Low frequency

Hai guyz,

I developed a code to save the data while the cDAQ is read. The amount of the fine when I set to 1 Hz with the recording of the data showing the data taken every 1 sec interva. But when I tried to make it to 0.017 Hz displays error codes. The reason why I did was I thought he would make the program to read data all the 1 minute and save it. Maybe it's the wrong approach. If so you would show me how to do common sense? I have attached a screenshot of code and example of recorded data.

Kind regards
Newbie92

What error do you get?  I'm guessing a time-out error.  The simple solution here would be the use of use of a Structure of the event with a time-out of 60, 000ms.  In the case of the time-out period, you do your reading and treatment.  But it would also add you abandonment and/or stop button event case law to allow the loop to stop without waiting 60 seconds.

Tags: NI Hardware

Similar Questions

  • Memory running at a lower frequency

    I recently added 1 GB 667 DDR2 ram to my office, a1514in Pavilion (previously 1 GB 667 stick). But now the bios is show my DRAM frequency as 266 MHz (PC2-4200), these are the cases with different configs:

    -If I put only OLD stick of 1 GB 333 MHz (PC2-5300) show

    -If I put only NEW stick of 1 GB it will show 266 MHz (PC2-4200)

    -If I put both OLD & NEW 1 GB stick will show at 266 MHz (PC2-4200)

    Has also tried different machines slot but no use (I have only 2 slots and memory support for my system max is 2GB BIOS version 3.24)

    I am not able to understand what the problem is. In CPU - Z under the SPD, the two sticks are showing similar settings (I have not so good idea on these parameters). Please help me why the new RAM runs at a lower frequency... What should I do?

    Hello Khot

    What is the model of your Samsung of RAM stick?

    According to the specifications of your motherboard RAM supported, speed isn't PC2-4200 and PC2-5300.

    Another thing, usually by mixing different RAM is a bad idea. The reasoning is that each RAM stick is intended to be run at a specific frequency, timings and voltage. If two sticks use different frequencies, timings, tensions that the BIOS will be all run the highest common denominator. In your case, that your new stick of RAM PC2-4200 and, therefore, the BIOS reads your second stick is run at the same speed for stability purposes.

  • Satellite A215-S7444 - name of the low frequency amplifier

    I need to know the name of aplifier of low frequency in a Toshiba Satellite A215-S7444 main laptop Board. I have problem with my speakers because they beep. And the problem is with amplifier speakers.

    Please tell me the name of this integrated circuit.

    Hello

    I think that no one here can answer this question because it s only a user to user forum and I have never seen anyone from Toshiba here. I think that this question can be answered only authorized individuals.

    I recommend you contact an authorized service provider. Technicians could answer this question and help you get a new spare part.

    Good luck!

  • low frequency with labview 2010 auto and agilent 35670a

    Hello

    I work on the automation of low-frequency measure a 35670A Agilent. I currently did a program that allows a measurement with an average of FFt given a frequency bandwidth and frequenct from beginning, see picture attached, but I try to measurement of spectrum using this power VI ( ), but unfortunately I can't seem to find how to convert a signal from my block diagram below in order to send the input signal power VI above spectrum X no indication or help will be appreciated.


  • NEITHER USB-6343: erratic low frequency 1 counter measures

    Dear members,

    I'm looking for help with a measure of low frequency counter.  I tried to make it work for a week or two, but I keep getting erratic measures.  It will read the rpm properly for a second or two and then it will give a ridiculous value on the order of 10,000 times the correct value. I can not get a constant value.

    I use a DAQ series X NI USB-6343 multifunction with Geartooth Honeywell GTN1A111 sensor. I enclose a sketch of the wiring configuration.  I think that it is correct.  Sensor output to the door of the meter.

    To try to solve this problem, I hooked the sensor to an analog input channel to make sure that I was getting a TTL signal by sensor.  I noticed every once in a while I'd see a glitch of little noise in the signal and I guess that's what is causing my problem with the meter.  I inserted two waveforms of the sensor signal (one with the clean signal) and the other with the glitch of noise.  My understanding of a TTL signal meter channel will examine LO voltage when it is below 0.8V and HI when it is larger than 3.8V.  So I really do not understand why these little glitches could be the cause of the problem because they are well below and above 0.8V and 3.8V, respectively.  I think that the noise comes from a frequency converter used to drive the engine.  I tried the system as much as possible of the Earth.

