Lockout Ganymede, define the interface VLAN bad

Hello

In the middle of application and test the new configs GANYMEDE, I put the t 'GANYMEDE SOURCE INTERFACE IP' to the VLAN evil. My mistake and fortunately, I tested on a switch that is not really used. So I tell myself no case submission, I'll disconnect the trunk and move the console with the user name, with my understanding that if no RADIUS server is available, the local user name would be used. Well the name of username/password combo is not correct or the theory of "not being able to communicate with radius server, so use the local username" is not correct.

Anyway, anyone have any ideas? Perhaps a password recovery can change the username password and fix VLAN?

Thanks for your help...

Hello

If you are not able to access the switch, simply do a recovery of password for the switch. you would be able to access the switch and change the configuration.

It is based on the orders of AAA configuration for authentication if you gave Ganymede then local authentication if the aaa is not accessible...

Thank you

Please rate if useful...

Tags: Cisco Security

Similar Questions

  • SG300-20 - configure DHCP on the interface VLAN

    I have read the different partners of the discussions on the SG300 and SG500 going on regarding the high setting of VLAN and DHCP on VIRTUAL networks.  For some reason, I could not get even this simple task to work.

    First thing I did was update my version firmware and boot as follows:

    SW version 1.3.7.18 (date of 12 January 2014 time 18:02:59)

    Start the 1.3.5.06 version (dated 21 July 2013 times 15:12:10)

    HW version V02

    When I rebooted the SG300 after the SW/Boot updates the boot configuration has been crushed and I had to configure my switch from scratch.  The intention is to have two VIRTUAL networks:

    VLAN 1: all the devices, servers, etc.

    VLAN 2: subnet basis which distributes DHCP addresses

    The SG300-20 is connected to a router Asus RT-AC66U on the 192.168.1.x subnet and provides access to the internal network and WiFi access (IP address of the router is 192.168.1.1 and the default gateway).  Everything works without any problem.  So my task is simply to create 2 VLANS on 192.168.2.x subnet and use DHCP to assign addresses.  I spent many hours on it and I still can't get it to work.  When I connect a laptop to the port (GI8) assigned to 2 VLANS, I end up finding a few wobbly 169.254.x.x address.  I definitely thought something would not 'easy' that hard to set up, but apparently I was wrong.

    The SG300 is running in mode L3 as shown in my running-config below.

    Someone gets to see something which could prevent my client from the laptop to receive the interface VLAN 2 DHCP IP addresses that are not on the 192.168.2.x subnet?

    Any ideas / suggestions would be greatly appreciated!

    Here's my running-config:

    config-file-header
    MYSTICSW1
    v1.3.7.18 / R750_NIK_1_35_647_358
    CLI v1.0
    router adjustment system mode

    SSD of encrypted file indicator
    @
    SSD-control-start
    config of SSD
    control of password file unrestricted SSD
    no control of the integrity of the file ssd
    SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
    !
    database of VLAN
    VLAN 2
    output
    Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
    Add a voice vlan Yes-table 00036 b Cisco_phone___
    Add a voice vlan Yes-table 00096e Avaya___
    Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
    Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
    Add a voice vlan Yes-table 00d01e Pingtel_phone___
    VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
    Add a voice vlan Yes-table 00e0bb 3Com_phone___
    Hello interface range vlan 1
    hostname MYSTICSW1
    host 192.168.1.15 record
    logging source hostname id
    username privilege 15 b4a0fcf20b2cd9d80a55b06ab8f83277f9733904 encrypted password cisco
    location of the SNMP-Server Office
    clock timezone ""-5
    DST Web recurring U.S. clock.
    clock source sntp
    unicast SNTP client enable
    unicast SNTP client survey
    survey of 192.168.1.10 SNTP server
    !
    interface vlan 1
    IP 192.168.1.254 255.255.255.0
    no ip address dhcp
    !
    interface vlan 2
    name MysticWAN
    192.168.2.254 IP address 255.255.255.0
    !
    interface gigabitethernet8
    switchport mode access
    switchport access vlan 2
    !
    output
    Default IP gateway 192.168.1.1

    Thanks in advance!

    Clint Lambert

    Clint, please see this post

    https://supportforums.Cisco.com/message/4178990#4178990

    -Tom
    Please mark replied messages useful
    http://blogs.Cisco.com/smallbusiness/

  • F10 4820 t - pulsations on the interface vlan

    Hello everyone

    Using Force10 S4820T on 9.6

    Rate limits can be applied to the physical interfaces only? and if yes how can I do to fix a speed limit on an interface vlan? Policy-map?

