locks up PC / gets stuck in standby/hibernation mode

Similar Questions

• Stuck in standby/hibernation mode

  After a long weekend, our computer will boot back upward.  I tried the power proposed, off, remove the battery and drain the power from the computer after having disconnected everything.  Even when the computer reboots, the only thing that happens is the fans kick on, the mouse lights up but not else.   I tried another monitor to make sure it wasn't a problem there.  The lights on the keyboard light up ever.  I can get a model # but I think that it is not a question of model, but something I can't understand.  Any suggestion would be appreciated before that I have to take it to the store.

  Inspiron 570

  He's back on now...  But thanks for the reply.

  Left it unplugged for 48 hours, has changed the small battery inside and cleaned the dust out of it.  It came immediately after the battery change.  Not sure if it was the question or not, but it works like new now.  Just to note, it has not started to work again until the battery has been replaced.

• Satellite U300-144 does not come from the standby/hibernation mode

  Hi, can anyone help?

  I have a new Satellite U300-144 accompanying the Vista home 32-bit preinstallation. I have a problem, he wants to come to the sleep/hibernation mode, and my clear blue power is always on standby/hibernation mode. I hold the power button to restart the computer and then I get a message of illegal closure because I don t shutdown right.

  I tried to upgrade the BIOS later for my model and the n t the problem, then I tried to upgrade to Vista Ultimate t doesn't help either. I installed all the drivers and everything works real well.

  A colleague using me U300 Office. I asked him to check the extended sleep/standby option and he reported that everything works correctly. He always uses the factory settings and only one update is added value package. He kidnapped the former and installed latest version of the Toshiba download page.

  Have you installed latest PPVS too?

• Satellite M30X-111 wake up from standby/hibernation mode

  People, like many of you, I had the questionable connection DC problem and I solved this at the time of re - solder the wandering joint on the connector for the motherboard.

  Everything was fine with the laptop until yesterday when I tried to get the machine to wake from standby / hibernation if it is when you close the screen) and now all that happens is that the blue light around the power button lights up, the CPU fan runs for about 5 seconds, the HARD drive light flashes once Maybe two times and the DVD briefly climb towers.

  Also nothing happens... the screen is blank and the laptop is actually not from the occasional maelstrom of the fan.

  Is it in any case to perform a reset of some sort to get it to snap it on hibernation? I have read up on this subject on various forums and have tried to start without memory, without the HARD drive and the DVD drive and still no life.

  Any input is appreciated that I need this laptop to spring into life again.

  Thanks in advance

  Ground

  Hello

  to wake up the machine, simply remove the battery and the AC and leave the machine for a few hours. After that, it should work again.
  By the way: sometimes it s a good idea to do a biosupdate, because maybe the problem comes from the bios.

  Please give some comments about your success... :)

  Welcome them

• Satellite M115-S1061 - how to activate the standby/Hibernation mode

  I recently got a laptop from my father and the settings are a bit strange.

  My modes standby and Hibernate are also well off and due to the lack of a cooling device, it constantly turns off when I leave.

  So whenever I leave, I have to shut down my computer, then restart again and his old fact.
  I need to find a way to get my laptop to activate the standby or hibernation mode so I can't go through this process each time.
  Its a Toshiba Satellite M115-S1061.

  Also, I checked the options of standby power, and they say the same things as well.

  Thanks in advance for the help!
  -trueway44

  Hello

  The history is confusing for me.
  Just a few questions to the beginning:
  What operating system do you use?
  You use Toshiba power saver or power Windows options?

  If you know that this laptop turns off when you leave why do the restart if you know it goes off even when?

  You let your laptop with no activity, or you leave while an application is running?
  Maybe is related to overheating decommissioning.

• Auto erasing in pro SSD comes from standby/hibernation mod.

  Hallo! Help me)

  I'm on macbook pro 13 "2011 i5. So I bought ssd to upgrade my mac. These are the 128 GB plextor m6pro. I cloned all the disk system ssd. Also I bought optibay, I broke my hard drive cable, so now the whole system works on optibay and ssd (without hard drive).

  I have a serious problem. When I close the macbook and then open after a few minutes my system begins to work is not properly so I click on system reboot and Flash then folder with the question. I like this for 4 times, other times just system opens when I opened my macbook. Then I go to the internet-> disk utility boot and see this ssd is completely erased, no partition! I don't really know what to do.

  It seems that he connects with optibay because it uses cd, mode standby/hibernation and sessions.

  Please help me! =)

  I forgot to add, all the time, I used trimforce enabled, unless it's necessary information. Hope someone could help me.