    I guess I'm looking for another approach.  I could potentially use a digital filter to help with noise? The glitch is in fact the problem or I forgot something.  The VI in question is attached.

    Thanks in advance,

    Mike

    Have you tried to set up a digital filter yet?  Obviously the seeds are collected as an additional transition (the method of low frequency counter 1 measure the period and then reverse, so a short glitch would record as a very high frequency).

    You can enable the digital filter with the following property node:

    Min pulse width is guaranteed pulse past the filter, so it should be low enough for the real signal is guaranteed to pass through (but high enough so that the glitch is always rejected).

    Best regards

  • static/digital waveform output and low frequency measurement of voltage - SMU-6358

    Hello

    1. I have an attached VI [digital_voltage_output] who must generate a logical true or false static state in the output of the device/port0/line1 Word to say. When the VI works I click the button several times, but nothing happens to the port0/lines1.

    2 such a thing [digital_voltage_waveform_output_square] if I'm trying to generate a digital waveform to pin the same with the waveform generating VI. If I connect a waveform chart to the output of the generator function VI, then the chart will show me the good waveform I want, but still nothing is written to the text file.

    3. I have read the manual for the X series cards, but it remains unclear for me a little how to things of the road in LV I have a measure of the frequency measurement VI low frequency that I downloaded. It offers me the ports for the supply frequency - ctr0, 1, 2, etc. As far as I'm concerned the PFI ports are responsible for these types of actions. How can I find out the LV that I want to connect say ctr0 and pfi0? »

    I use LV 8.6.

    Thank you

    Kriváň

    Hi Kriváň,

    The problem you had with the choice of a specific digital line as a physical channel, is that the control that was previously used in this example was created for a data acquisition task that uses a whole port rather than a specific line. I was able to overcome this problem by removing the control and recreate. The control now gives you the option to choose the specific digital lines e.g. port0/PXI1Slot2/$line0.

    I was also able to overcome the error of-200802 you mentioned. I was able to do this in a real constant of wiring at the entrance to auto-start the VI DAQmx writing then remove the DAQmx beginning the subsequent code VI. The modified code is attached.

    I hope this helps.

    Best regards

    Christian Hartshorne

    NIUK

  • Measure voltage low frequency

    Hello

    I use PCI 6025E to control load Bank and to measure the voltage, current and frequency of a generator.
    Current and the frequency is not a problem, voltage is toublesome.
    As on test bench already there are few PCI cards and large number of sensors, I don't want to add NI 9205 or any other additional maps and the size of the area (other people are also working there).

    The problem with blood pressure is three two generators spend 400 rpm to 1600 rpm is. some 15 to 55 Hz.

    I got two solutions for this:

    1, put a step down transformer (230 Vac / 5 Vac) and then measure the voltage. But I have to deal with magnetic saturation with commercially available processor during the test to something like 15 Hz. I don't want to take the pain to built my own transformer.

    2, using high precision voltage divider. The problem is that what should be the galvanic insulation? Insulation transformer, but still low frequency problem.

    Where could someone suggest me because there is a bit of confusion in my head.

    Thank you.

    If you have a sinusoidal generator (15 Hz migth be hard for the soundcard ) you can do a calibration of your transformer.

    (If only the amplitude of the voltage is of interest, use a DMM isolated as a reference and run your generators)

    Or you buy an insulation voltage amplifier. (weidmueller, phoenix, wago,...)

  • Can I use 6115 measure DC or low frequency signal

    I use 6115 OR data acquisition if put singnal superior to 100 Hz, the result is very good.

    But if the frequency below 10 Hz, the result is not fair.

    I try MAE and choose the DC coupling mode, it still can not measure DC signal.

    What can I do? or the NI6115 can measure just the DC or the lower frequency signal.

