Limit the bandwidth on a Cisco router (possible 1800 series)

Similar Questions

• Limit the bandwidth for WNR614 router n300 wireless devices

  Hello

  I use the WiFi WNR614 N300 router. Is it possible to limit the bandwidth for devices that are connected on it.

  I thank you,

  Vignesh C

  Hi @vic2408

  Welcome to the community!

  To answer your question, there is no way to limit the bandwidth on each of the devices.
  You may need to use a 3rd party software to do this.

• How can I limit the bandwidth for endpoint on the router from 1921 to mitigate impacts traffic bittorrent reviews?

  We have implemented an independent network for our wireless comments. It's an ADSL modem, enter a 1921 Cisco. I setup NAT and DHCP on the router and it is only accessible through the wireless connection. We have a connection 50Mbps and about 250 devices connected to it. Some of them use bittorrent and other file-sharing software to quickly eat bandwidth.

  Since the torrent software is adjustable to any port and cannot be blocked like this, I was wondering if there is a way to limit the bandwidth available to each device connection mitigate this.

  I put this in the Group WAN because it seemed appropriate as it performs the external connection. I know that the argument could be made for LAN, because it connects only within the corporate building and not to one of our service centers.

  Any help would be appreciated.

  Hi John,.

  I don't see anything wrong to apply a basic qos strategy, rank traffic using nbar to match with the bittorrent Protocol and other similar protocols. And then just Butterfly traffic down using a map policy.

  HTH

  Mike

• Can I limit the bandwidth of comments for the R7000 Netgear network?

  Hello dear community,

  is there a way to limit bandwidth (not for games) for the network of comments?

  Or you can limit the bandwidth with this router for specific mac addresses?

  Is it possible to display consumption of direct download (real time) for a specific device, which is connected to the R7000?

  Thanks in advance.

  Same questions answered in this thread, monitor the use of data by the device X 6 R8000.

• How to limit the bandwidth in the VPN Tunnels in RV082?

  Hello

  It is possible to limit the bandwidth of the IPSEC VPN Tunnels or the traffic that goes through the tunnels?

  Use IP addresses or port numbers the same way and clients when limiting bandwidth to clients in the local network?

  Thank you very much

  Oliver

  There is a way to solve internal IP addresses, protocols or ports and specify the bandwidth

  I send you the links to access information on how to set it up.

  http://www6.nohold.NET/Cisco2/GetArticle.aspx?docid=3c09b393e3744ffd98330fd0031a4aa2_4228.XML&PID=80&converted=0

• Limit the bandwidth connection Internet comments

  Hello world

  I'm working on the network with 3 4404 WLC s on the internal network, and now let's add another controller to the DMZ to make an anchor for a guest WLAN controller. I have a request to limit the internet bandwidth for the network invited to 25% of total bandwidth or less. The firewall is a Pix 515 7.0 (2) running.

  Anyone has any ideas on how I can limit the bandwidth on a particular WLAN. I was thinking about QOS on the WIFI, but there must be a way easier or more.

  Thank you all...

  It works very well for us. I used several tools to check the bandwidth is limited and he seems.

• ESXI 4 - can I limit the bandwidth used by each guset?

  Hi all

  I was wondering if I can limit the amount of bandwidth used by each of them to the virtual machine?

  I have two VM (in the future there will be more) with server 2003 installed on them.

  Map of network Wan ESXI has 40 MB of connection, and I want a virtual machine to have a limit of 15 MB and the other VM to have a 25 MB limit.

  Can it be done?

  With our thanks,

  Itamar

  No, you cannot limit the bandwidth with this granularity, bun, you can set the average bandwidth for all virtual machines connected to the network of the virtual machine port group.

  In the case of 2 virtual machines, I guess you can simply create 2 groups of network ports VM differet with average 15 to 25 Mbit bandwidth, but it would ' be really easy to maintain if number of VM will grow.

  ---

  MCSA, MCTS, VCP, VMware vExpert 2009

  http://blog.vadmin.ru

• How to limit the bandwidth for each different devices connected to my router

  Hello

  Thanks in advance!

  Can you help me to limit bandwidth on perticular devices, I use NETGEAR (WNR1000v2 - N150 wireless router) and the version of the firmware of the V1.1.2.58, like almost 4 devices are connected to this router, I want to limit the speed of bandwidth to each device.

  I have not found the Qos in my Netgear.

  It might help if you provided in details with screenshots.

  Thank you

  Samira

  Not possible with this model of router

• Limit the bandwidth in the tunnel VPN on Cisco ASA

  Hello

  I have a site VPN tunnel to create with the local desktop client. I fear that the traffic in the tunnel in impacting the Internet bandwidth for the entire office. Is it possible to limit bandwidth on the speed VPN tunnel. I have attached a configuration that shows the configuration of the ASA at the local office.

  Any help would be much appreciate. I watched QoS mapping but it's hard to make sense.

  Thank you very much

  Kind regards

  Michael.

  The ASA supported QoS features are:
  Police, LLQ and Traffic Shaping

  To avoid the individual flows hogging the bandwidth of the network, you can limit the maximum bandwidth used by flow (with the police)
  The police is a way of ensuring that no traffic exceeds the rate (in bits per second) that you configure,
  so make that person not traffic or the class can return to any of the resource.
  When traffic is higher than the maximum rate, the ASA removes the excess traffic. Policy defines also the largest single burst of allowed traffic.

