M8024 K-switch Cisco WS - 2960 S-24TD-L switch interconnection

Hello

I have 4 ports SFP + Module switch M8024-K. I want to establish connectivity 10Gig between M8024-k and Cisco WS-C2960S-24TD-L switch. I'm not able to find the exact Dell transmitter/receiver part number required for 4-port SFP + Module and cord Patch LC - LC-OFC required dell. I have no problem with Cisco parts.

Kindly suggest exact reference numbers.

Jean Marc

This transceiver is listed on the list of compatibility of the server but not the switch. It can work in the switch, but I can't confirm that it will be because he is not on the compatibility list.

Tags: Dell Switches

Similar Questions

  • Cisco Catalyst 2960-S switch configured for 802. 1 x sends a query to access the Radius Server Radius

    Setup

    Cisco Catalyst 2960-S running 15.0.2 - SE8

    Under Centos freeRadius 6.4 RADIUS server

    Client (supplicant) running Windows 7

    When Windows client is connected to the port (port 12 in my setup) with authentication of 802. 1 x active switch, show of Wireshark that catalyst sends ask EAP and the client responds with EAP response. But it made not the request to the Radius server. The RADIUS test utility 'aaa RADIUS testuser password new-code test group' works.
    Here is my config running. Any advice would be greatly appreciated.
    #show running mySwitch-
    mySwitch #show running-config
    Building configuration...

    Current configuration: 2094 bytes
    !
    version 12.2
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    no password encryption service
    !
    hostname myswitch
    !
    boot-start-marker
    boot-end-marker
    !
    activate the password secret 5 $1$ Z1z6$ kqvVYRQdVRZ0h8aDTV5DR0 enable password!
    !
    !
    AAA new-model
    !
    !
    AAA dot1x group group radius aaa accounting dot1x default start-stop radius authentication group!
    !
    !
    AAA - the id of the joint session
    1 supply ws-c2960s-24ts-l switch
    !
    !
    !
    !
    !
    control-dot1x system-auth
    pvst spanning-tree mode
    spanning tree extend id-system
    !
    !
    !
    !
    internal allocation policy of VLAN no ascendant interface FastEthernet0 no stop ip address!
    GigabitEthernet1/0/1 interface
    !
    interface GigabitEthernet1/0/2
    !
    interface GigabitEthernet1/0/3
    !
    interface GigabitEthernet1/0/4
    !
    interface GigabitEthernet1/0/5
    !
    interface GigabitEthernet1/0/6
    !
    interface GigabitEthernet1/0/7
    !
    interface GigabitEthernet1/0/8
    !
    interface GigabitEthernet1/0/9
    !
    interface GigabitEthernet1/0/10
    !
    interface GigabitEthernet1/0/11
    !
    interface GigabitEthernet1/0/12
    switchport mode access
    Auto control of the port of authentication
    dot1x EAP authenticator
    !
    interface GigabitEthernet1/0/13
    !
    interface GigabitEthernet1/0/14
    !
    interface GigabitEthernet1/0/15
    !
    interface GigabitEthernet1/0/16
    !
    interface GigabitEthernet1/0/17
    !
    interface GigabitEthernet1/0/18
    !
    interface GigabitEthernet1/0/19
    !
    interface GigabitEthernet1/0/20
    !
    interface GigabitEthernet1/0/21
    !
    interface GigabitEthernet1/0/22
    !
    interface GigabitEthernet1/0/23
    !
    interface GigabitEthernet1/0/24
    !
    interface GigabitEthernet1/0/25
    !
    interface GigabitEthernet1/0/26
    !
    interface GigabitEthernet1/0/27
    !
    interface GigabitEthernet1/0/28
    !
    interface Vlan1
    IP 10.1.2.12 255.255.255.0
    !
    IP http server
    IP http secure server
    activate the IP sla response alerts
    recording of debug trap
    10.1.2.1 host connection tcp port 514 RADIUS-server host 10.1.2.1 transport auth-port 1812 acct-port 1646 timeout 3 retransmit testing123 key 3.
    Line con 0
    line vty 0 4
    password password
    line vty 5 15
    password password
    !
    end

    interface GigabitEthernet1/0/16
    !
    interface GigabitEthernet1/0/17
    !
    interface GigabitEthernet1/0/18
    !
    interface GigabitEthernet1/0/19
    !
    interface GigabitEthernet1/0/20

