Linksys E4200 Port Local speed

Similar Questions

• Linksys E4200 - range WUSB600N V2 / signal issues

  Router Linksys E4200 dualband and Win7 64 bit Linksys WUSB600N v2.
  Both in the same room, the distance is about 10 meters.
  I compare the results on 5 GHz btw the stick of Linksys and btw another laptop with Intel Advanced-N 6200 AGN wifi chip.
  Running a wifi 5 GHz N on the stick of Linksys, leading to the signal strength low and reduced its speed.
  Practically, I can't improve the signal than the Intel + 15 to 20 dB...

  Negligible:

  distance / Intel / Linksys:
  <1 m ="" -26db="">

  5 m /-50 dB /-65dB

  While Intel radio affects 300 MB/s, the Linksys is somewhere around 200 MB/s only. in the same room
  Anyone else knows a bad signal with the WUSB600N v2, as well? I bought the stick to stream HD media, but with - 65dB is not much of an improvement to what I had on 2. 4 Ghz, 802.11 g (())

  Sorry, but how is this releated response must keep the problem I described?
  disable the firewall on the router spi?
  I checked the possibility of automatic channel selection and channel 20-40 establishments width (automatic channel selection does NOT work correctly from either). I still have the experience that the stick has lower than intel one signal. regardless of the setting of the router firewall 

• Linksys E4200 and VoipBuster sip call

  Hello

  Just recently bought a router Linksys E4200 and it was rocking so far! I've updated since a WRT320N. However it seems that the call SIP (using my account Voip Buster) no longer works...

  I don't seem to be able to register with the Voip service. Port is 5060 standard (if I remember correctly, I'm not at home now) and I've already enabled on the router the special tick for Voip calling ALG. Router is upgraded to the latest firmware and it's the V1 router.

  With all the foregoing, I cannot yet connect to VoipBuster using SIP. It worked like a charm with the WRT320N, so it's something with the router.

  Can anyone help? Thanks a bunch!

  Try the following steps:

  [A] with the help of the Cisco Connect software (if at all, you have installed the router using this software)

  1] open the software and go to the option that says "settings of the router.

  [2] then click on the option that says 'Advanced settings', which will take you to the router configuration page.

  [3] lower the MTU (Maximum Transmission Unit) of 1500 to 1400 or less (usually found on the main page / basic configuration of your router)

  4] click administration and disable UPnP.

  [B] If you have not installed Cisco connect then you can connect to the router's user interface using its default IP address in the browser which is 192.168.1.1 and enter "admin" as password empty username field. This will take to the web interface of the router and then follow the steps as indicated above to make the changes.

  Second, it also depends on the type of VOIP provider, you must open the ports on your router. H.323 uses 1719 and 1720 for signaling, dynamic ports for media. SIP tends to use 5060 for signage, dynamic again for the media.

  Follow this link and open the ports on your router to your VOIP: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=17241

• Ports high speed USB Equium A100

  I installed a webcam Advent (before exchanging it for a better creative). Part of the installation process involves installing a Microsoft's USB controller. (OS is Windows XP Home Edition). I uninstalled the ADVENT software when I got back to the webcam.

  Since then, I started getting messages every time I plug a USB device, on a device high-speed, requiring a port high speed.

  When I look in Device Manager, I have two sets of Bus USB controllers:

  One includes 2 standard OpenHCD USB host controllers, 2 USB, 1 support 2 USB hubs and USB printing composite devices. Their drivers are dated 2001.

  The other includes 1 class PCI USB 2.0 enhanced host controller and USB Root Hub Device 1. Their drivers are dated 2006.

  I have 4 USB ports and all seem to be using the first series of USB controllers. If I disable one of the controllers, then various USB devices stop working.

  As my laptop is only 18 months old, I would have thought that all USB ports are 2.0 version?

  How can I 'forcing' the laptop to use the second set of controllers?

  Hello

  I think that the biggest problem, it is you would waste more time to fix such a driver related issue then just entering the recovery CD and performing a recovery of your entire system.

  Perhaps the fastest way to put little life back to your ports USB 2.0 high-speed. Otherwise, I had suggested to remove all ports from the Device Manager and let windows after a restart re-install all the drivers, but before perform the reboot it would be better to manually remove all THE drivers installed previously.

