Made a bridge network distort your IP address for file sharing via a WIFI network?

Similar Questions

• How can I connect Windows XP to several networks, Wi - Fi for internet and the other for file sharing?

  On windows XP, I need to connect to two different networks. Free wifi for the internet and the other for file sharing.

  Different gateways, different static address, same subnet mask. But there is problem when operating simultaneously and must

  a network must be disabled. Is it possible to run simultaneously?

  original title: served various networks simultaneously on windows xp

  Go to where you have configured the static IP addresses for your network adapters.  Leave the "default gateway" blank for your local file sharing adapter and insert a valid default gateway for your wifi Internet adapter.  Of course, this will limit your adapter in a single subnet - which should be OK for use at home or small office to share local files.

  This should work as long as the two physical subnets have two different subnet numbers. In general, this means that the first three digits of the IP address of the adapter can not be the same on both adapters - if they are, then you need to make one of the subnets. (i.e. one is 192.168.1.xxx and the other would be 192.168.2.xxx).  This is usually accomplished in the router configuration page.

  HTH,
  JW

• In trying to "turn on network discovery", I got this message: "the specified service does not exist as an installed service. Ditto for "file sharing." How can I activate them?

  In trying to "turn on network discovery", I got this message: "the specified service does not exist as an installed service.  Ditto for "file sharing."  How can I activate them?

  Hello

  Method 1: Make sure that the following services are enabled on the computer.

  (a) click Start and type "services.msc" in the search and click on services and ensure that these services are enabled:

  -TCP/IP NetBIOS Helper service

  -DNS Client

  -Function Discovery Resource Publication

  -SSDP Discovery

  -UPnP device host

  To start the service and set it to automatic, follow these steps:

  (b) right click on each of the services listed above and click Properties.

  (c) click the general tab, and then, next to startup type, select automatic.

  (d) click on apply and then click Start.

  Method 2: I suggest that you can exercise SFC scan and check if TI the problem persists. To do this, please see the following article. The SFC/SCANNOW command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  For more information how to make SFC / scan, please follow this link:

  http://support.Microsoft.com/kb/929833

• Domain network cannot activate file sharing and print?

  Hi all

  I get an error message when you try to share a folder "an error has occurred. trying to share folderxxx Incorrect function ". After research I see that file and printer sharing is not enabled.

  I went to control panel | Network and sharing Center. Advanced settings - sharing on the "Discovery of the network" and "File and printer sharing" I select "turn on...» "for one or the other and save changes - but neither is saved! Ebb in advanced sharing settings both return to "Turn off"... "State. (I am local and domain admin).

  Windows 7 computer is joined to a domain and the firewall settings are defined mainly through Group Policy, although local settings are allowed (merged).

  I would add that I can access the admin shares (c$, d$) on the computer without problem on the network so advanced in this regard firewall settings are ok.

  At a loss as to why file and printer sharing will not allow?  Thank you.

  I found what was wrong or the problem.

  During the process of deployment of our new systems Windows 7 wipe us the rules of default outgoing firewall who do seem to not be a problem because outbound connections have been set by default to "allow". But we have learned that only when outbound rules for file sharing and printer available (enabled or not) can share news can be created.

  After the creation of the joint ownership, these outbound rules can be removed and sharing still works fine to keep rules to incoming traffic.  I guess this is normal, but it is not quite make sense to me why the outbound rules are explicitly required for files and printers share when you create a share... but that is what has worked for us.

  David (toyNN)

• Unable to connect to the wireless network, error message "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.

  Original title: Unable to connect to the wireless network

  Unable to connect to the network wireless Toshiba Satellite A105 PC running Windows 7.  "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address.  Works with Windows XP SP2, IE 8.00.6001.18702 file, I think that Version 3.  It has been installed on a disk provided by Microsoft after that old installation became corrupt (in the sense of Microsoft technical support.)  Before that, wireless network worked well.   (So unable to connect to the Internet for updates.)   Have tried to change the other settings and different messages acquired when it SHOWS that I am connected but cannot connect because of something to do with the certificate.  I don't remember what I did to try to solve this problem in the last days.

  I should add that I have tried the solutions of the previous forum on this topic, and none worked.

  Hi Marilynnla,

  Sorry to hear about the bad experience you encounter. Lets see if the network problem can somehow be archived.

  Read this article and follow the steps. Lets see if it helps in any way.

  How to troubleshoot wireless network connections in Windows XP Service Pack 2 (Works for Windows XP SP3 as well)

• How 'renew your IP address' to fix my wireless network connection?

  That's what said the window pop up-"windows could not finish repairing the problem because it is impossible to perform the following action - RENEWAL of your IP ADDRESS"
  Can someone help me renew my IP so my wireless works again on a laptop for a long time.

