Measure calories burned when using drive

Similar Questions

• Why doesn't a USB drive I have previously used with AirPort extreme appear in the finder when used locally with my Mac?

  Why doesn't a USB drive I have previously used with AirPort extreme appear in the finder when used locally with my Mac?

  I tried to plug it into my mac to transfer files locally but will not be displayed in the finder or disk utility. Anyone know why?

  MacBook Pro (2015 retina) OS X 10.11.2 El Capitan

  Have you shut down / turning your Mac off... power off the USB drive... Connect the drive to the Mac... start up the Mac... then, turn on the USB drive?

  If no help, there are a number of posts to the thread in the forum El Capitan of support from users who have problems on their Mac USB.  You can post there to see if anyone has the answers.

  OS X El Capitan

• Error message indicating the r300 display driver stopped responding when using the full screen.

  Original title: driver atikmdag error message when using the full screen.

  Error message indicating the display driver r300 unresponsive, but has recovered, usually when enter full screen mode.

  Hi Peterrichardson,

  1. when exactly you get this message?

  2. what player do you use?

  3. you remember to make changes to the computer before this problem?

  Method 1:

  You can try to reduce the hardware acceleration and check.

  a. click the Start button, Control Panel.

  b. now, select appearance and personalization, and under display, select adjust screen resolution.

  c. now, select adjust the resolution.

  d. click Advanced settings.

  e. now, click the Troubleshooting tab, and select the change settings button.

  f. in the Security dialog box, click on continue.

  g. move the hardware acceleration slider to the third notch.

  h. click OK and restart Windows.

   

  Method 2: Update your display driver

  Updated a hardware driver that is not working properly

  Hope this information is useful.

• Active calories burned after upgrade of the phone

  I have recently updated from an iPhone to an iPhone 5 6. I have not matched my Apple Watch from my old iPhone and paired with a new one. Everything seems to work fine except the assets calories on workout sessions. The number of calories burned is about half of what they were before I changed phones. Someone else had this problem?  Thank you.

  HI - try the following steps:

  • If you have not already done so, it can help to upgrade your iPhone and look at the latest version of the software:
    • Update the software on your iPhone, iPad or iPod touch - Apple Support iOS
    • Update the software on your iPhone, iPad or iPod touch - Apple Support iOS
  • Check that your personal information is accurate:
    • On your iPhone, in the application of the watch, go to: My Watch (tab) > health > check and, if necessary, change your date of birth, sex, height and weight.
  • Restart your iPhone and your watch. Close the two devices together, and then restart your iPhone first:
    • To turn off your watch: press and hold the button side until you see the cursor off the power; slide it to turn off;
    • To turn it on: press and hold the side button until you see the Apple logo.
  • While training, to optimize the performance of the heart rate sensor (data from which is used when estimating calories), make sure you wear your watch fits on top of your wrist. Apple suggests that consider you the clamping Strip before starting a workout and it loosen again thereafter.

  If the problem persists, it may also help to reset your calibration data and start over:

  -On your iPhone, in the application of Eve, go to: My Watch (tab) > privacy > Motion & Fitness > tap reset Calibration data.

  To calibrate again, follow the instructions in the article to support below, including:

  -Records training outdoor walk and/or run in the open air with the application of the workout on your watch.

  -It for 20 minutes at each speed to during which normally walk you or run.

  -While doing so, take your iPhone with you, with location-based Services market.

  -Allow your arms swinging naturally during the workouts (and also later, by walking or running workouts).

  More information:

  Calibrate your Apple Watch for better accuracy of training and activity - Apple Support

• Calories burned (under wellness\activity tracker)

  Guys, I realized that the W450 count my steps taken throughout the day, I wear the device, but I'm curious about something. When I discovered my activity tracker and it shows XXX amount of calories burned, is specific to the measures only? For example, yesterday I was at 8200 measures taken, with 4096 calories burned. I'm about 195 lbs. Also, I went for a stroll in cycling and weight lifting in the gym so I don't know it this graph is including both of my workouts, which totaled about 1600 calories. Thanks for the help!

  There is no way specifically look at this, but in the portal under training-> course past workouts, you can see all the activities that you did on a given day and slice by cals/distance/duration

  However, is not in the BMR and measures taken when not in a training mode.

• Error when using Google Chrome on Windows 7 x 64 BSOD.

