M1000e with M8024 (problem connecting to pass)
I have a Dell Poweredge M1000E Blade chassis with two switches of the M8024.
I configured the IP addresses of the M8024 (B1 and B2) on the CMC web.
All ports on the controllers of chassis are connected to my network.
I can connect without problems to the M8024 into the slot in B2, but cannot connect / ping / access the M8024 in B1. I have tried power cycling/replace the switch but no luck.
Any suggestions? I tried not to do anything via a SERIAL connection.
I understand the problem!
CMC M1000e chassis preview / network / config VLAN. The VLAN Tag parameter has been activated for the M8024 in B1. This prevented work properly on our network, because the vlan defined for the specified VLAN ID was not set up. I unchecked the box in the column "Enable" (for B1) and he now available!
Thank you!
Tags: Dell Switches
Similar Questions
-
Problems with the internet connection, Aspire V15 - V3 - 575G
Hi, I bought a new laptop and have problems with the internet connection without having to install other programs.
The problems are the following:
- I use an ethernet cable to connect and just after passing on the laptop, there is no Internet connection at all. I have to restart the router to do.
- When downloading or uploading brokes down at intervals of 30 seconds - 1 minute. It is not always the same. Sometimes it works 3 minutes, but it is not enough.
He has Win10... With my old laptop with Win7, I had no such problems. I do not change ISP.
I don't know what to do to fix it. I have not tried to uninstall Acer applications yet. Have you experienced something similar?
Thank you very much for the reply.
Plese try this:
device, right-click on your network card Realtek Manager choose uninstall and tick to uninstall the software if requested, restart, and then try again to install the downloaded driver.
-
* Original title: 0xc00000e9
Hi all
I had a problem - would be great if someone could help me!
=====
Windows has encountered a problem communicating with a device connected to your computer.
This error...
File: / Boot/bcd
Status: 0xc00000e9
Info: An unexpected i/o error has occurred
==========
I press ESC = exit or enter = continue it tries to start, but eventually back to the black screen. So I can't pass this screen. I do not of hava a recovery for Windows disk... And the laptop is a Sony Vaio with Windows 2008. A couple of days, I have connected to my work through the laptop environment and forgot to close - battery went down--and now this...
Can anyone help?
Please see the message (response) by Afsal Taher:
http://answers.Microsoft.com/en-us/Windows/Forum/all/new-computer-running-Windows-7-unexpected-IO-error/46b4fc7a-9a83-4db2-9a00-dca512797e61 -
Problem with "vpn sysopt connection permit.
Hi all
I would like to ask you for advice with "vpn sysopt connection permit". I have a problem with by-pass-access list (acl) in the INSIDE interface. As I understand it and I'm going to use this command, there is no need to especialy allow traffic in the access list for the INSIDE and I can control the filter-vpn traffic. But in my case it's quite the opposite, I want particularly to this INTERIOR acl traffi. When I allow this traffic inside acl L2L tunnel rises, hollow traffic flow vpn-fltr ane acl that everything is OK. But when I do not allow that this traffic is inside of the rule with Deny statement in acl INSIDE block traffic and tunnel goes ever upward. Part of the configuraciton which you can view below.
Please let me know if I'm wrong, or what I did wrong?
Thank you
Karel
PHA-FW01 # view worm | Worm Inc
Cisco Adaptive Security Appliance Software Version 4,0000 1
PHA-FW01 # display ru all sys
No timewait sysopt connection
Sysopt connection tcpmss 1380
Sysopt connection tcpmss minimum 0
Sysopt connection permit VPN
Sysopt connection VPN-reclassify
No sysopt preserve-vpn-stream connection
no RADIUS secret ignore sysopt
No inside sysopt noproxyarp
No EXT-VLAN20 sysopt noproxyarp
No EXT-WIFI-VLAN30 sysopt noproxyarp
No OUTSIDE sysopt noproxyarp
PHA-FW01 # display the id of the object-group ALGOTECH
object-group network ALGOTECH
object-network 10.10.22.0 255.255.255.0
host of the object-Network 172.16.15.11
PHA-FW01 # show running-config id of the object VLAN20
network of the VLAN20 object
subnet 10.1.2.0 255.255.255.0
L2L_to_ALGOTECH list extended access permitted ip object object-group VLAN20 ALGOTECH
extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH
Note EXT-VLAN20 of access list =.
access list EXT-VLAN20 allowed extended ip object VLAN20 ALGOTECH #why object-group must be the rule here?
