Linear encoder and configure logging

Similar Questions

• Why the my linear encoder is only tend to read negative?

  I have a linear encoder, that I am using with one NOR cDAQ 9184 & 9401.  I basically used the example of linear encoder, I found here on the website of OR, however, when I run the program I find that measuring only in one direction is the precise movement of reading.  By this I mean when my encoder moves upward (actually my camera moves down and the encoder is fixed) I can move properly, but when moving in the opposite direction I'm away.  I'm not a linear sum, very different each time.  Sometimes when the movement he began first almost looks resets the unit to its original position (0 "), but I am helpless as to why.  Does anyone have an idea on how to remedy this situation?

  I'm pretty confident I have things wired properly while this same configuration/encoder reads correctly in MAX, see the second screenshot.

  Well it seems that the question was much easier than I thought.  Of course, I'm a newbie to this, but I think that most of the confusion was due to the lack of detailed information.  None of the documents of OR really explained me the option counts two impulses, more the X 4 and documentation of the mentioned readhead times count four.  However, after receiving no not any solid solution, I started completely over and tried all the options I had along the way.  In short, my solution was to simply what I posted in my screenshot, but simply change the X 4 option for counting of pulses two option.

• connection of users and configuration of MAX

  I searched the site for 3 days and finally found a post titled; "IAK login user and configuration MAX" on 04/21/2009 who has asked pretty much the same problem, I'm going to. I wonder if there is something new on this subject because I need a solution.

  I installed an application and the NI FP driver suite see 6.0.11. I run NI MAX and open my. File IAK, which is located in the folder/common directory as well as the executable file of my application. At the beginning I used to hit the 'Save' selection but have found since that it makes no difference, so now, I'm not hitting 'Save', but just close MAX. This process is to record the location of my. IAK file somewhere, because after that my application runs and communicates very well with my e/s.

  The problem comes when I have the new station operators connect to the computer that controls the operation of my test. the application that auto starts because it is in the startup folder "All Users" cannot communicate with inputs and outputs.

  MAXIMUM running and opening the. IAK file under each new user login then immediately closing MAX solves the problem and all is well, and this process must occur the first time that a new user connects to the computer. The post mentioned above indicates that it is a normal behavior.

  The problem is that some of my operators do well to find the power button and turn on all the morning. The application is no "Exit", "Task Manager" should be used to stop it. Login information is stored on a post-it in their portfolio, and ask them to open MAX and save the configuration is just too much for them to do - be unfamiliar with the operation at first.

  Can someone explain to me how to fix this or refer me to a validated solution?

  Thank you

  OK - here it is:

  It works for me under Windows 7 with FP1000 e/s on a serial Comm. port other configurations may or may be not the same in these respects.

  While logged in as a privileged user configure you application to work and communicate with the e/s using an IAK file. Create the IAK via NI MAX.

  Is the key to register of interest here: [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer\Recent File List]

  The string value is: "File1"="C:\ApplicationPath\IOConfigurationFile.IAK."

  Start the REGEDT32 Registry Editor. EXE and navigate to the key just below SOFTWARE that tells of National Instruments.

  Select the key, and then right-click on it. Select EXPORT, select a path and name of the output file.

  There will be many other entries, but this recent file one is the only one that may be necessary.

  You will end up with one. REG file with the specified name that contains the following elements:

  Windows Registry Editor Version 5.00

  [HKEY_CURRENT_USER\Software\National tools]

  [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer]

  [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer\Recent File List]
  'File1"="C:\\ApplicationPath\\IOConfigurationFile.iak '.

  Create a BAT file under the name of your choice. Configure.BAT for example.

  This BAT file will reside in the directory of your application with your Important file and it will contain 1 line.

  This:

  REG IMPORT "C:\ApplicationPath\ConfigurationRegistryExportFile.REG" > rejconfig.log

  Place a shortcut to it. BAT file in the 'All Users' Start menu.

  Any user who connects will receive this update of the registry which will allow the driver to IO to know how to communicate with your IO.

  Replace your appropriate to the ApplicationPath, IOConfigurationFile, ConfigurationRegistryExportFile, rejconfig.log file names. The log file will be written only for in the case of an error.

  Good luck

  Dfhotz

• "DAQmx Configure Logging" found in Labview 2009

  Dear Sir or Madam

  I have the version of Labview 9.0f3 instored. Measurement & Automation Explorer version 4.60f1 instored.

