material missing triggers hdio? (PFI0)

Similar Questions

• Missing triggers on 5122

  Hi all

  I have a system composed of 2 5122 PCI cards that I try to sync.  What I want to do is to use a trigger to edge for the acquisition on a single card and then use this acquisition to trigger to trigger the same Member of the Council.  I export the trigger signal using a cable RTSI connecting two boards (one that I built myself using two connectors 34 pins and cable in standard tablecloth; maybe that's the problem ).  This configuration works very well when I apply a wave with a frequency below 100 Hz; However, when I go on this frequency, the jury of the slave seems to be consistently missing triggers.  It's not clear to me if the signal is not exported or if the second bedroom is simply not catch them.  We need this to be able to operate as soon as possible.  Does anyone have any suggestions?

  Peace, Matt

  Thanks, Efrain.  I was about to post on this. (By the way, where are the RTSI "necessary specifications"?)

  It turns out that the problem was not the RTSI cable - works very well (it was built using standard ribbon cable and connectors 34 pins).  On the contrary, the problem is in order.  I arm myself relaxing on the slave card after that I started the acquisition on the master (duh!).  This means that for signals with frequencies low (for example, 10 to 100 Hz), there was a good likelihood that the trigger be armed before a signal has been sent.  However, for signals at higher rates, the trigger was often lost as it was armed after that the signal has been sent.  It was problematic because I would always check to see if the acquisition was complete on two cards before rearmament and the acquisition again.  I thought it was something simple like that, but somehow when I looked at the beginning, I thought that the logic was right.  That's life.

  Peace, Matt

• Wireless Internet material missing

  I have trouble with my windows XP and my computer would no longer start. I just reinstalled XP Professional and it works fine now. problem is that I can't connect to the internet, as the wireless option is unnavailable, only LAN. until I reinstalled windows, the wireless icon was always at the bottom right near the clock. also missing is the webcam too is built in.

  totally confused. all I can think is that I have to buy a usb to wireless gadget, although it seems like unnesesary the wireless is in my laptop somewhere.

  I use an acer aspire 5100 laptop if this is of any help.

  any help would be greatly appreciated :)

  After you install Windows XP, you must visit the Acer site, specific to your model and install the Windows XP drivers for your system, you do NOT install them of MSUpdate

• 17 t-j100 Bond in movement: the drivers missing (jump movement 17 t-j100 on windows 7), problems with their installers

  Hello

  I have recently reinstalled windows 7 on my hp laptop.  in Device Manager, the following hardware ID must still pilots. :

  ACPI\HPQ6007

  ACPI\INT33A0

  When I search on google, I understand that one needs a processor (AMD)? Driver USB 3.0 and the needs of second intel smart connect pilot.

  When I try to install the chip intel connect driver, SP64964, I get an error message 'access denied '.  I get this same error message when I right click and open the installer with administrative privileges.  Why is this settled?

  the host usb 3.0 driver I installed, SP64965, installed correctly, but she let this ID (INT33A0) material missing.  It remains an "unknown device" in Device Manager.  How to solve this. ?

  Thanks for any help you can provide.

  Hello

  The first hardware id is for HP 3D DriveGuard on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67280.exe

  For the ISCT driver, try the version directly from Intel on the link below.

  https://Downloadcenter.Intel.com/download/23109/Intel-Smart-Connect-technology

  Kind regards

  DP - K

• MAX how to acquire data only on hardware triggers?

  Hey,.

  I need to use the card pci-6224 daq material being triggered. Here's what I did: -.

  (1) I put these settings in the configuration affecting changed my acquisition mode 1 sample (timed HW) and set the rate at KHz

  (2) the digital edge trigger type, my pfi pin and the whole edge to edge down

  and here is what it does Max awaits the first impulse before data acquisition and after the first impulse, he always keeps the information even in the absence of triggers. I used an oscilloscope to see if I was generating pulses in my pfi of entry but there is no generated impulses.

  So I was wondering if someone could tell me a few reasons as to why MAX keeps getting data after the initial outbreak?