    Thanks in advance

    Based on the information contained in the user guide, it seems that it cannot apply to the physical interface.

    Page 739:

    http://bit.LY/1IRtdlU

  • Assign IP address to the Interface VLAN of Web Admin?

    It is a simple question, I can't find can in the web config page to assign an IP to an interface vlan.

    Example: I create a vlan 40 and assign ip 192.168.40.254/24 to it, I can accomplish this with the CLI with 'config; interface vlan 40; "192.168.40.254 IP address 255.255.255.0" but it does not seem to exist in the web interface!

    Thank you
    Scott


  • The interface VLAN ACL of inbound traffic?

    Hi, I may be over thinking this, but I have an ACL that is applied when entering an interface vlan. I have a line to allow udp any any newspaper which is temporary. I see hits, but the source ip address is outside the network to the ip address of the destination interface vlan. I expect to see ip source addresses only in the range of ip addresses of 192.168.1.128/25. What do you think? Thank you

    Interface vlan 100

    IP 192.168.1.132 255.255.255.128

    IP access-group ACL_IN in

    Hit of the ACL

    % S: SW1-6-IPACCESSLOGP: list of the allowed ACL_IN 192.168.6.100 (137) udp-> 192.168.1.132 (137), 1 packet

    Hello

    That looks like to me WINS navigation, a response packet.

    And as MS navigation works at level 2, it sends a response to the IP of the router where he sees demand for travel coming - maybe your customers have a configured WINS server address?

    Do not forget
    allow udp any any newspaper

    will match ANY ip src, not only your local subnet and is why your journal entries show the traffic in both directions.

    Rgds

    Ian

  • Defining the interface of the scale to 200% in Photoshop CC 2015 does not work.

    Title says it all.  I have change the scale to 200% to take into account my 4K monitor and restart Ps and my computer does not change it.  Is there a solution to this?  Thank you.

    Can you show two screenshots like this.  I opened CC 2015.5 Edit preference Interfaces, it has shown 100% IU. I have PRTSCN to copy the screen to the Clipboard. Change IU 200% hit OK and close Photoshop.  Open Photoshop opened a new document Clipboard format and Pasted in the screenshot. 100% relative additional canvas. Change preferences Interface saw 200% and click on Prtscrn to screenshot. 200% changed to 100% and click OK. a Pasted in the second screenshot an aline layer down, you can see the Interface preferably did not fit my display 1920 x 1080 to scale 2 x it becomes a display 960 x 540 and responds PS status of 1024 x 768.

  • ASA 5540 - cannot ping inside the interface

    Hi all. We have recently upgraded PIX to ASA5540 and we saw a strange thing going. In a Word, we can ping the inside interface of the ASA from any beach on our 6500 network (which is connected directly behind the ASA on the inside), but one where our monitoring tools are placed. Inside there is an ACL that allows all of our core networks, but it does not help that the interface is really strange.

    In the ASDM, I see messages like this:

    ID ICMP echo request: 2004 x.x.x.x y.y.y.y on the inside interface to. I don't think that's the problem, but I could be wrong.

    This is also the configuration of the interface VLAN VIRTUAL local area network from which we cannot ping inside the interface we can ping to and since this VLAN and machines without problem. The only problem is ping the inside interface of the ASA.

    interface Vlanx

    IP x.x.x.x 255.255.255.0

    IP broadcast directed to 199

    IP accounting output-packets

    IP pim sparse - dense mode

    route IP cache flow

    load-interval 30

    Has anyone experiences the problem like this before? Thanks in advance for any help.

    Can you post the output of the following on the ASA:-

    display the route

    And the output of your base layer diverter: -.

    show ip route<>

    HTH >

  • Interface VLAN SG300-28 Firmware 1.3.7.18

    Hello

    I just my SG300 to update the last firrmware 1.3.7.1.8 and I met this problem:

    -By default, the interface VLAN has been activated, but the display is always disabled

    -I can not change and I can not ping to the VLAN IP interface as well (I gave an IP 192.168.10.1)

    Is this a bug? Does anyone know how to fix this? Please help me!

    Appreciate your help

    Minh

    minh06,

    You upgrade the startup code for Sx300_FW_Boot_1.3.5.58 ?

    -Marty

  • SG300/SG500 remove interface vlan

    Hello!

    The question is the following:

    I add a VLAN interface to test IP connectivity to this vlan by adding an IP address for this interface vlan and ping on a host.

    for example
    interface vlan 5
    192.168.0.251 IP address 255.255.255.0

    Then I can remove the ip address "without ip address', but I can't delete the ' interface vlan 5".»

