Manufacturing possessed 6 s calls on its own...

My iphone 6 s has been calling of numbers in my address book randomly and not hot. I installed everything at the time of the new update and I hope it helps anyone else having this problem? If so, is there a solution? The battery life seems also shorter than it should be...

THX LH1207

If this happens when the phone is not connected to you a bad table digitizer. Take it to an Apple store and they will replace the screen or phone. But as it is under warranty, it should make no difference what they do.

Tags: iPhone

Similar Questions

  • selectingitems and trackpad pointer moves its own

    I was watching a video of Amazon and may have struck a couple of keys, or my hand slipped in the keys - I don't know, but pointer froze on the follow-up to the film bar at the bottom of the screen (not sure if this is relevant, or what is called in fact this bar) in all cases, the pointer froze and then began to move erratically in bursts on the screen , selection of apps, ibooks, photos, etc. and then OPEN them as if I had clicked. Literally goes haywire as if it had a life of its own. I have NEVER experienced this during the 11 years that I've had the Mac laptop. I don't know if trackpads wear out (my current MacBook Pro is a vintage 2012 and I debated update, but it was working very well.) I wonder how to clean the dust/debris under keys because I know it can be done and I was wondering if something got under the trackpad (seems pulled by the hair) but it's really another question for me to continue. Any help on trackpad possessed pointer would be appreciated. I don't see that this issue anywhere else... - Pam

    Remove the bottom plate and inspect the inside.  Pay attention to the battery to see if there are signs of expansion.  If so, take it out and have a new installed.  An extended battery can affect the trackpad.

    If no success, make an appointment at an Apple store genius bar for a FREE evaluation.

    Ciao.

  • Why my iMessages are showing on my camera of husband? It has its own Apple ID?

    Why my iMessages are appearing on my husband's phone? It has its own Apple ID.

    Ano also its (incoming and outgoing) calls on iPhone 6Plus S show on his iPhone 6s.

    Thank you

    Apparently, both phones have been implemented with the same iCloud account.

  • Does anyone else have an iMac that starts typing on its own?

    I try to type a password and the computer just starts typing, indefinitely. I'll write an email and the computer hits back again and again and again. Then it starts to beep me - the beep that says: "has already hit this key! I have no control over what he types. My only recourse is to restart, which works most of the time. Until yesterday.

    This goes on 5 months patiently trying a bunch of solutions, none worked. Of course, it produced intermittently, making it much more difficult.  However I called and talked to a counselor while he was hoping it would help. Nope.

    I went through 5-6 people from Apple for probably 7 + hours on the phone. Finally, they said make a genius bar appt and bring it in. Yes, I did. The whole darn 27 "thing. They gave me a new keyboard to try. Nope. They suggested I have reinstall the latest system. Yes, I did. Nope.

    I'm getting pretty well supplied upward.

    I will say, in all the conversations I've had, I'm pinned a rude woman. Each representative was pleasant and everyone has, according to me, tried very hard to make it work.

    Unfortunately the last woman I spoke with, a Counsellor who gave me his phone number and extension, did not return either my emails, nor my phone messages.

    So I'm screwed out of. When he arrives, of course, I can't use my machine $2000 +. Fortunately, I have a laptop or I would scream bloody murder. Maybe I need to start screaming bloody murder. I want that they fix it or give me a new. 5 months is enough.

    Someone else has a computer that writes on its own? Of course, I'd advice anyone can offer.

    I've had this happen a couple of weeks - except that it was on my end 2012, Mac Mini, on which I had just done a clean install of El Capitan.  The Mac Mini was using the Apple bluetooth - like the iMac keyboard.

