Make an executable with DAQmx

Similar Questions

• Problems to make an executable VI from a DLL

  Hi people,

  I have 2 of the DLL, the first (rfid.dll) is imported into labview and contains some 55 functions. 1 of them has an internal memory management and too complex to work properly. So I have a second (wrapper.dll) dll that contains a simplified access to memory. However, on the second dll import, I get

  No executable VI
  The VI is not executable for one of the following reasons:
  1. the shared or a file-dependent library is not installed. To make the executable VI, you must install the shared library and all files supported on the computer on which you run the VI.
  2. a required custom control may be empty or cannot be found. To make the executable VI, manually update the custom control.
  3. the VI contains a parameter with an unsupported data type. To make the executable VI, you must replace the cluster indicator or empty the wizard generates a control that uses the data types supported.
  Retrieve attached RFID Radio list Wapper.vi
  test.VI

  Note that test.vi is not either executable, if I test function in the second dll, then test.vi is executable. It would seem that the second dll is unable to locate the rfid.dll.

  Any help please.

  Robert

  It seems that labview can solve the DLL using the DLL using the DLL

  My first rfid.dll used 2 other DLL that were in the path given, that has been resolved and I was able to import.

  The second wrapper.dll used the rfid.dll and it appears that the produced DLL in the same way, that he was unable to go to the next level.

  I fixed it by copying all the DLL in that I needed

  C:\Program NIUninstaller Instruments\LabVIEW xxxx

• Timing embedded with Daqmx on PCI-6132

  Hello

  My colleague and I are trying to make a program Labview which starts a timer when the first trigger (sensor) is struck and stop the timer when the second trigger (sensor) is reached in 2012. We currently have a program for her, but this program was not sufficiently precise. Also the current program is using the DAQ assistant, but we would like to replace with daqmx triggering. We have also tried to use the OnboardClock on the PCI-6132, but still could not do the work programme.

  Is there anyone who knows how to do this and could explain it?

  (In the attachment is the current program)

  Thanks in advance,

  Tommy van Geest

  Hello Tommy.

  You can share your current code?

• LabVIEW executable with my VirtualBench

  Hello

  32-bit Teststand 2014

  32-bit Labview 2015.

  VirtualBench model NI VB-8012

  I created a Labview VI using the screws of VirtualBench. This VI takes a measure of voltage with the DMM.

  I created a file of sequence in Teststand. This file of sequence called the VI as the limit of Test to verify if the measure is included.

  I created a Labview graphical user interface, which calls the sequence file.

  I'm able to run my VI, sequence and GUI. It all works and I am able to make my measurement of the tension of the VirtualBench.

  Now, I want to make an executable for the end user. I have trouble with the VirtualBench during an executable. I created a project in labview and my GUI with the llb GUI has been added to the project. I built my executable and tried to run. The tracks of MISTLETOE, however, once I click on start to run my sequence file, I am prompted with an error (see attachment). The VI VirtualBench works normally, but not as an executable... Please help.

  Thank you

  After working with the support OR an answer has been found.

  I finished my executable running in debug mode. While the code worked, I was able to get an ERR(-17600) to my attached error message error code. They gave me the link below to try to solve my problem and it worked.

  http://digital.NI.com/public.nsf/allkb/9C9EE3A6F7695AB9862578F0006CBF0E

  Solution:
  Follow these steps to correct the error-17600 (sometimes the error-18002)

  1. Once you have generated your personalized user interface, TestExec.exe, open the project file in the LabVIEW Project Explorer and right click on the .exe file.
  2. Click Properties in the context window that appears.
  3. Click on the category of settings of the Source file on the left.
  4. Click any screws that you have added to the original project (under project at downtown records) and check the box to Rename this file during the generation and the beginning of the text add "UI_".
  5. Under project files, and then click the option of dependencies .
  6. Check the box to apply the prefix for all content items and add "UI_" in the text box.
  7. Build the project.

  Thank you all for your time and help

• When I return in a recorded video on windows movie maker, all executives went black and have a yellow warning marker.

