LRT224 hickups: abandon the WAN connection?

Similar Questions

• RV082 abandons a WAN connection immediately after creation

  I have my 2nd WAN connection on the RV082 setup to connect via the static IP address for a T1 connection. When I connect the cable, reports the newspaper...

  «WAN connection is in place: 216.130.xxx.xxx...» "and 3 sec later reports"connection to the Wan is down. "

  Can I connect a computer directly to the T1 with the same static IP settings, and it connects without problems.

  I'm on firmware version v4.0.2.08 - tm.

  Any thoughts?

  Have you tried changing the WAN2 connection with the WAN 1 connection to see if it will stay connected? You use Load Balance?

  Also for the connection that may not be not connected trying to bump on the MTU to perhaps 1492 and see if that makes a difference.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• the WAN connection becomes too slow after you have configured the VPN (Site Site)

  Hello

  I have two branches connected via WAN (MPLS) connection using two 2921 routers.the connection is 2 M.

  I set up a VPN between these two sites, but after the connection has become very slow.

  y at - it something I can do to speed up the speed of connection.

  VPN proposals are:

  Proposals of the phase 1: 3DES, pre-shared,.

  Phase 2 proposals: esp-3des esp-sha-hmac

  I don't think that lower levels of security proposals will add a lot to the speed...

  Hi Marc,

  one thing you should definitely is a hardware encryption go if you do not already tht, it also reduces the load on your cpu

  You can try other things is play with mtu, according to your line mtu and what applications are mainly used. try setting the mtu of at least 60 odd bytes lower than the mtu and also sometimes server line recommended mtu settings like server many have obligation to mtu to 1300 or 1400, if that's not it can cause a lot of re transmissions, you can also try fragmentation before encryption

  http://www.Cisco.com/en/us/docs/interfaces_modules/services_modules/VSPA/configuration/guide/ivmvpnb.PDF

• Windows 7 occasionally abandons the wireless connection

  I have recently upgraded to Windows 7, but now I'm having a problem with my internet connection.  My wireless signal will intermittently from all five to four bars, and moments later displayed a yellow triangle with an exclamation mark inside.  At this point, the connection disappeared entirely, and I need to reboot to restore.  Not only that, but the computer turns off as normal, so I held down the power button to stop it.  I know that's not particularly good for my computer, but it pales in comparison to the boredom of an unreliable signal.  Sometimes the signal will last for a few hours at a time, but sometimes I have to restart less than five minutes after turning on my computer in the first place.  Also, when the signal falls this way my computer sometimes has extremely slow (so slow I can't even close the browser window) before freezing altogether.

  It seems that this problem is exacerbated when the connection is moving a lot of data... for instance, I recently bought the game Mass Effect on Steam, but when I try to download the connection almost immediately falls.  It's frustrating because I've already paid for the game and I like to be able to install and play.

  My wireless network adapter appears in the device like a Linksys RangePlus Wireless USB Network Adapter Manager.  The model number is WUSB100.  I tried updating the driver through the Device Manager, but he seems to think it's common.  I really want a solution to this problem.  Is not the first one I've had since the much-maligned Vista upgrade, which in fact never gave me problems.  I managed to fix the other on mine, but at this point, it's been almost a month since I upgraded and I'm tired of not having a reliable connection.  Thank you very much!

  http://support.Microsoft.com/kb/976972

  This fix has far less solved this problem for me so far

• is possible to configure the wan on Dell N3024 switch port

  Hello

  as I said in the topic. I got a new switch N3024 of Dell.  I worked in before cisco, but dell is new to me. I have a few question to ask: -.

  is that we can configure wan on that port?

  is - this switch supports the aggregation of the ISL?

  If Yes please share the switch manual

  Thanks in advance

  The WAN connection is made usually by creating a VLAN and assignment of an IP address in the same subnet as the device that it connects this VLAN.

  Example:

  Create VLAN 10

  database of # vlan

  VLAN # 10

  For example let's say that 1/0/1 interface connects your firewall, which has an IP 10.10.10.1 30 assigned to its interface. This means that we would assign 10.10.10.2 30 to VLAN 10.

  # interface vlan 10

  # 10.10.10.2/30 ip address

  Then place the interface 1/0/1 in access mode for VLAN 10.