    Have you run wireshark on the server because the request to switch? If so you make sure that there is a response from the server? For Windows network POLICY Server (I've never tried Centos), you must ensure that the request is related to a policy which then authenticates, or denies access. Usually, it is a matter of such attributes and the seller.

    Regarding the configuration, it seems a bit out of the AAA. Try to remove the:

    line "aaa dot1x group service radius authentication" and this by using instead:

    "aaa dot1x default radius authentication group". After the dot1x word you are supposed to provide a list of the authentication or the default Word if you do not want to use a list.

  • 6248 FI Cisco's UCS with Cisco catalyst 2960 connectivity

    In our environment, UCS, connects the two fabric as a Cisco Nexus 9 k switch upstream with vPC and it works well. But we need to isolate some virtual servers on the blades of the UCS on an entirely separate DMZ switch which is Cisco catalyst 2960.

    (1) so can we connect cables separate physical twinax of FI uplink ports to catalyst 2960 and connectivity to the servers in the DMZ keeping YEW to nexus connectivity as it is?

    (2) in this case, as there are 2 switches to nexus core 1 and 2 so we will require 2 cisco catalyst 2960 for disjoint such a network? or otherwise we can connect A FI and FI B to one on his 2 numbers 2960 switch. Gig SFP ports + 10?

    (3) also suggest things must be taken in charge, the best guides practice or an illustration in this context.

    The assignment is static and cannot be changed.

    location 1 - uplink 1

    slot 2 - uplink 2...

    If a property has no blade, the corresponding uplink is not used and that can not be changed!

    This dedication of uplinks of IOM is of course a lot of resources: cables, ports on FI, allowed port,...

  • Best wiring for blade M8024-k switch stack to ToR N3048 using 10GBe modules?

    I have a M1000e with 2 x M8024-k toggle (bunk) in B1 and B2 slots, I connected the switches rack via ports of 10GbE for the 2 x N3048 (bunk)

    What is the best way to connect?  And how do I add or number connections LAG as none of them are attached to the same switch?

    Thank you very much

    Battery

    Hello

    It is a good way to connect the two piles that you can configure the link as an aggregate of 4 X 10 giga links. You should use LACP rather than static, so that any broken link is quickly identified and thus will be abandoned in the aggregate.

  • m8024-k connection switches to cisco 5 k

    We have two blade m1000e, each with 2 switches m8024-k chassis.  We use this document (see link below) to connect to four cisco 5 k

    http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20065722/download.aspx

    We chose to use the scenario 3 (page 15) in the document.  The first scenario (scenario 1, page 5) shows allowing covering tree of weight before the introduction of the LACP Protocol on the m8024-k, but not other scenarios in the document do.  So if we use scenario 3, we wouldn't have this exact tree, covering weight - activated?

    Scenario 1 gives a specific example to allow the same protocol Spanning Tree on the Cisco and M8024-k switches.  Scenario 3 is the addition of this option gives an example of how allow multiple VLANs through this same SHIFT (aggregation of links).  It's not one or the other or a situation.

    Theoretically you won't need to covering tree enabled on the 2 switches, if it's the only connection switch.  The OFFSET is considered by protocols spanning tree as a single cable connection.  So no blocking would take place or be required to maintain an environment free of loop.

    That said, I recommend always leaving protocols spanning tree active.  It won't hurt to have is running.  It is advisable to have it activated on your switches.  They are different available commands to manipulate a tree covering weight on different ports.  As the portfast.  It allows a port to an edge device to immediately enter a status of the shipment.

