Mavericks on external partition does not start

Similar Questions

• error 0xC0000225, recovery partition does not start

  Hello

  I have a HP dv7 with Windows 7 Home premium 64-bit.

  A few months ago, I did a factory restore, the recovery partition start (I have no recovery disks). After that, I thought to divide my C: partition where Windows is installed, and I did it with Windows disk management.

  So my new scores were: C: D: with recovery, OS, E: HP_Tools and g.: the new partition.

  A few days ago the sistem ran very hard, so I thought I do another factory restore from the recovery partition. When I rebooted and you press F11, I got the "0xc0000225 error".

  I have a Windows 7 Home Premium 64-bit bootable drive and I tried Startup Repair tool and other repairs of sistem, checks HDD, but everything seems to be ok.

  I reinstalled the operating system, from the disk bootable on C: (OS starts and works well) and let the other partitions as they were... but it seems that the recovery partition still does not start if I can do a restore from the factory with all the drivers and utilities, as they were at the beginning.

  Any ideas on how I can do?

  Thank you!

  It seemed that it there was not much I could do about this problem. My disk is dynamic, there is no Recovery Manager from the Start Menu, there has not been any creation of HP with HP folder recovery support. I managed somehow to make a repair disk, I tried it but no results, the error kept popping out every time.

  I inserted the Windows 7 disc to try to delete all partitions, including the recovery and HP-tools and do a Windows Installer Cleanup, but the Format, New and Delete buttons are inactive.

  I did some scans disk and memory tests, everything was ok... I started with a disc of Hiren and accesed the HARD drive with a program based on linux and so I managed to delete the partitions.

  After I installed a new copy of Windows 7 to work with my SN and everything was ok. Unfortunately I lost partitions recovery and HP-tools, but at least it works well again.

  Thanks for your all your support.

• Vista Boot Camp partition does not start

  I have been using Fusion to open my Boot Camp with Vista Ultimate installed partition.  It worked fine for months.  Suddenly, I get a windows Boot Manager error.  The message says that some required files missing.  Here's the weird: I can open the Visa using Boot Camp partition.

  Any ideas?

  Tim

  Note: These steps assume that you have a default Apple installation of Windows and a VMware Fusion Boot Camp Virtual Machine default partition and if you changed the Boot Camp partition the Virtual Machine to add additional hard disks to be virtual or RAW disk then do not use these instructions unless you backup the Boot Camp partition the Virtual Machine package first.

  1. If the merger is open, close it.

  2. in a Terminal (/ Applications/Utilities/Terminal) copy and paste command, as the following and then press Enter and it will remove the Boot Camp Virtual Machine meta-data partition. Note: This does not affect the Boot Camp partition to install Windows. Also make sure that you copy the entire command below "rm" line at the beginning of the ' (quote) after the p in the Camp. "

  RM - dfr "/Users/$ the specified item was not found./Library/Application Support/VMware Fusion/Virtual Machines / Boot Camp."

  3. start Fusion (/ Applications/VMware Fusion.app) and select the Boot Camp partition on the library of the Virtual Machine window, and then click the run button.

  Notes: Then, an authentication dialog box appears. "VMware Fusion requires that you type your password." Enter your name and password, and then click OK. (It is necessary to remove the Boot Camp for the merge partition to access it directly).

  Then, we should see a Boot Camp partition message stating "VMware Fusion prepares your Boot Camp partition to run as a virtual machine. This may take a few minutes. This occurs once. »

  When the virtual partition Boot Camp Machine starts for the first time after this VMware Tools may want or will install/update and restart the virtual partition Boot Camp Machine.

• Drive external HARD with bootcamp partition, does not start?

  Hi all

  If I'm running into a bit of a problem. I had an older macbook pro (mid - 09), kept just upgraded HARD drive I had before I sold it. On this HARD drive, it has a partition Mac OS 10.8, and a boot camp windows partition 7. Now that I have my new Macbook Pro (mid-12), with an impressive but small SSD, I tried to start the windows partition via external enclosure. Im running in some points once I selected the bootcamp on the HARD drive partition. It tries to open windows, but I get the error "Windows failed to Start. Kind of stuck here, seeing that I won't try to Exchange hard disks for obvious reasons. Y at - there a fix, or any way around it?

  Windows 7 can not boot from an external device. Visit the Microsoft Windows features.

• Recovery partition does not start!

  Hello dear forum participants!

  I have computer hp pavilion dv6 laptop, recently I reinstalled original OS (win7 home 64 bit that comes with the laptop) to win7 Home premium.

  Now I want to return to the default settings, and I'm unable to start on the HP Recovery partition.

  When I press F11 at startup it boots regular OS, but not the HP recovery software.

  How can I get my work as a recovery partition?

  Problem has been solved!