access list EXT-VLAN20 extended permitted udp object VLAN20 object-group OUT-DNS-SERVERS eq field
EXT-VLAN20 allowed extended VLAN20 object VPN-USERS ip access list
EXT-VLAN20 extended access list permit ip object VLAN20 OPENVPN-SASPO object-group
EXT-VLAN20 allowed extended object VLAN10 VLAN20 ip access list
deny access list extended VLAN20 EXT ip no matter what LOCAL NETS of object-group paper
EXT-VLAN20 allowed extended icmp access list no echo
access list EXT-VLAN20 allowed extended object-group SERVICE VLAN20 object VLAN20 everything
EXT-VLAN20 extended access list deny ip any any newspaper
extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH
GROUP_POLICY-91 group policy. X 41. X.12 internal
GROUP_POLICY-91 group policy. X 41. X.12 attributes
value of VPN-filter ACL-ALGOTECH
Ikev1 VPN-tunnel-Protocol
tunnel-group 91.X41. X.12 type ipsec-l2l
tunnel-group 91.X41. X.12 General attributes
Group Policy - by default-GROUP_POLICY-91. X 41. X.12
tunnel-group 91.X41. X.12 ipsec-attributes
IKEv1 pre-shared-key *.
PHA-FW01 # show running-config nat
NAT (EXT-VLAN20, outdoors) static source VLAN20 VLAN20 static destination ALGOTECH ALGOTECH non-proxy-arp-search to itinerary
network of the VLAN20 object
dynamic NAT interface (EXT-VLAN20, outdoors)
group-access to the INTERIOR in the interface inside
Access-group interface VLAN20 EXT EXT-VLAN20
Hello
The command "sysopt connection permit-vpn" is the default setting and it applies only to bypass ACL interface to the interface that ends the VPN. It would be connected to the external network interface. This custom has no effect on the other interfaces ACL interface.
So if you initiate or need to open connections from your local network to remote network through the VPN L2L connection then you will need to allow this traffic on your LAN interface ACL networks.
If the situation was that only the remote end has launched connections to your network then 'sysopt permit vpn connection' would allow their connections around the external interfaces ACL. If If you have a VPN configured ACL filter, I think that the traffic will always accompany against this ACL.
Here are the ASA reference section to order custom "sysopt"
http://www.Cisco.com/en/us/docs/security/ASA/command-reference/S21.html#wp1567918
-Jouni
-
Having problems with SQL Developer connection to the database on a LINUX machine
Having problems with SQL Developer connection to the database on a LINUX machine
Hello
I am trying to connect my machine to windows 7 Home premium to an oracle database 11 g on RedHat 5 machine using SQL Developer. I got this error on SQL Developer
Status: Failed - Test has failed: the network adapter could not establish the connection
on Linux
and TNSPINGLSNRCTL> status Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1))) STATUS of the LISTENER ------------------------ Alias LISTENER Version TNSLSNR for Linux: Version 10.2.0.1.0 - Production Start Date 03-APR-2013 16:13:13 Uptime 7 days 22 hr. 16 min. 41 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File /u01/app/oracle/product/11.2.0/db_1/network/admin/listener.ora Listener Log File /u01/app/oracle/product/11.2.0/db_1/network/log/listener.log Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1))) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=172.X.X.X)(PORT=1521))) Services Summary... Service "PLSExtProc" has 1 instance(s). Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service... Service "orc11g" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... Service "orc11gXDB" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... Service "orc11g_XPT" has 1 instance(s). Instance "orc11g", status READY, has 1 handler(s) for this service... The command completed successfully LSNRCTL>
Tnsnames.ora on Linux,tnsping 172.x.x.x TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 11-APR-2013 14:32:17 Copyright (c) 1997, 2005, Oracle. All rights reserved. Used parameter files: /u01/app/oracle/product/11.2.0/db_1/network/admin/sqlnet.ora Used EZCONNECT adapter to resolve the alias Attempting to contact (DESCRIPTION=(CONNECT_DATA=(SERVICE_NAME=172.x.x.x))(ADDRESS=(PROTOCOL=TCP)(HOST=172.x.x.x)(PORT=1521))) OK (0 msec) [oracle@ltebilling ~]$
Listner on Linux,ORC11G = (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 172.x.x.x)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = orc11g) ) )
hosts/ect/Linux,SID_LIST_LISTENER = (SID_LIST = (SID_DESC = (SID_NAME = PLSExtProc) (ORACLE_HOME = /u01/app/oracle/product/11.2.0/db_1) (PROGRAM = extproc) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1)) (ADDRESS = (PROTOCOL = TCP)(HOST = 172.x.x.x)(PORT = 1521)) ) )
and there is no problem to ping linux from windows# Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost 172.x.x.x LTEBilling
Published by: user11309581 on April 11, 2013 15:16user11309581 wrote:
as I have already desciped earlier, I can't connect to the server throw Linux my Windows SQL Server, with error message below.
tatus: failed - Test has failed: the network adapter could not establish the connectionIt's too generic to mean anything. The application is hidden the real error message. You got when you did the tnsping and obtained "TNS-12535: TNS:operation has expired. Now THAT's an error.