  • 4506E Core and 2960S access IP Camera System switches

    Hi all

    I implement my first Cisco network and needed a little guidance. Here's the scenario and I wish that it works:

    • 2960S access switches will have cameras IP PoE and POS stations connected to them with the core fiber uplinks.
    • 4506E central office switch will have all the switches connected to the fiber SFP uplink ports access. All fiber optic cables are single mode with LC connectors.
    • All the cameras IP PoE and the other the camera server NETWORK card will be the 172.16.0.0/16 network and in case of default Vlan 1.
    • All computers of end users and a NETWORK card in the camera server will be on the 192.168.1.0/16 network and Vlan 2. 2 VLAN is needed as the main switch.
    • All stations of POS and stand-alone server POS will be on 192.168.20.0/16 and Vlan 3 switch network access and the base.
    • It will be a completely closed network, no internet access.
    • Computers end users will access video server with raids unicast.
    • All switches interconnect fiber SFP transceivers of 1 GB.
    • VLANs are not to communicate with eachother, just need to Vlan 1 and 3, be passed on to the switch base. It will be setting ports in the trunk switchport mode correct?
    • I gave all the devices static IP networks, with the exception of IP cameras that will get the IP Address of the DHCP server.
    • When I plug in a device of watt PoE 15.4, is the port set to auto detects by default so it lights camera or manually activate PoE on the port?

    -I have to run DHCP on central switch, only on the default Vlan 1 172.16.0.0/16 network so my IP cameras can obtain an IP address.

    IP dhcp pool cameras

    network 172.16.0.0 255.255.0.0

    default router 172.16.0.1

    -On the PoE IP camera and POS station ports I think following configuration:

    switchport mode access

    spanning tree portfast

    I would like to know what you think. I have a few weeks before they must go to the production. Any help and advice will be greatly appreciated!

    I will be checking periodically the thread and display updates.

    Yes I see!

    So with each carpet use "port 1' for each channel.

    for example

    If we have a stack, there that a single etherchannel, should therefore be port-channel 1 (the first 6). This could bind to the 4500 to Portchannel 1

    When we have the second battery, it will also be an etherchannel, which is the port-channel 1 (the first 6).

    This could bind to the 4500 on Portchannel 2

    and so on... The port-channel number is locally meaningful only so you don't meet for loops if its configured as suggested, etc...

    This way you can keep it simple and you will have ease of management in this way.

    No, there is no point linking medical examinations to configure

    Hope it makes sense.

    Please evaluate the useful messages, & mark as answer questions thank you.

  • 2960S and REP

    Hello

    I recently bought a number of switches Cisco 2960 S-24TD-L and would like to know if they support REP (resilient Ethernet Protocol). I've implemented a development space and have telnet would be one of the 2960 to attempt to configure a Port on board, but I keep getting the 'invalid command' response when the representative of Word is used.

    The current software is 12.2 (55) SE7.

    Any help would be appreciated.

    See you soon

    Tom

    Hello, Tom.

    2960S does not support it.

    By my understanding, this is a feature of the ISP, supported on IE3000, ME and other IOSs "ISP feature.

  • Make a choice of switching - catalyst 500/520/ESW Linksys SRW / SFE

    Hello someone would be able to clarrify please where Cisco takes in what concerns the SMB switching product portfolio that I'm getting a little confussed.

    My estimate that we currently have available that which follows to the SMB market, has decided there is a price difference significant between some of the product lines, but it seems that the choice when choosing a suitable switch fades a bit and starts to go down in price rather than the features and performance characteristics.

    • Cisco Catalyst Express 500 series switches
    • Cisco Catalyst Express 520 series switches
    • Cisco Small Business Pro ESW 500 series switches
    • Cisco Small Business Managed switch (Linksys Business Series)
    • Cisco Small Business Smart switch (Linksys Business Series)
    • Cisco Catalyst 2960 Series switches
    1. Can I ask if there are plans to merge some of the ranges of products like the 500 and 520, which are the two similiarly priced, managed in almost the same way and have the same function defined.
    2. Are there plans for the ESW line replace the Linksys SRW/SFE and Cisco 500/520 existing equivalents?
    3. I would correct assuming the ESW line runs the Code of IOS?