• Satellite A100-201 stuck after enabling hibernation mode

  My computer is an A100-201 and its dead end hibernation. I read the advice others have written, but I can't get it back to normal. He was weak in power then start to Hibernate / hibernation. by pressing the key power dosen't work I need help. Please

  Hi girl

  A friend of mine called me yesterday because he noticed the same issue. After awakening, he saw just a blue strip instead of the task bar and the screen was black.

  Only solution was to press the POWER button and hold for a few seconds. On this way, you make your laptop to SWITCH OFF. Laptop and press the power button again will start as usual. After reboot, everything will be OK again.

  Please do the same. If you have more problems to write again.

  Good luck!

• Lose Internet connection after sleep/standby/hibernation Mode

  I recently bought a new HP Pavilion Elite e9105z CTO Office and migrated from Win XP to Vista Home Premium x 64, with a NVIDIA nForce 10/100 Mbps Ethernet Controller.  Whenever I come off standby or standby mode, I lose my Internet connection and have to restart my system or run Windows Network Diagnostics to repair the network adapter settings.

  I tried several remedies available on Internet; but unfortunately, nothing has resulted in a permanent solution.  I contacted my service provider ISP (Mediacom) wonder if it was / is a problem with the firmware used to my cable modem SBV5220 support (for example, incompatibility with Vista) and they said there is no.  So far, I have:

  1. Reinstalled NIC driver.
  2. Power options controlled and reset with USB CDC.
  3. Apply the update for Windows Vista (default gateway setting is lost) for x 64 systems (KB933872) - response that update does not apply to the system.
  4. Reset the IP configuration via the Cmd line.
  5. Tab power, unchecked the box that shuts down the adapter then power save comes into play.

  Access the computer several times a day and having to reset Internet connections became extremely aggravating.  I hope there is a solution.  Thanks in advance for your help.

  Back from a 3 week stay, during which my office has been extinguished, my local internet connection would come is no longer active when he came out of hibernation.  The without line worked, but the local connection would not work unless physically, I unplugged the cable from the router (Netgear) and reinserted it.

  After several days of frustration, I went into the Manager of devices, unchecked ethernet optional adapter "allow the computer to turn off this device."
  This seems to have cleared up the problem, at least until now...

• standby, hibernation mode.

  my computer will go to sleep / hibernate without put me there.  will not come out of Standby / Hibernate unless I turn off the cpu.  Don't let even power down of the cpu.  tried to reset the default values in the setting of such power as suggested in the forum.  did not work.

  What make and model ask you questions on. It could be as simple as getting into the BIOS and the quest for performance, or the Management tab.

• Noise after getting out of the Hibernation Mode / start-up

  Hello

  My computer makes a noise when out of hibernation after a long period of time mode (one night). I was stopping and restarting and most of the time the noise disappears.

  What could be causing this please and how to stop?

  Thank you

  Hello

  Please keep us informed about the issue.

  If the problem persists, you can try to start your computer in a clean boot and check the status. If the cause is due to any third-party application or services then it will be detected after the clean boot.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

   

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

   

  Note: See "how to reset the computer to start normally after a boot minimum troubleshooting" to prepare the computer to start as usual after a repair.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Thank you.

• How to disable the standby/Hibernation on series Satellite Pro U mode

  Hello
  I have on my Satellite Pro U installed Windows Vista professional series.

  During the defragmentationprocess my machine automatically goes to sleep.
  Does anyone know how to disable temporarily on hold, the defragmentation process can be completed successfully.

  Published by: Admin on December 1st, 2007 08:13

  Hello

  to disable the standby/Hibernation mode on your system, you should just go to "Control Panel" and open 'powersaver' to change settings powersaver.

  The Powersaver contains profiles where powersaving all associates are defined parameters. You can change this profile and disable the sleep/hibernation mode to perform your defragmentation.

  It would help if you post what system you have...

  Greetings

• Running back from standby/hibernation program

  Hey there,
  I want to launch a program every time I come back/sign my computer after the standby/hibernation mode. I only found a possibility to play sounds of a logon each time that this happens, but I can't run programs like that. Is it possible to do it on Vista?

  PS: If it isn't, can you send this request apparently simple functionality to the Windows 7 development team?

  While the mark's instructions look as if they will work, there is a more elegant way to achieve, using Vista built in Task Scheduler.

  To create a task that runs whenever you unlock your profile:
  1 open the Task Scheduler [start > Panel > system and Maintenance > administrative tools > Task Scheduler (or just type "Task Scheduler" in the box start search)]. You will need an administrator account/password for access to this.
  2. Select "Create a task" to create a new task.
  3. a panel with several tabs will open.
  4. fill the 'Général' tab to meet your needs.
  5. go to the "Triggers" tab and choose "new". Another panel will open. At the top of this Panel, you will see a (see below). Open it and choose ' to unlock the workstation. Then choose if you want this task to run just for your profile or for everyone. Click on 'ok '. (You can find it useful to use the option "Delay task" to delay the task for 15-30 seconds to give your office a chance to load before the program runs.)
   