  Thank you

  MUGA,

  To make an acquisition redeclenchables, we need to set a property that we do not have access to directly to MAX (redeclenchables true parameter). However, based on what you have explained, it's pretty simple applications you meet. The best way to proceed is to simply use your trigger as an external sample clock signal. Using this trigger as the sample clock signal, you will take only sampling points on the edges of this signal trigger regardless of the trigger parameters.  So, I simply specify this signal as your external sample clock and go from there.

  Timothy

• Speaker problems on I phone 6

  My phone I have 6 was originally blocked on the headset mode. However, I cleaned the plug of the listener with a q tip that seems to have taken off headset mode. The problem I have now is that during phone calls my voice vibrate and may not be heard by the other person when you call. I have only heard when it is on the speaker. Help, please.

  Hello Banjo7,

  Thank you for reaching out to the Community Support from Apple. I know how it is important to be able to make calls reliably, so I'll do everything I can to help and get your phone works as expected. It sounds like you were on the right track with the headphone of cleaning, it is possible, there is debris still in decision-making that makes contact with the material that triggers the phone looking for an external Microphone. Before get us too far though, go ahead and reboot the iPhone just to be sure it is not hooked on this mode.

  If you have canned air as the type that is used to clean computer keyboards you can have the cleaning with this chance, and there is little risk of damaging anything with this method. If the problem persists you can contact your local Apple retail store or authorized, service provider you can find here:find

  If you experience problems or have questions, the entire community is here to help.

  -Best regards-

• Tecra R840 not stopped after waking from sleep (USB, BT does not work)

  Hello

  I have a problem with my R840 running win7pro + SSD.

  After he wakes up from his sleep:

  -No USB activity (but there is power in ports because I can see the leds on the external HARD drive or mouse)
  -my Bluetooth mouse no longer works
  -my internet connection will work after 1 or 2 minutes of waiting
  - and... the laptop will not be stopped, unless I press the physical button on / off for 5 seconds or so!

  In Device Manager, everything looks ok! In all power management devices/REPEATER MULTIPORT USB etc is on do not turn off the devices to save energy!

  Already own started the laptop several times and the problem remains.

  Everything is fine if the laptop can't SLEEP!
  But I put it in sleep mode and I wake up it I have all these problems!

  Any suggestions?

  Best regards
  Paulo

  I think it of very difficult to find a solution to this problem because the software (OS) and hardware (SSD) has been changed.

  So the question could appear due to new software and change of material missing or bad drivers.
  To me, it seems that the issue requires further investigation.

  Did you notice the same problems using the preinstalled Toshiba system and the original HARD drive?
  I think that this should be checked first.

  By the way: this is the BIOS updated?

• HP elitebook 2540p: I can not find drivers for Windows 10 hp elitebook 2540p

  I have a hp elitebook 2540p with an i7 L640 intel SSD 160 GB corsair 8 GB of ram and windows 7 64-bit.

  I would like to upgrade to 10 64-bit windows, but I can't find compatible drivers. I tried to update but the touchpad was not recognized by windows, the tactile bar does not work well, and I have not found one driver other than the video card driver.

  I would like to know if there are drivers that are compatible with my laptop for Windows 64-bit 10.

  Thank you

  Hello

  Thanks for posting in the HP Support forum. Welcome!

  Officially, your computer does not support Windows 10 because it is an old model. Supported are only Windows XP, Vista and Windows 7.

  > > http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=4138317

  Windows 10 was created not even when Windows 10 has arrived.

  Although not officially supported, if you plan to install and test with Win 10, you can view the ID of the material missing material and someone might be able to find some for you (but no guarantee). Instructions > > http://www.wikihow.com/Find-Hardware-ID

  Personally, I would recommend that you take advantage of this computer with Windows 7. You have a wonderful notebook with excellent hardware configuration and nice operating system that will be supported by 2020. Something that usually works fixing it breaks

• How to install the Modem broadband 3 G on my Tecra R850

  I want to install hardware for high-speed mobile 3g in my Tecra R850 pt520a - 01 s 003. is this possible?

  This is a fairly new machine and I don t think that someone here can help you with this.
  I put t know if this model is ready for these updates.