  To renew your IP address:

  1. open windows guest Start\ Run\cmd\ok

  2. to release your Ip address ipconfig/release
  Come in

  3. If you want to renew your IP address ipconfig/renew
  Come in

  Output

  Best of Luck Sohail Khan

• Ethernet link to the bridge network and server

  I'm not an expert and hope that I do not use the wrong terminology, but I have an intermittent fault which has become more or less permanent. My major son put up for me a computer with Windows 8 as its operating system and a server for storage, connected by a cable to transfer files. The computer has its own router, with which it communicates with the local network based on a router and modem in the next room. There is a network bridge to access the internet. Initially (January 2013) it worked well. Sometimes, I couldn't connect to the server immediately, but simply another attempt was enough to access it, and he had no problem with the internet connection.

  More recently (late July and August 2013), it became more difficult to access the server and now seems permanently impossible, the server simply showing with a red X across as one of the devices on the computer page. The Internet becomes also more difficult, although there is no need for the server or available to arrive and still connects for a short while before disconnect. In July, the internet can usually be restored by turning off the modem and the router, and when they were on again to restart Windows 8, but that no longer works. I tried to reset the computer to the previous settings, but without success. I also tried the diagnostics tools, but generally, they fail to address the issues identified, except for an occasional brief of the internet. Until today, it has always been possible to show the LAN on the network page, including the iMac computer and printer next to the router and the modem, but today the network folder showed most of the time as empty, any diagnosis I ran in the attempt to identify and connect to the local network, which today needs to manually connect even if automatic connection is checked. Conversely the iMac can still see the computer Windows 8 when he is awake through the LAN, but only in January, he sees the server.

  The error or the troubleshooting messages that have been published are (1) to the server: the (network) path could not be found, or the name is already used. The IP given my son is 192.168.0.101, I tried and failed to find in the browser of my iMac, which does not suggest that it is already in use. Even if it wasn't a valid IP address, it would not have worked between January and July.
  (2) for internet access: reset of the card of network bridge that can force a reboot with a reference to the AREA of PAGE_FAULT_IN_NONPAGED_ that I can't continue without an internet connection. unresolved issues can include one or all of the connection between your modem cable, router or point of access and the Internet is broken. "Network bridge" is not a valid IP configuration. the default gateway is not available. The computer in the other room has had uninterrupted access to the internet, so it is unlikely that the router or the modem it are at fault, who leaves the access point or the configuration of the network gateway. I found some of these error messages in the discussions on Windows 7, but not for Windows 8.

  Finally, the watch status bar above all a network with limited access and a connected LAN ethernet bridge, which is not enough to bring me to the server or the internet; However, today the necessary local network setting procedure of discovery of devices running and by ticking the automatic connection to the LAN router in the next room, although both had previously been functioning. Is this the consequence of Windows updates downloaded and installed since January? Very briefly this afternoon after having restorng the settings they had on August 5, the convenience store was able to solve the problem of the bridge network, only for access to the internet to be cut shortly afterwards for lack of a valid IP, a problem solved configuration a few minutes before. Would it be possible to obtain internet access directly via the LAN network without the need for a network bridge, or is it a mistaken assumption on my part? Even if this is right, remains the problem of access to the server. Any thoughts anyone?

  Hi Clive,.

  If you have included a lot of details about this question in the thread, I was unable to get a clear picture of the network configuration you have. What is the topology of the network that you set up?               How the server is connected to the network? What is a Client-Server network model you have?

  If Yes, then this problem is better suited for it professionals about TechNet Forums that are well equipped with the knowledge of Client-Server network issue. Please post your question in the TechNet Windows 8 IT Pro Networking Forums from this link:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w8itpronetworking

  Hope this information is useful.

• Help me configure bridged networking

  I just build a Dell 2950 to host three virtual servers on a production network. I installed VMWare Server 1.0.8 and have a virtual machine ready to go. The physical host that is running Windows Server 2003 R2 SP2 64-bit. The virtual host is the same except 32-bit. I have a second dedicated network adapter, I want to use for the virtual machine. I want the virtual machine to have a static IP address on my network of production, so I'm pretty sure that I need to use the bridged mode. The question that I have in fact is to configure interfaces. Configure the physical host with a static address with the virtual host with a static address? The virtual network editor DHCP service is used in this case? I disabled NAT as I did not need. Basically, in the virtual network editor I'm pointing VMnet2 on the second physical network adapter that I want to dedicate for the virtual machine.

  My network is 10.218.100.x\24 and I have a couple of addresses available for this. I have assigne.15 physical NIC host. I ai.16 par.20 available to use. Could someone provide a brief description of how I can configure the virtual network adapter to have one of these static addresses and be available on the production network?

  No reason to change how the physical host gets its IP address for this interface NIC physical - if DHCP is left, if static, leaving too.