  6. go to the Actions tab, select 'New', choose 'Run program' and locate the program you want to run.
  7. Select the tabs 'Conditions' & 'Settings', respectively and change various settings according to your needs. (Make sure that the "Run on AC Only" option is disabled if you are using a laptop and want the task to run when it is unplugged).
  8. click OK to save your new task.
  Now, whenever you unlock your profile after the standby or Hibernate mode, your program runs.
  If you follow these instructions, but choose "connection to" rather than "To unlock the workstation", your task will run whenever you connect (unlock and logon are not the same thing as the computer is concerned, so keep that in mind).
  This may not work if your profile is not protected by a password, but all mine, so I couldn't test it in this situation.
  I hope this will satisfy your needs.
  Best wishes
  BookwormDragon

• Satellite Pro U300 (PSU31E) standby & hibernation fails after updating BIOS

  Hello

  I wonder if it is common that after the upgrade of the Satellite Pro U300 (PSU31E) of the BIOS 2.50 at BIOS 3, 70 - Win or 3, 90 - Win, do sleep modes and Hibernate the * completely locked laptop computer? *

  After the upgrade, when I try to enter sleep or hibernation, the laptop turns off the LCD and gets locked so it isn't help to press and hold the power button, open/close the cover, press Fn - F3 or F4 - Fn, the only way is to disconnect the power supply and wait until the battery runs down, or simply be very rough and * disconnect the battery *.

  While the Pro U300 is locked, I hear that HARD drive and fans are also swivel - as soon they were when entering standby or hibernation mode. Very ugly behavior - you can FRY your laptop with something like that. I thought that BIOS 3.70 was faulty but unfortunatelly version 3.90 also worthless.

  Furthermore, I can't yet understand why large (70% of the zip file) file of the package to upgrade the BIOS (3.70 and 3.90)... is the portable other flashers log file?

  Your ad, I understand that the screen does not wake up after its entry in the standby or hibernation mode.
  Am I wrong?

  I noticed that Toshiba has released a new version of the Intel graphics driver.
  At this time the update is 02/20/08 and the version is 6.14.10.4831.

  Maybe you should try to update the display driver too check to see if it would help to get rid of this annoying display problem

  I recommend to remove the old version of the graphics driver first, then install the new downloaded driver.

  Mate good luck

• Keys get stuck on the Satellite A60 - 142

  Hello all, I hope someone can help me here.
  Currently I; m using my laptop frequently, I write a thesis.
  I have problems with my keyboard: some keys stuck after working for a while, it is never from the beginning. The keys that get stuck caps lock, shift, and CTRL keys, very irritating when you type a text. Restart is not enough, when I do that some letter keys do not work. The laptop must be turned on during some time to make it work properly again. Anyone have experience with this problem and knows how to solve?

  Thanks, has soon B.T., Amsterdam, Holland

  Hello

  What do you mean exactly? The essential mechanism or the key issue of software?
  If you mean the key mechanism then I recommend to remove the CAP from the keyboard and then you can try to clean the key spot. Perhaps a dirt and grime could have a negative influence on the use of the key.

  But if it is a software problem if the cleaning process will not help.
  Sometimes cable keyboard could have a bad influence on the function of the keyboard.
  Have you tried to reinstall the OS? I think you should check if the new installation of the OS could solve this problem.

• TX2-1020us digitizer cursor gets stuck 1cmx1cm of the upper left corner

  I have a tx2-1020us

  Sometimes, the stylus cursor takes over and gets stuck about 1cmx1cm from the upper left corner of the screen if the screen is 90 degrees or to move away it from the keyboard when you use it as a laptop. If less than 90 degrees, when this happens, it's somewhat usable but the slider still jumps at the skylight at random.

  I've known as a locking of the keyboard once but removing the power and the battery it is resolved.

  To troubleshoot, I ran the HP and N-trig utilities and they found no problem so even the question that happens. I downloaded the latest drivers from this site and install, I searched on Google and Asus seems to have a similar problem but I don't know if this applies. Sometimes, when I reboot it goes far, other times it is not. Deactivation of the first N-Trig driver stop the question but then of course, do not work the key features.

  I installed the software (for most, MS Office, Corel PSP and NeatWorks) and installed a scanner NeatWorks and GPS MS on it since I bought it last Friday (not connected when it is the case).

  Has anyone else seen this, they are of a resolution, I would stay before 15 days runs out?

  Problem solved!
  
  Turns, I have a desk lamp fluorescent light about 15 cm from the laptop.
  
  When the lamp is on and the laptop is plugged in, it does the cursor thing erased. Unplug the laptop or move the lamp 25cm and everything works perfectly. Go figure.