This indicates a problem firewall and routing. You said earlier you could ping the server, but now we see tnsping fails. Two different protocols of usage, so that both the successful ping turns out a valid physical path, it guarantees not that all traffic will pass. What happens with
c:\ telnet 172.x.x.x 1521
-
After a problem with a mobile connection, I tried with mozilla to connect to nooz.gr , but I've redirected the page services of vodafone, everytime I try again to open this site specific mozilla still redirects me vodafone support page, how can I regain access to nooz.gr?
Could clear you cookies and cache and check it out.
The problem happened when you connect your mobile connection he tries to display the service vodafone page, and it is not updated because of cookie issue.
Try in safe mode
-
Problem connecting wireless with my Tecra A8
Hello
I have problem connecting WiFi with my laptop Tecra A8. When I opened my laptop, it does not connect to the wireless network.
I tried several ways to solve this problem.
I updated for active connections, then I click on the Connect button after you select my wireless LAN, but it doesn't connect.
Or I restart my computer, but it doesn't connect.
However, it connects to the network wireless in anytime after about 15 minutes.Also when I tried to connect to the network wireless at home, but I couldn't t connect. I removed the password for the connection. Then I connected without any problem.
I wonder that there is no problem with installation? Or my wireless card doesn't work?
Can someone help me?Thank you
> Also when I tried to connect to a home wireless network, but I couldn't t connect. I removed the password for the connection. Then I connected without any problem.
According to the statement, all looks like that you try to use a password for encryption wrong!
-
Problems connecting to Exchange with Droid 3
I have problems connecting to the Exchange Server in my company with my new Droid 3. I've updated the original Droid, who had no problem connecting. I noticed a difference between the old email on the Droid app and new on the Droid 3 is that the original app was a setting for «Allow all certificates» My company allows our own certificates, and I wonder if my problem may be related to that. I exported my certificate of my desktop and installed on the Droid 3, but appears not to have had any effect.
When I try to configure my e-mail via Corporate Sync account, I get an error: "cannot connect to the server. The server is running, and everything else can connect fine.
Does anyone have any suggestions? I installed (hopefully temporarily) touch to access my business account, but I prefer not having to pay for a feature I would have already.
Thank you.
-
HP Pavilion Notebook-15-p108tx: problem connecting with specific programs
Hi, I had problems connecting with specific programs recently. I'm still able to communicate online through web browsers. Mozilla Firefox works fine, but Google Chrome still has some problems loading of specific pages or they don't load at all. The main programs I am having difficulties with are mainly games platform programs like Steam, Battle.net, and League of Legends, and I'm unable to go online or to connect to their servers.
I never had no problem connecting like these last two years that I've owned my laptop, until recently. I think it was the 6th or 7th of may these problems started.
I updated my drivers and was constantly check to download the most recent. I don't know if it's my internet provider, but I was also constantly check the State of the network to ensure that the services are very good.
If anyone else has this problem and if there are any suggestions that you think could help solve this problem, it would be appreciated.
Thank you
Jasper
Hi Jasper,.
Thank you for the update. I think that your computer have a rootkit infection. Most of them were inside of the Chrome Extensions.
Here's what you need to do.
Open chrome
Click on the Menu bar in the upper right
Click more tools
Click Extensions
Please search for suspicious extensions that does not belong to the computer, especially ads. Once you identified, simply click the trash can icon then Chrome close then reopen it again to see if you can connect to your desired game. If this isn't the case, then proceed as follows.
Manual removal of suspicious files (if you are uncomfortable with it. If this is not the case, then run System Restore from safe mode with command prompt)
Manual removal (I miss the old days of MS virus removal )
Go to RUN type %temp% , and then delete all folders by pressing SHIFT + DELETE
Go to Control Panel and then locate all the apps that you think a form of ads
Go to safe mode with network. Run Malwarebytes in that State
Then run Tweaking tool to fix everything that has changed since your computer
http://www.Tweaking.com/files/setups/Tweaking.com_windows_repair_aio_setup.exe
If your not comfortable with the troubleshooting steps may perform the system restore on the day, it was working fine.
-
Hi there I have an acer aspire one and I have a problem with my wireless connection.
Hi there I have an acer aspire one and I have problems with my wireless connection.it is connected, but I can't use internet.any thoughts? Thank you
A look at the "front" face, under the lip of the keyboard, similar to where a lock would be on a laptop. There is here a cursor that is not a lock, but it is a switch that activates / deactivates him wireless on and outside. Slide it on until it turns on the light above it (with the logo of the antenna), indicating wireless is turned on and drag it again to turn it off.