  Must I update anything to run the attached VI?

  Problem:

  As mentioned in the file like this http://zone.ni.com/devzone/cda/tut/p/id/9574

  "NOR-DAQmx 9.0 installs a new DAQmx Configure Logging VI VI". However, I can't find this VI in my control panel and the icon appears as a question mark.

  

  There are two ways to check your version of DAQmx:

  (1) measurement and automation explore:

  

  (2) using Add Remove programs

             

  My guess is that you use DAQmx 8.9.5 and need to upgrade to 9.0 or later.

  Best regards

• How constantly sample meter signal for quadrature linear encoder

  Hi all

  Trying to permanently change value of Schneeberger linear encoder quadrature at certain frequency as 10 Hz of the sample and the output to the text file. Everything I choose in the external clock that I can't run the DAQ assistant. No one knows how to fix? I don't know what kind of clock can be used.

  I have read a few replies that ppl would connect to an another sample clock in parallel with the meter channel. But I don't know what is the principle of operation of this method.

  I spent already as 10hours on it. Could someone tell me that some information?

  Looking forwad to your help! Thank you very much!

  Best regards

  George

  Hi George,.

  You'll want to use the DAQmx API rather than the DAQ Assistant.

  The task of the encoder itself would look like this.  You need not use the trigger options.

  The problem is that you will need to generate a clock from another source that the card is unable to generate examples of clock counter directly.  The simplest is probably to use the second counter.  Here is an example showing how to use a meter to output as a sample clock (although the example shows the analog inputs, simply replace the task of analog input with the task of the encoder shown in the previous example, I linked).

  So, you would use a counter (say ctr0) for the task of the encoder, and then the other (ctr1) meter for the generation of sample clock.  You must specify your task of encoder using the InternalOutput of ctr1 as the sample clock (if the internal counter output appear in the drop-down menu, click with the right button on the terminal and select the e/s name filtering > include Advanced terminals).  Start the encoder task before the output task (although given that both are running continuous it doesn't really matter that much).

  In addition, 10 Hz is not too fast.  If the exact date is not as important and the above seems a little overwhelming, it might be easier for you to just run a loop of 100ms clocked by the software from example like this.  Note that the exact time loop pourrait will vary from cycle to cycle, so this method is not very good if you use sampled data to perform calculations of rates.

  Best regards

• When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.

  original title: log question.

  When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.  How can I fix?

  Hi KERRYYX,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?
  4. What is the full error message that you receive?
  5. Are you able to restart and shut down the computer?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  You cannot log off, restart or shut down your Windows XP-based computer

  http://support.Microsoft.com/kb/831431

• Y at - it a fix for leak of VRAM in Windows Desktop? (Windows media Encoder and photo IE10 Viewer are the root of the problem)

  It seems that Windows media Encoder and photo IE10 Viewer are the root of the problem, and it is about the whole MS Platform in desktop for what anyone associated media.  As easy as it is to use another browser or image viewer I find I like the windows photo viewer ability to preview multiple images and IE10 and 11 are more now then fix everything that exists.

  The issue is having to restart or log out and back in just pass leak VRAM that can go up to 1400 MB and count. What said GPU - Z and ESTR.  The memory of the system seems to be in check most of the time.  Get off my GPU memory Windows.

  I mean leak even with the left running only windows desktop and essential tasks to keep it that way.  I have games that will never saturate 1.5 GB of video memory on my setup. Darn Far Cry 3 does not work.   I'm ranting, namely. At the same time being a little in-depth play play of this recurring problem.

  In case the VP and general manager or anyone else to Microsoft is approaching through it all here is the short version:

  Video memory leak in Windows 8. How can I fix this in the Windows desktop. Is there a way to erase the GPU cache and reduce the use VRAM 160MO? is there a fix? is there a value from regedit?

  Hey Marv,

  Thanks for posting your query in Microsoft Community Forum.

  According to the description of the issue, I recommend you post your query in the TechNet Forums. TechNet is watched by other computing professionals who would be more likely to help you.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=W8

  Hope this information is useful.

• The path 'Administrator@VSPHERE.LOCAL.log' and 'noUser.log' in VCENTER 6.0

  Hi all

  I have deployed the plugin in vcenter 6.0 and it is deployed successfully.

