m8024-k connection switches to cisco 5 k
We have two blade m1000e, each with 2 switches m8024-k chassis. We use this document (see link below) to connect to four cisco 5 k
http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20065722/download.aspx
We chose to use the scenario 3 (page 15) in the document. The first scenario (scenario 1, page 5) shows allowing covering tree of weight before the introduction of the LACP Protocol on the m8024-k, but not other scenarios in the document do. So if we use scenario 3, we wouldn't have this exact tree, covering weight - activated?
Scenario 1 gives a specific example to allow the same protocol Spanning Tree on the Cisco and M8024-k switches. Scenario 3 is the addition of this option gives an example of how allow multiple VLANs through this same SHIFT (aggregation of links). It's not one or the other or a situation.
Theoretically you won't need to covering tree enabled on the 2 switches, if it's the only connection switch. The OFFSET is considered by protocols spanning tree as a single cable connection. So no blocking would take place or be required to maintain an environment free of loop.
That said, I recommend always leaving protocols spanning tree active. It won't hurt to have is running. It is advisable to have it activated on your switches. They are different available commands to manipulate a tree covering weight on different ports. As the portfast. It allows a port to an edge device to immediately enter a status of the shipment.
Tags: Dell Switches
Similar Questions
-
I bought a SGE2010 and a SGE2000P passes. I want to connect these two switches. What I need to buy a mini-GBIC MGBT1 and connect that way, or can I use a switch on each switch port and connect them like that?
Is the MGBT1 really just a module to connect to the switch via a gigabit with Cat5 network non-gigabit
There are no modules mentioned to connect switches, with what I read of the Cisco and Linksys help page. However, you can go to the link I have provided below. This is an article on the Cisco site, which deals with the stackable switches of EMS and EMS. Not as simple as we judge well.
http://www.Cisco.com/en/us/products/ps9967/products_qanda_item09186a0080a362e3.shtml
-
PowerConnect switch and Cisco routers
I have 4 Cisco routers connected to our Dell Powerconnect 7024. This is a laboratory environment where I'm having every act of router (2 per site) as a WAN gateway for these 2 sites.
Site 1 Site 2
2 3 router
PC - Dumb_switch PowerConnect Dumb_switch client - PC Client
Router 1 router 4
There are a few other Vlans on the switch with connected devices. With the current configuration, these two sites can communicate with any other "site" connected to the switch on each route, with the exception of the other.
Directly connected to the router interfaces are in trunk mode, as it's the only way I could get the dell to connect with the Cisco. Ive read in other threads that the general mode is usually suggested on the powerconnect switch, but had no luck with this configuration.
Router 1---> item in gi1/0/15 (vlan 10)
Router 2---> item in gi1/0/14 (vlan 11)
Router 3---> item in gi1/0/22 (vlan 16)
Router 4---> article gi1/0/23 (vlan 14)
Example: a ping from Site 1 can reach int 22 of the switch without problem, but I can't ping jump according to R3. As all the other devices on this switch can talk to these sites, I'm not clear if the problem is my config switch dell or routers. Any input would be greatly appreciated. Thank you!
! Current configuration:
! Description of the system "PowerConnect 7024, 5.1.2.3, VxWorks 6.6"
! 5.1.2.3 system software version
! 'Normal' system operation mode
!
Configure
GVRP enable
VLAN 2-7, 9-14, 16
output
VLAN 2
name 'BOSTON '.
output
VLAN 3
name "MIAMI".
output
VLAN 4
name of 'THE
output
VLAN 5
name "SEATTLE".
output
VLAN 6
name "DALLAS".
output
VLAN 7
name "London".
output
VLAN 9
name "Frankfurt".
output
VLAN 10
name "Rome".
output
VLAN 11
name "Sczecin.
output
VLAN 12
name "Budapest".
output
VLAN 13
name "Moscow".
output
VLAN 14
name "Quebec".
output
-Other - or ITU (q)
VLAN 16
name "Winnipeg".
output
hostname "Devlin".
