Lenovo Y40: Must only press the power button two times to turn on

Hello

A few months ago, I bought my Lenovo Y40 on the Lenovo Web site and recently, to turn on, I have to press the power button twice. When I press that once, the Lenovo logo is displayed on the screen, but after 2 seconds it turns off. On the second attempt, finally the laptop turns on and the windows is started.

In addition, rarely the phone stucks on the lenovo logo screen, is necessary to contain the power to reset.

Someone had some problems like these describe above?

Thank you.
Pedro Lopes.

Hello

I contacted Lenovo's Support and they recommended to perform a full recovery of the system. Apparently, it worked because I did not suffer these problems since I got windows. Probably, there was a problem with the partition that has been responsible for the initialization of the system.

Thank you, Pedro h. Lopes.

Tags: Lenovo Notebooks

Similar Questions

  • 15 170tu ac: I HAV to press the power button several times to start the laptop...

    I HAV to press the power button several times to start the laptop... works well with the power supply on.

    all My drivers & bios is updated... but when I opened the lid... I HAV poer press several times the button and he then began 4-5 min.

    Hi @Vishalwagh123,

    Welcome to HP's Forums a great way to get help. It's a great place to find answers and advice! Thanks for the post.

    I understand you have questions turn on/off the device and you must press the power button several times for him to start. I'll be happy to help you.

    Please try these steps first. Perform a hard reset.

    • Steps to do:
    • Turn off the computer and unplug the charger. Then remove the battery.
    • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
    • Replace the battery and the charger plug it back. Try to turn on the computer.

    If it fires up immediately the issue is resolved. Otherwise, try to turn on the computer without the battery and check that it works immediately.

    In your message, you said that it works very well with the charger. However, I need more clarity here to help you better.

    It works immediately when the adapter is connected and the power button is pushed only once?

    If you again press the power button several times, it may be a faulty power button, and you will need to contact the hotline at the service of the unit.

    Let me know what happens when you try to turn on the unit without the charger?

    Visit this link to contact support phone:

    http://HP.care/2bjG4nE

    Hope the problem is solved without hassle. Please keep me in the loop.

    Take care and have a week Holy.

  • Help - HP Pavilion a6030.uk desktop computer. Have to press the power button several times to start?

    Hello

    I have a HP desktop computer. The model is HP Pavilion a6030.uk, Opertating system: windows vista.

    My computer has had no problems at all until yesterday for some reason, I had to push the switch several times to start until he finally turned and did normal starts. As I would press the power as normal to start button, but all of a sudden, it turns off after about 2 seconds and so I would tap on the switch several times and each time it will not start and turn off, then the power button could be pressed again until it would finally turn on and start and run as normal and seems to work correctly. And it was the same thing today, I pressed the power button mutiple times (for example 6 times) until she finally started as usual.

    Savvy/computer im not very well informed or wise in this area, please someone will help me and give me some advice/help to fix/resolve this problem.

    Thank you for taking the time to read this and any help would be appreciated for this problem.

    Thank you.

    Vonbon90, welcome to the forum.

    When I see these symptoms on an old computer, I think it may be a power supply (PSU) failure/ing.  Here's a guide that will help your troubleshooting it.

    In addition, you could test the memory.  This can be done by removing all modules of memory and replacing them one at the time and start.

    Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

  • HP Slate 6, (problem: do not turn on the display, by pressing the power button once)

    A month ago, I bought the HP slate 6. The screen does not light by pressing the single time power button. But if I press the power button three times, then it lights. I also make sure that the switch has no problem. I think it's a software problem not hardware.

    Do not forget that I have improved my slate to kitkat. This problem alone caught up in not before Kitkat.

    Best wishes for you

    Topic: Alxhan cc

    Thanks for the info!

    Usually, if a factory restore temporarily solves the problem, but it returns that it is because of the apps to steal resources.

    Try going through this guide that will give you some useful tips for monitoring resources and reduce delays in system:

    5 common causes of lag Android devices (and correct)

  • Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

    It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

    I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

    If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

    Thanks for your help.

    Damicon999 wrote:

    Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

    no chime, black screen, that's all.

