Mailer Object - specify the Port

Similar Questions

• How to specify the port in webview

  See the Web mode using a WebVPN connection interface:

  I use url = " https://X.X.X.X:4443 "

  but it doesn't seem to work, where X.X.X.X is the IP address.

  How should I specify port Web layout?

  This should be the correct way to specify a port. Are you sure that it is correct? I don't know what's WebVPN, but SSL isn't usually on port 443, 4443 (and if you were using 443, the https scheme that would use by default).

• The port forward does not work in RV120W?

  I am trying to configure a simple port forward in the RV 120W router, but can't seem to make it work.

  I created a custom service called RDP for the TCP 3389 3389 port.  I added a Port forward to always allow the RDP service, from any source to destination IP 192.168.50.23 IP address.  I tried with 'identical to incoming port' and also specified the port 3389 to forward to and to.

  Firewall access rule is activated and incoming value, always allow, RDP service, any source & destination IP, DNAT IP is 192.168.50.23.

  RDP works at the IP address of the local network.

  Any ideas?

  There is a problem with the RV220W, and work around this problem:

  Just use the firewall rules and not port forwarding.

  try on your rv120w and see.  Make sure that the last thing you do is re save firewall rule.

  It will be useful.

• How to change the Port WSX

  I should have said that I am under WS 9.0.2 (production) here.  So I do not know where to post

  My host is Fedora 19.  When I try to go to the localhost:8888 reports of Firefox "unable to connect".

  The output of netstat - ttlnp is:

  TCP 0 0 0.0.0.0:111 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:8307 0.0.0.0: * LISTEN.
  TCP 0 0 192.168.122.1:53 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:22 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:631 0.0.0.0: * LISTEN.
  TCP 0 0 127.0.0.1:25 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:443 0.0.0.0: * LISTEN.
  TCP 0 0 0.0.0.0:17500 0.0.0.0: * LISTEN 2852/dropbox
  TCP 0 0 0.0.0.0:902 0.0.0.0: * LISTEN.
  tcp6       0      0 :::111                  :::*                    LISTEN      -
  tcp6 0 0: 1:8307: * LISTENING.
  tcp6       0      0 :::22                   :::*                    LISTEN      -
  tcp6       0      0 ::1:631                 :::*                    LISTEN      -
  tcp6 0 0: 443

  Go to localhost:631 brings up the page of CUPS online.

  Maybe if I changed WSX in listening on port 8307 I might have better luck.

  But just run sudo/usr/bin/vmware-install vmware-wsx u

  and then reinstall thke bundle does not give the possibility to specify the port - I got the first time I ran the bundle.

  In which directory is the spec WSX port number and I can change it?

  -----------------------------------------------------------------------------

  This was solved by uninstalling WSX 1.02 (dereconfiguring I should say) and then installing the beta version 1.1 (allowing NoScript OK access to localhost).  Always the possibility to change change the port was not found, but 8888 worked if the thread is unanswered. .  I would like to move this thread to the WSX forum but it's fairly inactive last I checked.

  WSX login screen looks better, but it will take me a while to go through the changelog.

  Hey Buddy,

  Could you please try to modify the configuration file under/etc/vmware/wsx?

  I update the port 8888 to 8901 and restart the service. Then I can access through http://localhost:8901 wsx.

  I tried on Fedora 18 x 32.

  I hope this can help.

• Cannot open forms after changing the port no 80

  Hello
  
  We have oracle ebs 12.1.3 instance, I changed the default port 8000 to 80. Now, I'm getting the login page without specifying the port no, but my problem is that I can't launch the forms after you complete this task. can someone help me with this
  
  Kind regards
  Chandrasekhar.

  Hello

  Alhtough Web development server port does not ask that question, autoconfig successfully completed? can u try to bounce application and see if it works?

  What is the result of status adopmnctl.sh

  also check for the error in the apacha/web/form server logs, use below for MOS locate: -.
  How to find the location of installation, automatic configuration, patching, Clone and other newspapers in EBS R12 [ID 804603.1]

  Thank you
  JD

• Something similar to groups of objects, but for the ports? (must be used on an ACL)

  Hello community!