location 1/0 2. PowerConnect 7024
clock timezone-5 minutes 0
battery
1 2 Member! PCT7024
output
out-of-band interface
Shutdown
output
no ip domain-lookup
"local" IP domain name
IP routing
IP route 0.0.0.0 0.0.0.0 172.16.37.3
IP route 172.16.37.160 255.255.255.240 172.16.37.162
IP route 172.16.37.112 255.255.255.240 172.16.37.162
IP route 172.16.37.112 255.255.255.240 172.16.37.147
IP route 172.16.37.144 255.255.255.240 172.16.37.147
IP route 172.16.37.240 255.255.255.240 172.16.37.244
IP route 172.16.37.224 255.255.255.240 172.16.37.244
IP route 172.16.37.224 255.255.255.240 172.16.37.217
-Other - or ITU (q)
IP route 172.16.37.208 255.255.255.240 172.16.37.217
ARP 172.16.37.162 0022.9057.7F51
interface vlan 1
IP 172.16.37.4 255.255.255.240
bandwidth 10000
IP ospf cost 10
output
interface vlan 2
IP 172.16.37.17 255.255.255.240
output
interface vlan 3
IP 172.16.37.33 255.255.255.240
output
interface vlan 4
IP 172.16.37.49 255.255.255.240
output
interface vlan 5
IP 172.16.37.65 255.255.255.240
output
interface vlan 6
IP 172.16.37.81 255.255.255.240
output
interface vlan 7
-Other - or ITU (q)
IP 172.16.37.97 255.255.255.240
output
interface vlan 9
IP 172.16.37.129 255.255.255.240
bandwidth 10000
output
interface vlan 10
IP 172.16.37.145 255.255.255.240
bandwidth 1000
IRDP IP
output
interface vlan 11
IP 172.16.37.161 255.255.255.240
bandwidth 1000
IRDP IP
output
interface vlan 12
IP 172.16.37.177 255.255.255.240
bandwidth 100000
output
interface vlan 13
IP 172.16.37.193 255.255.255.240
bandwidth 1000
output
interface vlan 14
IP 172.16.37.209 255.255.255.240
bandwidth 1000
output
interface vlan 16
IP 172.16.37.241 255.255.255.240
bandwidth 1000
IP ospf cost 100
output
No flowcontrol
!
interface item in gi1/0/3
spanning tree portfast
output
!
interface item in gi1/0/4
spanning tree portfast
output
!
interface item in gi1/0/5
spanning tree portfast
switchport access vlan 2
output
!
interface item in gi1/0/6
spanning tree portfast
switchport access vlan 3
output
!
interface item in gi1/0/7
spanning tree portfast
switchport access vlan 4
output
!
interface item in gi1/0/8
spanning tree portfast
switchport access vlan 5
output
!
interface item in gi1/0/9
switchport access vlan 6
output
!
interface item in gi1/0/10
switchport access vlan 7
output
!
interface item in gi1/0/11
spanning tree portfast
switchport mode trunk
output
!
interface item in gi1/0/12
spanning tree portfast
switchport mode trunk
output
!
interface item in gi1/0/13
switchport access vlan 9
output
!
interface item in gi1/0/14
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 10 tag
switchport access vlan 10
output
!
interface item in gi1/0/15
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 11 tag
switchport access vlan 11
output
!
interface item in gi1/0/16
switchport access vlan 12
output
!
interface item in gi1/0/17
switchport access vlan 12
output
!
interface item in gi1/0/18
switchport access vlan 13
output
!
interface item in gi1/0/19
switchport access vlan 13
output
!
interface item in gi1/0/22
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 16 tag
switchport access vlan 16
output
!
interface item in gi1/0/23
Speed 100
full duplex
switchport mode trunk
VLAN allowed switchport General add 14
switchport access vlan 14
output
!
interface item in gi1/0/24You could probably create a static route in Router 1 router 4 with a priority which is better than the other options, so we're going unless the link is down.
-
Help with M6348 connecting to a Cisco network
Hello
Can someone help me with best practices by putting R710 via a M6348 stacked with a cisco network.
Our configuration is the following
M1000e
2 x 1 GB pass-through fabric a
2 x M6348 wired in a pile in the B fabric
6 x popular R710 with four NIC ports in the fabric B (3 are general purpose servers, 3 are Hyper-V servers in a cluster)
Cisco network
For most of the Cisco 3560 switches
20 VLAN (1 per building) configured, mainly for the isolation of traffic (VLAN 300-320)
What (I think) that we want to
The M6348 connect to the core network in a SHIFT (4 x 1 GB ports. Can it be divided 2 ports each of the stacked M6348?)