  I recommend you contact the closest service Toshiba and ask for help. I'm pretty sure they're accurate and manual of maintenance equipment plans, where they can check if these updates is possible or not.

  By the way: where do you buy the material missing for upgrade?

• Satellite L300 - 12L is not picking up wireless connection

  I just did a factory restore on a Satellite L300 - 12L sound do not pick up any wireless network.
  Do we know if its material missing?

  Thank you
  Them

  Hello!

  What do you mean with it s not to pick up any wireless connection?
  Can you wireless networks?

  Why wouldn't be a missing material? If your laptop is equipped with a WiFi card (I'm almost sure that this is the case) and you don t have exclamation points yellow in Device Manager that s is not a hardware problem.

  Don t forget WIFI must be enabled with the hardware switch on the computer laptop and FN + F8.

  Good bye

• HP 450: Is that what this laptop contains chart AMD?

  Hello
  I recently bought a laptop which the model has been specified as a simple "450 HP".
  
  So my question is, my computer contains AMD graphics?
  I tried to install the AMD driver available on the HP site, but it has not been successful. (only intel HD4000 is displayed in Device Manager)
  
  its basic configuration is the following:
  
  3230 M I5
  HARD DRIVE 500 GB
  4 GB OF RAM
  
  It seems to be this one: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03315510
  
  But the processor does not match. one installed in the present is an i5, whereas the above specifications refer without exceeding i3.
  
  While the specs mention chart AMD, and drivers are available on the website of official drivers HP450, all my attempts to install the supplied driver (downloaded from HP) failed.
  (he never mentioned material missing. it says ' warnings occurred during installation. ") (please see newspaper"but does not have the button"view log")
  
  The intel driver installed fine.
  In the device, under 'graphics adapters' Manager, is shown only the hd4000 intel.
  
  Thanks in advance.
  -Lorenzo
  
  My system with export information can be found here:
  
  https://docs.Google.com/document/d/1Oh1TxpLn52x2R3ri4lv9gJuseTjdnrw49MhWxnx_0Cw
  ______________________________________________________________________________________

  Hello again,

  I found the following infromation.

  http://PartSurfer.HP.com/search.aspx?SearchText=E9L71PP

  If your laptop has an AMD graphics card included there should be written here.

  Unfortunately, your laptop does not use an AMD graphics card.

  If I'm right you have this processor:

  http://Ark.Intel.com/products/72164/Intel-Core-i5-3230M-processor-3M-cache-up-to-3_20-GHz-rPGA

  It is a chip Intel® HD Graphics 4000.

  There is another option to determine if you have a graphics chip AMD!

  You might find if available, the ID of the grahpics chip AMD hardware.

  (Use as reference only)

  http://www.WikiHow.com/find-hardware-ID

  That the "View card" menu offers you more as a non-unique hardware?

  Drunks.

• Satellite A105-S2051 does not supply power to the top

  I have a client who brought in their laptop, A105-s2051 that when you turned on the device, he would go on and then off. While you press the power button, it shut for about 2 seconds, then off, then on ect for 6 times and stay off.

  I first replace the RAM always loop, then took off material one by one and tested, always in the loop. I then had the MB from the case and plugged in power, always looping on and outside. Checked the power supply, which was right. Also, tried every start with material missing with/without battery on each piece.

  So I installed a new processor, always looping. Only thing left MB. Classes listed in MB, guess what, still a loop. Fixed several hundred laptops, did not run in this with a Toshiba before. (Another producer to do same thing once, turned the PS would lose slight tension after 5-6 seconds).

  Here, I'm stumped, any help would be great. Thank you.

  Which is really strange because you changed a lot of material.

  Then I'd go to an official ASP. You will find a:
  http://www.CSD.Toshiba.com-online repair => locate a repair center

• To write a waveform to two outputs analog of DAQ(USB-6215)

  Hello

  I use USB-6215, who has two analog outputs and having to send the same waveform through the analog outputs two of my DAQ. at the same time. in fact, I have a text file consisting of a code word (please see the attatchment) with dt, freq and annex 0 in the first column and other columns contain the word coded. Withe the help of dt, the rate and the data I did a waveform with the wave of construction VI. I am able to write this wavefrom through an analog output A01 right now. I want to know how I could write the same analog waveform other AO0 out simultaneously. I use a source of external triggering via PFI0 to be triggered. for now, I use the write.vi DAQmx (analog channel 1 DBL 1 d N samples) and DAQmx create virtual channel.vi with dev1/ao1 as the physical channel. For more information, I am attatching the program along with the text file. Please see page 2 of my structure of matter in the VI attatched.