    Even when I delete the vlan itself of the database for vlan. There is no command "no interface vlan. I can only stop the interface vlan.

    If anyone knows how to remove the interface vlan switches SG300/SG500 cli.

    Thanks, Woeger

    Hello

    I tried just that with my switch from laboratory here.

    I created VLAN 10 and he has given an IP address.

    Then I did a no ip address on the interface VLAN and then not a vlan 10.

    At this stage there is no interface THAT VLAN 10 in my config running or when I do a show ip interface.

    So remove the VLAN has done actually remove the interface for me, brings me to my question.

    What version of the bootcode/firmware do you currently use?  Maybe this problem has been fixed, because I am running 1.3.7.18 firmware with 1.3.7.01 code to boot.

    If you are on a low moving forward and put to date, don't forget to upgrade the boot thus code, it is necessary for new versions of firmware.

    Hope that help, but if not just let me know and we can take another look,

    Christopher Ebert - Advanced Network Support Engineer

    Cisco Small Business Support Center

    * Please note the useful messages *.

  • All traffic Vlan to the Interface of the Proxy Server

    Hello!

    I need little help to route all the traffic on VLAN to the proxy server.

    I have different VLANS on switches L2 200-26 and by 300-28-L3 for routing.

    I have already created VLANs and able to rout them, but facing problem for routing traffic to the interface proxy for internet access.

    I have different VLAN for example Vlan 10, 10.10.10.0/24 sales, Vlan20 10.10.20.0/24 Marketing. I have trunk between switches interfaces and default 1U is the same on all switches.

    My proxy server has two NICs, one is connected to a dsl modem and other one to the switch port that uses the IP 192.168.0.2 to default vlan1.

    I am able to surf the internet using vlan1 but not on ther VLAN.

    I put the route defaults to the switch of 192.168.0.2, but don't not routing for internet to another VLAN.

    Thank you

    Hello

    To answer your questions:

    1. I have to update the following files?

    https://software.Cisco.com/download/release.html?mdfid=283019617&release...

    Yes, please let me know what firmware and boot code, that you have right now and I'll tell you what is the best way for you to upgrade because you shouldn't go straight to the latest firmware unless you run already 1.3.5.58 or later version.

    2. it supports to 8 dhcp pools. I have swimming pools, but I have more than 8 VLAN. I put all the settings, works very well.

    You are right and I forgot to mention the limitation of only 8 DHCP pools, I'm sorry. That being said, make sure that your current DHCP server uses IP addresses assigned to each VLAN on the switch as the gateway by default for the VLAN respective.

    3 for the Proxy Server, I need to find a way to point back roads of VLAN to vlan mapping static address on the switch. I'm confused in this little piece.

    I understand that this can be confusing, let me see if I can explain it a little better.

    Assuming that everything on the switch is configured according to my recommendations can

    1. you need a single, a route by default on the switch, so that when a PC is connected to one of VLAN on she tries to go online, an unknown IP address to the switch, it will send it to the Ip address of the router, because the proxy server will be able to reach this IP public, unknown to any Web site.

    2 - when the traffic is back to this Web site, it will be intended for another subnet that the proxy server is on. Suppose the answer is looking for 10.10.10.100 (subnet unknown to the proxy server), without a static route on the proxy server it say where to send this traffic, packets are simply deleted.

    3. you need to create as many static routes on the proxy server as the amount of VIRTUAL LANs, you have on your network.

    For now I know that the proxy server is 192.168.0.2 on VLAN 1 but I don't know what the IP address of the switch is on the same VLAN, it should be something on the 192.168.0.x range.

    All journeys should look like this:

    10.10.10.1 255.255.255.0 send 192.168.0.x (IP address of the switch on the VLAN 1)

    10.10.20.1 255.255.255.0 send 192.168.0.x (IP address of the switch on the VLAN 1)

    Alternatively, if all your internal VIRTUAL local networks are on the beach of 10.10.x.x then you should be able to create a single rule to summarize all the VLAN as this:

    10.10.1.1 255.255.0.0 send 192.168.0.x (IP address of the switch on the VLAN 1)

    Please let me know if it was a little clearer.

    Feel free to ask any questions.

  • The interface usb audio of Behringer U-Phoria UMC404HD work with Garageband?

    I just got an interface USB 4 channels for recording guitars and microphones. It has no driver, but instead uses the Mac OS. I implemented the sound control panel to recognize the device input and output, can I use the Audio configuration utility and MIDI to fit a recording at 192000HZ.

