lose the usb port when restarting

Similar Questions

• Interruption of the USB connection when restarting a computer

  When the computer restarts, two USB DAQ devices are not visible in LV or MAX.

  To get these devices (USB-6210 and cDAQ 9211 with single chassis USB) for you sign up, I need to disconnect and reconnect the.

  Is there a way to get the LV to see devices without physically breaking and the USB connection?

  Carmen,

  It is a problem that we have seen previously, mainly when the OS loads, all the material is detected. In some cases USB devices are detected, but the BONE did not complete its driver loading process, causing a race condition. You are able to recover only when supply you either cycle the USB device or disconnect and reconnect the device.

  I had read the following article which explains how to force windows to delete and detect a USB device.

  http://digital.NI.com/public.nsf/allkb/1D120A90884C25AF862573A700602459

  Then I would create a batch file that runs each time the computer starts.

• BlackBerry Smartphones Pls help me my 9860 touch hangs when boot nd the system does not recognize the usb port when it freezes on startup

  Recently, my 9860 touch starts not finished... It stops at halfway when startup nd freeze... 2ndly starting my system recognizes usb d port, but when it comes to where it stops booting, the system doesn't see it me collapses more so to reload the software

  Hello Dtobs007

  Welcome to the community

  I recommend you try first method Mode without failure. Article ID: KB17877 How to start a mode BlackBerry smartphone without failure.

  Another thread explains how to fix this problem, for your reference.

  By JSanders. http://supportforums.BlackBerry.com/T5/BlackBerry-torch/BlackBerry-torch-9860/TD-p/2597381

  See you soon and good luck.

• Using the usb port causes my computer to restart

  When I plug anything into a USB my computer to restart trys, it does not restart correctly until I have remove the item from the usb port.  I have a printer plugged into a USB at the back of the computer and that works fine, but if I try something else in the same port, even just a stick of memory, he knocked out the computer!  Any help appreciated.

  Hello kaydee16,

  I would say confirming that you are up-to-date with the latest firmware, drivers, and updates to the BIOS of your manufacturers Web site.

  How long have you encountered this problem?

  Did you of recent changes made to your system, before having this problem?  (installation/uninstallation software/hardware)

  What version of Windows XP and SP are you currently using?

  What anti-virus software are you currently running and when you ran a full scan last?

  Please let us know status.

  Thank you

  James

• How can you stop safely remove hardware to appear when there is nothing connected to the USB ports?

  Orifginal title: Aggrevation

  How can you stop safely remove hardware to appear when there is nothing connected to the USB ports? It is causing my screen lock and give an error does not.

  Hi ElginCarelock,

  You can try to restart the computer and check.

  Uninstall all USB device manager entries

  a. Click Start and typedevmgmt.msc and press ENTER.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer and check.

  Hope this information is useful.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error "Windows has stopped this device because it has reported problems. (Code 43) "when I try to plug my mouse optical usb into the USB port.

  Original title:

  First here is my card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02479651&cc=ca&dlc=en&lang=en&lc=en&product=4299342 desktop pc
  and my mobo card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02560084&tmp_task=prodinfoCategory&cc=ca&dlc=en&lang=en&lc=en&product=4299342
  (running windows 7 x 64 and not changed all my pc hardware so everything on the Web page is true)

  in any case, when I try to plug my mouse optical usb in the port of e/s (usb port) on the front panel (which supports usb 2.0) a notification pops up saying
  "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it. Help to solve this problem, click this message. "
  so I click it and and called up pop-up windows
  "the usb device not recognize."
  display 1 unknown device. Link to the image: http://img38.imageshack.us/img38/3579/usbdevicenotrecognizewi.jpg
  Then I double click on it, next pop up another window called "unknown device properties" and under "device status", he said:
  "Windows has stopped this device because it has reported problems. (Code 43) »
  Link to the image: http://img204.imageshack.us/img204/8597/unknowndeviceproperties.jpg

  Also the same things happen when I plug in usb, keyboard , but not when I plug a flashdrive usb 2.0 without notification or anything pop up.

  Here's what I'm trying to fix it but ended up with saying it was installing the device, installation failed and getting the error failed and unrecognized again...