Have a mapping of right for 1-3 to VLAN 301 R710
Configure R710 4-6 for access to all VLANS for the Hyper-V hosts can be placed on the VLAN correct
Use the fabric for the connection to the San
Network management is carried out by a third party (we are unable to change this) and they claim that they are unable to connect Cisco/Dell!
We are server guys, guys network no, so something stupid (especially for Cisco to give to our management company) would be appreciated.
We tried to configure the switches in Simple mode, using a Dell deployment guide, but all we seem to get is the default VLAN to all ports on the switch 1 battery, but no other VLAN and no active port 2 in the stack.
I've probably missed lost info on and were not very clear, so if more info is needed, please get back to me.
Thanks in advance for the help
Rich
Thanks for the information updated, actually, this confirms that the problem is with the connection to the Cisco switch. Is that what we tried a general link, instead of trunk?
mode console # switchport general
Console # switchport General allowed vlan add 300-320 tag
Console # pvid General switchport 301
Console # end
Are we sure that the VLAN 301 IP address is 10.49.56.0? This doesn't seem fair.
When we try to pings on the trunk/General connection to the Cisco switch, make sure you that the servers have the default gateway defined on the VLAN IP address they are in access mode. Thus, when in the access mode VLAN 301 the gateway server would need to be 10.49.56.0. I would like to verify that the IP address, however.
-
NAC - STACKED IN THE AUTHENTICATION VLAN IF THE PC IS CONNECTED TO THE CISCO IP PHONE
Hello
I have configured my NAC in L3OOB, if I connect my pc directly to the switch I have no problem, I can access the network as out-of-band user, I can pass authentication. BUT IF I CONNECT a Cisco ip to switch phone and my pc is connected to the Cisco ip phone I'm stacked to the vlan authentication and cannot access the network. The event logs of the my CAM, it's say that it detects several mac address.
Please guys help me with this problem...
Thank you and best regards.
Hello
Have you added your phone MAC address to your CAM in the filter to IGNORE it?
Faisal
-
Unable to connect to the Cisco VPN you use native client: El Capitan
I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."
When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:
* connect using the old work VPN connection: without success
Config: Hand [server address, account name],
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
...
* Add new VPN connection using L2TP over IPSec: without success
Config: Hand [server address, account name],
Authentication settings [user authentication: password, identification of the Machine: Shared Secret].
Advanced [send all traffic on the VPN = TRUE]
errsors:
"pppd [2616]: password not found in the system keychain.
"authd [124]: copy_rights: _server_authorize failed.
...
* Add new connection using Cisco via IPSec VPN: without success
Main config: [server address, account name].
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
VPN server is high and does not work and accepts connections, this problem is entirely on the client side.
I. Journal of Console app existing/Legacy VPN connection:
26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status
26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 405 [2580]: connection.
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.
[26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting
26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).
26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
[26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
$VPN_SERVER_IP
II. new VPN connection using L2TP over IPSec Console app log:
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856
26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13
26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]
26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.
26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain
26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback
26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed
26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify
III. New connection of Cisco VPN through IPSec Console app log:
26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status
26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 296 [2576]: connection.
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: connection.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.
[26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting
26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).
26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
[26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
It seems that I solved the problem, but I'm not sure it helped.
After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.
-
Unable to connect via the Cisco VPN Client
Hello
I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0
I am not able to connect and watch the journal on the SAA
ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!
ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry
ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.
What could be the reason.
Concerning
Hi, I had this same problem, here is the solution:
When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.
Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.
Well, change your strategy using MD5 isakmp / OF would do the trick.
-
Unable to connect to the Cisco VPN using the branch line
Hello
We use Cisco VPN Client 5.0.07.0290 to connect to our servers. We have a Sonicwall NSA2400 FW and we have 2 ISPS. We have configured load balancing on firewalls in mode 'Spill-Over '.
So whenever the 1st line is on full charge, it will automatically moves users on the 2nd line.
The problem that we face here is the users who get 1st line ISP, they can easily connect to the client VPN Cisco IP, but the users who receive the IP of the 2nd line of the ISP, they are not able to connect to the Cisco VPN Client. It's really annoying because everyone should be able to connect.
It will be really great if someone can help me as well.
Thank you
PS: If Exchange us the line of Sonicwall haapens scenario of Vice versa as mentioned above.
Hello Sam,.
Correct me if I help you,.
In your network that is inside the firewall, you are trying to connect to Cisco VPn client resides outside your network/Public network.