    I don't think they are infected.

    The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

    No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

    In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

    Genius of booking http://www.apple.com/retail/geniusbar/

    Online https://getsupport.apple.com/GetproductgroupList.action

    check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

  • Help! My ideapad s110 turns on if I press the power button

    My lenovo ideapad s110 lights when I press the power button. But when I press the Quick Start button on it powers. And it only happens when I have not plugged into the battery adapter. When plugged in the power button works. What could be the problem here?

    Hello

    Please contact the slot support to have the machine checked in the service center

    Thank you

    Alaa

  • Problem intermittent boot Tecra S2 after pressing the power button

    Hi all
    I have a Tecra S2 with the 6600go GFX card.
    The machine is large but presents the following problem.

    After that the machine was interrupted for a while it will start not reliable.
    You press the power button. Either as soon as you release the power button or a second later (changes every time) the green power light comes on. The fan spins at high speed then slows down to a crawl a few seconds later (as usual) but LCD does not illuminate.
    Also when it does not start USB devices are not initialized (I have a product key dongle which will flash if it is not initialized - when you start the laptop properly this dongle on continuous - a normal start, it is initialized before the ramtest BIOS)

    I've updated the bios a couple of times - it is now 2.4 (I noticed the power button timings were changed in the V1.9) but this has not solved the problem.

    I tried to start on the current with battery removed, ca battery & battery only - the result is the same.

    I can start later button power until the laptop off, wait a few seconds and then try to get back to work.
    After several of these cycles, it will begin eventually to the top. Recently, it seems that it took several attempts before start-up.

    If I have used the laptop for an hour or two and then turn it off it will start almost always a first time.

    If I put the laptop to sleep (orange slow flashing power LED) then half the time that it will continue when you press the power button - the other half of the power LED will switch to the green but the LCD display remains inactive & I switch the power button.

    Any help or advice would be welcome.

    Thanks in advance,
    Robin

    Hello

    This seems very odd.
    First of all: you can boot from USB only if the floppy drive is attached.
    You can boot from these devices USB-drive floppy/disk HARD/ODD/LAN.

    In my opinion the other unit starts the sound not as issues not a software problem.
    I think there could be something wrong with the hardware. But it is not easy to say what it could be exactly.
    You know, the look on the material is necessary.
    I recommend you contact Toshiba service partner in your country.
    They have much more experience in such cases. Guys can run tests and then can give you correct information about the failure.

  • Satellite L550-1CW does not start by pressing the power button / stop

    I have a Toshiba Satellite L550-1cw that won't start, lights up when I press the power button all the lights at the front, the fan starts and he is looking for a HARD drive for about 2 seconds and then stops.

    I tried a new HARD drive, but the same happens.
    I was told that all this must be ignored and buy a new one that is not an option.
    I love this laptop and want to run again as this is the best I have ever owned.

    Help, please

    Andrew

    Can you give us more information on this vulnerability?
    You see something on the screen after pressing the power button?
    You can access the BIOS by pressing the F2 key immediately after switching on the device?

    Despite this whole issue, I think that if nothing is visible on the screen it could be a serious problem with one of the following: RAM modules, motherboard, CPU/GPU.

    From my experience the RAM memory modules are not very expensive (2nd hand might be good enough) and the replacement isn t very delicate in the case where the faulty memory causes this problem, the laptop could be set for a little money.

    But in case of problems of motherboard, laptop repair procedure could be very expensive.

  • I can't start with Satellite P10 by pressing the power button more

    I can't start my Satellite P10 by pressing the power button more.
    Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

    I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

    So it must be a problem with the key.
    No idea what to do?

    Thanks for any help

    The best.

    Tobias

    If it s a button or a power supply electronic problem, then you can't do anything.
    In this case assistance by the technicians of laptop would be necessary.

    But the next time that you should try this option if the laptop turns on not;
    Remove the battery and unplug the AC adapter from the laptop for about 30 min.

    After this short period of time to reconnect the two parts and check if the laptop could start.