  • Plug my optical mouse on my other ports and it works perfectly fine (to see if its working)
  • Plug the mouse (in the wrong port), went to Device Manager and uninstall the unknown device, reboot with usb plug in and have the connection to the internet (not decided)
  • Uninstall all devices under USB bus controllers in the Manager device and rebooted with mouse in internet connection (not decided)
  • Went to device manager expanded bus controllers USB right-click on power management all the device label "usb root hub" click and uncheck the box "allow the computer to turn off this device to save power" and reboot (do not set)
  • Open the normal startup in msconfig (system configuration) selected and restarted (did not set)
  • Shut down the computer, disconnect the plug, unplug all the devices connected to all IO ports (usb port specifically) and my desktop pc has left alone for an hour and a half and start it to the top after with everything back plug (mouse in the wrong port) (has not set)

  Note: when the mouse is connected to the usb port it is light on substance, but its does not (not flashing do not and when you move, mouse is frozen on the monitor)

  Hello

  The results highlight the drivers. It is best you contact HP support and get all the latest device drivers.

  http://WWW8.HP.com/ca/en/support-drivers.html

• Satellite Pro M70 freezes everytime when the USB port is used

  Satellite Pro M70 (SPM76) crashes every time when the USB port is used.
  The mouse works, but external HD/Extarnal card sound/Memory stick causing the laptop to freeze. All the drivers are installed right, they are the most recent and have no trouble with other users.

  The devices are all compatible. Service pack 2 is installed, and all the hardware drivers on the toshiba have been updated... again, same problem.
  The toshiba is about 2 months old and have had this problem since I got it. First I thought it was the drvers, but I cleared of all (?) other options but the USB ports.

  Hello

  Believe me, that's not easy to say what the problem may be. It is important to see if the problem occurs because of hardware or software may be. I recommend you to backup all your data and reinstall the unit using rescue media. On this way the unit will be factory settings and will be clean preinstalled. Test your USB devices and see what happens.

  Try to use some standard like USB stick or external HARD disk parts, because in this case, you must not install any drivers please. If you use other devices like USB webcam with own software and drivers, it is possible that something goes wrong, but what. On this path, it is not possible to say.

• Satellite M30X powers off the power when you touch the USB port

  Hello everyone, just registered and it is the first problem:
  As there is no general hardware forum, I post my problem here.

  I got it twice, my laptop
  (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

  Motherboard:

  NorthBridge: Intel i855GME
  SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
  Motherboard model: Toshiba EAL20

  USB:

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
  Version: 1.0
  Interface: UHCI
  Frequency: 48 MHz

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
  Version: 2.0
  Interface: EHCI

  I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

  Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
  There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

  Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
  I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
  Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

  What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
  Still works well. Now for me, that I broke the USB port Insider somehing.
  I could not determine also the loose parts or unfirm at all.

  Y at - it there, diagnostic software that measures the motto of the port or power problems?
  I have a multimeter, fetch short-circuits with it?

  I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

  Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

  Fabian

  Hello

  I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

  > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

  I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

  However, what we can do is to provide some suggestions and assumptions
  It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

• Portege M500 cannot start when the USB ports are loaded

  We have a M500 that recently seems to be affected by start-up problems when the USB ports are loaded with things like KB and Wireless Mouse USB external adapter.

  When these ports are occupied at the start, all the usual tools seem do not load and the associated icons do not appear in the toolbar at the bottom of the screen. The machine in question XP Professional and has 2 GB of RAM. The machine software is generally updated. Machine seems to start normally when the USB ports are empty.

  Once completed a successful boot USB ports can be occupied and the machine will then seem to operate normally.

  Any thoughts?

  Thank you.

  Hello!

  In your case, I would do a BIOS update and also the chipset driver.
  The two you can find on the Toshiba site. I m not sure but I think you have a model for Canada:
  http://www.Toshiba.ca

  Have you tested the devices USB on another computer laptop or PC? Maybe the problem is the keyboard and/or the mouse and not the laptop.