  Thank you.

  Kind regards

  Raja

  Hi Steve,.

  his works now. I changed the instance of writing DAQmx for analog waveform samples N channel N. still, I now that a single waveform. How could I do like two like it (writing DAQmx) will not accept a single waveform as the entry as the number of channels in the task will now be 2 where, under the waveform has an exit.

  Kind regards

  Raja

• How to make knot faster formula?

  Hi all

  I am trying to identify a known model of the Spectra peaks in a code from Labview real-time data collection.  My data collection occurs on intervals of 50 ms (20 Hz).  Unfortunately, my analysis routines take ~ 160 ms to complete, and for this purpose the causes my material missing data collects.

  Using the profile tool, it seems that one of the principal offenders is a subroutine that predicted what should be the entire spectrum, assuming that a few common summits of the desired spectral design are in the spectrum.  It creates a spectrum of Gaussians for prediction, which he then compares to the heights of the real.  If it isn't well correlate, then the proposal is false; If it is proportional, the code returns then what are the masses of the peaks.  I can then find the limits of the peaks (I need the area of the Summit, not only the location of the tip) and use them to science.

  In any event, it must cover the subroutine to make frequencies predicted several times.  In general, I plan the locations of 4 peaks in the spectrum, and the spectrum is usually long 3000 points.  My routine to a predicted spectrum has the following entries:

  

  When the size is the number of points, width is the width of 1/2 of all summits, the amplitude is the height of an individual peak and Center is the location of the peak in the spectrum of 3000 point.  Table Gaussian is the output.

  The code looks like this:

  

  (vi attached below)

  My question is: can I can do something to improve the speed of calculation (in other words, I do something stupid?)?  Or is it just about as effective a subroutine as is possible?

  Thank you very much for your understanding!

  RipRock

  
  

• Re-install XP on a Fujitsu - Siemens Amilo Pro V2000 Laptop.

  Hi all out there. It's my first time here, I hope not my last. I hope someone can answer the question below, or can point me in the right place on the forums, find the information that I need to solve the problems, there is with the machine.

  It's NOT my laptop, I just look for someone else (never a good idea I know!), because I thought I knew a reasonable amount about computers. The person who is the owner of the laptop is on benefits and has very little money. The purchase date is not known.
  The hard drive has failed and so I installed a new laptop. However, I'm unable to re - install Windows XP! I formatted and initialized hard drive and partitioned into two. I resorted to downloading the XP boot from floppies (three times on two different computers!) direct from Microsoft. It downloads on 6 floppy disks (remember, so slow!). XP starts to load and takes the first 5 disks, ok. Drive 6 starts to load and then give the BSOD! every time! I tried every thing & scrap of knowledge I have (which I think was a fair bit after having used computers since 1986 & BACK) 3 I also wrote my thesis on computers at the University).
  All the others were there any other information or advice or anything like that, that will promote the position from here. Additionally, this morning the machine start at all, it now just to give four 4 beeps and stops, & will not do anything else.

  Hoping you can help, as soon as possible.

  Thanking you in advance & regards

  John Bates BSc (Hons).

  Hello Mawgwr

  The Microsoft Answers community is supported by users like you and Christophe. Nobody here is paid. Most of the information found here is provided by members and their time is voluntary. That said, Christopher was only you pointing to a community focused more specifically on your system.

  As for your question, Windows XP installation is not your biggest problem right now, the system not boot the system and give the beep codes is. It is an indication that perhaps the material missed somehow. I found some information on the beep codes for your system. However, the listed codes found 1 single seems to fit as you have described. 1 long beep and 3 short beeps. It is an indication of memory failure. My suggestion would be to try to start from only one card memory and consider the charging system, or you may contact Fujitsu to hardware support. Thank you.