    Any help would be appreciated.

    Concerning

    Mark Rigby

    Mark,

    Big questions.  Thanks for posting.

    1. Yes, you can expect that over time, the ESW 500 series will replace the Catalyst Express series.

    2. There are no plans for the series of ESW 500 replace SRW/SFE switches.  These product families are somewhat overlapping, but intended for different types of SME customers and partners VAR.

    3. you are incorrect in assuming that the ESW is base IOS.  It is not the case.

    The attached PDF provides a comparison of high-level Cisco switches that sell on SMB.

    Thank you

    Florian

  • Dot1x multidomain on Catalyst 2960

    Hello

    I improved my 2960 with the latest basic version of LAN 12.2 (46) which includes the authentication of domain Multi (MDA) and I tried to configure what is described here:

    http://www.Cisco.com/en/us/Tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml

    I have the following exceptions in my configuration:

    (1) SE - cat 2960 with the latest version of IOS 12.2 (46) that supports the MDA;

    (2) using the Win2K IAS as a server radius. and

    (3) third party (Avaya) with active begging dot1x IP phone. I have a PC with ability to dot1x connected to the second port of the IP phone.

    That's what I set up on the phone IP port:

    interface FastEthernet0/9

    switchport access vlan 221

    switchport mode access

    switchport voice vlan 222

    dot1x EAP authenticator

    self control-port dot1x

    multi-domain host-mode dot1x

    protect the dot1x violation-mode

    dot1x reauth-deadline 30

    dot1x re-authentication

    spanning tree portfast

    I also configured the server Radius IAS Win2K to send RADIUS 'cisco-av-pair attribute' tell the authenticator (Cisco Catalyst 2960) that a supplicant (IP phone) is authorized on the voice VLAN as described in config-notes above link.

    When the supplicant IP phone starts to authenticate, he succeeds, but that the port does not allow the field of VOICE, even though the 2960 receives the attribute "cisco-av-pair" of the Radius Server RADIUS. I confirmed the reception of this attribute of debugging on the switch.

    RADIUS: Receipt of id 160.2.100.74:1645 1645/64, Access-Accept, len

    110

    17:02:38: RADIUS: authenticator 7 d AC 50 FE 14 B4 FC DC - 3A A4 E5 3F 1E 76 62

    C3

    17:02:38: RADIUS: EAP-Message [79] 6

    17:02:38: RADIUS: 03 05 00 04

    17:02:38: RADIUS: [25] in class 32

    17:02:38: RADIUS: 44 05 05 A2 00 00 01 37 00 01 A0 02 64 4A C9 01 1 33 79 52

    D8 58 00 00 00 00 00 00 1 b E7 [D7dJ3yRX]

    17:02:38: RADIUS: seller, Cisco [26] 34

    17:02:38: RAY: Cisco-AVpair [1] 28 'device-traffic-class = voice.

    17:02:38: RADIUS: Message-Authenticato [80] 18

    17:02:38: RADIUS: D9 42 78 88 26 5A 65 83 68 B0 E0 C7 AF 5TH 0F 51 [B

    [x & Zeh ^ Q]

    17:02:38: RADIUS (00000009): receipt of id 1645/64

    17:02:38: RADIUS/DECODE: EAP-Message fragments, 4, total 4 bytes

    Cat2960 #show dot1x int fa0/9 details

    Dot1x FastEthernet0/9 information

    -----------------------------------

    EAP AUTHENTICATOR =

    PortControl = AUTO

    ControlDirection = both

    HostMode = MULTI_DOMAIN

    Violation mode = PROTECT

    A re-authentication = on

    QuietPeriod = 60

    ServerTimeout = 0

    SuppTimeout = 30

    ReAuthPeriod = 30 (configured locally)

    ReAuthMax = 2

    MaxReq = 2

    TxPeriod = 30

    RateLimitPeriod = 0

    Dot1x authenticator customer list

    -------------------------------

    Domain = DATA

    "Supplicant" = 0004.0d9b.46d8

    AUTH State = AUTHENTICATED SM

    AUTH BEND State IDLE = SM

    Port status = AUTHORIZED

    ReAuthPeriod = 30

    ReAuthAction = is re-authenticated

    TimeToNextReauth = 20

    Authentication method = Dot1x

    Authorized by = authentication server

    Policy of VLAN = n/a

    I don't think I need CDP to allow the field of voice, if the Radius server sends the attribute "cisco-av-pair".