  Maybe it helps, but if not he would have definitely better to perform the recustomization...

  Concerning

• Linksys E4200 - can update firmware and roll backs damage my router?

  Hello

  I had to restore the firmware on my Linksys E4200 (v2) because I had problems after upgrading the firmware. I tried to upgrade again and again met with problems. In short, I improved a few times and restored several times. Currently I'm on the old firmware and I without any problem.

  In the old days, it was not wise to update the firmware of some peripheral hardware too often, because some devices has agreed that a limited number of updates to firmware... don't ask me why :-)

  Is this also the case with the Linksys E4200 or can I upgrade and roll back as often as the requires, or as often as I want to try to upgrade because of new features...?

  Thank you

  SJW

  As long as you do the right steps during the upgrade/downgrade the router (loading the firmware using a wired computer, not to interrupt the upgrade/downgrade process, load the right file, etc.), the unit should be fine.

• Linksys 8-port befsr81b and CR-smcd3g cable/dsl router

  Hello

  WAN port on my linksys befsr81b router is connected to comcast cable modem smcd3g-ccr, all the cable modem ports are in auto mode and when I connect to the cable modem it shows 10 Mbps, half-duplex, for this linksys router port is connected to.

  When I connect a PC to the same port on the modem using the same wiring, I get 1000Mbps, full duplex.

  He tells me that the router and modem cable have difficulties at ports the correct port mode. When I change from auto to 100 Mbit/s, two-way, cable modem, the router disconnects and the link light for the modem port shuts.

  I use the version of the firmware 2.45.10, June 3, 2004, on linksys router, which seems to be the latest firmware for befsr81b.

  Can someone tell me what could be wrong with my router or its settings?

  Thank you

  digimonx

  It will not work. The WAN port on the BEFSR81B working on 10Mbps.

• Linksys E4200 - Skype internet killing

  Hello

  Recently, I went from a router D-Link GamerLounge for a new Linksys E4200 using the default firmware, upgraded to the latest version.

  The router seems to work fine - except when someone uses Skype, and performance of the network decreases drastically. I have tested it with Skype running on a wireless laptop and test my Wired PC network. Here are the results of ping www.google.com with and without Skype:

  Without Skype (wired PC ping):

  Reply from 74.125.113.103: bytes = 32 time = 132ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 83ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 183ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 105ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 48ms TTL = 46

  With Skype (running on the laptop wireless, PC ping wired):

  Reply from 74.125.113.103: bytes = 32 time = 132ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 83ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 183ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 105ms TTL = 46
  Reply from 74.125.113.103: bytes = 32 time = 48ms TTL = 46

  I searched a bit on the internet and have not found anyone with a similar problem. Someone at - it suggestions? I guess I could try to upgrade the firmware again or something.

  Probably due to the quality of service. You said it was a GamerLounge, which I suppose has automatic QoS for the games.

  You can configure QoS on the linksys as well, it's just not the installer for the game by default.

• Device 4 ports high speed USB 3.0 Hub useful Para PC computer

  Hola amigos

  Al enchufar el 4 ports high speed USB 3.0 Hub useful Para PC computer
  a mi PC, e me lights luz roja, pero no me works, porque me da error code 43 Windows.
  Me pide UN driver y no me lo reconoce.
  Intento find a driver there still no lo he achieved
  Alguien me can help, a packaged good
  MUCHAS gracias
  A greeting

  Hello

  You created this thread in the English version of the Microsoft Community. Please could you click on the globe icon to the world at the bottom left of the screen and then choose your preferred language. Now create your thread again.

  

  If you can't find a suitable language, please go here:

  http://support.Microsoft.com/common/international.aspx

  for other international support options.

  Thank you.

• Linksys e4200 with wifi direct does not connect to the kdl-48r470b

  I just bought a Sony kdl-48r470b tv of the grand prix of Wal-Mart and image, but with the info on this tv being ill not do now to the community for help here.

