, but a very unpleasant difference is presented - it does not work with the MicroSD card which has been a huge part of why I got a Sansa at all.  He acknowledges, but after a media updated I'm lucky if more than one album appears.  And that's what's so crazy!  You just blow through the update in a few seconds, and when I navigate on the map, there is nothing or a handful of albums random, orphaned.  That's happened?  I updated the new Clip + for the current firmware (as I had done with previous); I made sure to reproduce all the parameters that I would be put in place before--I can't imagine what could be the cause!

  Treats quick closing:

  The card is formatted in FAT32 with the same sector size in storage aboard the player (32 768 bytes).

  A 64 GB card format works even without any problem.

  I tried to update the media in MTP and MSC mode; the problem is the same in both.

  There is ample space for MTABLE. SYS - I have not yet loaded all the music on the Clip + itself.

  Rockbox plays the card without problem, but the sound quality is horrible (at least on this player; I'm sure that other versions sound best), and its interface is a headache.  No thanks.

  HM.  Looks like to run CHKDSK /F on the map the problem resolved!

• Utility HP does not work with the new update of Mac software

  I downloaded the latest version of the software for my Mac and now utility HP will not work! Any advice? Thanks, Chris

  Hey Chris. Looks like you may have the old software out there which is not compatiable with the new version of Mac OS X. What I would do is a complete uninstall of the HP software you have. Let's try this:

  We will uninstall with the option 'raccoon' like this:

  1. go in Applications/Hewlett Packard / click on uninstall HP and click on continue

  2. Select your device in the left pane
  3. hold the keys Ctrl, Opt and Cmd and click on uninstall
  4. There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  5. click on continue and let it finish

  Now run a software update. Before doing the next step make sure you connect your printer to the computer through USB. Then click on the Apple in the upper left corner of the screen, then clicking on software updates.

  If my instructions don't do because here's a little video to help out you:

• Qosmio G10 with the new graphics card and pcb - CD update tools do not work

  Hello world

  I hope you can help me. Before a few weeks, I received my Toshiba Qosmio G10 return of aid, because the laptop no longer works. So I get it back with a new graphics card and a new PCB. With my laptop I have a CD called the update tool CD and a sheet of instructions, where it says to start with this tool CD-Rom update after you have installed the Windows with the reovery CD.

  So I did, but when I know the update tool CD to put in and I start with it, the computer installs something, but after a short then it is a message that it is a different model and that I have to put a button to close Notepad. So I did it, but Windows does not start.

  Why is it so? I had done everything that has been said on the instruction sheet.

  Please help me

  Hello

  It will be interesting to find more information on this CD-Rom tool update. Are there tags Toshiba? Can you please write what is described here?

• Inspiron 530 Win XP Home does not start with the TrendNet wireless card

  I just received 5/1 a refurbished Inspiron 530 530 Mini-Tower desktop: Intel Core 2 Quad processor Q6600 (8 MB L2 cache, 2.4 GHz, 1066FSB) Genuine Windows XP Home Edition. The PC didn't have any LAN card and I intend to use a working adapter TrendNet (COMPUSA) 54 Mbps Wireless G PCI I used very well with my old 4300 Dim run also Win XP Home. However, after that I booted up the new PC with the first series, I stopped him. I then opened and installed the card wireless in one of the 2 empty PCI slots. When I turned on the PC, surprise! The PC wouldn't start - it kept beeping with the glowing orange of front power button and turn off every two seconds, I then read the Inspiron 530 manual means that the motherboard has detected an error. Hello. I checked.

  I searched other posts in this forum and I've seen a few references to the boot configuration verification. However, installation of starting my PC doesn't have an option related to the wireless adapter.

  Someone help me please fix this error. I intend to reconnect the card on my old PC wireless again and start just to prove that the card is always good. I only removed a card video of him and the rest of the asis. (I've not carpet in my house is that reduces my chances to have fried the card when you remove or install.) I also touch the chassis of the PC before doing anything.)

  
  

• HP Color LaserJet CP2025n Prin: I need to download the older driver because a program does not work with the new driver

  Where can I find the olderdriver that I can use windows 64 bits 10,

  because a program does not with the new driver.

  The year may be 2014 or almost.

  Your Timo

  @tisalmet

  Thanks for the reply with the details,

  You can activate the Device Manager to view hidden devices by following the steps mentioned below:

  To work around this behavior and display devices when you click Show hidden devices:

  1. Click Start, point to programs, point to Accessories, and then click command prompt.
  2. At a command prompt, type the following command and press ENTER:

     Set devmgr_show_nonpresent_devices = 1

  3. Type the following command a command prompt and press ENTER:

     Start devmgmt.msc

  4. Troubleshoot the devices and drivers in Device Manager.

  For more details: click here

  Uninstall all software and drivers for printers:

  When you need to uninstall a driver completely, the best and safest method is to use the uninstaller of the device (if it has one). If you have added the device to your system with a Setup program (as is the case with most of the graphics card and sound card drivers, for example), you can uninstall it as you would any other program.

  1. Click Start, type uninstall program, and then press enter.
  2. In the uninstall window, which appears, scroll through the list and find your device or drivers. Double-click the entry to start the uninstall process.

  Sometimes devices will not have an uninstall program or the uninstall program will not appear in the list. In these cases, you can use Device Manager to remove the driver completely.

  1. Click Start, type Device Managerand press enter.
  2. Find and double click on the category of the device you want to uninstall (for example, the graphic card would be listed under display card) driver.
  3. Right click on the device, and then click Uninstall.
  4. Windows prompts you to confirm the removal of the device. Click OK to remove the driver.
  5. Once the uninstall is complete, restart your computer as soon as possible.

  Once the above steps are done, click here to download the full software features for your printer and follow the Setup process to start to use your printer again.

  I would like to know if these measures worked for you.  If they did, it's great!  Give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers!
  Good luck.