LifeCam PIN required

Similar Questions

• Microsoft Lifecam Cinema works well with windows live messenger.

  I just bought a Microsoft Lifecam Cinema, connected with my PC and installed the software 3.6. What I noticed that the quality fo the vedio going well under the lifecam software or to preview audio/vedio setting of the windows live messenger. However, the vedio quality is pretty poor, when I compose a vedio with other people using windows live messenger.

  I don't know if this is related to the operating systems or not. My operating system is XP Professional, the other part is windows 7. the version of my windows live messenger is current.

  Any advice?

  Hi IanZ11,
   
  The LifeCam software requires a card video and monitor that can run a resolution of at least 800 x 600 high color. Set the resolution of Windows display on 800 x 600 high color and then test the software.
   

  Try the steps listed in the article below and check if that helps you.

  Don't troubleshoot bad or no video or problems to start the LifeCam software     

• LifeCam Cinema HD has limited resolution in Vista

  I'm running Vista/64 with all updates and SPs.  Just bought a MS LifeCam Cinema HD for use with this computer, and the only resolution I can get is 160 x 120, none others appear on the list of the menu drop down.  I have downloaded the software twice, have done everything that this issue, but on this computer that low-resolution is all I can get recommended to others.

  HOWEVER, I uninstalled the software and the LifeCam then works with Skype with a much better resolution, but certainly nothing of such quality HD.  As soon as I re - download and install the LifeCam, the resolution of Skype software goes to pot.

  I tried to install this WebCam on a laptop running Win7 and all resolutions are availaable on the menu drop down, I can make videos in HD and HD even works on Skype.

  Is there a fix or a workaround for this?  I like the WebCam, especially autofocus, but at 160 x 120, the autofocus function is academic.

  Hi Electrojim,

  -What troubleshooting steps have done up to now?

  I suggest you to plug the LifeCam Cinema HD into another USB port and check if it makes a difference.

  The LifeCam software requires a card video and monitor that can run a resolution of at least 800 x 600 high color. Set the resolution of Windows display on 800 x 600 high color and then test the software.

  Try the steps listed in the article below and check if that helps you.

  Don't troubleshoot bad or no video or problems to start the LifeCam software

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• Request for Pin wireless connecting to a linksys router

  I want to heck the feature in windows vista that asking to enter a PIN instead of simply asking for my shared key of wireless wpa. Can someone tell me please how to disable this feature in windows vista.

  The possibility of using a PIN instead of a password for wireless is on the router, not the computer . Go to the Linksys configuration utility and disable the PIN requirement wireless has from there. This is general information about implementing a secure wireless network, which includes how to enter the configuration of the Linksys utility.

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Excellent guide for setting up of a wireless network, with images -http://www.microsoft.com/windowsxp/using/networking/setup/wireless.mspx

  MS - MVP - Elephant Boy computers - don't panic!

• Bad Update

  I guess that this week has been a bad time to spend at a vista 64-bit operating system.  I installed the operating system and drivers last night. After that I installed and got my departure from security software, I put the computer to update and install it. Now my computer (Dell Studio 16) will not start. I can't with safe mode, and it won't let me not reinstall windows again. When you try to start in safe mode I get a blue screen, I can't read because it's so fast and then a page that says windows could not load. When I tried to reinstall the computer to read the cd with the os cd and charge of the case, but then goes black. No action after that. So, what can I do? Called Dell and they want me to buy a $300 software warranty before they will help.

  Hi Acts29jason,
   
  I would like to give you some information about the Blue error screen you get:
   
  1. the file system is damaged and cannot be mounted.
   
  2. you use a standard 40-wire connector cable to connect the UDMA drive to the controller instead of the 80 cable son and 40 pins required.

  3. the basic input/output system (BIOS) settings are configured to force the acceleration of UDMA modes.
   
  4. it may also be a problem with the hard drive.
   