  I found the diary of the Virgin in C:\ProgramData\VMware\vCenterServer\logs\vsphere-client\logs.

  But I could not find "[email protected]" and "noUser.log" where my plugin will record all the problems.

  Kindly help me.

  As far as I KNOW vsphere_client_virgo.log contains everything.  Check out server/configuration/serviceability.xml where you can reactivate user logs.

• The URL encoding and decoding in OSB

  Hello
  
  Do we not have out-of-box solution in OSB decode XML that is encoded in URL and encode XML to the URL encoding. If yes how can I do.
  
  It is perhaps a fundamental question. I can't understand. New on OSB.
  
  Thank you
  Sham.

  encode an XML to URL encoding format

  No function out of the box I know, I think that you will need a legend of Java to do... I was wondering why you need that...

  It's the doc... Adding and configuring Actions of legend of Java in the stream of messages
  http://docs.Oracle.com/CD/E23943_01/dev.1111/e15866/tasks.htm#OSBDV164

  See you soon,.
  Vlad

  It is considered good etiquette to the answerers rewards with points (as "useful" - 5 pts - or 'correct' - 10pts)
  https://forums.Oracle.com/forums/Ann.jspa?annID=893

• Extend the AD schema and configure the connection manager

  Hello
  
  I tried to extend the schema and configure connection manager but without success.
  
  When I have the schema in ESSO Admin Console extension displays a success message, but when I check Active Directory for objects that must appear, non of them are there.
  
  Someone can explain to me please what im doing wrong, or give me a link where measures to extend and configure connection manager is explained?
  
  Thank you

  Make sure that the agent global settings (registry settings) for the two machines are the same. These settings define how the SSO client will include (as well as synchronize with the directory). If they appear identical, I would then check to ensure that the customer who does not have a typical AD synchronization (see Add/Remove Programs). If this still isn't your problem, check the DNS of your Inbox (this implies that your non-working client is joined to the domain and log you in as a domain user).

• I have 10 devices all under the same identity of apple my partner can see all my contacts, call logs and use of all other web internet devices. How can I change this, to keep my contacts and call log on my phone only?

  I have 10 devices all under the same identity of apple my partner can view all my contacts and call logs and vice versa.

  The device can also see all internet pages use the devices, but mine isn't... How to get our contacts and call the newspapers private their own device and how can I get to keep an eye on web pages using my children? So how do for my phone, the master device / hand who is in control of access for all, because it has my info from apple id and card credit on all devices.

  Stop sharing an ID first. They are not meant to be shared. Then set the sharing of family. Each individual should have their own code.

• silent install Firefox 27.1 and configuration (homepage, proxies and bookmark)

  Hello
  I am trying to perform a silent installation and configuration for 27.1 Firefox but I'm not able to get the same results I got with the 26 versions and below. For these versions, I used the method described in this link:
  http://www.mockbox.NET/ConfigMgr-SCCM/174-install-and-configure-Firefox-silently
  But for Firefox 27 creating the Mozilla.cfg and other files doesn't seem to work. Could you please tell me how silently configure the proxies and the homepage on Firefox 27.1 during installation. I also need to add a bookmark while installing. Could you please tell me how to do the same? I found a few methods saying that I had to change a bookmark.html file, but I don't think that this file is present on firefox 26 on.
  Thank you in advance.
  Kind regards.

  Learn more about this add-on.
  
  https://addons.Mozilla.org/en-us/Firefox/addon/cck2wizard/

• Do I need to install and configure WiFi? (I just want to use it for my iPad on any TV for presentations in mirror)

  Do I need to install and configure WiFi? (I just want to use it for my iPad on any TV for presentations in mirror)

  Yes

• Linear encoder

  Hi all

  I want to record the signal position (rotation). If there are 1024 pulses per revolution, I want that signal position to increase fitted (1023,1024, 1025...). I use linear encoder or angular encoder (of DAQmx creat virtual channel).

  I use NEITHER-9411.

  Thank you!

  
  

• I got a new open word doc and is logged when Windows Vista did an update automatically and restart, now I seem to have lost

  original title: lost document

  I got a new open word doc and is logged when Windows Vista did an update automatically and restart, now I seem to have lost! Any suggestions? A system restore wouldn't work?

  If you have not saved the document before the reboot - and Windows always give a lot of warning before restarting automatically - while the file disappeared.  There is no way to recover; System Restore does apply to system files, not data.