  Treat your VM exactly as you would for any other physical PC on your network... If you have a DHCP server for this application/subnet field, then let it use DHCP; If this isn't the case, then set static - just as you would for any other real computer.

• Windows could not finish repairing the problem because it is impossible to perform the following action: renewing your IP address

  Last night after doing a reboot of my internet has stopped working.  I get the error indicated in the title, when I click on 'repair' under the Local area connection status window.

  I use a cable modem and going through a wireless router.  I know they work because I'm there access wireless typing to you all.

  When I type "ipconfig" in the cmd program, I get the following (which I thought was weird):

  Suffix the connection-specific DNS: cm

  IP address: 0.0.0.0

  Subnet mask: 0.0.0.0

  It was also strange to me that I could not access my router by typing 192.168.1.1 in my IE window.

  Also, why I type ipconfig/release, I get a message that says "IP address for the connection to the Local network map is already out." and when I type in ipconfig/renew, I get "an error occurred upon renewal of the connection to the Local network interface: the RPC server is unavailable."

  Just another note to add, I did a restore of the system to a point a week before I had the problem and I still have the same issues.

  I hope it is enough detail for each of you experts out there.  Thank you in advance! :)

  PS Sorry if this has already been answered, I was digging through forums for the last two hours.

  Your machine is not getting an IP address from the DHCP server.  Without an IP address, it will not communicate with any device on your network.  The error says "the RPC server is unavailable" or "the RPC service is unavailable"?  Whatever it is, make sure that your DHCP client service and your RPC service is running:

  Start-> Run-> "services.msc".

  In the window that appears, confirm that the "DHCP Client" and "RPC Remote Procedure Call ()" is present and that its status is "started" and its Startup Type is "automatic".  If this isn't the case, double-click top and doing it this way.  Also check your syslog, unusual errors:

  Start-> Run-> "eventvwr.msc".  Check the logs 'System' and 'Application '.

  Hope this helps,
  JW

• (SOLVED) Windows could not finish repairing the problem because it is impossible to perform the following action: renewing your IP address

  Computer Dell laptop Windows XP SP3 - processor Intel Celeron M 1.40 GHz, 512 MB Ram, ATI MOBILITY RADEON 9000

  The local connection is working fine but my wireless connection does not receive through my laptop. The wireless works since it goes through my PS3 and my sister's laptop perfectly.

  I used the repair, but it will say:
  Windows could not finish repairing the problem because it is impossible to perform the following action: renewing your IP address

  I used in the cmd command:
  ipconfig/renew
  Needless to say a message:
  No operations can be performed on the wireless network connection, although it has its media disconnected.

  Help, please

  Received my solution of another comforter

  Told to go to my router linksy page http://192.168.1.1 setup and change the wireless security mode. It is in mixed mode to WPA2/WPA and I changed it to WPA2 Personal and it worked!
  Thanks for trying to help JW! : D

• Bridged network

  Hey everybody,

  Is it possible to fill the 2 PCs/networks with different network ranges?

  Let's say that

  LAN PC 1

  IP: 192.168.100.3

  PC 2 Brigde

  PC 3 Wifi

  IP: 143.23.43.2

  Now I need to connect 1 PC and PC 3 on 2 PC with a bridged network adapter. I don't know how to set up.

  Hello

  The routers are much more easily and they don't cost much.

  These should help:

  References to Vista also apply to Windows 7.

  Set up a computer-to-computer (ad hoc) network
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  Ad hoc networking - how the network with the funny name can make your life easier
  http://Windows.Microsoft.com/en-us/Windows-Vista/ad-hoc-networking-how-the-network-with-the-funny-name-can-make-your-life-easier

  How to build a wireless network without using a router at wide band (also Windows 7)
  http://www.hardwaresecrets.com/article/how-to-build-a-wireless-network-without-using-a-broadband-router/418

  Build a Wireless Home network without a router (also Windows 7)
  http://www.labnol.org/software/wireless-network-without-router/11494/

  How to share files and printers on your network
  http://www.hardwaresecrets.com/article/how-to-share-folders-and-printers-on-your-network/247

  -------------------------------------------------------------------------

  Other solutions include the use of these that turn your WiFi PC into a virtual router
  instead of using the ad hoc network.

  Connectify
  http://www.Connectify.me/

  Virtual router
  http://virtualrouter.codeplex.com/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• ASA 5510 VPN - using a public IP address for the local network

  Hello, I have a problem which is probably very simple, but I can't seem to understand.

  I set up a site IPsec connection to another with a company, something I've done many times before without a problem. I use ASDM to configure this, because it is quick and painless, usually.