    I've only had the question on the login screen - it would just start repeatedly typing in the password field.  To solve - and to see if was indeed a problem with the keyboard - I went to a wired keyboard - and the problem stopped.  This little told me it was the keyboard.  To troubleshoot further - I happened to have a spare identical keyboard - so I have the bluetooth of the iMac keyboard odd and not matched the keyboard problem of the Mac Mini.  I paired the keyboard blue tooth with the Mac Mini iMac and paired the bluetooth problem with the iMac keyboard.  I did a reset SMC, PRAM/NVRAM reset and start secure on the iMac and Mac Mini (precaution).  The problem never happened again.  I was not yet the keyboards of return - and it has been a few weeks.  If you do not have a wired keyboard or bluetooth spare parts - you could try the following:

    1 turn off your iMac keyboard pairing.

    2. join your iMac keyboard

    3 stop the iMac

    4 perform a SMC reset (iMac, you delete all the devices to the iMac - unplug the power cord at the back of the iMac.)  Wait at least 15 seconds.  Reattach the power cord to the iMac.  Wait at least 5 seconds.  Press the button.

    5. when the iMac restarts - stop it again.

    6 reset the PRAM (memory NVRAM) - by simultaneously pressing the keys CMD OPTION P and R, after hearing the boot chime.  Keep hold the keys until you hear the chime again.  Then keep hold the keys down until you hear one more chime.  Release the keys - let the iMac start.

    7 judgment of the iMac, once again.

    8. perform a startup by holding down the left SHIFT key when you hear the boot chime.  Now keep the left SHIFT key until you see the progress during the start bar.  On the login screen - it should be a message from Red starting at the top right of the screen.  Allow the iMac to sit at the display of connection for 5 minutes.  Connect to iMac - (it will be slower than normal).  Allow the iMac to sit to the desktop for about 5 minutes - do not run all the apps.  After 5 minutes - stop the iMac.

    9 start the iMac and Note If the keyboard is no longer slap on its own.

    ~ Scott

  • My Cliq close on its own

    My cliq turns off on its own, it was in my jacket pocket down with the set screen time-out, so maybe that it overheated? TMobile said this is not listed as a function and have no info on an automatic stop for heating.

    If you look carefully at the top of your phone screen where the M symbol is and below the slot of the ear are sensors. One of them is a proximity sensor which detects when your face is near the phone turns off the light on the screen. If your fingers are close to him by answering a call, it can cause this to happen. Next time try to keep your fingers up to the front of the phone and see if that fixes it. Let me know.

  • Target RT Apply network settings: an its own adjustable cRIO IP address...

    Was looking for a way to port 1 IP address of a target it cRIO setting ' self - progammatically

    (1) without having to know that delivered such intellectual property

    (2) and without having to know as shipped MAC ID

    Get info target works very well with the loopback address so I undbundle the MAC ID and use it to apply settings target. What mistakes on 56.

    NI_Real-Time Libraries.lvlib:FPC Discover systems (all interfaces).vi
    
    Complete call chain:
         NI_Real-Time Libraries.lvlib:FPC Discover systems (all interfaces).vi
         NI_Real-Time Libraries.lvlib:SetTargetConfig.vi
         NI_Real-Time Libraries.lvlib:RT Apply Target Network Settings (Static).vi:1
         TargetInfoTest.vi
    

    Apply works very well when I provide the MAC ID of the target, then run it on the development computer. But I was trying to avoid having to save the MAC ID.

    I wanted to have all cRIO it's own initialization IP address - and retrieve the address of a file of gxml.

    Is this possible?

    Hello

    If you look at the second link I posted, it talking about going into the .ini file and change the IP address it. I think this method could be made of the cRIO itself; However, in general, we recommend having the cRIO put its own ip address. I guess that's why the error 'Apply network settings' VI. The cRIO having set its own IP address can be problematic if it is attached to something that the computer is unable to find. Good luck!

  • LaserJet 5 PCL Overlay Macro is not 'Overlay', on its own Page impressions

    Hello!  I wrote a macro of overlay PCL.  It contains the PCL and HP-GL/2 commands to draw a shape of statement.  I tried to call the shape on a LaserJet 5 times as automatic overlay and a macro called, but whether I invoke it, filling data print on its own page, followed by a page, print out the form.  I need them to print on the same page together.