  I'm fairly new, when it comes to firewalls, but I have some experience with routers and switches, so I'm not completely lost.

  Practically, we all know that a group object is a large bucket to throw things and then managing them as a single group, which is very useful for many reasons... so is there something similar that we can use in an ACL for the port?

  Say so, let that I want to allow the following ports:

  • 80
  • 443
  • 25
  • 30500
  • 20500
  • 8080
  • 14600
  • 21
  • 753
  • 22

  And instead of doing something like this:

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 80

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 443

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 25

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 30500

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 20500

  access-list extended dmz_access_in permit tcp host WEB host WEB-EXT eq 8080

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 14600

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 21

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 753

  dmz_access_in list extended access permit tcp host WEB host EXT - WEB eq 22

  do something like:

  dmz_access_in list extended access permit tcp host WEB host WEB-EXT eq PORT_LIST1

  Thank you!!

  PD: Excuse me if some port above are not TCP, if just one example. I just start typing all the numbers that came to my head.

  Hey Rolando,

  On a SAA, you can combine services and protocols based on the source/destination in an object-group service oriented. Your example would look like this:

   object-group service PORT_LIST1 service-object tcp destination range 21 22 service-object tcp destination eq 25 service-object tcp destination eq 80 service-object tcp destination eq 443 service-object tcp destination eq 753 service-object tcp destination eq 8080 service-object tcp-udp destination eq 14600 service-object tcp destination eq 20500 service-object tcp destination eq 30500

  You can create also integrate groups:

   object-group service WEB_PORTS service-object tcp destination eq 80 service-object tcp destination eq 443 object-group service PORT_LIST1 group-object WEB_PORTS service-object ...

  This type of group is going where the Protocol is specified in the ACL:

   access-list dmz_access_in extended permit object-group PORT_LIST1 object HOST object EXT-WEB

• I get the port 25 socket 100060 error 0x800ccc0e error code and can't send email on windows mail or oe

  have tried everything to reinstall to change the port, deleted all traces of norton and still nothing

  He has worked and now is not, help!

  Windows Mail or OE is part of Microsoft office.

  Post Windows Live questions in the appropriate forum found here:
  http://windowslivehelp.com/

• Change the Port number of e-mail outgoing "587" as required to use the Comcast e-mail

  When my email out through Comcast did not all Comcast more, technical support told me that I had to change the number of Port for outgoing in Windows Live Mail beta 110 to 587.

  Worked well, until I had a system crash.

  When I reinstalled Windows Live Mail, I could fine is no longer the 'Tools' button in the status bar and by result cannot change the port number.  So, I can't send emails from Comcast of Windows Live Mail.

  The inbound port setting is apparently correct already, as I had no reception bad don't mail... sending mail.

  I hope it will work for you.  I use Windows Live Mail 2009.

  If you look on the left side of the window, you will see the name of your e-mail account.  (Underneath there is Inbox, drafts, sent items, etc.)
  You'll want to right-click on the name of the mail account. (Right above where it says Inbox.)
  Then you'll want to click on properties.
  A properties box opens.  You'll want to click on the tab "Advanced" on the right side of the Properties window.
  The first area is the SMTP (outgoing) port number.  You just want to change it in 587.

• What should be the port/security settings for Windows Mail with Vista - I think they changed?

  I had to reinstall Vista when my hard drive crashed, and Windows Mail does not work completely correctly. I think remember me an email from Microsoft told me to change the ports/security settings. Could someone tell me what they should be?

  A "error message indicating", what exactly? No error code or the relevant text?
   
  Make sure these settings match exactly.
   
  Set up Windows Mail for E-mail XFINITY/Comcast
  http://customer.Comcast.com/help-and-support/Internet/configuring-Windows-Mail-Xfinity-email
   
  
  Leave messages on the server and it clutter?
   
   

• Darkness of 8.4 (1) vpn L2L filter ASA when you specify the Protocol and port

  Hi all - I've spent many hours trying to diagnose this and have read several discussions and the Cisco docs unsuccessfully...