  Example of font options:
  class policing_map_name hostname(config-pmap) #.
  Police hostname(config-pmap-c) # {exit | entry} to compliance rates [conform burst]
  [action in line [drop | send]] [action exceed [drop | send]]

  That is to say

  HostName (config) # class - police-class card
  HostName(config-CMAP) # match any
  HostName(config-CMAP) # QoS_policy policy-map
  class police_class hostname(config-pmap) #.
  HostName(config-pmap-c) # exit police 56000 10500

  The configuration depends on the "this" base that you want to limit the connection.

  Federico.

• Apple has added a feature to limit the bandwidth on the networks of comments yet?

  I've read many threads saying that the bandwidth of the guest network could not limited to Airport utility, but most of them have at least 2 years. Apple still feature added to its range of airport?

  It's not even a firmware update... and without a completely new firmware, there is no possibility of QoS. I think you expect that Apple will never offer more. They reduce the functionality does not improve it... Look for example at El Capo disk utility.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• I'd like to find the password for my Cisco router

  I can't connect to my network wirelessly on my ereader, because I don't know what is the password when asked.

  Read the manual for the device (Cisco router) should tell you what the password by default is to manage the router (if this does not work... it should tell you how to configure the default router, so you can use the default password to reconfigure) so you can go and change the password to access wireless to something You know.

• Need some advice about the VPN between local Cisco router and remote Watchguard

  Hi all

  I am configuring a Cisco 887 to VPN router to a device of watchguard at the remote site.

  From what I understand, the VPN tunnel is in PLACE. I can ping to the remote server on the 192.168.110.0 of the network, but whenever I try to navigate to it on the local server, it wouldn't work.

  I ping the remote server via the IP address on the local server, but not on the Cisco router. Is - will this work as expected?

  --------------------------------------------------------------------------------------

  R5Router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  110.142.127.237 122.3.112.10 QM_IDLE 2045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  --------------------------------------------------------------------------------------

  R5Router #sh encryption session

  Current state of the session crypto

  Interface: Virtual-Access2

  The session state: down

  Peer: 122.3.112.10 port 500

  FLOW IPSEC: allowed ip 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 1 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 6 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip host 122.3.112.10 192.168.0.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Interface: Dialer0

  The session state: UP-ACTIVE

  Peer: 122.3.112.10 port 500

  IKEv1 SA: local 110.142.127.237/500 remote 122.3.112.10/500 Active

  FLOW IPSEC: allowed ip 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 2, origin: card crypto

  FLOW IPSEC: allowed 1 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed 6 192.168.0.0/255.255.255.0 192.168.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip host 122.3.112.10 192.168.0.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Crypto ACL 102, should really include only 1 line, that is to say:

  10 permit ip 192.168.0.0 0.0.0.255 192.168.110.0 0.0.0.255

  and you should have the image mirror on the remote end ACL line too.

  PLS, remove the remaining lines on 102 ACL ACL.

  I guess that the ACL 101 is NAT exemption, if it is pls include "deny ip 192.168.0.0 0.0.0.255 192.168.110.0 0.0.0.255" on top of your current line "license".

  Clear the tunnels as well as the NAT translation table after the changes described above.

• Limit the bandwidth Time Capsule

  I am about to install a new Capsule 3 TB but am simultaneously looking for a solution of throttling split a WIFI network guests & owner. There are only 70 GB p/month available (satellite 2way) and currently you can empty just this pipe in a few weeks, if lucky (streaming, etc...).

  I know that the Time Capsule can accommodate a network comments without restriction of time but will not be enough and is too restrictive.

  Any suggestion would be appreciated.

  Unfortunately, Apple routers have not all parameters that would allow the owner of the control bandwidth allocation... (which is known as QoS or Quality of Service) in some way.

  If your needs call for this type of service, then your only real option would be to add a router with the features you need... and then put in place the time Capsule to run in Bridge Mode.

  Time Capsule provide a 'network of comments' feature when it is configured in Bridge Mode, then you may want to look for a router that would deal with this type of function.

• Wireless connection disappeared after pressing the button system Orange Cisco router WRT54G

  Trying to connect to a printer Dell wirless to the router and has failed, after many tests to get the computer to recognize the printer as a wireless device.  Recommended by Dell to refresh the router and I pressed the button in the above subject line.

  Now, none of my computers display the connection wireless as available. I have reset the time many cable modem and the router and him that restarted the computer and they still will not recognize the wireless connection.

  Also, I tried to use the default IP 192.168.1.1 to review my settings for the router (running a laptop directly via the cable modem), but the address keeps timing.

  What is someone out there knows what can happen to connect wireless to disappear?  Any help is greatly appreciated.  Don

  Your wireless network is gone because you press the WPS button on the front.  Never do this because you don't have the hardware to support it.  Change the SSID and password.

  Press and hold the reset on the back for 30 seconds and then release.  Wait 10 seconds and cycle power to the router.  To connect to a computer wired to the router at 192.168.1.1 only empty password, username "admin".   Now configure the router manually.