    Good luck

  • When my computer goes into sleep mode, I have to press the power button to turn it back on.

    original title: sleep/hibernation

    When my computer goes into sleep mode, I have to press the power button to turn it back on.  I used only having to press a key on the keyboard.

    Can someone tell me how to solve this problem, as if it was before?

    Well, on the theory that your computer is awkward, try to change the settings to another thing and OK your way out the control panel.  Then go back and put them in the way they were and OK your way out.  Occasionally, it will reset the internal parameters and things can return to normal.

    HTH,
    JW

  • P1102 - why I have to press the power button before printing

    Hello

    I was wondering if anyone else knows how to avoid this problem. We have a P1102 connected via USB on Win 7 64 bit.

    Is there a setting somewhere that allows us to not have to press the power button on the printer before printing. It is now connected to the pc. The pc is turned off at night.

    It is very annoying to have to push the button before printing. This may sound trivial, but our old Hp laserjet 1100, only has been replaced with this P1102 as the new pc have no place for a parallel port card, and you never had to press the power button before printing with that, this feels like a step and is very disappointing.

    Thanks in advance.

    It seems that the printer software is not save the auto power off feature is set to never.  I would definitely try update the internal firmware of the printer to see if updating automatic stop is set to never work.

    Click here to access the download page for the Laserjet Firmwares.  Select the P1100 series in the drop-down list.

    This should be done so that a USB cable to connect the printer and the PC.  I would like to know if the firmware is able to get the printer to stay alive.

  • Press the Power button twice at startup?

    On my new E530 I just realized I have to press the power button twice for the laptop start. At first, I thought that I tap it enough hard or the calendar has been disabled or something, but after many tests I came to the conclusion that it is in fact mandatory that I press the power button TWICE in the order the laptop to start.

    My question is, is this normal / design?

    Google gave was contradictory and inconclusive answers:

    http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/ThinkPad-edge-E420s-start-up-button-issue/t...

    http://forums.Lenovo.com/T5/ThinkPad-edge/power-button/TD-p/307704

    A credible person can sound here?

    Much appreciated and thanks in advance!

    Hey, Gleipnir,.

    When I pressed the button of power quickly as that, in my view, your description it would take two thrusts to get to power be as the first was not strong enough to register. I believe that this does not work as expected and you should not be concerned.

    Best regards

    Hiro

  • I reset my Apple Watch and I can no longer use it, whenever I press the power button, it gives me the sign of loading

    I reset my Apple Watch and I can no longer use it, whenever I press the power button, it gives me the sign of loading

    Hello

    Try restarting your watch force: press and hold the side button and the digital Crown for about 10 seconds, until you see the Apple logo.

  • Why Satellite Pro A300 does not start when you press the power button?

    Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

    In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
    Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

    What should I do to get a normal departure procedure?

    When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

    When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
    The same thing happen on my Satellite A300.

  • Satellite A200 23W stop seconds after pressing the power button / stop

    Hello all :)

    I just bought a laptop Toshiba Satellite A200 23W a few hours ago.
    I turn it on and let it complete the installation of Vista.

    After the installation of Vista finishing it asket to resturn laptop and from that moment, the laptop is "dead".
    After pressing on restart the computer (from Vista) computer turns off without problem, but he never did it again!
    After a few minutes of waiting, I tried to start it by pressing the power button.

    Now when I press the power button, I can hear the HDD work and most of the time until I see something on the screen of the laptop computer stops!
    Now, I noticed that both the battery indicator AND the DC IN light are hot flushing and stop Flash at times.
    Reading the manual, I guess that the DC IN indicator should Flash in all not well.

    I tried to uninstall the battery and try to start the laptop, but in this case I can't even listen to the HDD, commissioning!
    I try to unplag and replag (on the laptop as well as Jack) power cable but again no result.

    Any ideas of what past?
    Thank you very much

    I don't know what the problem is here and, in my view, should not be so important to you. Contact your dealer as soon as possible and to talk with him. Explain the situation. You will get may be new notebook. Otherwise, please contact the nearest authorized maintainer and let check your laptop.

    The laptop is brand new and it should work. Please do not wait too long.

Maybe you are looking for