  It seems that recovery partition boot records have been corrupted by the installation of the non-native OS, but the directory structure and files were intact.

  Steps performed:

  -J' created the recovery USB using HP USB recovery Flash Disk Utility disk

  Link: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-77449-1&lc=en&dlc=en&cc=us&lang=en&os=4062&product=4057188

  -Fact flash drive bootable using EasyBCD utility

  Link: http://neosmart.net/dl.php?id=1

  just add a new entry to point the finger removable WIM image, see documentation for EasyBCD

  http://NeoSmart.NET/wiki/display/EBCD/EasyBCD+documentation+home

  It's quick and dirty solution, there will be more estetically without creating recovery USB drive, simply add the for the recovery partition boot record.

  Thank you all for attenction!

  IonCannon

• Does not start after the reload of the operating system

  OK, this is my story of boredom.  I have a Lenovo T61 Type 6463-5BU, S/N L3-xxxxx.  The hard drive died a few weeks ago, and since then, I have received a replacement drive under warranty, that is the exact same drive type.  We had a backup image of the old system under Norton Ghost and managed to get the image to the new disk once it has been installed.  To do this, we used a utility called OS
  'BartPC '.

  Since then, I did pretty much everything I can think of to get the system to boot, including playing with the BIOS settings, setting the drive to 'boot' and 'active' with the help of a number of public services, including the good old "diskpart" and many others.  The reader will just not start.  A few times I could read the disc using Bart in command prompt mode, but I never managed to boot from it.

  The laptop has a finger print reader, but I was told several times that this has nothing to do with the problem.  So... before I cut off the finger of a person and drag in the player... What am I doing wrong here?

  Note of the moderator; s/n, under the direction of protection own members

  AGoodSolutionideas can save I hope as your image.

  For later use, take a look at this document from Lenovo on the use of Ghost; Partition does not start after being restored with Norton Ghost - NetVista / ThinkCentre / ThinkPad...

  I know it says 'prior to 2004 systems', but it is still topical.

• Recovery partition is there but does not start Recovery

  Hello
  
  When you try to restore the image (F11 at startup), the laptop seems to be as he tries to start missing Windows installation (Windows Boot Manager error page).
  
  Partitions 'SYSTEM', 'HP_RECOVERY' and 'HP_TOOLS' have not been affected. Recovery files of ~ 15 GB are still there!
  
  The Windows (2nd primary) partition was deleted and then recreated as an NTFS partition. Since then, the recovery process does not start.

  How can I restore my intact HP_RECOVERY partition system without using recovery DVD? (I can't access right now.)
  
  The partition Windows has need of a specific disk label? What is the magic that breaks the recovery when an NTFS partition is all simply deleted and then re-created?
  
  Peter

  HP ProBook 6550 b (WD701EA #ABD)

  Solution: How to fix F11 penetrates is not in the Recovery Manager process

  You will need:

  -This fix by HP: difficulty to the Multi-partition HP Recovery Manager (the ProBook 6550 b is not listed as a supported model, but it worked for me)

  -installation of Windows (see partial solution above) a job to install the fix on your ProBook

  or

  -sufficient knowledge to extract the winre.wim missing the fix above, copy it to your recovery partition and to apply any measures necessary (I did this)

  Steps to follow:

  -in your work on your ProBook Windows installation open the file downloaded "sp48415.exe".

  -the files will be extracted in "C:\swsetup\SP48415", open this folder in Explorer

  -Right click on "F11SPFix.cmd" and run as administrator

  -the patch will be applied

  Restart und press F11 at startup to enter your recovery Manager (hopefully) fixed.

  Credits to HP support.

• SSD external via USB does not start by default

  Hello Apple community.

  I have a problem with my new external SSD. Given that the base model Mac Mini end of 2014 comes with a disk HARD 5400 RPM drive, I wanted to go to an SSD without having to tear the whole unit. I wanted to exhaust the option 'boot from USB' and I'm having a strange problem. I cloned my Mac to the new drive SSD and slapped in a box set of the speaker. I connected via USB and changed my 'startup disk' to use the external SSD drive. However, it does not start on this unit automatically. When I reboot and discovers the "boot manager" I see the USB being initialized automatically. After disconnection / re - plug the drive in, it appears as a boot option. Once it is initialized, everything works fine and I can boot into El Capitan without any problem using the SSD.

  I am trying to find a way that I can get the Mac to initialize the SSD to the boot upward and choose default. I don't want to have to re - connect the drive whenever I want to start on the SSD drive... Any help and suggestions are greatly appreciated!

  My equipment

  ===========================

  Model Base of Mac Mini (end of 2014)

  1.4 GHz Intel Core i5

  4 GB of DDR3 1600 Mhz

  OS X - El Capitan v 10.11.3

  240 GB SanDisk SSD more - connected via USB3.0

  What unit do you use for the SSD?

