Lexmark rhow bar I know if my lexmark all in one p4350 printer is compatible with this computer

Similar Questions

• Windows 7 pro deactivation lexmark all in one for pilots.

  I have 2 different Lexmark all-in-one printer / scanner. Windows 7 pro in just the last 2 weeks, via a download/update made my Lexmark x 2470 useless, corrupt some thing in the firmware and disabled drivers for my Lexmark 4530 thus making it unusable. Anyone having the same problems, have their software Lexmark corrupted by Microsoft updates?

  Hello

  Please contact Microsoft Community.

  Let us know the exact error message you get.

  Make a test with the steps below:

  Step 1:

  Try to run the troubleshooting of the printer utility.

  Click Start.

  In the search bar, type troubleshooting.

  Select the printer in the list and click Next.

  Step 2:

  Turn on Auditors invited on all computers.

  Step 3:

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  In Windows 7, go to control panel > everything in Control Panel > network and sharing Center. Click on "change the advanced sharing settings. You don't want to use the residential group unless you have all Windows 7 machines. If you do and you want to use the homegroup, see Windows 7 Help & Support. Otherwise, in sharing advanced:

  Turn on WE network discovery
  Turn ON file and sharing printers
  Put IT in the section sharing public folder
  Turn ON password protected sharing

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, running on Windows 7 sharing files and printer as above will take care of this for you. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine. With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. Don't STOP FIREWALLS; CONFIGURE them PROPERLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT CREATE PASSWORDS, EVEN IF ONLY the MOST SIMPLE . If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  Start > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers on your network are XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. In Windows 7 I usually share the Desktop of the user and the Public directory.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers.

  How install a printer connected locally to a different computer if the driver installation routine does not help:
  
  Go to the computer to which the printer is connected. Note the name of the computer that you will get to the control panel > system > computer name. Now in the Panel, go to the printers. Find the printer in question, right-click, and then click Properties. Note the name of the share. Of course you must have already set up file sharing / print on all computers involved and share the printer.

  Now, go to the remote computer to which you want to add the printer. Control Panel > printers > add printer

  Click Add a local printer. Click on create a new port. The default value in the drop-down list box is Local Port. Don't change that. Click Next. A dialog box appears for you request that you enter a port name. Type in the \\FullComputername\SharedPrintername

  ex: \\mycomputer\HPDJ (that's why you wrote the names of computer and printer in the first step)

  Click Next. In the manufacturers list, select the correct printer manufacturer and the correct printer model in the Printers list. Under "do you want to use this printer as default printer select"Yes"(if you do!). and click Next. When asked to print a test page, select 'Yes', then finish.

  Configure file sharing / print:

  Troubleshoot network printer:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Share a printer:

  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

  I hope this helps.

• My Lexmark printer stopped working and the error message says "printer cannot communicate with the computer" (from "twisted into the USB pins?).

  When my printer stopped working because of error messages about "printer cannot communicate with the computer" (from "twisted into the USB pins?), I tried to change to 2nd USB port without success. I tried a new cable; that did not help.

  Then I uninstalled and reinstalled my Lexmark printer and changed the error message. Now, the printer does not work because "the USB device is not recognized."

  I tried to update the chips; Use 1 USB port; and using the old cable, all this without success. I checked the connections of the cable to the printer and the PC and turn on the printer and goes off; I'm out of ideas. Any other suggestions?

  Hi ChristineKrause,
   

  Here are some links that might help you:

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  Advanced troubleshooting tips for General USB for Windows XP problems

  Try the steps listed in the items mentioned above and see if that helps you solve the problem.

• The Lexmark 6500 series printer is compatible with Windows 8?

  Original title - devices

  The Lexmark 6500 series printer is compatible with Windows 8?

  Check it out here: http://www.microsoft.com/en-us/windows/compatibility/win8/CompatCenter/Home

  You will need to download the drivers for the Lexmark 8 victory if available

• Software installed but when I wanted to run it know my version of obsolete components DLLS are not compatible with this version of windows

  Software installed but when I wanted to run it know my version of obsolete components DLLS are not compatible with this version of windows

  I installed programs:

  Software individual professor teaches Super Set

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  Windows Vista Compatibility Center

  First thing to do is to check its Vista compatibility at the link above, and if not to see what patches/solutions are available from its manufacturer...

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  If this is not Vista compatible, read the info on the link above.
  It works for some programs, but not all.

  This applies to software programs, NOT hardware drivers.

  If it's Vista compatible > uninstall it > Re-download/save to your desktop > right click on setup.exe O run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• driver compatible for lexmark X 7350 all in one inkjet printer

  I need a compatible driver for my lexmark X 7350 all the under an inkjet printer, that I continue to download from does'nt lexmark works all the time, and sometimes the driver of my pc say not found.

  Hi David

  Mr. Vijay gave you a link.  Everything I did was right click on the Setup files and says to install in compatibility mode with XP.  All functions for my printer works fine.  I made the mistake of trying to update the printer file and it stop working.  I had to completely remove the printer driver on the computer so that I could then reload the software.  After that it worked again.  This hope and Mr. Vijays advice solves your problem.