  When I return in a project recently recorded on windows movie maker, all executives went black and have a yellow warning marker, the sound also went but the name of the track is always above executives

  Hi steveXB,

  1. did you of recent changes on the computer?

  2. this happens with all registered projects?

  3. you have any program installed on the computer for photo editing?

  I suggest that you disable video filters windows make of film and change, if that can help.

  Change the video filter settings

  http://Windows.Microsoft.com/en-us/Windows-XP/help/MovieMaker/change-video-filter-settings

  Windows Movie Maker: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Movie-Maker/FAQ

• make a video with individual images

  Hello

  I want to make a video with individual images.

  One of my computergames is able to take 25 frames per second (30, 40 etc.). The game records the images in a folder. For a minute, there are more than 1000 executives.

  Now, I need to know how I can tell After Effects that each 25 images are a seconds.

  I want to just make a film of this game. This will be the easiest way if After Effects can deal with these individual images.

  Is this possible? I'll be very happy if some can explain to me how to make my idea.

  Sincerely,

  RazooN

  Interpretation of the images and import preferences for the image.

  Mylenium

• How to make a ringtone with Itunes 12.4.2.4?

  I'm new with Iphone... I now have a 5 s.

  I have itunes 12.4.2.4

  How can I make a ringtone with a real song?

  Thank you

  go to AppleSupport

• I have a MacBook Pro 17 withProcessor - in 2.33 GHz Intel Core 2 Duo (circa 2007).  Running OS 10.7.5 (Lion).  Not compatible with the OS later.  Hardware can be upgraded to the latest processors and other components to make it compatible with the new OS

  I have a MacBook Pro 17 withProcessor - in 2.33 GHz Intel Core 2 Duo (circa 2007).  Running OS 10.7.5 (Lion).  System indicates the computer is not compatible with OS later.  Hardware can be upgraded to the latest processors and other components to make it compatible with the latest OS.  I think that later models of Macbook Pro 17-inch with processors that allow updates.  I was wondering if these can be swapped or if alternatives were available.

  Only the RAM and storage (HD, SSD) can be changed.  Everything is welded to the map logical and selected specially for the system configuration.

  I'm sorry.

• With a sampling of the data with DAQMX, error-200279 occurs when making 2d array dbl

  Hello

  I did a system of simple analog voltage with DAQMX data acquisition.

  It is made for reading of capacitance, where output capacitance value out of a circuit in the periodic voltage signal.

  What I want is to get data from four capacitors simultaneously through four channels, using samples n n (dbl 2d).

  The structure of my VI is almost similar with examples of continuous sampling of voltage in LabView, with the exception of a few other calculations in the loop.

  And for the synchronization of the trigger, I've corrected the edge of release with the external signal from the capacitance reading circuit.

  Version no. 1 has a channel for data input voltage. Version n ° 2 has four channels for the input data.

  While ver.1 can get accurate reading of four capacitors circuit data each (a single channel at a time),.

  ver.2 acquires four channels of data, with a single thin data channel, all the others were wrong.

  I saw a 200279 error occur in the DAQMX read part 2d dbl, so I tried increasing the buffers by changing the sampling frequency or the number of samples, but it wasn't everything.

  I rose for most of the forums with the 200279 error, but the solution would not work on mine.

  Anyone can find the problem? I will attach my screws it may include a bit of Korean language, but most of them are in English, shouldn't be too hard to recognize. Sorry for the inconvenience.

  Oh I forgot, my DAQ is NI USB-6259, and it works in Win XP sp3 and LabView 8.6.

  Thank you.

  Hello Azurenight,

  The 6259 is a DAQ card of the M Series Multiplexed, which means that it is not possible to sample each signal at the same instant, rather the channels are all sent through the ADC even and must be sampled in order. More information on this can be found here:

  LabVIEW Help: Multiplexing compared with simultaneous sampling

  http://zone.NI.com/reference/en-XX/help/370466W-01/mxcncpts/multisimulsamp/

  It may still be possible to get the data you need with the card you have - could you give more information about the maximum eligible period between samples on different channels?