  Updates are not the reason for this problem to occur. If this is not the case now, it reportedly took place after a year or two because of the material. If it was'nt a problem with the hardware we could have booted from the disc of Windows Vista and we could have then a system restore or a disk check. Since we are not able to boot from the Windows Vista disc, we can say that there is a problem with the material most likely the hard drive.
   
  I have an article that addresses this issue, but this article is related to Windows XP, but I think that it would apply for Windows Vista. As it has troubleshooting steps as check disk that we would have tried if we start from the Windows Vista disc.
   
  http://support.Microsoft.com/kb/555302
   
  I hope this information is useful.
   
  Please let us know if you need further assistance.
   
  Concerning
  Rehman - Microsoft Support

• Add HD 4850 video card in HP Envy 700-215xt

  I want to add a Radeon HD 4850 HD-485 X-ZNFC video card in HP Envy 700-215xt (model: F9A62AV) whose video card (Intel HD Graphics, DVI - D graph) is too poor to run Samsung monitor (24in).  HD 4850 videocard needs connector 6 pin power, but I can't find the power connector or cable. What should I do?

  The PSU minimum power, with a PCIe power connector 6-pin requirement is 450 watts.

  Your PC has a 300 Watt POWER supply. Is not enough power for the XFX video card.

  You must also upgrade the PSU to intensify your graphics card for a XFX HD4850 video card.

  If you are unable to get a graphical output on the 24-inch display, then it is likely to be a problem with the display or the cable.  You may not be the entry configured to automatically recognize a video signal. You can test that by connecting the original display. If you get a video output to the original display there is nothing wrong with the motherboard or the CPU. Intel HD4600 graphics are provided by the CPU, not a graphics card.

• P6744: model of pci P6744D version

  I use P6744D from HP and my motherboard model:

  MS-7613 (Iona-GL8E)

  Here my questions:

  (1) what is the PCI Express version? Is 2.0 or 3.0?

  (2) I wanted to upgrade my graphics card for this model R939 8GD5 is possible?

  Thank you

  This certainly isn't PCIe 3.0, but a card PCIe 3.0 will work in your motherboard. You will certainly need to upgrade at least 500W POWER supply because it is a 6 + 8 PCIe power connector pins required.  My preference is at least a power supply of 700 w for a game system. The original power supply in your PC doesn't have the PCIe power connector. Your PC case will accommodate an ATX PSU.

  Information on your PC

  http://support.HP.com/SG-en/product/HP-Pavilion-P6000-desktop-PC-series/5035348/model/5082310/document/c02758913/

  Sheet on the ASUS video card you asked

  https://www.ASUS.com/graphics-cards/R9390DC28GD5/specifications/

  Measure the inside of the case, as described in the explanation in 2012 to ensure that the 11.3 "x 5.8" x 1.6 "inch video card will fit."

  The installed processor is a version of 2009 and the motherboard has no usb 3.0.

  There was a discussion related to your request for 2012.

  http://h30434.www3.HP.com/T5/desktop-hardware/upgrading-graphics-card-on-HP-Pavilion-p6520f/TD-p/1296863

• Cannot start Windows xp do not. I experienced the process of trying to start my computer using F8, but none works.

  I now have a blue screen display:

  UNMOUNTABLE_BOOT_VOLUME

  STOP: 0x000000ED (0x83304c08, OxC0000006, 0x00000000, 0x00000000)

  I have no idea what this means, I would so appreciate any help and advice.

  Thank you

  Jack's mother. Thankfully, were allowed to use compute Jack then she cluelessly trying to sort his own...

  Hi JackLewington,
   
   
  This problem can be caused if:
   
  1. the file system is damaged and cannot be mounted.
  2. you use a standard 40-wire connector cable to connect the UDMA drive to the controller instead of the 80 cable son and 40 pins required.
  3. the basic input/output system (BIOS) settings are configured to force the acceleration of UDMA modes.
   
