Loss of internet connection - occurs randomly when using the Internet

I can surf the Web for a few minutes or hours and out of nowhere, I'll be unable to connect to the internet. I tried with Firefox and Internet Explorer. The computer always says that it has internet connection but the pages may not load. To solve the problem together, that I have to do is restart my computer.

Can I have a virus? Is there a simple way to solve this?

Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.

Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

Troubleshoot network adapter problems to Microsoft link above.

Try without commitment TCP/IPv6:

If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

See you soon

Mick Murphy - Microsoft partner

Tags: Windows

Similar Questions

  • I6 fire babysit device when using the internet? any solution?

    I6 fire babysit device when using the internet? any solution?

    Let's define "overheating". If the temperature of the phone reached a dangerous level the phone turns off it to cool down. This phenomenon occur? If this is not the case it is not overheated.

    What is your cell signal? If the signal is low, the phone must increase its power to maintain a connection. This may require as much as 10 times the energy as a strong signal, and the phone gets hot under these conditions. If will also drain the battery very quickly.

  • I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

    I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

    Ihab El-Sayed

    published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

  • When using the docking station when my laptop can connect USB. printer, etc... ? I know that I can connect my laptop to a docking station.

    When using the docking station when my laptop can connect USB. printer, etc... ? I know that I can connect my laptop to a docking station.

    When using the docking station when my laptop can connect USB. printer, etc... ? I know that I can connect my laptop to a docking station.

    Hello

    With Docking Station, you can connect all the cables for printer, keyboard and mouse, adapter directly to the charging station.

    So whenever you use a laptop, you have just dock the laptop on the docking station and not need to re connect all cables again.

    This will help you when you move frequently with the laptop.

    Docking station will save your time, outside any other aspect, that it has to offer.

    Zaki.

  • When you try to connect to my router using the IP address, he continues to ask for a password of windows security.

    When you try to connect to my router using the IP address, he continues to ask for a password of windows security.  I don't know what it is, I tried recording with every combination I can think.  Can anyone help?

    If you do not know the password of the router, then chances are good that you will need to reset it to the factory settings. Google your model and you should be able to find the instructions.

    I hope this helps.

  • Photoshop CC hang randomly when using any type of brush. (Please HELP!)

    Photoshop CC hang randomly when using any type of brush. I use Mac OS Mavericks and lates of Photoshop CC version, the only way to make it work is to switch to another application, and vice versa, but sometimes this does not work and I lose all information.

    I tried to reinstall several times Maverick and Photoshop, but it does not help.

    Does anyone have the same problem?

    Hello

    We believe that we have found a fix for this problem. Please see the 'Correct' (#348) post in this thread about where to take the plug-in:

    http://forums.Adobe.com/thread/1012373

    Kind regards

    Steve

  • Satellite A200 - IE7 windows 'restore down' when using the Tracker pad

    Hi, I recently bought a Satellite A200 - 1VO and when using the laptop without a windows mouse explore 'restore down' at random.

    I found a thread on the site of the Internet USER who said that if his past not with a mouse, it may need tracker drivers up-to-date.
    You can also consider its under warranty.
    Any ideas anyone?

    Hello

    It s a bit confused what you´ve writes down. What do you mean exactly, where´s the problem and what you want to tell us when writing:

    > and when using the laptop without a windows mouse explore 'restore down' at random.
    >
    > I found a thread on the site of the Internet USER who said that if his past not with a mouse, it may need tracker drivers up-to-date.

    Whereas it should be, where´s now the problem?

    Please give clear and understandable feedback, then I and other users you could point to the solution.

    THX

  • Vista, a pppoe connection is created by using the 'Get Connected wizard' or rasphone.exe, she appears as a "Dial-up connection" in the network connections folder.

    Vista, a pppoe connection is created by using the 'Get Connected wizard' or rasphone.exe, she appears as a "Dial-up connection" in the network connections folder. When you right click on the connection of customer created, click Properties, it says "connect using the Modem.

    Is it a registry problem or what? How can I fix?

    original title: PPPOE connection problem

    Hello

    1. you connect using a cable or DSL modem?

    2. did you ever get this working before that?

    3. are you connected to a domain?

    4 are you running Vista in a virtual environment?

    You doing appeared in this link to create the PPPOE connection:

    http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-PPPoE-connection-to-the-Internet

    Thank you

  • Single line vertical when using the ADF to Scan or copy on HP Officejet Pro 8600

    Printer HP Officejet Pro 8600 Premium (CN577A)

    OS: MS 7 64-bit

    When you use the ADF for my printer HP CN577A Officejet Pro 8600 Premium, I get a single vertical line on the document which is produced. This occurs when copying or scanning, both black and white and in color. If I scan or copy using the glass, I do not get the vertical line.