  # interface gigabitethernet 0/1/1

  switchport mode access #.

  # switchport access vlan 10

  Enable the VLAN routing on the switch.

  # ip Routing

  Define a static route pointing out traffic at the firewall.

  # ip route 0.0.0.0 0.0.0.0 10.10.10.1

  Orders of trunking VLAN are very similar to the Cisco commands.

  # interface gigabitethernet 0/1/1

  switchport mode trunk #.

  # permit switchport trunk VLANs 1-1024

  Here is a link to the user's guides:

  http://Dell.to/1ZTGjsI

  And here is another link to some useful white papers:

  http://Dell.to/1cxlYEX

  Hope this helps

• VM 2 or more share a WAN connection

  Hi all

  Excuse me move if this is the wrong place for this post, etc...  Relatively new to ESXi and I don't know if I want to do is possible.  I have a Server with 4 GB Supermicro intel NIC.  I have one of these NICs connected to my internet provider (WAN) and the other for the HP ProCurve (LAN).  I'm testing different solutions UTM/Firewall (pfSense, Sophos UTM, etc.) and would like to have at least two of them operational at the same time.  The problem is that if it gets turned on first gets a WAN IP and take "control" of the WAN connection.  Whatever it is started after the first primer fine but the WAN interface will not obtain an IP address and be down. 

  Some thoughts that I had were perhaps to be the gateway to the virtual computer to imitate the same MAC address, I found a few posts that seem to indicate that Comcast modem binds to the MAC for something like this the first connects to.  Has begun research on this so I do not know how 'true' which is, or even if it is if it would help me get to where I want to be.  I hope that he stays the way to achieve this using vnetworking ESXi.

  In any case thank you for your time and I really appreciate any help you can provide!

  Having your machines virtual theft same mac will be chaos in the networking and a damaged arp table. The problem here is that your internet service provider provide only one device with an IP address. How to solve this problem is to have a router/firewall VM that is the only internet available VM and then have the other virtual machines behind it and use the port forwarding.

  Another solution is to use a loadbalancer as Kemp, where you can use expedition based URLS and so on. In short, do NOT spoof mac address, it will just make chaos.

• Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  Why my ipad loses the wifi connection when I abandon my modem wireless of Qwest

  WiFi connections are losing their strength increases the distance between the router and so as a general rule, there are some conflicting objects

  Try the following steps please

  The following actions and after each test to see if the issue is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  4. Settings - WiFi - < network name > - Click on forget network - do a restart forced according to 3 and then add again the network
  5. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  6. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  7. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  8. Backup the device to iTunes - restore as NEW (no) - see if solves problem - if yes - restore backup
  9. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• Equium M70: card wireless regularly abandons the connection

  Hi, I wonder if anyone can help. My map regularly just Equiuim M70 wireless abandons its connection. If you browse on wireless networks, it seems my WEP encrypted network and it's one to connect to, as it says "Automatic" by him.
  If you click Connect it crashes with just "Waiting for network. So he can reconnect I have to go to network connections, right-click on the wireless connection, turn it off, then turn it back on and then it reconnects quite happy.
  I have the latest version of the installed Intel drivers and am allowing Windows XP manage connections.

  My Thinkpad R50 does not suffer the same problems. My wireless hub is a Dlink G604T.

  Has anyone else had similar problems - y at - it a cure? Is this a case of return my M70 and to repair/replace?

  Thank you

  Hello

  This problem also appears if WEP encryption is disabled?
  To me, it sounds like the card is not able to take the IP address automatically.
  This similar issue happens on my Toshiba laptop not. Sometimes, I have to use the repair of the WLan connection option to renew the ip address.
  It s not very serious problem for me and I can live with this question.

  I read in a net that can sometimes happen because of encryption theWEP and SP2.
  But if you want to get more details on the legs of connection on the M70, I suggest linking the Toshiba service partner in your country.

• NETGEAR D6200 abandons the connection

  My netgear d6200 sometimes abandons the connection to my ISP, Ive tried to pass by the resolution of the problems several times and it goes through me by the same steps over and over until he finally asked my ISP details and then connects again and works fine.

  Additional information:

  1 details are all correct

  2 restart does not help

  3. it may take up to 2 hours just to do my job in connection

  Hi @Doswa

  Welcome to the community!