  Here is an article that addresses this issue. Follow the suggestion given in the article below to resolve this issue:
  Unmountable Boot Volume

• __unmountable_boot_volume STOP: 0x000000ED

  Original title: __unmountable_boot_volume

  STOP: 0X000000ED (0X82F3D590, 0X000009C, 0X00000000, 0X00000000)

  • what it means?
  • How can I restart the computer with F8 safe mode doesn't seem to work

  Hello

  This problem may occur if one of the following conditions is met:
  1. your computer uses a UDMA Ultra Direct Memory Access () hard disk controller, and the following conditions are met:
  2. you use a standard 40-wire connector cable to connect the UDMA drive to the controller instead of the 80 cable son and 40 pins required.
  3. the basic input/output system (BIOS) settings are configured to force the acceleration of UDMA modes.
  4. the file system is damaged and cannot be mounted.

  Follow the steps described in the article below and check if that helps resolve the issue.

  When you restart your computer or upgrade to Windows XP, you receive the error message "STOP 0x000000ED UNMOUNTABLE_BOOT_VOLUME".
  http://support.Microsoft.com/kb/297185

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to install the graphics card Nvidia Quadro 4000 in Dell R710

  Hi all

  I read a lot about the installation of the Nvidia Quadro PCIe x 16 card in a Dell R710.  I know what parts I need to order (Dell GP347 PCI-e left Riser), but I don't know how to install the power cable 6 pin required by the Nvidia card.  Where would connect it to the motherboard Dell R710?  Is there a place to connect?  If not, is there some type of power provides I can hang the 6-pin power Cable from Nvidia and power the server?  Any help would be appreciated.

  It's a bit old now, but thought I would answer that I had this work and very happy with the performance!

  In addition to editing card, that I needed, there is NO way to provide the power that the card must provide without a power SUPPLY.  There is a really small box listed on Newegg called "ePOWER EP - 450CD 450W ATX12V/EPS12V modular juice dedicated to the area of graphics card and CPU of power".  Buy and run the GPU power cable to an empty PCI slot at the back of the Dell server.

  I also bought some video cards NVidia Quadro 4000 2 GB GDDR5 PCIe for each of my 5.5 ESXi servers. Also, I left my active integrated video graphics card and it is always primary for my hypervisor.

  Download and install the NVidia ESXi drivers on their site and follow the directions to install.  Reset.

  I use sVGA with my Horizon offices and downloaded a trial version of Sketch-Up to test the 3D.  They have a community of users who post 3D renderings and you can download it directly from the Sketch-up program.  Cruise around and check the performance.

  As a side note, I noticed IE worked worse way by using the GPU when browsing the internet.  Go to settings, advanced in Internet Explorer and has the option at the top of the page "use rendering software instead of GPU".  This change makes IE works as expected.

• Cannot install lifecam hd-3000 on my old toshiba laptop windows xp, I have no configuration required

  my computer - toshiba 2004 (old) Windows xp cannot install lifecam hd-3000

  Hello

  How you are trying to install LifeCcam on your computer?

  Make sure that the computer you are using meets or exceeds the minimum video, processor and memory to install and run LifeCam.

  Open the DirectX Diagnostic tool. To do this, follow these steps.

  (a) click Start, click run, type dxdiag in the Open box, and then click OK.

  b) on the System tab, note the processor and memory values listed under System Information.

  (c) on the view tab, note the value of approx. total memory is listed under the device. Most LifeCams require at least 2 MB of video memory.

  (d) click exit to exit the DirectX Diagnostic tool.

  Compare the values that you noted in the minimum system requirements that are required for LifeCam. You can find the system requirements for each LifeCam on the Microsoft Hardware Web site. Click on the product of LifeCam you have installed, and then click the Details tab to review the system requirements.

  To compare the system requirements for your LifeCam product, please visit the following Microsoft hardware Web site:

  http://www.Microsoft.com/hardware/digitalcommunication/ProductList.aspx?type=LifeCam

  Note: If the computer does not meet the minimum system requirements, contact the computer manufacturer for more information about how to obtain the updates and upgrades.