    Here's how I'm trying to run it on the command line WinXPSP3, copy the macro and data to the print server LJ5:

    copy macro.txt + filldata.txt \\ps-70ac4a\p1

    I tried to post here macro.txt and filldata.txt, but the HTML form will not let me.

    You can obtain them in ftp tatlow.com, A1234567, A1234567 password username.

    Anyone see what I'm doing wrong?  Thank you!!

    >> ... But with filling multi-page data, only the first page of data to fill overlay; the following pages have no overlap.

    >> ... (Each page in filldata.txt ends with a page break, hexagonal 0C).

    >> ... If you could please take a glance over, I put the new macro.txt and a new filldata.txt of 2 pages...

    I concatenated the two files into a single file and sent the contents of this file (using 'lpr') to the network port on my printer (alone) (LaserJet 1320n).

    Two pages are printed, both with the overlay.

    Like I can't reproduce your symptoms, I don't think that I can try realistically investigate the cause of your problem.

    {I would remove the CarriageReturn character and line break (0 x0d0a) that occur just before the escape sequence "return to PCL", because it is (strictly) should not in HP-GL/2 mode.]}

    The tool used to analyze the print file is the PRN file analysis tool in paraphernalia PCL app, available via http://www.pclparaphernalia.eu

  • Xperia Z3 Compact - phone turns off on its own after lolipop update

    Team dear Sony,

    Reminder: My Xperia Z3 phone is 5 months old. It worked perfectly well until the update of Lolipop (updated 3-4 weeks).

    Question: Phone turns off suddenly on its own and is not put on until several attempts after pressing the power button.

    Few comments:

    1. no point it disables. During a call, while loading, while the navigation and so on.

    2. I tired of all the combinations of power of the device mentioned in different threads.

    3. I removed the SD CARD, SIM CARD. But in vain.

    4. as someone mentioned in one of the thread suspecting some sort of application creating the question, I did mode ultra endurance enabled to limit the minimum demands naked ot. But in vain.

    5. I did factory reset and update the phone. But in vain.

    All effrots are frutail.

    Can the team Sony or friends on this forum to support suggest me what to do?

    Thank you in advace,

    Gopi Krishna

    @GopiKrsna

    Try this.

    Remove the SD and SIM cards > fix the phone with PCC > make sure you delete all > when you repair the phone > trying to use the phone without SIM and SD card for an hour or two > report.

  • I need to connect a card its own irq.

    OK, it's really simple.  I have a PCI firewire 400 having IRQ conflicts and forcing my external audio interface to stop working.

    This CANNOT happen.  I do not what else is this card must have its own IRQ - IRQ sharing.  period.

    switching of the PCI slots has not worked.  turn off nonessential hardware in Device Manager has failed.

    I could manually IRQ in all previous versions of windows.  How can I do this on vista?

    Hello ikediggety,

    There are ways with which you will be able to assign the IRQ in Windows Vista. However, it requires editing the registry and is not a recommended solution. Editing registry without an indication of the manufacturer could be dangerous. If there is real device conflicts, Windows 7 allows you to change the IRQ resources in Device Manager. But you don't have that sharing legitimate, conflict.

    It involves registry IRQ priority creating. There are several third-party Forums talking.

    I suggest that you search using your favorite search engine if you understand the risk and want to do it again.

    I suggest that you connect it to a different PCI slot and if it continues to come into conflict, it would be a hardware problem. I suggest that replace you it with a USB port.

    I hope this information helps.