  Steve

• How can Lexmark Z35, I get my printer to work with Windows 7?

  How can I get my printer to work with Windows 7?

  By looking at a site help on the lexmark, however this not is not supported under win7

• How can I reset the permission to receive downloaded programs? This authorization has changed and I don't know why. I am the owner and the only user of this computer.

  After a long work, I learned that I'm unable to download programs such as Adobe Flash and Microsoft Security Scan.  In fact, they do not enter the folder C:\USERS\CLAUDE\DOWNLOADS\---mais they may not be recognized by the operating system (SYS 7) because for some reason any access is denied.  I looked at the book and find that Claude file is locked.  I don't know how it happened.  I tried to see how to unlock but again without success.  Can you help me?

  Thank you

  Hi Claude1112,

  Looks like you can't access the download folder. I'll help you with this problem.

  1. have you made changes on the computer recently?

  2. what security software is installed on the computer?

  3. have logged as administrator?

  Method 1.

  Start the computer in safe mode and check if you can access the downloads folder.

  Advanced startup options (including safe mode): http://windows.microsoft.com/en-US/windows7/Advanced-startup-options-including-safe-mode

  If the problem does not occur in safe mode, then proceed to clean boot state.

  A clean boot to test if any element of service or third party application startup is causing this issue.

  How to troubleshoot a problem by performing a boot in Windows Vista or Windows 7:http://support.microsoft.com/kb/929135

  Note: Once you have finished troubleshooting, follow step 3 in the article to start on normal startup.

  Method 2.

  You can run the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

   

  Method 3.

  I would like to create a new user account and check if the problem still persists.

  Create a user account: http://windows.microsoft.com/en-IN/windows7/Create-a-user-account

  If the problem does not occur in the new user account, you can transfer the files from the damaged to the new user account by using the article user account "difficulty a user profile is corrupted.

  Difficulty a user profile is corrupted: http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  I hope this helps.

• Lexmark all-in-one x 74 - x 75 driver for vista?

  I fear I know the answer to this before asking.  There is no comparable driver Vista in the list published by lexmark.  Are there other options that don't involve buy me a new printer?  I can't believe I have to throw a printer perfectly well in the trash after just buying two ink cartridges very expensive for the thing.  Any help would be appreciated.

  Lexmark wrote their print drivers, not Microsoft.

  You guessed correctly.

  Unfortunately, it's the way business works.

  They make a cut point for writing new drivers for older printers and sell new printers instead.

  See you soon. Mick Murphy - Microsoft partner

• Help!... PRINTER LEXMARK ALL-IN-ONE X 5650 WILL NOT PRINT MORE THAN ONE PAGE... Help! (READY TO BURN THIS * @# % ^ THING)

  THIS IS MY PROBLEM... IM RUNNING WINDOWS 7, I AM ABLE TO CONNECT THE PRINTER TO THE COMPUTER WITHOUT PROBLEM. IF I TRY TO PRINT OR COPY ONLY ONE PAGE AT A TIME MOER THE PRINTER WILL RESTART AFTER THE FIRST PAGE HAS FINISHED PRINTING. I ALSO NOTICED THAT THE PRINTER DOESN'T IS NOT DISPLAY INK CORRECT LEVEL ON THE SCREEN OF THE PRINTER, (BLACK INK INK DIRECT 0% 0%) BUT IF I CHECK THE LEVEL THROUGH THE PREFERENCES OF COMPUTER PRINTER IT SHOWS THAT THE BLACK INK IS USED MORE OF THE COLOR INK. (BLACK INK INK 75%-100%). THE QULITY IMPRESSION IS POOR TO MUCH GREEN... ALSO WHEN I CANCEL THE JOB IN THE MIDDEL OF A PRINT JOB IT ALSO RESTARTS. I LAUNCHED A PRINT OF THE COMPUTER TEST PAGE AND IT PRINTS OUT THERE BUT WHEN ITS DONE WITH THE FIRST IMPRESSION AGIN RESTART ANOTHER. AND THE SAME FOR ALL "CARTRIDGES CLEAN CARTRIDGES-ALINGN" THE ONLY THING THAT WORKS WELL IS THE SCANNER... WHEN I PRINT A TEST PAGE TO THE PRINTER, I SEE A MESSAGE 'BAD CHIP HEATING' CAN THIS BE THE CAUSE OF ALL MY PROBLEMS, OTHERWISE THAT MEANS...

  HELP.............................. HELP.................................... HELP.......................

  ......................................... WHERES MY GAS AND A LIGHTER...

  Hi MTCAIME,

  ·         If it works well before? Do you remember any recent software and hardware changes made on your computer?