  For further information, you can consult these articles.

  Troubleshoot installation of Intellipoint and IntelliType LifeCam software

   

  Troubleshoot failures to find the new LifeCam hardware

   

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756/

• HP Officejet Pro X567dw: Required PIN after wake up

  Hi all

  I have print via WiFi. When I run the printer I can print now worries.

  When I connect my laptop to the wireless network when the printer is hooked up with, the printer asks me to enter a PIN and I can not print documents.

  When I restart the printer documents are printed.

  How can I stop the requirement for the PIN?

  Thanks, Martin

  You have Direct wireless enabled in the printer? If so, disable it.

• Error message "Required line was not found in the INF" LifeCam Cinema 3.0 on Windows Vista Edition installation Home Premium

  The LifeCam Cinema hardware installation error
  
  Tried to install Lifecam Cinema 3.0 but keep on receiving an error message "Required line was not found in the INF" - OS is Vista Home premium edition

  LifeCam installed on my laptop XP

  Hi seuss460,

  LifeCam software version 3.2 is available; Make sure you install the correct software for your hardware.

  You can download software LifeCam here

  Step 1: You can follow the steps mentioned in the article below

  Troubleshoot installation of Intellipoint and IntelliType LifeCam software

  http://support.Microsoft.com/kb/953691

  Step 2: See also the steps mentioned in the article below

  Troubleshoot failures to find the new LifeCam hardware

  http://support.Microsoft.com/kb/929087

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pin code of blackBerry Z10 Sim Card required daily

  My required daily BBZ10 my sim card pin code, what should I do to prevent this?

  I'm not reachable when I'm on call to work during the night because of this.

  Thanks a lot for some feedback

  Gino

  Hi Ginodesoomer,

  Welcome to the support community!

  Looks like you have security enabled on your SIM card. You can disable this option to avoid to be invited for the PIN. Please see this article for more information. "" Enter PIN"is displayed when the BlackBerry smartphone is locked" KB18647

  You can disable this on your BlackBerry Z10 smartphone in settings > privacy and security > SIM card > SIM Lock card PIN.

  Please let me know if that helps.

• TMS 14.3 - PIN is not required for endpoints imersive

  Hi people,

  I am facing a strange with TMS 14.3 + driver problem XC2.2 + TP Server 3.1. This is what happens:

  Schedule us a conference in TMS conductor like MCU, click an alias that points to the server TP conference bridge. The Conference has a self-generated PIN 6-digit. We use the type of conference "No connection", where all participants must manually dial into the Conference and insert the PIN.

  Well, when at the request of conference starts, all participants can join the Conference successfully using ID number and then insert the PIN code. However, for the endpoints imersive telepresence (CTS 3000), when the user dials the ID number, it is connected to the conference without having to insert the PIN, TP Server don't ask the user to insert the PIN, endpoint imersive is automatically connected to the Conference after dialing the digital ID.

  I have no idea why this is happening, and I confirm that this happens only for CTS 3000, the same problem does not occur for 500 CTS, for example, which is registered to the same CUCM with the same version of firmware. Extra points that I realized:

  • This problem seems to be related to MSDS. Because, if I create an alias Chief conductor associated with a model of the Conference which has applied the PIN, so the problem does not occur. All the endpoints are required to insert the PIN, 3,000 CTS. But when planning through TMS, the problem occurs.
  • The problem happen if the CTS 3000 is selected in the list of participants when planning or not. In addition, no matter if the CTS 3000 is the first, second or last member to join the Conference, the problem always happen in any time.
  • No matter if I use Conference alias set of a driver to be "imersive" in configuration of TMS or alias of the common, the problem still occurs.
  • In the web page of the server TP, I can see the Conference he indicated "PIN protected" information

  Everyone here knows about a problem like this before?

  I'd appreciate any suggestions really.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

  CDETS ID is: CSCum29993.

  VR

  Patrick