    Thank you
    Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

  • my laptop stops on its own

    recently, I downloaded some games from mostfun.com and everything was perfect for about a week, then my computer just started blocking down on its own and incidentally I don't get error down and all just poof, he's going he first flicker a small last thing so far it's just when I know im running one of the games or a movie I downloaded the logical thing in East to remove these i I want to just make sure that its not something else

    It seems that the laptop may be overheating.  Are you sure there is enough air past for laptop?  Make sure that it is on a flat surface, with nothing to obstruct the ventilation openings.  Make sure that the vents and fans and heat sinks are free from dust - examine their blowing with compressed air (power of the system first, of course).  Depending on the laptop model, it may be relatively easy to blow off the dust with compressed air, or otherwise clean up things a bit.   Fans should be kept up well - only no right turn when being ripped off.  My Dell laptop has a removable fan (two small screws need to be removed) that can easily be blown.  This also allows access to the fins of the heatsink.

    Some laptops also have a removable filter that traps the dust and must be regularly inspected and cleaned.

    Are all the BIOS settings for the adjustment of the temperature, the value lower than the manufacturer's recommendations and the default values (you need to check the manual of your laptop for this).  Also make sure you run the latest version of BIOS (again, the manual of your laptop would have the details; the manufacturer's website should also have this information).

  • Screen ACL in Windows 7 towers / turns off in 1 or 2 minutes on its own

    Strange problem started recently. My computer laptop LCD screen turns off in 1 or 2 minutes on its own even to power cable. I checked and have already reset all power plans, but the screen seems to stop on its own. I was not able to understand the problem.

    Also changes to the power management has no effect on this behavior. For example if I increase the delay before the screen stops at 10 minutes (with or without battery) it always closes the screen in 1 or 2 minutes

    Can you please suggest what could be the problem.

    I have an Intel Core 2 duo processor - x 64-HP DV4t laptop

    Thank you

    Varun

    Varun

    Hi Varun,

    ·        This happens to you while you use a particular program or are the random problem?

    I think it is a hardware problem and you may need to contact the manufacturer of the laptop computer for further assistance.

    In addition, uninstall any software of management of power given by the manufacturer and check.

    Uninstall or change a program

    http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

    Hope this information is useful.

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Windows 7 stops on its own without warning

    My pc running windows 7 Home premium keeps stopping on its own without warning - I checked and its not overheating there are a lot of ventilation. I was told that it may be registry settings but don't see why I should pay for a reg cleaner because I do not know if it will solve this problem

    A Reg cleaner will cause more problems than it will fix. If the PC stops while using it, then see the test below tools. If it stops while his idle then you will need to check and change your power plan.

    First try running Memtest86 +, that runs from a floppy disk or CD and should eliminate or
    confirm whether your one or more of your sticks of memory are bad or the values of the SPD in the BIOS are correct.
    Let it run for as long as you can: 2,4,6,8 or several hours, so no errors at that time then your ram is OK.
    http://www.memtest.org/
    Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
    http://www.overclockers.com/forums/showthread.php?t=409152

    Device drivers: have you installed latest drivers from device of the manufacture of the motherboard? Visit their site to support for the latest drivers as the CD that came with the motherboard may have older less stable drivers.

    Check the download site of the manufacture of the graphics card for the latest Windows 7 drivers for your card.
    Discover also Nvidia 'Smoke' test or equivalent ATI.
    ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
    NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

    Prime 95:
    http://www.Mersenne.org/freesoft/
    It's a stand alone .exe file contained in an archive .zip.
    Simply choose to run the 'stress test' option for 3 hours or more.
    If your PC can pass this test, your memory and CPU
    are very good (close the housing cover in order to maintain adequate ventilation)

    Core Temp:
    The temperature of each core of the processor.
    For overclockers using stock Intel/AMD radiator and cooling fan
    You can expect temperatures of 35 to 40 ° C in idle and 60 to 65 c max when running Prime95
    http://www.alcpu.com/CoreTemp/

    CPU ID (CPUZ):
    Watch the clock speed of the CPU under various conditions of loading
    (when using speed step technology Intel EIST).
    Also has two tabs (memory and SPD) that indicates the actual speed of the memory
    and 'SPD' tab displays the nominal speeds for each memory location that is filled.
    http://www.CPUID.com/cpuz.php

    Hard drive test - CD Bootable:
    If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools (bootable CD) and check bad sectors:
    http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRD
    For Western Digital disks using WdDiag: http://support.wdc.com/product/download.asp?lang=en
    Fujitsu utilities: http://www.fujitsu.com/us/services/computing/storage/hdd/support/utilities.html
    Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
    Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT

    JS
    http://www.PAGESTART.com

    Never be afraid to ask. This forum has some of the best people in the world to help.