    Have I misunderstood the concept?

    Thank you!

    You can share the config switch?

    Missing for example aaa authorization network default radius group?

  • Infrastructure 2.0 Cisco first deployment models

    Hello world

    I wanted to deploy a configuration model 'first infrastructure 2.0. I tried with the output of the model "banner Configuration-IOS" box. I have deployed it to a device that is a switch to Cisco Catalyst 2960 - 24PC - L. I chose "Add" in the menu dropdown 'Connection Action' and typed in 'Test' in the field 'login Message. All the rest is the default value. After you apply the changes, I clicked on the Ok"" button. After this IP trying to deploy the model configured on this device. A few seconds later the 'Last Run status' column in the 'jobs' dashboard, said "failure." The 'summary', said:

    "Error in the execution of XDE procedure, Error Message::No 'CLI_ENABLE_PASSWORD' attribute for the device"2344372"

    I tried to figure it out and searched the Internet but I couldn't find a solution.

    Thanks in advance for your efforts!

    Have you confirmed that the enable password is correct in the credentials of the device? (Device Center, select and modify the devices)

  • M8024-k and 6248

    Hi all

    I have a Dell M8024-K pass with a dual port DELL 10GBaseT expansion card in the connector 1. It is possible to connect one of its 10 GB ports with a 1 GB on a Dell 6248 switch port or availabe ports on DELL 10GBaseT expansion card y t uplink provided just M8024-k switches?

    I tried to connect a port on DELL 10GBaseT expansion card to a port on a Dell 6248 switch, but the link is down.

    Thank you

    A.

    The M8024-K can be connected to the 6248, but must be made using the same interfaces to speed. 1 GB to 1 GB or 10 GB to 10 GB. 10GBaseT expansion card does not support 1 GB connections. The 6248 has provisions for a plug-in SFP +.

    http://Dell.to/1XP25ve

  • Dell TL4000 Tape Library on Cisco UCS 6120

    Hello

    We have Cisco UCS 5108 2 6120XP fabric of interconnection. We are running VMware on my Cisco blades. I have I need to connect my Dell TL 4000 LTO3 tape library this Cisco UCS so that I can configure a virtual machine with the EMC Networker software for backup of virtual machine data. When I connect the Cisco UCS library, it does not recoginize as tape drive.

    Please suggest how to set up the same.

    Thank you

    Amit,

    We do not support direct damage attach FC tape library to the FI currently.

    It may be a CF or CF storage end switch.

    . / Afonso

  • Interconnection of fabric as FC switch

    Hello

    can we use a 6120 as a FC switch interconnection, so do the CF normal zoning stuff and connect directly to some CF storage to the FC expansion ports, or do we need run the interconnection in NPV mode and connect it to a switch taking NPIV.

    Kind regards

    John

    If my memory is good, you will need to use the VAN.  Direct attach storage support comes in v1.4, which is due to be released in January.

    Adam

  • can you connect the SFP - 10 G - SR low-support to SFP 1000BASE-SX?

    Hello world:

    today I use the SFP + 'SFP - 10 G - SR' in Cisco Catalyst 2960 S-48TD-L connect to the SFP 1000BASE-SX to 6509 WS - X 6724-SFP module.

    the port setting is master, but they do not work, even the light don't flush. Then, I also use the SFP 1000BASE-SX to replace SFP + SFP - 10 G - SR in

    2960 S-48TD-L, then they cany working.

    I look to the top of the cisco data sheet, there is no roadmap to satament database 10G sfp + can't low support 1 G sfp. So, I want to confirm the problem.