-
tvwizard2ft.exe
I have problems connecting my laptop to the TV with 2 ft HDMI connection. Whenever I try to connect "Windows cannot detect tvwizard2ft.exe" appears.
Download and install the latest graphics driver. Visit the website of intel to get that. Once downloaded unzip the file and search for tvwsetup.exe.Run this file.
You may also download and install .NET Framework 3.0 (SP2)
-
I installed AVG 9.0 and now I get the MSN Explorer pop next message.
You can not connect to your mail server. There may be a problem with your Internet connection, or a problem with the mail server. Pleas try again.Sure. Analysis of your e-mail anti-virus program:
- Can slow to receive and send messages, or even fail.
- Can damage files of storage for messages that you've already sent and received, making it inaccessible messages.
- Is not necessary. If you receive an infected attachment and try to open it, the protective device in real time of your antivirus program will block the infection.
Here are a few web pages accurately:
Why you don't need your anti-virus program to scan your e-mail
The other threat email: the Corruption of files in Outlook Express
Why some antivirus software can change the settings in e-mail programs
Email scanning - advantages and disadvantages -
I'm having a problem with my wireless connection. I have to keep in with zero wireless configuration to connect to the internet almost whenever I start the computer. Usually, you must configure only once and his game, but I have to keep on my new Dell Precision 6400 reconfigure it. I use downgrade XP on vista.
Hi Susancav,
Welcome to Microsoft Windows Forums!
I'll be your message to the category of xp windows for a better answer. You can always find your message by going to my Threads in the section My Forum links at the top right of the page. http://www.Microsoft.com/windowsxp/expertzone/newsgroups.mspx
Thank you and best regards,
Bindu S - MICROSOFT SUPPORT
Visit our Microsoft answers feedback Forum and let us know what you think. -
having problems connecting to some websites with spa3102
Hello
I have problems connecting to some websites with spa 3102.
The error message I get is as follows.
The connection was reset
The connection to the server was reset while the page is loading.
* The site may be temporarily unavailable or too busy. Try again in a few
moments.* If you are unable to load any pages, check your computer's network
connection.* If your computer or network is protected by a firewall or proxy, make sure that
that Firefox is permitted to access the Web.When I connect to my ISP modem directrly, so I'm able to connect to these Web sites.
Any ideas?
I already had the latest firmware (software Version: 5.1.10 (GW))
But I think the problem is now resolved. Sites that I couldn't visit were my suppliers Web hosting and my own domain. Previously, I had activated attacking and that my hoster somehow registeren my mac address.
Here are the settings that I had to change the spa3102.
MAC Clone settings
The Service Enable MAC Clone: Yes cloned MAC address: xxxxxxxxxxxxthx for your help.
-
I run Windows Vista. Recently on commissioning the first thing that appears on my screen is a 'Windows Live Mesh' message, "there could be a problem with your internet connection.
connection. Ensure that the computer is connected to the internet and try again".
My computer is connected to the internet, and it works very well. How can I get rid of this annoying message.
I tried all means to find this file on my computer, but it does not appear to be
Can you help me please
Mike Gray
Hello
Were there any changes (hardware or software) to the computer before the show?
Perform the check and the boot if the problem persists.
To help resolve the error and other messages, you can start Windows XP, Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.
Note: Follow step 7 to reset the computer to start as usual after the boot process.
Hope that helps.
Maybe you are looking for
-
How can I get rid of the maleware lunaticake?
I've recently updated to OS X El Capitan 10.11.3 worm on my Mac Book Pro. Don't know how, but I am now happy with Lunaticake. It has supported Google as my default search engine in Chrome and Safari. I took it my Safari extensions, I could not find
-
Can not find the ACPI driver for windows 8.1 for g40 - 80
I can't find the ACPI driver for lenovo g40-80. I tried the win10 version, but it did not work. Could someone kindly help?
-
USB/Virtual COM port Communication problem with ESP301/LabWindows/CVI
Hi all I have gone through different threads posted in this forum for similar issues and all tried, but nothing helped. I'm trying to communicate to the ESP 301 training monitor via a USB port configured as a serial COM port using a CR. Have it ' com
-
I read the following ARTICLE https://TechNet.Microsoft.com/en-us/library/cc938196.aspx And, according to the definition Definition: -. Determines the highest port number TCP can assign when an application requests a port available for the system user
-
What has become of the tool select 'UI guide"to animate it?
HeyaWhen I used Flash CS6, I would use the tool to select black to clean quickly and efficiently to the top of my brush lines.When I pressed on the edge of a STROKE at cs6, it would happen:In Animate is is no longer the caseand I can't find an option