  If you require * real * simultaneous sampling, you will probably need different hardware.

  Kind regards

• Is it time stamp with daqmx read

  Hi all

  Simple question.  I have currently not creating a task or starting a task, I simply create a channel and reading that chanel.

  It is...  Why I don't get a timestamp when you do and do I create a task to get one of this?

  There is a timestamp when you use the DAQ Assistant or when you choose to return a data type of waveform with DAQmx Read.

  You can't do a reading without a blemish. You don't have to create the task in MAX, however.

• Multitask with daqmx

  Hello

  I am currently working on a Senior design project where I have to measure rpm, torque, pressure and temperature.  I use strain gauges, pressure sensor and a Hall effect sensor, thermocouples for these readings.  A myDAQ collects readings rpm and pressure while a cDAQ collects couple and readings of the temperature with NI 9211 and NI 9237 modules.  I have created LabVIEW screws for each sensor and they work.  The problem I have is when I try to create a VI with DAQmx who reads all the values of these sensors simultaneously.  The VI I joined randomly displays one of the measures while other measures remain empty.  How can I change my VI so I can show all my readings at the same time?

  Yes.  Create multiple tasks, where all the strings that are common to a specific device are grouped in the same task.  Then go and run these tasks in parallel.  Do you need a precise synchronization between the tracks in the different devices?  If this isn't the case, then the method should work perfectly.  If you need a precise timing, things would get more complicated, but might not be impossible.

• time of release with daqmx

  Hello

  How can I set the time of liberation with DAQmx?

  In general, with a single DAQ hardware, the two signals are connected at the same time and the acquisition time is a function of the sampling frequency and number of samples read. For example, with a sampling rate of 1000 samples/s and 50 samples, the acquisition will be 50 msec. You then get a returned array if you wanted to watch a single signal by iteration of the while loop, it is simply a matter of indexing the specific channel to the table. You must set the mode of continuous sampling to avoid gaps and precise timing. Using two separate tasks and switching back and forth would add a lot of overhead to close/create tasks and you have little control over this period.

• 2009 with DAQmx Installer

  We distributed an integrated application that uses DAQmx 8.x and LabVIEW 8.6 for several years.  I'll call the application MyApp 2.8.  We are working on a new version that uses LV 2009 and DAQmx 9.x, which we will call 3.5 MyApp.  When build us and deploy a Setup program for MyApp 3.5, then try to use it on a computer that already has 2.8 installed MyApp, the installer complains about dependencies and said that the two DAQmx 8.x and MyApp 2.8 must be uninstalled first.  I spoke NOR cela briefly and told me that DAQmx 9 was a pretty radical overhaul that required this change.

  It's annoying and slow for us, but almost untenable for our customers.  First of all, MyApp MyApp 3.5 and 2.8 are compatible, and we prefer to leave MyApp 2.8 installed as a backup as people get used to 3.5.  If the customer needs:
  Uninstall MyApp 2.8

  Uninstall DAQmx 8.9

  Install MyApp 3.5 with DAQmx 9.0

  Reinstall 2.8 MyApp (as if they can still find the disc!)

  Far too many steps and complications.  In addition, it is not really necessary.  If the runtime for 2009 is already installed on the computer (for some reason any), you can simply copy the MyApp 3.5 on the computer and it will run with DAQmx 8.9.  But this only postpones the problem, because at some point the customer will upgrade once again, and we will have forgotten that they were installed with a workaround, and...

  The really frustrating part is setup for MyApp 3.5 refuses to install until MyApp 2.8 is uninstalled.   While we have proven that MyApp 2.8 will work very well with DAQmx 9.0.

  Is anyone else noticing this problem?  Has anyone found any better workaround?  Is the same problem when we jumped 2009 and returned with 2010 and the last DAQmx?