  Im trying to connect the TV via wifi direct to my router from linksys e4200. the router has wifi direct.  my pc is connected to the router via a network cable. the idea here is that I want to push films to the router, then to the tv via wifi direct.

  the problem is that the tv refuses to connect to the router told me just recording failed. Ive tried the pin of my router still nothing ive disabled the security still has nothing, Ive used the method push button and still nothing.

  is it possible to connect to the router? IM thinking this way because it has direct wifi.

  I contacted sony 3 days ago and have received zero responses from them

  Thanks in advance for your suggestions

  So what you saying is this TV is not able to sell the linksys router? I'm still so confused with this TV... If it says built in wifi, you should be able to connect to your router... looks like there should be a way...?

  very irritated by this situation!

  Thanks for the quick reply... too bad sony can't come back with me with a solid answer... or I could at least understand the rep...

  Denise

• E4200 Port forwarding

  I would like to open a couple of ports in an E4200.

  The only option I can find is in the game.  Can I port before a single port as 3389 to a system on the local network, and it works.

  The problem is that port 3389 is open on the world now since I can't find a way to only allow traffic on port 3389 from a specific static ip address.

  It is a big security problem for me.  I want only the traffic on port 3389 of specific static.

  I also noticed that you can't say different two before port 1433 from a static IP address.

  I hope that LInksys has a way to do it, or it's really a porrly even designed device for residential users

  You can not normally port forward to two or more IP addresses. I've heard some router but can it would be an effect of Robin.

  Yes with the firmware on this router Linksys is impossible to specify an external IP address in the port rule forwards. You can change the external port to something, no standard as 10001 and have internal port 3389. The specify the port and the Address\DNS IP in the computer text box office remotely. Ex: my - distance - ip:10001

  This will only cause confusion, but perhaps that's pretty and your server security settings is always the final measure.

• WAP610N Port Ethernet speed

  What is the speed of the Ethernet port that connects the WAP610N to the local network. Why is it not mentioned on the box or the manuals? I guess it would be 1 GB because what is the meaning of facilitate a 802.11n wireless network when the speed of the connection to the cable network is anything but 1 Gb, I am mistaken?

  The speed of the Ethernet port is 10 / 100 Mbps.

  http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=19927

• E4200: Port before releasing for WOL?

  Some routers are capable of transmitting to broadcast directly by sending a port to 192.168.1.255, the other I was able to trap by transmitting to 192.168.1.254, and then editing the arp with 192.168.1.254 table <->ff: ff: ff: ff: ff: ff. Is there a way I can edit the E4200 arp table? Is there a way to telnet in or get a console connection?

  I activated successfully WOL through the E4200. My guess is that it works with most of the other Linksys routers. First, however, I would ask that Cisco has just enable this through their Web UI, this clearly isn't a big deal and a simple update (modification of javascript is all it takes). Please Cisco, do right by your customers.

  First, I created a port rule for port 9 UDP to *.254 forward (for most of you * will be 192.168.1).

  Then, I went on the button "Booking DHCP" and filled the form to "Manually add Client." My client called "wol" (yours can be anything). My etait.254 assigned ip address and the MAC address can be anything, you can simply copy and paste a MAC address that is already on the page and change the last digit...

  When you click on submit, the form is validated by Javascript; the form is not actually submitted until you press the "Save Settings" button.

  Before you save the settings, I activated the plugin Firefox "Tamper Data". This allowed me to change the form POST request before you actually send to the webserver built into the router. It is a little messy, but simply replace the MAC address that is appropriate in the field of the new customer.

  Presto!

  It's too bad that there is a silent Javascript validation, blocking a very useful feature for this router. A feature which can clearly already handled by the firmware.

  Once again, please do right by your customers, Cisco.

  Enjoy,

  Matt

  PS - This method could have an extra step. I will try using Tamper Data for entrer.255 in port forwarding form directly when I get a chance. If someone is able to do this, let us know!

• Cisco Linksys E4200 v2 fails to process UPNP requests

  Bought a new router E4200 v2 version last month and replaced my dlink dir-655 and I started to see the alerts on my server at home that it is impossible to configure the router.