  We have one number of other site-to-site currently configured connections and works very well on this ASA, these are configured with the "Protected network - LAN" configured with the IP private of hosts within our network, we want to make available through the separate tunnels. This includes the configuration setting on our ASA for each connection to "guests aside ASA exempt from NAT.

  With this new link, however, the company asked us to use a public IP address for the host that we want to achieve through the tunnel. I don't know why, but they demand it. So I added a NAT rule for inside the host and set up the connection with the public IP address under "Local network". During the test to try to reach a host to their side, the tunnel didn't even try to open.

  What is the method here? I don't see where I'm wrong. I'm guessing that the 'host side ASA exempt from NAT' does not require for this, how if the ASA would know which internal host is the public IP address.

  Any ideas?

  Hi Leo,

  The steps are:

  1. Add the policy rule NAT for the specific host.

  2 - define the IP NAT as your LOCAL NETWORK address in the encryption settings.

  3 make sure that there is no rule NAT exempt for this host to the specific destination.

  What happens if you run a package tracer?

  Thank you.

• Bridged Networking problem - comments may be crazy, but nothing else can connect

  I have a few bridged networks confusion works correctly under VMWare Workstation 11. Installation is VMWW running on a Windows Server R2 2012 host with a Ubuntu LTS 14.04 server prompt.

  Windows Server has a physical NETWORK adapter that is configured with two IP addresses.  For the sake of argument, that I will call the first IP 1.1.1.1 (255.255.255.192 subnet mask) and the IP secondary 2.2.2.1 (netmask 255.255.255.224).  Real IP addresses are all publicly routable.

  In my computer, the network configuration is set to "bridged".  Inside of the Ubuntu VM, networking is defined as follows:

  2.2.2.2 IP address

  255.255.255.224 subnet

  Gateway 2.2.2.1

  I can ping successfully the Ubuntu prompt from the Windows Server and other computers on the Internet, but cannot connect to any other service on the client (for example, SSH, HTTP, etc.), either from the host machine or any computer on the Internet. Note that both hosts and guests have their respective firewall disable for the moment.

  However, if I change the VM network config in my computer to be "NAT" and set the networking of Ubuntu on DHCP, all services on the client are accessible on the host Windows (for example, SSH, HTTP etc.) via a 192.168.x.x dealt with this workstation DHCP assigns the guest.

  I'm a bit puzzled as to why these services would be accessible to the NAT address, but not on the static IP address public when the latter may be ping from the host and other machines?  Any suggestions would be greatly appreciated.

  OK, managed to solve it with a violin.  The resolution was to create a new virtual network adapter in the virtual network Editor.  It has been bridged, with the physical NETWORK adapter selected in the drop-down list 'Bridge '.  In this case, this has created VMnet2.  Then in the VMWare Workstation GUI, I edited the network adapter settings to select VMNet2 in Network Configuration options.

  No idea why it did not work with VMNet0 at first, but still...

• Bridged Networking crushed Vmware Fusion 6.0.4 - replicable

  I use the version of 30 trial of VMWare Fusion 6.0.4.  I can't sign up and download a .zip file officially, because I have to register the product first, and it won't let me register the serial number of the trial.  I won't pay until I am sure that it works for my use case.  So I have to resort to these forums.  Here's my reproducible bug:

  I'm running a Windows 7 VM.  I used the import function to import this machine virtual of Parallels Desktop version 9.  It starts and works fine as long as I'm using NAT networking (shared with the host).  As soon as I switch to Bridged networking, it starts and runs for about 15 to 30 seconds, then crashes.

  I used "Information Support" to create a zip of debugging information file and he have attached to this post.  Help!  I need to use Bridged networking.

  Hi petec35_2!

  It seems that your guest uses frames (or Jumbo Packet), and which is currently to trigger this problem in Fusion.

  To work around the problem: in the guest Device Manager, find the E1000/E1000e NIC, then a parameter in its property page should allow you to disable the Jumbo Frames/Jumbo Packet.

  See you soon,.

  --

  Darius

• No VMnet0 or bridged network

  I installed VMware Workstation on a system Windows 8 10.0.1.  When I open the virtual network Editor, there is no VMnet0, and I can't create a network with the bridge enabled.  I get the following error:

  Cannot change the full network: there is no host not bridged network adapters.

  Networking works very well on the host system.  I found nothing useful in the documentation that guess vmnet0 is and functional very well as a bridged network and Googling has not given anything useful yet.

  Thank you

  Curt

  I'll check the observer of events and if appropriate try to re - install with McAffee turned offshore.

  As soon as I saw "McAffee" (it's actually, McAfee) I Wen ugh!  IMO McAfee is one of the worst products personal computer firewall and AntiVirus is there and I never use it on personal computers.   You need to maybe actually completely uninstall McAfee and then install VMware Workstation.  Then test it before installing your 3rd part AntiVirus/Firewall, McAfee I hope not!