  Situation: two sites running Cisco ASA 5520 on 8.4 (1) with L2L IPsec on the public internet between each of them. The configuration of IPsec and associated routing works as it should and we are able to pass traffic between networks private behind each device as expected. The problem occurs when you try to block sessions using a vpn-filter group policy configuration.

  Each site has 3 private subnets that are able to communicate correctly without the vpn-filter configuration. We want to restrict access to specific protocols, hosts, and ports between each network.

  SITE A: 10.10.0.0/18, 10.10.64.0/18, 10.10.128.0/18

  SITE B: 10.20.0.0/18, 10.20.64.0/18, 10.20.128.0/18

  When we apply a filter-vpn configuration which restricted access only two guests, as follows...

  SITE A: vpn_acl_x_x_x_x list extended access permit ip host 10.20.0.1 host 10.10.0.1

  SITE b: the ip host 10.10.0.1 allowed extended access list vpn_acl_x_x_x_x host 10.20.0.1

  ... the configuration works correctly. However, when we try to lock the configuration more far and specify the protocols and ports, as follows...

  SITE A: vpn_acl_x_x_x_x list extended access permit tcp host 10.20.0.1 host 10.10.0.1 eq 22

  SITE b: vpn_acl_x_x_x_x to the list of access permit tcp host 10.10.0.1 host 10.20.0.1 eq 22

  ... and then try to establish a SSH connection between 10.10.0.1 and 10.20.0.1 or vice versa, the package is stopped on the side of the SOURCE. ..

  Mar 22 11:58:01 x.x.x.x 22 March 2011 14:34:56: % ASA-4-106103: vpn_acl_x_x_x_x of the access list refused tcp to the user "" inside-data/10.10.0.1(59112)-> outside-iptrans/10.20.0.1(22) hit - cnt 1 first success [0xd8d1c1b4, 0 x 0]

  I would really appreciate it if someone could shed some light on what is wrong with this Setup.

  SOLUTION
  

  The ACE must be implemented on the source and the end of the tunnel destination to facilitate this configuration.

  EXAMPLE 1: allow SSH two-way communication between hosts on each network (SITE A can connect to SITE B, SITE B can connect to SITE A)...

  SITE A:
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.20.0.1 host 10.10.0.1 eq 22
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.20.0.1 eq 22 host 10.10.0.1
  SITE B:
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.10.0.1 host 10.20.0.1 eq 22
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.10.0.1 eq 22 host 10.20.0.1
  

  EXAMPLE 2: allow communication one-way SSH between hosts on each network (SITE A can connect to SITE B, SITE B is unable to connect to SITE A)...

  SITE A:
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.20.0.1 eq 22 host 10.10.0.1
  SITE B:
  access-list vpn_acl_x_x_x_x extended permit tcp host 10.10.0.1 host 10.20.0.1 eq 22
  

  Very good and thank you for this post. Please kindly marks the message as answered while others may learn from your post. I think that you have started a very good discussion on vpn-filter for tunnel L2L.

• Is there a way to select all text objects containing the specified character?

  Is there a way to select all text objects containing the specified character?

  For example,.

  My work consists of points and numbers.

  Points are separated into blocks of text, so are numbers.

  I want to select all points, so I group.

  Or numbers and group together them.

  

  Yes,

  -loop through all the elements of text

  -get each content

  -compare to '. '.

  -If the matching, save a reference to that block of text

  -When does with all frames

  -loop through all stored references and move to a group

• How to specify if a location of the object with the margin explicitly?

  In CS4 (I don't know what on CS5)

  We have problems when, after deleting or adding pages with items especially near the borders of the page. And we want to explicitly specify objects if they are from the margin, or on the page despite their location and without technical way to anchored objects.
  

  First, create a file with three pages and make the inside margin wider than the margin as in the screenshot above.

  Next, create two objects:

  black background extends to almost spine.

  a block of text for title text and the white body.

  

  Remove the page number 2.

  Then you see the black background output pages related (because it is from the margin before deleting).