  Already checked on the router that UPNP is enabled. already tried disabling the firewall, ipv4 and ipv6 and turning too wide "filter applications anonymous Internet", but does not

  then in WHS 2011 troubleshooting guildline, I ran a router online test tool: http://www.microsoft.com/windows/using/tools/igd/results.mspx

  and all tests passed except "Testing UPNP" and the poster details a mistake:

  'Test 5 - UPnP Support Test not supported

  Result:

  The operating system is Windows Vista
  The firewall is turned on

  Exceptions are provided by the firewall

  UPnP is enabled by the firewall

  UPnP services are running

  Discovery of UPnP is enabled

  Detect Internet gateway on the network devices

  2 RMI (s) found

  The IGD device information:

  Name manufacturer: Cisco

  Model name: RMI

  Model number: v1.0

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  get_StaticPortMappingCollection() returns NULL IStaticPortMappingCollection

  Could not get the IGD port mapping ".

  Now, it seems that my router is bad or cisco/linksys does not support this API and is not compatible.

  is there a way to fix this?

  * Firewall can block almost all of the ports used by P2P clients. Check if the BitTorrent ports are made available to customers requesting. Disable the firewall of the router and enable uPnP features allow the BitTorrent ports to pass through.

  * As E4200 is a new Cisco router usually have a good level of security, and unless you have a good configuration configured on the router it can block the software work that uses UPNP.

  * If the ISP updates for IPV6 nodes still functionality for IPV4 will exist as the Lauch of IPV6 also depends on the hardware compatibility

  So, once reset the router for Hard Reset 30/30/30

  The following procedure will clear the NVRAM and set the router back to the default values:

  With the power on, press and hold the reset button the back of the unit for 30 seconds
  Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
  Plug in the appliance ALWAYS keeping the reset button a final 30 seconds...

  Then reconfigure the router once more and then check the concern...

• Linksys E4200 and connectivity Motorola SBG6580

  Here is a picture of my home network. The problem I'm having is, I can't get the WD MyBook Live Duo to be seen on the entire network. If it is connected to the Linksys, all computers connected to the Linksys can see it, but not those related to the Motorola. If I put it on the Motorola, the same thing happens, but in the visa versa. I bought the Motorola for its DOCSIS 3 capabilities, not for the wireless. I prefer to use the Linksys Wireless. Any help would be greatly appreciated.

  

  Devices must be on the same subnet (e.g. 192.168.1.x) to be able to see each other. You could make the Sb IP 192.168.1.1 and 192.168.1.2 for the E4200 and connect a cable from LAN of the SB E4200 (not WAN) port lan port.

  Here is a guide if you need: http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=3733

• Portege Z30-A-12N with Port Replicator Port Hi-Speed USB III problems

  Hi all

  I have a big problem with my new Portege Z30-A-12N and Hi-Speed Port Replicator III.

  I connected the power, DVI, LAN, mouse and keyboard to the Port Replicator.
  Power, DVI and LAN are okay, but none will be found if I connect something to the USB Ports 2.0 or 3.0.
  No mouse, no keyboard, and no USB key.

  When I start my Portege I must enter a password after you press the power button.
  These password, I could enter with the external keyboard, but in windows, no keyboard has been found.

  If I connect the keyboard and mouse to the USB Ports of the Portege instead of Port Replicator, the two has been found.

  I ran Windows 7 Enterprise on the Portege.
  BIOS version is 3.30

  Do you have a solution for me?

  Hello

  The HI-SPEED PORT REPLICATOR III PA5116E-1PRP supports 2 x USB 2.0 and 4 x USB 3.0 ports.
  You n t special need Win 7 drivers in order to be able to use the USB ports or other interfaces such as VGA, DVI, audio, etc.

  Sound problems, make sure that the audio device has been selected in the right panel-> sound-> playback tab

  By the way: Win 7 needs USB driver 3.0 which is preinstalled when the laptop was equipped with USB 3.0 ports. My knowledge if your mobile phone does not support USB 3.0, you will be able to use the port replicator USB 3.0 ports.

  Finally and above all devices must be connected before you start the computer. The decision supported and compatible specifications: Portégé R30 - A, Tecra Z40 - A, Tecra Z50 - A, Portégé Z30-A/Z30t-A, Tecra A50 - has