  Good bye

• 700 - 060ea Office: stop the usb ports go to sleep when the rest of the PC

  When I get my laptop connected via usb, the system constantly charge the phone when the pc is asleep. Have you tried to uncheck "allow the computer to turn off this device to save power" in the Control Panel/Device Manager/USB controllers/Properties tab, but the ports still off. I saw my present mobile on this hub have obtained the correct material. I would have preferred that the PC continues to sleep when it is inactive, but want the mobile to continue loading.

  Should I change something in the BIOS maybe? If so, how can I access BIOS for this model?

  Thank you in advance.

  Hello @tomsy,

  I read your post on how the USB ports on your computer constantly power when the rest of your system enters mode 'sleep', and you need to avoid this. I'd be happy to help you in this case!

  In order to maintain your USB ports power while your computer sleeps, your office should be equipped with a High Powered USB port. It also allows to load when your office is completely turned off.

  According to the Specifications of the product from your desktop, High Powered USB is not available on your system.

  I hope this helps!

  Best regards

• due to lack of space on my HARD drive, I moved Photoslibrary to a USB port. When I connect my iPhone 6 I am able to transfer photos from my phone to the PhotosLibrary on the USB port, but when I sync, photo library is not get highlighted. Cannot synchroni

  due to lack of space on my HARD drive, I moved Photoslibrary to a USB port. When I connect my iPhone 6 I am able to transfer photos from my phone to the PhotosLibrary on the USB port, but when I sync, photo library is not get highlighted on the USB port. Cannot synchronize.

  Hello, manoj0910.

  Please visit Apple support communities.

  Looks like you can't synchronize the pictures located on your external drive.  I need a little more information about your configuration to provide a better answer.  However, we will try to sync your photos through the section of the file through the article below.  You just need to direct iTunes to where your photos are stored on your external drive.

  If your photos are in a folder

  1. Select "Choose a folder" from the context menu.
  2. Choose the folder where you store your photos.
     
  3. Click on apply.

  You can arrange photos in subfolders to create photo albums.

  Sync photos from your computer to your device iOS through iTunes

  See you soon

• When I plug my Galaxy s captivate phone into the usb port on my computer, it will charge the phone but will not allow sharing of information from computer phone.

  Original title: usb with smart phone problem

  When I plug my galaxy s captivate phone into the usb port on my computer, it will charge the phone but I cannot share the news from computer to phone. In fact when I click on the computer icon, it shows the dvd, floppy disks and hard disk but not the phone. I use a mouse usb and headphones and they work fine. I tried to search for devices and it does not work. I run Defender pro anti-virus software and have checked the firewall, but I don't see that his block the phone. I don't know what else to do. Help, please. Thank you

  Hi Mike,.

  Just to follow up with you on that, that very well may be the cause. Especially when it comes to mobile phones, the real cable you use is very important to have all the features when it is plugged into a computer. Where you can try a new USB cable yet, I hope that whoever is completely compatible with this phone.

• VN7 - 791G: Wifi slow and unreliable when a USB drive is plugged into the USB ports on the right.

  WiFi becomes quick and reliable whne the memory stick is disconnected. Always reproducible. Does not occur when the memory stick is plugged into the USB port on the left. Also has anyone seen this behavior?

  Wireless network adapter Qualcom Atheros QCA61x4 with the version of the driver 12.0.0.230 dated 03-2016-21.

  Thank you

  Chris

  Hello

  The explanation is simple. I'm sure that the memory stick is a USB 3.0, a plugged in a USB 3.0 port. The problem is that all USB 3.0 devices generate a 2.4 Ghz interference, as it generates interference on the frequency working on wireless. The solution is to connect the player to another port or to spend the 5 GHz wifi if your router supports. The wifi antenna is probably very close to the port and to the USB key.

  This is known for a long time, and has nothing to do with the laptop.

  There is an article on the Web page of intel who described the problem more technically. You can search if you wish.

  This causes a problem also with a wireless mouse, if the receiver is connected next to a USB 3.0 stick or any other device.

• For some reason any, that my printer has enough work and when I plug in my camera to download images, the computer says it does not recognize the USB port, which could be the pronblem?

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  When did this problem start? What did you change shortly before it all began?

  Please quote the exact text of the message you get, verbatim.