If the above is the question.
Please check the routes and roads of sonicwall priority.
example:
Isps1: the value of the metric as 1 for traffic destined for cisco VPn IP of the gateway and specify to leave traffic isps1 interface
ISP2: set the metric 1 once again for the traffic to cisco VPn IP of the gateway and specify to leave traffic ISP2 interface
interface metric 1 source destination
Kindly, please note the useful messages and.
Thank you
Srikanth
-
Mapping of ports of the blade and Powerconnect M8024 - K Ayala switch 1 GB based Trunking
Hello world
Nice day!
We have a recent deployment of server blade to one of our customer and we met a challenge regarding the following:
-How are we going to map the internal blade to the Powerconnect M8024-K NIC. Port 1-16 is for VLAN 1000. PowerConnect M8024-k is configured with module additional uplinks (GB 2 x 10 base-T). What is the module has the ability to auto negotiate to 1 GB. We want to use this port for connections to the switch avaya 1 GB Ethernet based. The port of internal network to blade port 1-16 must go through this port goes to the external network (switch Avaya)
-Do we really need to configure for this port. Is 10 GB base-T port has the features of auto-negotiation up to 1 GB
Thanks for your help
copilot0929
Here are some documents that detail the M1000e IO options and internal correspondence of ports.
The M8024k will automatically negotiate 1/10 GB for all internal ports. SFP 4 external / SFP ports + are has several ports support 1/10 GB speeds. The external ports also need a transceiver that supports the speed you want to use.
VLAN tagging is used when needing to send traffic to several VLANs over a single connection. If everything on the chassis will be in the same VLAN, then you should not have to put in place a trunk. But if you need the chassis to participate in several VLANs, so it is better to configure the VLAN Trunk on that connection.
-
M1000e with M8024 (problem connecting to pass)
I have a Dell Poweredge M1000E Blade chassis with two switches of the M8024.
I configured the IP addresses of the M8024 (B1 and B2) on the CMC web.
All ports on the controllers of chassis are connected to my network.
I can connect without problems to the M8024 into the slot in B2, but cannot connect / ping / access the M8024 in B1. I have tried power cycling/replace the switch but no luck.
Any suggestions? I tried not to do anything via a SERIAL connection.
I understand the problem!
CMC M1000e chassis preview / network / config VLAN. The VLAN Tag parameter has been activated for the M8024 in B1. This prevented work properly on our network, because the vlan defined for the specified VLAN ID was not set up. I unchecked the box in the column "Enable" (for B1) and he now available!
Thank you!
-
PowerConnect 6248 switch for Cisco router
Hello
I'm new to this forum and I have a problem at the moment between a Cisco router and a dell pc6248. The problem is that I lost conectivity in VLAN 1 when I connect the router to a trunk port in the switch, however I conectivity VLAN 2 through this link to trunk. The configuration of the switch:
interface ethernet 1/g48
switchport mode trunk
switchport trunk allowed vlan add 1-2
output
interface ethernet 1/g43
switchport mode access
switchport access vlan 2
output
On router
fast interface 0/1
no ip address
no downtime
fast interface 0/1.1
encapsulation dot1q 1 native
IP 192.200.3.1 255.255.255.0
fast interface 0/1.2
encapsulation dot1q 2
IP 192.168.51.33 255.255.255.248
output
With the above configuration, I lost conectivity with the host in the vlan 1 - 192.200.3.x/24, but I win conectivity VLAN 2, when I connect the router to the 48 trunk port in the switch. This means that the trunk link for VLAN 2 work but not for VLAN 1.
I read on the port of general mode, where I can configure the pvid of the port as 1 (vlan1) and it would be the unttag VLAN (even natively in Cisco), and I can configure the VLAN 2 like the tag, all this in the same port. What do you think about this? Someone have set up something like that?
Best regards
Erasmo
PD: I write from Chile, I apologize for my English.
I agree with you, I would try the general mode on the PowerConnect switch.
mode console # switchport general
Console # switchport General allowed vlan add 2 tag
Console # switchport pvid General 1
Keep us updated.
-
Discover device directly connected to the cisco ASA
How do I know which is directly connected to an ASA interface? I'm looking for some commands that can be executed on the SAA to find the directly connected Cisco device.