    Otherwise, the 10 FPS + can only use for 10G SFP +; can't go down the suport 1 G SFP.

    This means: If you want to use the 10 G SFP + the other old device also need to replace.

    Thank you ~ for your help!

    Hi Marvin,.

    I found this conversation today, because I'm looking for an answer on a question similar to the question that Jerry asked, at the opening of this discussion.

    So my problem is this. In a certain place, I need two 10 GB and a connection of 1 GB on an optical cable. To cut costs, I tried with WS-C2960X-48FPD-L, but because it contains only two ports of SFP +, I tried with two WS-C2960X-24PD-L which will be connected with the battery modules.

    Then, having two WS-C2960X-24PD-L, I have 2 x 2 ports SFP + 1 GB. There are two open questions:

    1. can I put 1 GB transmitter SFP module SFP + port (that I have a connection of 1 GB at remote site)?

    2. can I use two switches to 24 ports mentioned 2960, in a way that I use one of them for the two connections of 10 GB (using ports SFP + 10 GB connection) and the second member of the battery so that we (2 available) port SFP + is used to 1 GB SFP connection (using the SFP port + as mentioned in question 1)?

    I'm not sure if your previous statement covers my questions, because it is not clear if the 1 GB SFP transceiver can be inserted in the port SFP + WS - C2960X - 24PD - L (or any other a port SFP switch +).

  • CiscoWorks LMS 4.1 monitor temperature

    Hello everyone!

    I am creating a poller to monitor the trap of the temperature of my cisco catalyst 2960 Ciscoworks LMS 4.1.

    I created a snmp trap on my device:

    Switch(conf-t) # snmp-server <@IP_server_LMS>SNMPv2c host -I use SNMPv2c

    Switch(conf-t) # Server enable snmp traps envmon temperature

    I created a MIB model Envmon with these variables:

    -ciscoEnvMonTemperatureThreshold

    -ciscoEnvMonTemperatureStatusValue
    -ciscoEnvMonTemperatureState
    -ciscoEnvMonTemperatureLastShutdown

    I created a poller associated with my model, I add my device and when I click on 'Next', I have this error message:

    ###

    No instance are in the devices. This could be because the device is inaccessible, the device does not have the case for selected models or the timeout value is low.

    ###

    Could someone explain to me why I can't monitor MIB?

    Thanks for your consideration and Merry Christmas to all!

    It seems that most of the 2960 have a temperature sensor implemented in hardware and therefore, it shows no values.

    If a device does not show anything on CLI, it is almost impossible that it will display something via SNMP.

    -Thank you

Maybe you are looking for

  • How to remove "Installers" from my hard drive

    Recently, when Safari was a problem with the search function I used Bitdefender to do an analysis of the system deep before I knew how to fix Safari re: search suggestions I thought I had some kind of virus. However, when I did this analysis thorough

  • Identification of the monitor

    I recently acquired a TOSHIBA monitor model No. DA1566M-01 which was manufactured in December 1996. can someone help me identify this monitor or help me to find technical information about him?It also has a control Module attachable LCD attached to s

  • Window update is stuck at 0%

    HelloI have a problem started a few weeks ago. When my window of essential security cannot connect with update, then I noticed some automatic updates also failed.Update from my window is stuck at 0%. When I tried the automatic update of the Panel all

  • WindowsUpdate_800F081F tries to install IE9.

    I already had installed IE9 Beta but had too many problems, so I uninstalled using the util of Microsoft. Now, I can not install the version of the worm. Keep the above error. Twice he said he installed and restart, but after restarting it still work

  • Hewlett Packard Officejet 7000 e809a thick paper won't load

    Hello have problem wit my new habit of wich HP Officejet 7000 load dense environments like the 150-200 g/m2 an i just have no idea why, when it should support the card up to the 200 media and photo media up to 280 g/m2, no way here is a video and a f