  • Cursor moves on its own

    Periodically, my cursor moves on its own and has been a problem for a few weeks now.

    Initially, he started with the built-in cursor not only movement erratic but also stuck in place on the right side to her screen/only up and down. To try to solve this problem, I started using a USB mouse to see that the problem persisted except that I've been able to move the cursor on the screen even though it move independently (by clicking on the icons and other, however, continued to be difficult).

    It feels like this question started out not the case.

    Here's what I tried to solve the problem (takes the chips of another user and added on):

    Change of mouse did not help (the problem persisted with USB mouse and wireless with new batteries in wireless)

    * The mouse software update did not help

    * Move the mouse or its sender to another USB port wireless did not help

    * Restore the computer to a restore point of verified (2 weeks ago) before the problems started never did not help

    * Reset did not help

    * Turn off an extended display and performing a single monitor (or the other) did not help

    Pointing device settings change of rather fast for its slow response seems to have it actually move slightly slower, but it has not solved the problem and the rest largely unusable a lot of the time.

    * To control the cursor in safe mode (works fine)

    * Done a virus scan (computer is clean)

    * Made a clean boot

    * Ran troubleshoot on built-in cursor and mouse USB (or came with all the problems)

    * Check properties on devices and the results say that the two are "works properly."

    * Uninstalled and reinstalled the program for the device

    Any help is greatly appreciated!

    Hi J Clark,

    We appreciate the steps you have taken and thank you for the information provided.

    It seems that the mouse works in safe mode and it could be one of the engines is at the origin of the conflict. We will analyze and identify the cause of the problem.

    Which antivirus program is installed on the computer?

    You can open the Task Manager and monitor all programs running in the background when the mouse movement.

    Are you aware of changes to the computer in these two weeks mentioned?

    I suggest you to update display drivers by visiting the computer manufacturer's website and check the results. Also install all updates through Windows Update.

    See the links below for more details:
     
     

    Update drivers: recommended links
    http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

    You can also scan SFC to check if there is any corrupt system files.

    Use the System File Checker tool to repair missing or corrupted system files

    http://support.Microsoft.com/kb/929833/en-us

    Hope this information helps. Response with status so that we can help you.

  • QHMPL wireless Comboa Qhm9440 rotates 90 degrees to the right on its own.

    Original title: My Wireless mouse just turned 90 degrees to the right on its own and now I can't seem to fix the problem. Help, please.

    I use a qhm9440 of QHMPL wireless Comboa with windows 7 ultimate. The direction of mouse just turned 90 degrees clockwaise on its own, and now I can't seem to return to normal. I tried to re install the drivers and do a system restore, but nothing works. Help, please.

    Hello

    It seems that some setting needs to be changed for the mouse.

    Since you have already tried to reinstall the drivers and made the restoration of the system, I suggest you contact the manufacturer of the mouse to get help.

    QHMPL Support

    Hope the helps of information.

    Let us know if you need help with Windows related issues. We will be happy to help you.

  • Why can I I have more docs multiple open with each having its own framework?

    used to be I could have multiple PS files open at the same time -each with its own framework ('frame' is what I call the stuff on each side of the image - toolbar on the left, layers, etc. on the right).  I had to reinstall all of the program recently, and since I could not get this configuration.  best I can do is floating windows, which is so difficult to work with, as often, I drag one doc to the other stuff.  I hope you can help!

    PS. using cs 6 on mac os 10.11.3

    Window > arrange > consolidate all to tabs.

    Use the "F" key to scroll through the three display modes

Maybe you are looking for