  You have the connection Mode is set to "Always On"? Otherwise, set it to this mode and observe your connection.

  What is the version of firmware installed on your gateway modem?

  In addition, make sure that you have the latest firmware installed on your device.

• Dell Server randomly abandons the connection to users.

  My Dell Server randomly abandons the connection to users in a building where the server does not find.  Different computers will sign the account and then randomly lose the connection to the server.  Thoughts?

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• How can ensure me that I am connected to the Wan, not the Base Station?

  I have one extreme as a base station, with an express the upstairs of the extension of the network. There are green lights on both, the utility displays the Express connected to the extreme and it is not a big house, so it seems that the network is configured correctly.

  However, when I'm near the Express, my MacBook Pro connection speed is significantly slower: 9Mbps, vs 30Mbps when close to the extreme. As far as I know, I am always connected the low extreme, rather as the Express I sit beside.

  Is there a way to say that I am connected to? Or y at - it a way to choose who to connect to?

  Thank you-

  In AirPort Utility, click images extreme and Express. A list of connected devices appears in the windows that appear.

• App of Watch sounding abandons the connection to their iPhone app

  I used Smart sounding for about a year to control my hearing aid Linx2 with my iPhone and Apple Watch successfully. However, recently, the app shows interrupts the connection to the iPhone app. Hearing AIDS continue to work well with the iPhone, but they do not meet the application of the watch. Everyone knows about this problem? I reinstalled the apps and rebooted the on both devices. If! restart the watch, the app connects, but the connection is soon dropped. I don't know if the problem related to recent IOS upgrading or something else. Any thoughts on how to solve this problem will be appreciated. Thanks in advance!

  Have you tried devices pair the two UN - force to restart both of them and then re - pair again?

  Cancel the twinning of your iPhone - Apple and Apple Watch Support

  Restart your Apple Watch - Apple Support

  Apple Apple Watch support - Setup & matching-

• My 2008 imac has twice in the last month abandoned auto connect and restore needed. After the first restoation, it was Ok but used the manual connection. On conversion automatic return, he went for a week and has not yet. I'm OK, leaving on the manual

  My 2008 iMac interrupted twice by automatic logon. After the restoration of the first time, a month before, it wasOK on a manual connection until I converted to automatic, I restored again and it's OK, apparently, when the manual connection. Can there be an underlying cause that should I worry about the?

  Download and run Etrecheck.  Copy and paste the results in your response. Etrecheck is a diagnostic tool that has been developed by one of the most respected users here (and recommended by Apple Support personnel) of the CSA to provide a snapshot of the system and to help identify the most obvious culprits of software that can adversely affect the performance of Mac.

  

• EA4500 and PS3 abandons the connection

  I had a router WRT54G2 and started having trouble with my PS3.  It would connect for a few minutes then she would lose the internet connection.  I thought that maybe it was the router so I have now from the EA4500.  The same problem occurs again.  I have all my other devices wireless connected to the EA4500 without any problems.  The PS3 will connect and connect and then two or three minutes, I get disconnected.  I called Sony and Cisco to help and they were not able to understand the problem.  The PS3 is showing that my network has almost 100% signal strength, so this isn't a problem.  If anyone has experienced this or can help, I would be very grateful!  Thank you.

  @2shibas

  Hello

  Is this connected by cable or wireless your PS3? Have some port numbers for Sony, so you can do Port Forwarding on the user interface of the router? If this is not the case, try to contact Sony and ask for the ports necessary for the opening of your PS3.

• WRT54GL abandons the connection when you are using the 2.4 Ghz cordless phone.

  I recently upgraded to a Linksys WRT54GL router and also hooked into a phone jack of magic using a 2.4 Ghz cordless phone. The interent connection is perfectly fine until I try to use the wireless phone.

  Within 60 seconds, the completely wireless signal drops and interrupts the connection from the phone. About 30-60 seconds later the wireless signal comes back and sometimes the computer reconnects automatically.

  My router is in a totally different room on one ground other than cordless phone base, and I already changed the channel on my router for 11. My computer is the only thing in the House using the Wi - Fi connection at the moment. What causes this problem & how to fix it?

  p.s. The wired computer sees no interruption of internet connection while the phone is in use.