  Hello

  I am experiencing BSOD random days on a pretty new install of Windows 7. It is not that occur when you perform heavy tasks (when making music with lots of ram and CPU in use), but (I assume) when browsing with Google Chrome. It seems completely random, can not find the problem... I have a .dmp file and downloaded to my dropbox. Maybe someone can analyze and find the faulty driver or something?
  Link: http://dl.dropbox.com/u/10938251/MEMORY.rar
  Hope to hear from someone!
  Thank you
  Pablo

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced

• Total number of calories burned per day?

  (Or may) the Apple Watch record total calories burned per day, including not only periods of activity but calories approximately during rest periods? Or is it just them count during training? I am currently using my Apple Watch with a heart rate sensor Polar Bluetooth H7 and would get an estimated number of total calories burned each day compared to my food intake. Y at - it another app, I would need? If so, what would be the most simple for this specific purpose?

  Don't count during training.

  "and I would get an estimated number of total calories burned each day compared to my food intake."

  No Apple Watch app that can do it.

• How to view the monthly/annual statistics in terms of time past/calories burned, broken down by each individual activity such as run elliptical/outside etc. Y at - it a third party application that can help me to collect and display these data?

  How to view the monthly/annual statistics in terms of time past/calories burned, broken down by each individual activity such as run elliptical/outside etc. Y at - it a third party application that can help me to collect and display these data?

  Hello

  It is not currently possible to review the data the application integrated in activity or training on this basis. If you want Apple to consider adding this feature, you can suggest here:

  https://www.Apple.com/feedback/watch.html

  However, health and fitness data from other sources, iPhone, and Apple Watch are registered and grouped within the health on iPhone app. These data can be exported, which you may find useful to track the cumulative progress and/or analyze your activity more in detail.

  IPhone app activity also has a button for sharing (top right of the screen) that allows to share data - including social media, Messages, Mail, Notes, and a printer.

  Include third-party applications that can be useful, for example:

  Access to QS

  -"Access your HealthKit data in a table so you can Explorer using numbers, Excel, R, or any other tool compatible CSV."

  - https://itunes.apple.com/gb/app/qs-access/id920297614?mt=8

  SpectaRun workouts

  -"View from the workouts of your Apple Watch on your iPhone and to export these workouts so you can download them to your favorite online running community."

  - https://itunes.apple.com/gb/app/spectarun-workouts/id991723862?mt=8

  Data can also be exported directly from the application of the health (Health Data > All - Share at the top button on the right).

  Check the descriptions and support resources for third party applications for supported details of import and data analysis features.

  More information:

  Use the activity on your Apple Watch - Apple Support

  Use of the workout on your Apple Watch - Apple Support

  http://www.Apple.com/watch/health-and-fitness/

• Y570 - sound disappears when using some applications

  Hello everyone, I don't understand what the problem with this laptop

  When using Skype, as soon as we establish contact video, sound disappears and Skype says there is a problem with my sound card

  I installed the drivers from the Web site, but that did not help me

  Please give me a hand on this one, because I tried to contact my father for a week now...

  Download Yahoo Messenger now, PM me your account so that I can contact you!

  UPDATE:

  No need to contact, as soon as I tried to do a test call via Yahoo and when I got to the menu where you choose your micro/sound card, the sound disappeared again (it disappears completely, which means that everything is muted, Foobar even crashes with an error)

  UPDATE:

  Driver Realtek Web site, will try and answer as soon as I get no result!

  LAST UPDATED:

  Problem solved

  For those who have experienced the same problems, here is the solution:

  Go to the Download Page for Realtek

  Choose High Definition Audio Codecs and accept the contract

  Download this: Vista, Windows7 (32/64 bit) driver only (executable) (size = 99093 k)

  Delete all the audio drivers that you have right now, restart your PC and install new drivers

  Skype works perfectly and my father finally had the chance to hear me!

  Hope it helps you too

  See you soon

  Eugene

• Vertical lines shows that when using document feeder / have given help and discussions, no luck

  I have two printer hp models 1536.   Two of them have a vertical line when using the loader to scan or copy documents.

  When you place the point on the glass, scanning or copying is clear.

  Reading the discussions... tried to plug directly into the wall, cleaned feeder and glass, etc.

  I still have this problem

  Any ideas?

  Driver or firmware problem?

  The question is probably not a driver or firmware issue - it is probably a task on the thin glass used for playback through the ADF.  Try to clean the glass broadband of 1 "to the left of the main scanner glass. A tiny spec can cause the problem you are experiencing.  It can help to hold a flashlight almost parallel to the scanner glass to highlight all the stains on the glass.