    My problem is that as soon as I open GarageBand 192000HZ setting falls down to it is more low 44100 HZ. It is a flaw with the audio interface Behringer or is it a problem of system software?

    I will mix Behringer messages on this problem, a guy says that the interface has a bad component castigates other Garageband.

    I would appreciate hearing from anyone with any interface from Behringer, who used it to 192000HZ using Garageband.  Any other comments welcome.

    I have this problem on 3 different computers using systems to a new installation of 10.11 10.6.8. A few different USB cables. More recently, on an I7 Mini with memory 16 concerts with 10.11.6. Currently on Garageband 10, but the same problem with Garageband 6

    I talked to an Apple technician and the answer is that Apple has "capped" sampling in 441000HZ setting.

    Thus, in spite of the box is designed to accept 192000Hz sampling, apparently GarageBand has been paralyzed for a lower sampling only to the adjustment system. Another program audio I, Amadeus Pro, has no difficulty with the parameter to 192000.

    TSK, tsk Apple...

  • Is it possible to define the image poster in browser FCPX?

    Is it possible to define the poster frame of the browser FCPX to the last frame of the clip?

    My use case:

    I have bunches of clips on a SD card, good and bad, taken from several scenes. Clusters.

    Each bad take is cut while now a red card to the camera. So if I had some way of looking at the last picture of the clips, I would not put the clip in the timeline or skim even the clip had been sloppy and should be rejected. I have confirmed with Canon that our XA25 will only display the first image of the scene. FCPX seems to like to display the middlemost image like the poster. If it is can not editable in FCPX someone Adviser of another method?

    Thank you!

    You can post a screenshot of the place where in FCP you are talking about? The browser may display several images and view film, you can zoom in the film of the clip. There is no single framework for the poster frame.

  • How to query the object module for the interface of the module interface specific, I need

    Hello.

    Currently using LabVIEW TestStand/2012 2012.

    I am looking to change the sequence of LabVIEW text translator, and in the CreateStep.vi I am trying to create a step of type WIS_Sequence_Call (a customized version of NI_Types.ini--> SequenceCall).

    I need set the file path, name and step sequence parameter values.  I think I need to access the SequenceCallModule class to do this.

    This will help the States of SequenceCallModule in the description of the file: "To access the properties and methods of a specific module class, ask the object Module for the specific module interface interface, you want to acquire".

    What, exactly, is "request" here?  It looks to "Clarify" might be what I'm after, but I want that result programmatically, IE no dialog box.

    See my excerpt below.

    Thank you.

    Use the connectivity-> ActiveX--> consider Variant. Define the type of SequenceCallModule, giving the interface as input Module. You must close the interfaces of the Module and the SequenceCallModule when you are finished with them.

    What he does is to call QueryInterface on the entry. The COM Module object implements the interfaces of the Module and the SequenceCallModule in this case to use.

    Hope this helps,

    -Doug

  • Having trouble getting the voice VLAN on the switch X1052P to work at all

    Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

    Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

    Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

    I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

    Network administration > VLAN > VLAN static

    Network administration > VLAN > Voice VLAN

    I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

    This is the short story from where I am now. Any help is greatly appreciated.

    FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

    After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

    I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

    SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

    So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

  • interface vlan problems addin

    Hello

    I have a problem with my 8164F with 6.1.0.1 powerconnect version

    I create the vlan 643

    then I create an interface vlan

    interface vlan 643
    IP 172.24.64.2 255.255.240.0
    output

    When I ping the ip address of the switch

    ping 172.24.64.2
    Ping 172.24.64.2 with 0 bytes of data:

    4 packets transmitted, 0 packets received, 100% packet loss
    round-trip (MS) min/avg/max =<10><10><>

    in the journal, I have the following line

    <173>11 Jun 14:39:29 172.16.8.100 - 2 TRAPMGR [1206213340]: traputil.c (697) 1604 %% link on Vl643 is down

    show ip interface vlan 643

    State of the routing interface... Down
    Primary IP address... 172.24.64.2/255.255.240.0
    Method......................................... Manual
    Routing mode... Enable
    Administrative mode... Enable
    NET before realized emissions... Disable
    Proxy ARP...................................... Enable
    Local Proxy ARP... Disable
    Statement of assets... Inactive
    MAC address... D067. E595.0B1A
    Type of encapsulation... Ethernet
    IP MTU......................................... 1500
    Bandwidth...................................... 10000 Kbps
    Destination unreachable... Activated
    ICMP redirects... Activated

    that really interested me

    I simplified my config and merge the two portchannel.

    and it works.

    I'll come by later to STDs

Maybe you are looking for