  Can you provide a link?

  If the SSD is delivered with a box to provide a link to that,

  How do clone you for the SSD? What app did you use?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable, reinstall the OSX. Nothing shall be lost

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• HP envy Phoenix: win 7 does not start with connected external hard drive

  I have a desktop HP Envy Phoenix with i7 chip and an SSD for the OS.  If I connect via USB external drive of 3 TB WD for the backup of the system does not start while it is attached.  The pc seems to be trying to boot from the outside, can't find the OS and does not start.  It will start fine with small external drives connected.  It is the size of the disk? Is there a way to fix this?

  Hello

  The WD drives seem to pose problems of my potential.  I have used other brands such as Seagate and Hitachi without running into problems with external USB drives causing the system to boot.  Maybe it's the USB adapter that I use which does not cause starting problems.

  @tpetras

  I used the adapter HP USB 3, which uses drivers NEC or TI and has never had a problem starting via a USB external (non - WD) readers.

• Win 7 does not start after the creation of new partition for fileswaping.

  Hello!

  As the header says, Windows 7 does not start. Made a partition to swap files between OS X and Windows 7.

  I saw in a thread that it could be repaired using fdisk. I'm really new to OS X, so I did not really

  know what to do. Writing the result of the controls, I found in the thread.

  I know now there is a warning to the partition AFTER installing Windows.

  Would really appreciate if everyone took some time telling me what to do!

  diskutil list

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage MacBook Hoveddisk 382,5 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database FILDELING 16.6 GB disk0s4

  5: Microsoft Windows HD 100.0 GB disk0s5 data base

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD GB + 382,2 disk1

  Logical volume on disk0s2

  AD4E7A3F-9F8E-4734-8B4B-B65587CDD2A1

  Unlocked encrypted

  Fdisk/dev/disk0

  Disk: geometry / dev/disk0: 60801/255/63 [976773168 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 1023 254 63 - 1023 254 63 [1-409639]

  2: AC 1023 254 63 - 1023 254 63 [409640-747116216]

  3: AB 1023 254 63 - 1023 254 63 Boot Darwin [747525856-1269536]

  4: 0 b 1023 254 63-1023 254 63 [748795392-32403968] Win95 FAT-32

  TPG - v - r see the/dev/disk0

  See the TPG: / dev/disk0: mediasize = 500107862016; SectorSize = 512; blocks = 976773168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  start index size summary

  0 1 MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 747116216 2 part TPG - 53746F72-6167-11AA-AA11-00306543ECAC

  747525856 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  748795392 32403968 4 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  781199360 262144

  781461504 195311616 5 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  976773120 15

  976773135 32 table dry GPT

  976773167 1 dry GPT header

  Please after the release of

  sudo dd if = / dev/rdisk0s5 account = 1 2 >/dev/null | hexdump - C

  You see the Windows files in the volume of training using the Finder?

• HP 250 g3: hp 250 g3 does not start with windows 8 ir says the GPT partition style

  HP 250 g3 does not start with windows 8, it is said GPT partition style and custom boot that I have fomarted the hard drive... Please help

  Thnx man always the same thing, but I deleted all partitions and then I was able to start...

• 7 does not start with a connected external Western Digital hardrives.

  I have two external hardrives WD, connected to a pc to the bridge under windows7.  When the hard drives are connected, Windows7 does not start.  It hangs on the black screen.  Without the disks attached, it starts very well.  Anyone know what I can do to not having to pick up leads outside whenever I want to start?

  Solved.

  Use Windows Update to install the update from Western Digital Technologies WD SES device released by Microsoft in January 2011.

  My system hangs is no longer with USB Legacy Support set to 'Auto '.

• Windows 7 Home Premium does not start and an external monitor connected via DVI to HDMI Cable

  I have a Dell Inspiron 531 desktop computer with a NVIDEA GeForce 8400 GS video card.  This video card has the following outputs: DVI, VGA and S-video.  When I connect it to my computer via the VGA port to PC to my Sony Bravia KDL-40XBR4 monitor port, the machine starts perfectly.  If I connect via a HDMI cable to one of the HDMI monitor DVI ports, the screen displays the video BIOS, but turns black when the operating system begins to load.  If I connect another monitor to the VGA port, yet once the machine boots fine, but if I connect the monitor to the computer and the Sony Bravia, once again the machine does not start.  The strange thing is that if I boot with only the connected computer screen and then plug the DVI to HDMI cable, then Windows 7 sees the Sony Bravia monitor very well, and I can extend the desktop.  If the machine mode 'sleep', both monitors work very well to wake up the PC.  So, if the Sony Bravia is connected alone or with the computer screen, the machine does not start (the screen will display 'go black' when the OS starts to load.)  I tried to run Windows in Mode safe, but he won't either.  I have all the updates of Windows applied and have installed the latest drivers from nVidea so.