    Thank you

    Hi xsfl,

    Please try the other channel. I wanted to ask, what are the characteristics of your signal? What is a sinusoidal signal, how often, what range of amplitude? Also, have you been able to measure low frequency signals before or is this the first time you try?

    Also, remember that you are above the minimum rate, 20kS/sec, sampling sampling as to the care.

  • Low-frequency shaking sound when the backlight is disabled

    Very starnge.  It only happens for some MP3 song, and when the backlight turns off, I hear that very clearly some low-frequency (about 3-4 Hz) sound poping out.  Once I press a button and the backlight was on, pop vanish.

    Yes, after changing the EQ for 'Rock' to 'Normal', the problem is resolved.  I don't even have to use "custom" for the equalizer.  This problem makes me very carefully listern for the background music/noise.

  • Meter very low frequency using PCI-MIO-16-4

    Hello

    I am trying to use a card PCI-MIO-16-4 with BNC-2090 to CI FREQ. Because the sometimes less than 1 Hz frequency of our leaders, or even no time measurement taken, the vi program always shows "Error-200527" and tells me that the min frequency must be greater than 1,192 Hz. If this card cannot measure very low (even zero) frequency in time measurement taken? If it is possible, how? Could you show me some examples? Thank you very much.

    Damien

    What method of measure do you use to measure your rate?  You are able to assign at least 0 (default) to 2 that would be the rounded version of 1,192.  Alternatively, you can try to use one of the other methods to measure and see if that helps.  All these values can be set with the channel to create VI.

  • Analysis of low frequency - great obstacle, easy solution

    I'm trying to analyze a signal between 0-2 Hz. The signal is a clean sine curve where the amplitude and frequency changes.

    I wanted to use the ExpressVI which is called "Your measurement" as I am not that experienced with Labview.

    I used a signal generator to simulate, and it seems that it works very well for signals above 10 Hz. lower than that returns the high frequencies and amplitudes of false.

    Please help me out here. The signal I'm generating is sampled at 100 Hz, with n = 10.

    Well, I sort of figured it out by reading my own question. Increase the number of samples done...

  • HP pavilion touchsmart 14: Audio works, but now the low frequencies or lower

    Hi, Ive had this laptop for a while now and a few months ago, that the audio was working fine when I was producing my music, I plugged my microphone, guitar wheel, I even put in place a new maschine micro mk2 and he worked well with low latency. I'm not changing the latency and a few weeks after leaving my computer sit, I'm back and tried to go on soundcloud and audio did not work well. The audio was released, but it was as if the bass had been manually disabled. I have preveously owned a macbook so if you could please clarify and explain how to solve the problem or what is happening, that would be greatly appreciated.

    Hey there @basssgod,

    Welcome to the HP support community where you can ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP's Support and wanted to reach out and help with the sound issue that you are experiencing. If you perform these troubleshooting steps, it can help you recover the sound quality.

    Please note: remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

    Here is a document titled No. sound from speakers. I know that you can hear sound from your speakers, but you mentioned that the bass sounds as it disappeared. I have provided this document for you because there are steps that can help you to get the sound working properly troubleshooting.

    Are - what you happened to try the audio Troubleshooter? It might be able to solve your problem automatically.

    This is another step to try.

    1. right click the speaker icon in the lower right corner of your time.
    2. click on playback devices.
    3. click on speakers/headphones.
    4. click on properties.
    5. click on the Advanced tab in the Properties window (this also will give you subwoofer settings)
    6. change the default menu Format in the highest quality.
    7. apply properties.
    8. click OK to close the Properties window.
    9. click OK to close the playback devices.

    If none of these options is right for you, you can do a System Restore. System Restore helps you go back to a time when it worked correctly for you.

    You can use the HP Support Assistant's drivers. Here is a link to the HP Support Assistant, if you need it. Simply download and run the application and it will help with the software and drivers on your system that need updated for Windows 10.

    Please follow these troubleshooting steps, re-post and let me know how everything went. Also, could you please provide me with your model number (How can I find my model number or product number?).