• Different when using different reading software

  I use NI9205 and NI DAQ 9171USB, a battery and a DC output have been wired to NI9205.

  However, when using MAX (the creat task function), express Signal or a program, I created using DAQmx functions to get the output voltage,

  I got different readings for the same channel (20-50% of variation). and it turned out that only the readings of my own program are the same as what I measured with a portable meter,.

  Really do not understand how this could be possible? What's wrong with the MAX and the Signal Express?

  BTW, I made sure I put the connection method to be CSR in all three cases.

  Entrance to anyone who will be greatly appreciated.

  Problem solved. Everything is fine with the DAQ platforms

• My slider controls when using Excel and Publisher became too sensitive

  My slider controls when using Excel and Publisher have become too sensitive and more often, don't do what it is that I'm willing to do.  For example: while in Publisher if I click on a photo, that I've inserted, and try to move it, it will automatically open the Format Picture option.  She does it with a number of other features as well.  If I'm in Excel and I'm trying to highlight a phrase, it will begin to highlight the requested sentence, then the middle of it will stop after the sense that I'm going with my cursor and it will pass at the end of the sentence.  I guess you could say this kind of "jump" and the mouse became too sensitive with the controls.  It's really frustrating and it feels like it has a mind of its own.  At first, I thought maybe a low battery mouse, because she was the way she does when the battery is dying.  Changed the battery and no change.  I also tried to set my mouse speed and still nothing.

  Any ideas?

  Oh and btw this just started to happen during the first 4 to 6 months.

  Hi H.Morton,

  1. the problem occurs with excel and publisher?
  2. what operating system do you use?
  3. did you uninstall and reinstall the mouse drivers?
  4. have you tried with another mouse and check?
  5. do the mouse has a selection of sensitivity on the mouse itself?

  I suggest you to update the mouse drivers and see if that helps.
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• Receive the 25 (Null) error when using Flightsimulator FSX

  Receive the 25 (Null) error when using Flightsimulator FSX

  Hello

  Try to open the it to start - all programs - Games - Games Explorer, and then clicking the icon FSX.

  A disk error of 25 means that the program cannot read your disk reading.  Either the disc is scratch, dirty or defective.  If you need another drive, or you can try it on another computer. The message of Visual elements of Vista is not serious.  Vista will automatically your screen to a basic compatible mode when the application is launched.  However, it seems that your game is a failure due to the disk error and not the Vista display problem. Try to clean the disc and see if that helps.

  Last resort, it seems you'd have to do a complete uninstall and reinstall FSX.

  Cheers!

• Static in speakers when using Skype

  I have a PC laptop HP Envy Touchsmart IS-j052nr, running Windows 8.1.  When I use Skype, either through headphones or the speakers, I have problems from parasites.  It sounds clear when I speak and when the person at the other end is speaking, but if the person on the other end does not speak for several minutes, then the static method noise becomes stronger and stronger (like a huge storm of rain falling at the hearing) until the other person makes a new sound.  The other person can also hear static.

  Is there a new driver, I can download to fix this problem?  When I scanned my computer on the support site there is no audio driver I was missing.

  Thank you!

  Hello SCLC.

  Welcome to the Forums of HP Support! I understand when you use Skype on your HP Envy Touchsmart j052nr IS running Windows 8.1 you hear static, whether you use headphones or speakers. Now you don't hear static noises when using Skype, or when using headphones or require sound from speakers?

  After some research on the Skype Support Forums, I've seen a few recommendations that I would like you to try to see if that reduces / removes this annoying static noise. Please follow the steps listed below:

  1 sign in to Skype

  2. go in Tooks > Options > General > Audio settings

  3 uncheck automatically adjust to the title of chapters of Microphone and speakers

  4. adjust the volume to your liking

  5 save and restart Skype

  If you are still having static noise, I wish that you continue here: Skype Audio issues troubleshooting

  Please reply back with the information requested, if the static noises are still there and it is only when you are using Skype, I recommend to go to the Page of Support of Skype as they would be able to help you.

  I'll watch for your reply.

  Source: www.skype.com/en

  Thank you

• Disk activity constant when using vista home

  Original title: I am running Vista Home premium and am sick of the constant disk activity slowing things down. I canceled the programs start and automatic indexing, but again the thing vibrates far. Does anyone have constructive ideas?

  Constant disk activity when using vista home. Any ideas how to stop it?

  Hello

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.