Location System Board FRU T400

Similar Questions

• Re: Need to motherboard / system board for Qosmio G20 106

  I would be grateful if anyone can help me find one.
  My laptop is dead now and need a mother replacement on board.

  Please also provide you with the best suggestions to find the online store for the system board. I searched for the part, but unable to find it.
  Thanks in advance.

  PS Many people have serious problems with this type of model, mainly with the cooling system! It's my first pc/laptop and I want it to work again!
  Motherboard: fnn 2 s 1 a5a001404010

  Hello

  All parts can be ordered from local Toshiba ASP.
  Contact Toshiba service provider in your country and order this compatible part.

  But note; It s not cheap part! The replacement of the motherboard is still an expensive procedure

• Qosmio F20 system board failure

  I recently returned to my out of warranty F20 for Toshiba service partner for diagnosis and have been informed that the system board must be replaced due to graphical corruption. The cost for this is £500.

  Reading through this forum, there seems to be a story of what is happening on the Qosmio. Someone at - he managed to get Toshiba agree that it is a design flaw?

  [Edited by: admin]

  Hi Roachaldo

  I don t think that it is a design flaw.
  The fact is that the Qosmio is a portable high-quality with a lot of devices.
  In addition the laptop uses a technology that is very sensitive as a module of desktop PC and these problems might not always appear on the Qosmio laptops but on different models of mobile phones.

  It of a really bad luck that your motherboard is dead after the laptop was out of warranty, but this has nothing to do with the quality of the Qosmio. I have a Qosmio G20 (similar to F20) and it works properly. Have no problem.

• X 2 system board split

  I have a Split 13 x 2 m110dx PC with processor i3 and I wonder if it can be upgraded to a map of the System i5 and if it would increase the speed/performance enough to be worth the effort. I found the part of Intel to 295.00, which is almost as much as I paid for the system. I've updated the 8 GB RAM, that helped a lot, but I'm used to a little more speed. Any advice?

  The processor is soldered to the system board. The fastest system is:

  Card system for use with Windows 8 models with processor Intel Core i5-4210Y (includes processor and replacement of thermal equipment) 749775-501

• 17 - f053us: ID of the system board

  Model # 17 - f053us

  Product # G6R30UA #ABA

  I bought this laptop about 16 months ago, and today the two port USB 3.0 does not have any powers to the ports. The works of 2.0 port.

  I want to replace the motherboard, but I'm having a hard time finding the part number for the to the system board.  I was hoping that I have would'nt need to disassemble to get that number.  With the information provided is it possible to identify the Council?

  Yes, you look to the top of the plug and see what processor and video, he has then find in the manual and find this:

  AMD A8-6410 (2.4 GHz/2.0 GHz, 2 MB L2, 1600 MHz DDR3L, quad core, 15 W) for use with Windows Standard HP Pavilion 17 Notebook PC 763422-501

  Good price good eBay seller:

  http://www.eBay.com/ITM/new-763422-501-HP-Pavilion-17-F024-A8-6410-STD-motherboard-/152102614339?hash=item236a05b543:g:LZEAAOSwepZXRPex

  Amazon.com:

  http://www.Amazon.com/763422-501-HP-Pavilion-motherboard-A8-6410/DP/B01C15W1AS?ie=UTF8 & Keywords = 763422-501 & qid = 1465334776 & ref_ = sr_1_1 & SR = 8-1

  HP Partsurfer:

  http://PartSurfer.HP.com/search.aspx?SearchText=763422-501

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP 635 Bios message at startup - System Board OOA - Productname & Serialnumber missing

  Hello

  I have a HP 635.

  For a few days he told me to start missing Productname & Serialnumber.  (Map of OOA system)

  I checked the Bios Setup and these fields are indeed empty... (Modelnumber & Serialnumber)

  The message came out of the blue... Has nothing to the laptop. (Works great!)

  Version of the BIOS F.48

  How can I put back model and serial number in the bios? I tried F10 and CTRL + A, but it will emit beeps at me right there...

  Jacob67 wrote:

  Hello

  I have a HP 635.

  For a few days he told me to start missing Productname & Serialnumber.  (Map of OOA system)

  I checked the Bios Setup and these fields are indeed empty... (Modelnumber & Serialnumber)

  The message came out of the blue... Has nothing to the laptop. (Works great!)

  Version of the BIOS F.48

  How can I put back model and serial number in the bios? I tried F10 and CTRL + A, but it will emit beeps at me right there...

  Hello

  Go into the BIOS and "Load optimized Defaults". It is reset the BIOS to its default values. If this does not work, try this:

  http://www.diypcguide.com/how-to-fix-system-board-OOA-or-missing-system-information-or-product-information-not-valid-HP/

• System Board pavilion dv7 7099el

  Pavilion dv7 7099el

  Windows 7

  System Board missing info startup error message

  On-board system (00 a) name, number, Configuration, family

  My system borad has been changed and this error on startup rises... There are no other numbers or codes.

  Any help?

  Hello

  You will need to contact one who changed your system board that this information should have been "tattooed" on your replace bios chip.

  Kind regards

  DP - K

• VMware ESXi 5.5 - System Board SEL_FULLNESS 0... 100 unknown

  Hello community,

  I'm going to have that kind of alarm on VMware ESXi 5.5 - SEL_FULLNESS system board 0...