  Hey Chris,

  First of all, about climbing, is not a technical support; This is a community forum where MS moderator and contributors are involved.  Now to your question ~

  It's very strange that the PC does not start when this unit is connected, but works fine when connected after the fact.  I've seen several cases where a hardware configuration of uinsusal will prevent a PC to boot.  I think that the culprit may be DVI to HDMI Cable that you are using.  If I were you, I try to connect the PC to a DVI monitor and see if it boots normally.  Also, see if the monitor can prevent another PC to start when it is connected directly via the HDMI.

  Good luck! Let us know how it turns out.

• NB200 does not start after the bios - screen black screen with blinking cursor

  Hello

  I was using the laptop as usual when I think there may have been a virus activity - reason I say that is that my anti-virus closed unexpectedly. I couldn't restart programs files.

  I restarted the laptop.

  After the bios menu will I get a blank screen with a blinking cursor - windows does not start.

  I did the following:
  (1) create a USB bootable with Recovery Console window XP - boot with this i can see three drives C:, D: as SDA? I can see the content of these disks, so it seems that my HD works. I ran a fixmbr and fixboot, but this has not solved the problem.
  (2) create a Kaspersky bootable USB virus scan - ran it without problem - he found a few question (not on the disk boot sector) I've fixed.

  An option was to copy files from the laptop and then start it in recovery mode - so Itried to run the phone into recovery mode hold down the 0 key at startup - the bottom of the screen then displays * HDD Recovery mode * and nothing happens.

  Any help - other options would be greatly appreciated.

  My 1 year of that guarantee has expired a few months back so can't send in for repair.

  Thank you

  Hello

  I doubt that it is a virus.
  Seems the file system is damaged on the HARD drive and this is the reason why the laptop does not start until it could also be a partition of HARD disk malfunction.

  Try this; Turn on the unit, press F8, and then check if you have the laptop repair.
  If this is not possible, then you will need to reinstall new OS.

  Here you can order a recovery disc:
  http://backupmedia.Toshiba.EU/landing.aspx
  Of course you will need an external USB CD/DVD drive

• Portege 3490, Windows does not start no-how to reinstall?

  Hello
  I bought a laptop portege flea market in US a few months ago. It was quite a good deal, but unfortunately it came without floppy and cd drives, only with the external network adapter.

  The problem is that now, Windows XP does not start upward due to some mess that I did with Acronis partition software-dos prompt just says:

  From Acronis Loader...

  The Acronis loader: no current configuration file.
  Press to restart...

  I guess that it is not really a problem if I had a floppy or cd drive. Although I would rather buy one just for unique operating system installation. (normally I use lan connection to transfer files between my computer).

  In any case, I would be very happy if you could tell me how boot/install OS using the LAN network connection (how to turn on my desktop pc into a CD drive on the server and dhcp on the network sharing, etc.). I tried to search the Internet to do this, but it is surprisingly bad comments on this topic, and toshiba so do not write on this subject in the manual...

  Best regards
  Aldous

  Hello

  Well, I think that somewhere, there should be information that it supports booting from LAN (PXE). But since this reqiures some heave stuff behind the LAN, it might be a little difficult to tell the whole story in the manual.

  Anyway, the way I am familiar with this is that you can start the machine from the LAN (or rather install the machine of the LAN) If you have an available RIS (Remote Installation Server). This isn't something that people generally have in their homes. What it takes is a Win2000 / XP or Win2003 server with active DHCP server. You will also need to prepare a special 'image' of the installation media (but there is a guide to help you with this in Win2000 server at least).
  After that, it should be fairly simple. Starting the machine of the LAN, get an IP address and by accepting to download the bootstrap of the server, login and then it really looks as if you dΘmarrez from a Windows Media.
  So in short - use it to Win2000/XP/2003 server and support for Windows of choice. Some LAN cables and possibly a switch/hub.

  If you can get your hands on a PC Card (16-bit)! CD Rom and can make a CD bootable, then that could be easier.

  Theoretical, you can also move your HARD drive to another PC and it is
  -install Windows on it

  or

  make 2 partitions and copy Windows Media to the second to the first bootable with f.ex. BACK/Win9X, bring it and install Windows on the first partition when the disc is in the 3490.

  But these 2 varaints gives 2 potential problms as they are complicated to solve:

  If you only install BACK/Win9X on the HARD drive you will get probably the problems to start the HARD drive when you put it in the 3490.

  If you install windows on the HARD disk, you may both get HARD drive boot problems and also get windows to load correctly due to differences in the chipsets.

  Sorry for a lot of words :)

  Good luck!

  Tom