    Thank you for your participation in the Forums of HP where we want to help you as well as others who may encounter a similar problem that you have. Please consider tagging the post in order to resolve your problem as "Accept as Solution" to help other members of the community! To show recognition for my efforts please click the Thumbs Up below

    Thank you!

    Have a great day!

  • Error-200141 with low frequency counter measures

    Hello

    I'm trying to measure the speed of a rotating shaft using a laser tacho Keyence and a counter on my PCI-6601 entry.

    I can't reach my vi, but I join a PNG of the section of code.

    Background:

    -L' tree turns to ~ 6000rom

    -The counter is updated frequency measure ona climbing on board.  There are 9 rising edges per revolution of the shaft.

    The problem:

    -If I put the vi to capture a small number of samples, it works very well.

    -If I put the vi to measure the samples more 200141 occurs error "data has been overwritten before it can be read by the system.

    -The number of samples, I can get without problem varies.  200 seems reliable enough.  Sometimes I can get 1200, sometimes 600, sometimes 150.

    -I would like to be able to get samples of ~ 2000.

    -If I try to get samples continuously, I encounter the same problem.

    If anyone can help with this problem it would be greatly appreciated.  This is something I continue to flow upward against but so far have been unable to rectify.  I'm sure I'm missing something, but I have no idea what.

    Thank you very much

    Martin

    version 8.2

  • FGEN 5402 Amplitude at low frequencies

    Hello

    Sorry, I don't know the right place...

    I work with the NOR-PXI-5402 FGEN.

    My measurement is 1000 Hz to 1 Hz. The amplitude of my example is 1V.

    The FGEN made 1000-15 Hz 1V. After 15 Hz amplitude will made to 700mV (10 Hz), 500mV (5 Hz) so on.

    Is this normal behavior?

    How can I set the voltage at 1V constantly?

    I work with Labview, by the way.

    Thank you!

    Turn off AC coupling on the scope. The cut of the 5105 is 12.

    http://www.NI.com/PDF/manuals/374403b.PDF#page=4

    Jason L

  • Yoga1 11 s Haswell (4310y) - sluggish UI? Low CPU frequency?

    I know that the series is supposed to be slower than the series U, but I feel like this thing is abnormally slow on my GF Yoga 11 s. Task Manager indicates it only making .58ghz while trying to load the Sims 3 (I know that this game has problems, but it hardly seems to run about as well--surprisingly slow loading times). The Task Manager is incorrect? I think that the CPU is supposed to be 1.5 ghz. I also felt a bit slow machine regarding the user interface. For example, right click could be a small delay with regard to the context menu. Y at - it a setting or driver I'm missing here?

    Are you running on battery or sector? The default power plan seems to keep the system locked to a low frequency battery-operated.

Maybe you are looking for

  • Portege M500 - how to create recovery DVDs?

    Hi there :) I bought Toshiba Portege M500. Anyone know how to create a CD/DVD of recovery on this model? I installed the "recovery CD creator" but - I just can't create it. The only thing that came on the screen is: Qosmio Player recovery CD. On the

  • How to insert a scatter diagram in MS word

    Does anyone know how to insert a diagram of dispersion in a MS word document?  I'm developing an application using c# and Measurement Studio and my request is a report in MS word.  I just need to add a diagram of dispersion in the same document. Than

  • CD no longer works after windows loading 8.1

    Hello.  After the upgrade to Windows 8.1 my CD stops working.  Load discs and it would turn, but nothing on the computer has welcomed the presence of a disc in the CD or even a CD-ROM drive. According to the instructions of Microsoft, I removed the d

  • While the loop helps... I think so

    All, I have a fairly simple VI who catches the units of measure (send an 'A') of a MARK-10 test bench and MARK-10 dynamometer. I am struggling with how, and where, I should place my While loop. I want VI to do this is if the units of measure are not

  • LaserJet CP1525nw #CE875A: Color LaserJet CP1525 paper jam.

    Although there is no paper jammed anywhere in the machine, it is blocked in an alert of "paper in the output tray jam." A series of clicks can be heard when the machine is started, until the jam alert lights. This noise is new. The printer is two or