Thank you
Boudou
Unfortunately it is not available on SAA for you tell what device is directly connected to it, there is no 'see the neighboring cdp' on SAA unfortunately.
You can check the ARP table and see which is the next hop, but who would only give the layer 3 device, such that there could be a switch between the two institutions.
-
How to connect switch processor on 6500?
Here is the release of version see the:
Cisco Internetwork Operating System software
IOS (TM) software to MSFC3 (C6MSFC3-PSV-M), Version 12.2 (17 a) SX1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Updated Thursday 29 October 03 03:57 by next
Image text-base: 0x40008FBC database: 0x41E94000
ROM: System Bootstrap, Version 12.2 (17r) S2, RELEASE SOFTWARE (fc1)
XXXXX availability is 16 weeks, 4 days, 5 hours, 25 minutes
System returned to ROM by unknown charge cause - suspect boot_data [BOOT_COUNT] 0 x 0, BOOT_COUNT 0, BOOTDATA 19
System restarted at 10:23:42 GMT Monday, August 26, 2013
System image file is "bootflash:c6msfc3 - psv - mz.122 - .SX1 .bin 17A"
Cisco ( MSFC3 (R7000) processor with 458752 K / 65536 K bytes of memory.
Card processor ID XXX
SR71000 pace at 600 Mhz, implemented 0 x 504, Rev 1.2, 512 KB of L2 Cache
Last reset of tension
X.25 software Version 3.0.0.
Connection software.
15 virtual Ethernet/IEEE 802.3 interfaces
512 KB of non-volatile configuration memory.
8192K bytes of packet buffer.
65536 K bytes of Flash internal SIMM (sector size of 512K).
Configuration register is 0 x 2102
********************************************************************************************************
I tried to connect to MS by issuing the command "login remote swtich", but this command is not recognized:
Switch connection host #remote name
^
Invalid entry % detected at ' ^' marker.
#remote host name?
% Unrecognized command
How can I see the modules of the line connected to this switch and how to connect the switch processor?
Hello
Your switch runs hybrid, which means it runs CatOS on the SP and IOS on the RP. You are connected to the RP to be able to use the hybrid you must first connect to the SP and then you can get the PR by issuing the command-session 15 that will register you in the RP that takes place in IOS. To return to the SP just type "exit" and it drops you to MS.
Hope this helps. !
-
I was able to connect to Cisco before. Today all of a sudden, I get this message from the plugin crash. I have even tired of reloading the page, but nothing helped.
If you use the version of ESR Firefox 17.0.11 (help > subject) then you can upgrade to the current version of Firefox 24.3.0 ESR.
-
Vista Equium A100-027: start Wireless connection switch
Whenever I turn on the machine it powers upward normally, but I find that the network connection has not been made. When I check, I think that the light on the wireless switch does not light even if the switch is in position "on" where I left it.
I have the wireless switch and the new and the light and the machine connects. You have to do with the wireless switch whenever you turn on the machine? Certainly it should connect automatically if left in position one.
Hi, I have exactly the same problem with my laptop equium A100-338, the answer to your question is Yes, the light should come back on after restart or boot closure like mine to do this, but now it is a very annoying task that I have to keep flicking the switch off then on again to get a connection.
I'm sorry I can't be of any help on how to get the light stays on has im still waiting for an answer to this.
Maybe you are looking for
-
Satellite P300D-12Y - problems with the support of the multimedia button/buttons
Hellofirst sorry for my English bad propably. I had a problem a few days ago, I heard yesterday. On my laptop, I have 6 keys for some functions.Here is a picture where you can see what buttons I mean. I mean the six buttions between the speakers.[htt
-
Some problems after the connection of the universal adapter for Satellite M-series
Can anyone help? I have 2 young children and through wear my adapter has fought for a new one of toshiba that's 60 books that I am on a tight budget, I opted for a universal adapter that says you can use on any laptop. When I plug it, it powers my la
-
move or copy large files in Vista 32
I can't move or copy files with size of GB files but files suits MB seems to wrk.
-
The search in a single user account does not work.
Original title: Research on Windows 8 Research on a Windows 8 does not (by typing in the menu start is nothing, Windows + F - nothing happens, do a right click on start-> Search-nothing happens) while working on other accounts. What causes this probl
-
I have a new pc with windows 8 and 10 of the IE and cannot install firefox?
I have a new pc with windows 8 and 10 of the IE and cannot install firefox? Can anyone help?