    I already tried troubleshooting.  I unplugged the printer, left without electricity for several minutes; that didn't fix the problem.  Then, I cleaned the rollers and glass; I always get the vertical line, but only when using the ADF.

    My firmware version is up to date (CLP1CN1150CR).

    What should I check next?

    The only difference between the ADF and scanning flat, from a point of view of the scanner is there on the glass, it happens.  I suggest you get a bright flashlight and examine the corresponsing area hence is the line, it's almost certainly a spot on the strip of thin glass which is being just in the right place.

    I've seen some people suggest that put a flashlight almost parallel to the Strip, it shines from the bottom can highlight the area problem.

  • HP b209a printer range will not connect to router comcast using the WPS button

    HP b209a printer range will not connect to router comcast using the WPS button. I try to use a new Comcast router (technicolor TC8305C). When I try to connect the printer times out and says that no connections are when I check for wireless connections. Yet, when I print the network configuration page, the SSID for the new router is at the top of the list. I reinstalled the software by the support of Comcast, but it did not help.  I'm ideas please help!

    Thank you

    Never use WPS to connect.  If done it should be disabled in the router for security reasons.  Connect manually via the SSID and password following the instructions in the manual.

  • OfficeJet pro 8600 print a single vertical black line when using the charger

    OfficeJet pro 8600 print a single vertical black line when using the charger

    Hi @realestatejeann,

    I see that you have found one black vertical line when using the ADF. With a few steps, we should be able to solve this problem.

    Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

    Here is a document for the cleaning of the glass Strip and the underside of the scanner cover.

    Vertical stripes, lines or streaks on Copies, faxes or scans.

    If you need help, let me know.

    Good day!
    Thank you.

  • I a s 6 more and when using the phone, if my face touches the screen it clicks on the logout button and the phone hangs up the call. Is it possible to prevent this without holding the phone away from my face when calling?

    I a s 6 more and when using the phone, if my face touches the screen it clicks on the logout button and the phone hangs up the call. Is it possible to prevent this without holding the phone away from my face when calling?

    iPhones have a proximity sensor which is supposed to automatically turn off the screen when you hold it in your face. If this is not the case you can take the phone and have it checked.

  • OfficeJet Pro 8600: Officejet Pro 8600 leaves black lines on docs scanned when using the document feeder

    This is the second HP Officejet Pro 8600 I had - one was replaced by HP, after that the same issue arose.  I tried to clean the entire unit, but we still get a thin black line running vertically down the page.  This line is divided into sections of 1 "and 2.5" in length.  Sometimes I get the fine line and then almost a shadow line that is parallel.

    Any suggestions would be very appreciated I have scan documents to PDF format and it's hassle to put everyone on the flat for scanning.  I use the charger of the doc on a daily basis and wonder if this could have something to do with the lines.

    Thanks for any help.

    The question is a spec on thin (~ 1 "wide) glass to the left of the main bed scanner.  Clean this area as described in this document.  It can be difficult to see the affected area, a bright flashlight which is held at an angle to the glass can help find the place.  Even a very small spec on the glass can cause a black line when using the ADF.

  • Error message indicating the r300 display driver stopped responding when using the full screen.

    Original title: driver atikmdag error message when using the full screen.

    Error message indicating the display driver r300 unresponsive, but has recovered, usually when enter full screen mode.

    Hi Peterrichardson,

    1. when exactly you get this message?

    2. what player do you use?

    3. you remember to make changes to the computer before this problem?

    Method 1:

    You can try to reduce the hardware acceleration and check.

    a. click the Start button, Control Panel.

    b. now, select appearance and personalization, and under display, select adjust screen resolution.

    c. now, select adjust the resolution.

    d. click Advanced settings.

    e. now, click the Troubleshooting tab, and select the change settings button.

    f. in the Security dialog box, click on continue.

    g. move the hardware acceleration slider to the third notch.

    h. click OK and restart Windows.

     

    Method 2: Update your display driver

    Updated a hardware driver that is not working properly

    Hope this information is useful.

  • disable the touchpad when using the mouse?

    How to disable the touchpad when using the mouse?

    Hello

    Please contact Microsoft Community.

    Most laptops have a function key (FN) which can be used in combination with other keys for example FN + F2 or FN + F7 to disable or enable the touchpad.

    You can also disable the touchpad in Device Manager.

    To disable the touchpad in Device Manager, follow these steps:

    1. Click Start.
    2. In the start search box type devmgmt.msc, and then on enter.
    3. In Device Manager, expand mice and other pointing devices and locate the touchpad.
    4. Right click on the touchpad and click on the disable option.

    Following the steps above should help you disable the touchpad.

Maybe you are looking for