  Thank you

  DaveT

  DaveT,

  You're right - for this aspect of the problem - my proposed solution won't help. At the price of a larger Setup program, including the full version of DAQmx probably will give the upgrade experience you want. If the web download size is a concern, perhaps you could provide two builds of your product - with the acquisition of complete data (for those of you who have your old product) and with smaller data acquisition (for those who do a clean install)?

  In addition, certain registry keys to remove the dependency I guess hacking is sort of an option, but it probably isn't the type of solution you are looking for. (We are currently researching the addition of some extra features in the uninstall program OR allow without taking account of certain dependencies, but nothing is currently available).

  Kind regards

  -WesW

• My camera Olympus only works with Apple's Quick Time 7. Is it possible to make it work with my operating system from Windows XP?

  My camera Olympus only works with Apple's Quick Time 7.  Is it possible to make it work with my operating system from Windows XP?

  Apple QuickTime 7 works is because. MOV is the Apple
  QuickTime format.

  QuickTime. MOV files can cause problems with Windows Media Player.
  And... If you plan to try editing with Movie Maker... the files should
  be converted to the. WMV format.

  No guarantee, but the following decoder might allow Windows Media
  Reader to read your. MOV files. Only problem is... it is not freeware to retail.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  3ivx MPEG-4 5.0.4 decoder
  http://store.3ivx.com/3ivxStore/product_details.php?ID=11

  Convert the. MOV files to the. WMV format may be worth a try:

  There are many converters available on the net... some
  free... some detail.

  The following freeware converter is just one example:

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  Format Factory (freeware)
  http://www.videohelp.com/tools/Format_Factory
  (the 'direct link' is faster download)
  (the file you want to download is: > FFSetup295.zip<>
  (FWIW... installation..., you can uncheck
  ('all' boxes on the final screens)
  (Windows XP / Vista / 7)

  First, you will need to decompress the file or just open the
  Drag > FFSetup295.exe< out="" of="" the="">
  and drop it on your desktop. To install left click.

  Next, after the download and installation of Format
  Factory... you can open the program and
  left click on the toolbar, the "Option" button and
  "Select an output folder to" / apply / OK.
  (this is where you find your files after they)
  are converted)

  Drag and drop your video clips on the main screen...

  Select "all to WMV" / OK...

  Click on... Beginning... in the toolbar...

  That should do it...

  Good luck

• When I publish my movie in movie maker, he publishes with a split screen, how to fix this?

  When I publish my movie finalized in movie maker, it ends with a split screen, half top is my film and the lower half is green screen... What I am doing wrong?

  The info... copied on the net... may be worth a visit:

  =====

  The Green problem bar setting in Windows Movie Maker
  http://www.bernzilla.com/item.php?id=884

  When I tried to follow the directions, I was unable to find XVid on my
  computer.  So I googled XVid and then (I think) the 2nd entrance to
  Download XVid.  After I downloaded it, I could follow the directions
  bernzilla and when I published a video - Voila! no green bar!

  After thick film Green line is published
  http://www.windowsmoviemakers.NET/forums/ShowPost.aspx?PostID=105025

  Good luck...

  =====

  No guarantee, but it might be interesting to try to publish your
  project in DV - AVI format to a folder on your hard drive and
  then import the file .avi in DVD Maker to create a DVD.

  (The following links should help explain how to record in DV - AVI)

  This image shows where the DV - AVI option.
  http://www.Papajohn.org/IMGs/Vista-PublishToComputerChoices.jpg

  Windows Vista - publish a movie in Windows Movie Maker
  http://Windows.Microsoft.com/en-us/Windows-Vista/publish-a-movie-in-Windows-Movie-Maker

  Movie Maker Vista - profiles Publishing / qualities
  http://www.Papajohn.org/Vista-publishing.html

  Windows Vista - Windows DVD Maker - burn video disc
  http://Windows.Microsoft.com/en-us/Windows-Vista/burn-a-DVD-video-disc

  Windows Vista - DVD - video burning - frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/DVD-Video-burning-frequently-asked-questions