  How to solve this problem?

  vmware_logs.PNG

  

  Greetings.

  You want to connect to your MMIC and clear log SALT.

  Fullness SALT refers to full journal SALT is.

  The journal SALT allows only a certain number of entries before becoming full.

  Thank you

  Kirk...

• ESX04i on HP DL385 G2 sensor error: System Board 2 ProcHot - limit exceeded

  Hello everyone,

  I installed a server esxi to a hp dl385g2 (8.50 firmware). After the first start, a sensor after the following error message:

  System Board 2 ProcHot - limit exceeded?  ?:|

  can someone tell me what kind of error this is?

  THX

  Mike

  Just download a previous HP firmware CD

• Location of the FRU jury system

  Where can I find the FRU on the motherboard? I have already deleted the keyboard but cannot locate the number.

  I need a new system for model T41 2373-7FU Board.

  Thank you...

  Thank you.

  Got the FRU part number.

  I found the part number FRU for card system by removing the low SO-DIMM.

• Create installer problem - locate System Driver Set - may 2016

  Hi guys,.

  I use LabVIEW 2016 (64-bit) and I try to make an installer. During the Setup, installers, LabVIEW suggests that:

  • OR LabVIEW DURATION 2016 (64-bit)
  • NOR-488. 2 DURATION 15.5
  • NI-VISA DURATION 15.5

  When I build, I get a request to locate a number of other installation programs (so far as I know), I've hosted, but whatever I wonder at the moment, I can not find: 'National Instruments System Driver Set - may 2016'.

  

  The only driver sets that I can find on ni.com end to April 2015 and that the file is massive (more), which seems like overkill for what I'm trying to do.

  In addition, my software only uses the RS-232 port and any other material.

  My questions are:

  Where can I find this set of drivers?

  Is it possible to see specifically which driver the build is looking for?

  Thank you

  Adrian

  -I just googled a bit and found this

  -From the link above, I've just went to the parent directory and found this:ftp://ftp.ni.com/support/fis/sds/2016.05 which I believe is asking, and it's even bigger 11FR.

  p.s. I'm not sure if this will help or not.

• Pavilion dv6t-1200 Notebook System Board part number identification

  I am obliged by replacing the Board system/card mother for model Pavilion dv6t-1200 FV161AV (grilled, painful, do not ask :-().  The maintenance manual identifies 5 part numbers of possible candidates.  I eliminated three of claim, but I can't do it between two others to identify and order I need.  The two remaining candidates are listed as:

  511863-001 for models with graphical subsystem UMA memory

  518433-001 for models with UMA and GM47 chipset graphics card

  The processor is a Core2Duo T6400 (labeled AW80577T6400; 2.00/2M/800).  Two other large chips are the I/O chip that is an Intel AF82801IBM (L920NA92; SLB8Q ' 06 Taiwan) and chart/memory chipset called AC826M45; SLB94; EB920A510 and contains a logo Intel "i".  The I/O chip does not say much, but when google, seems to have associated the GM45 many including the GM47 is a member.  However, the AC826M45 seems to be a member of the Intel 845 chipset family.  The first suggests the 518433-001, but the latter suggests the 511863-001.  The FV161AV also seems to get associated with the 518433-001 in the vendor's documentation, but it varies.  Photos on the Internet have insufficient resolution to compare with the current motherboard to see who is right.

  Are there references that a person (for example at HP, perhaps) is that he or she can check to disambiguate on this?  I have included all the reference numbers as I could but if more are needed, please ask.  Any help would be welcome and thanks a lot in advance.

  Never mind!  I didn't know that there was a tag just below the memory.  All this time, it was under the memory.  I removed the memory and there it was:

  518433 001

  And I spent hours trying to understand some chips that did not exist on the Board of Directors.  These are the times you think that you are being so smart, but prove that you can be stupid enough.  Sorry for the inconvenience.

• How to change the serial number when the system board is replaced

  How can I change the serial number of the system in the bios of a D530 SSF when replacing the motherboard?

  Hello:

  I suppose that if that's all you can do with this utility, then it of all you can do.

  I do not think I said that the utility likely to modify or add the model number, nor asked the question originally.

  You will need to contact HP technical support and have a technician HP bios with any other information you need to tattoo.

  Paul

• product information programmed into the system board are invalid or missing

  the following product information programmed on the system card is missing or invalid

  WHAT information?

  Without providing us with all the details, we can not help you...

• How do l fix doesn't have system board problem RTC accuracy test

  Hello

  When running my PC Checkup(system tests), l has a problem, the overall result of the test revealed that the card system, RTC accuracy Test
  WSBO1-HWX failed. How do l fix the problem so that the RTC accuracy Test will pass in the future?
  Kind regards
  Amos.

  Hi, Amos.

  What is your computer make and model and the Windows operating system?

  RTC - this test accuracy test verifies the accuracy of the RTC on the motherboard and compares it to the processor clock to determine if the motherboard and CPU clock are too out of sync. This test will discover problems with updates of time system, periodic interruptions and interruptions of the alarm. If the test detects errors with the accuracy of the RTC, it will record the test failure in report of the additional details in the test log.

  Your Windows system time may not be the same as the Bios time.

  Check in the Bios

  Compare with time Windows

  If the clock keeps losing time, check the battery

  You may need to replace the CMOS battery