  1. I even suggest to run the troubleshooter under construction, link, you can refer to the same thing: Open the printer Troubleshooter: http://windows.microsoft.com/en-us/windows7/Open-the-Printer-troubleshooter

  2. make sure that the printer spooler is set to automatic, steps to set the service to automatic

  i. click on start and type services.msc in the search box

  II. search for the Printer Spooler service

  III. right-click on the service

  IV. If the service is stopped and then starts the service

  v. Select Properties

  VI. and in startup type, select automatic

  3 uninstall the driver and related software and reinstall it back. To uninstall, see the link below: Uninstall or change a program: http://windows.microsoft.com/en-US/windows7/Uninstall-or-change-a-program

  Link for the drivers from the Lexmark Web site: http://support.lexmark.com/index?locale=en&productCode=LEXMARK_X5650&userlocale=EN_US&segment=DOWNLOAD&os=WINDOWS_7&page=downloadsList&oslocale=en_US#4

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Lexmark Pro 901 printer loses connectivity with the computer

  I have a Lexmark Pinnacle Pro 901 printer I bought at the office supply store there are several moonths. I hung it, and it worked for a short period, then I got a screen prompt saying that there is no connection between the printer and the computer. I was on the phone and even authorized Lexmark technicians to have remote access to the computer 2 times. I've been on the phone with them about 10 times and had even them I would send printer back and they sent me new printer. I even had a friend local tech come and he has reinstalled printer drivers, each time, that it's the same thing, printer will work for one or two jobs and then stops printing. I can still make copies and yesterday I scanned and sent by e-mail a document, the Green WIFI light is on. I'm so frustrated that I just want to get rid of this printer. Help!

  Hi BrianParkerWX,

  You did changes to the computer before the show?

  I suggest you try the steps from the following link:

  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
  http://support.Lexmark.com/index?locale=en&page=product&UserLocale=en&ProductCode=LEXMARK_PINNACLE_PRO901&focusedTab=downloads#1

  Additional information:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• LEXMARK ALL-IN-ONE X 1150 PRINTER DOES NOT NOT AFTER UPGRADING FROM VISTA TO 7.

  I TRIED DRIVER DOWNLOAD FROM LEXMARK WEBSITE BUT WITHOUT SUCCESS.IS THERE A SOLUTION OUT THERE?

  Thank you Dominic.I have taken the bull by the horns and contacted Lexmark (to the Philippines Croiriez_ you) and I'm now up and running. They were excellent.

• The Menu bar and status bar disappeared, but the worst of all the tabs is at the top of my computer. It's very annoying! How can I uninstall Firefox 4 and return to the old?

  Please tell me how I can go back to the old format

  If you don't like the new look of Firefox 4, then you can change some settings to restore the appearance of Firefox 3.
  
  You can right click on the orange Firefox button to open the menu of the toolbar or use (F10) view > toolbars.

  • Click on the entry in the Menu bar to make the menus visible bar.
  • Click "Tabs at the top" to remove the check mark and place the tab to its original position bar just above the browser window.

  You can use this extension to retrieve the status bar:

  • Evar-4-status: https://addons.mozilla.org/en-US/firefox/addon/status-4-evar/
  • http://www.computertechtips.NET/64/make-Firefox-4-look-like-FF-3-6/

• Hi did anyone know what CPU i7 is compatible with this motherboard?

  Dell Xps L502x

  aware of the CPU: i5 - 2410 m

  card mother Version: A00

  card mother name: 0YR8NN

  map parent serial number: BGS60Q1. CN4864315E1503.

  who better for the games the 2670QM or a 2640 m i7?

• I don't know why I get the error "function object is not defined" with this script.

  Hello

  I have a script which adds a unique model in the render queue and applying a Render parameter model and model output for adding module make element of queue.  For some reason, I am getting an error on the first line which reads:

  app.project.renderQueue.items (1), .applyTemplate ('MY SETTINGS');

  I have attached the image of here error dialog:

  

  Here is a part of the script.

          var currentProjectItem;
          var globalCompItemID;
          var renderCompItemID;
  
          for (var i=1;  i <= app.project.numItems; i++)
          {
              currentProjectItem = app.project.item(i);
              if (currentProjectItem.name == "globals")
              {
                  globalCompItemID = i;
              } else if (currentProjectItem.name == "!_FINAL RENDER") {
                  renderCompItemID = i;
              }
          }
  
          //add the necessary preview render jobs
          app.project.renderQueue.items.add(app.project.item(renderCompItemID));
          app.project.renderQueue.items(1).applyTemplate("MY SETTINGS");               <---THIS IS WHERE AE ERRORS
          app.project.renderQueue.items(1).outputModules[1].applyTemplate("MY SETTINGS");
          app.project.renderQueue.items.add(app.project.item(renderCompItemID));
          app.project.renderQueue.items(2).applyTemplate("MY SETTINGS");
          app.project.renderQueue.items(2).outputModules[1].applyTemplate("MY SETTINGS");
          app.project.renderQueue.items.add(app.project.item(renderCompItemID));
          app.project.renderQueue.items(3).applyTemplate("MY SETTINGS");
          app.project.renderQueue.items(3).outputModules[1].applyTemplate("MY SETTINGS");
  
   
  

  The model I want to add is added to the render queue, it simply refuses to invoke the method applyTemplate() on the most recently added make queue item.

  Any ideas why I get this error?

  Thank you!

  I think that from the line where the error occurred, you must use renderQueue.item () instead of renderQueue.items () (except when you add something to the rendering queue).

  Dan