  So far, everything is good.

  

  Insert a page before the page 3 again

  The black background now has different location from the original one. (Why) I'll tell you.

  Because the object was compared to the margin before delete page 2 and become compared to the page after deletion.

  So I suggest that if there is a possibility to restrict a location of object to be compared to the margin or page although if he leave page borders or not. you want to add options in the transform Panel:

  

  If these two options are not checked, then it will be depend on the location as the technique these days in CS4.

  I use anchored objects to specify the location of a logo, an image or a background color using object styles. It is therefore possible to change their position through multiple documents with a single click. The only thing I want, is to insert the object embedded in a block of invisible text.

• Trouble when not specify the HTTP port

  Hey all,.
  
  I'm trying to install JRUN4/IIS and deploy a web application that accesses servlets. I'm fairly positive that almost everything is set up very well because the servlet needs out of XML, however, I get a 404 error, if I DO NOT specify the HTTP port that uses the server - for example, my server is called frank and i've got things configured so that newsite.here.com translates into frank and things pull his IIS. Long story short, I can get out of my servlet if I specify the HTTP port that it is using such as:
  
  http://NewSite.here.com:8303 / htmlcontent.View
  
  However if I access it as:
  
  http://NewSite.here.com/htmlcontent.view
  
  In addition, newsite.here.com should resolve correctly because there are several other pages JSP/etc I can access this site.
  
  Can someone point me in a direction to look? Thank you.

  Did you run the web server configuration tool (wsconfig.exe)? See http://livedocs.macromedia.com/jrun/4/Installing_JRun/servconf.htm.

  Ted Zimmerman

• Objects of scheme of access without having to specify the user.

  I just created a role in a scheme and assigned to certain privileges. Then, I created a user and granted the role to him. But as the newly created user is not the owner of the schema when I say a query select simle like this:
  
  SELECT EMLOYEENAME FROM EMPLOYEES
  
  I get the error "table or view does not exist. Is there a way I can wirte to refer to objects in this schema without having to identify the owner. For example, instead of writing to SCOTUS. I want to write just the EMPLOYEES EMPLOYEES.

  >
  So, I create SYNONYMS for all objects in the right of the schema? And also, I have to use these synonyms in all procedures, functions and views rather than their real names?
  >
  Yes, if the procedures are not owned by the user who owns objects.
  A procedure created by SCOTT didn't need to use the synonym to access the objects belonging to SCOTT.

  Then, if you issue

  GRANT EXECUTE ON scottProcedure1 TO DAVID
  

  Then the user DAVID can perform the Procedure1 scott without the need to have privileges on scott objects used by the procedure.

     EXEC SCOTT.PROCEDURE1;
  

  DAVID must use the schema to perform the procedure, unless you create a synonym for the procedure.

• Cannot send Messages in the other e-mail account in the Mail of Microsoft Surface app

  I'm trying to set up a different e-mail account on my PC of Microsoft Surface in the Mail application.  Initially, I got the message ' to use this account, you must install a digital certificate on this pc... ».  I managed to fix that by disabling the "Server requires SSL" for both the incoming and outgoing server, which also changed the number of outgoing port 465 to 25.

  However, even though my account is now populated with and receive messages, I can't send all e-mail messages.  They just stay in my Outbox and the message " is not available" appears briefly in the upper right corner.  I've fiddled with the account settings (like changing the port to 587) but its made no difference.

  How can I get other outside e-mail accounts of my @outlook.com to work in the Mail application?

  I was able to find a configuration that worked:

  Incoming mail server: put your mail server normal but specify port 143 for Imap

  Uncheck the incoming SSL

  Outgoing mail server: put your mail server normal but enter the port 587 for Imap

  Uncheck the outgoing SSL

  Uncheck the box outgoing server requires authentication. (because Mail first checks the email, your server will allow you to send an email)

  After this configuration, save it, and then come back to check, since the first time I did it, he returned some settings, but after switching between them, it was ok.

  After doing this, messages have been sent and no more will not questions. I hope this helps.