Memory of co-location: always running near max.

Similar Questions

• Pavilion 7000: Computer freeze once the fan CPU runs at max speed

  Product name: Pavilion 7000

  Product model: 7 p - 1090d

  Product no.: QP177AA #UUF

  Operating system: Windows 7 Home Premium 64 - bit version.

  Computer blocks once the fan CPU runs at max speed. Initially, the computer would occationally freeze after waking up from sleep mode (CPU fan would be occaionally operate at full speed & freeze the system).  Now cannot load even in windows. It freezes at the configuration of the BIOS once the fan turns at speed computer crashes if the CPU fan run at maximum speed wherever you are!

  1. I did the cleanning & lubrication & even take the battery to reset the Bios but no success too.

  (Before I can reset the Bios it will run normally.)

  2. remove all USB devices except the mouse & keyboard

  3. detach & attach Ram memory & graphic card

  I saw a ROM_Recovery shunt on the motherboard label. Must I do? or can someone help, please?

  I sent to the center of HP service after a week, the service staff telling me that he was unable to go bad because my motherboard is the American version, which I have no idea what it means (my PC was purchased locally) but to bring him back.

  I solved my problem of tried to detach the Rams (2 actuators) & install only 1 on an another RAM slot first. This works. Then installed the second RAM on an another slot also without no problems so far.

  I have an old HP Office also having the location of the faulty RAM & also had replaced graphics card but it raise a peep sound error which easier to identify.

  I agree with you more HP, hardware problem is due to RAM or video card. Thanks anyway

• What is the amount of memory (live ram) required to run windows 10

  What is recommended the amount of memory (live ram) required to run windows 10

  System requirements:

  * 1 gigahertz (GHz) or faster 32-bit (x 86) or 64-bit (x 64) processor

  1 gigabyte (GB) of RAM (32-bit) or 2 GB RAM (64-bit)

  * 16 GB of disk space available (32-bit) or 20 GB (64-bit)

  * Peripheral figure DirectX 9 with WDDM 1.0 or higher driver

  https://www.Microsoft.com/en-us/Windows/Windows-10-specifications#sysreqs

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10
  • How to: determine if a device application or hardware is compatible with Windows 10
  • Will remain the documents and applications, or install app must

• Satellite C850-B076 fan always running and won't stop

  My Satellite C850-B076
  the fan is always running stop and today I received the alert on the cooling system system message will not have problem, and I should shut down the system and turn the unit back in service!

  Any notice, what's the problem? and how to fix it?

  Kind regards
  Tati

  On this virtual path that it is not possible to provide accurate diagnosis, and to say with certainty what the problem is here, but if the warranty is valid contact Toshiba service as close as soon as possible and ask for help.

  They have to fix.
  Unfortunately, this kind of problems, your possibilities are quite limited.

• Satellite Pro L series: fan always running even at IDLE when LAN is on

  the fan always running even at IDLE when lan is on
  Thanks for any help, that can stop the fan...

  Just see your questions:
  What model of laptop do you have exactly?
  What system do you use?
  What exactly do you mean by power of LAN?

  I can tell you that the cooling modules are controlled by fan table stored in the BIOS.
  Usually, the fan starts to spin if the CPU would be responsible for some unique applications/processes. It would also be possible that your fan is running continuously with low performance to maintain the low temperature. This isn't a real problem for laptop.

• Portege Z830 - fan noisy and almost always running

  My new Portege Z830 has the issue of noisy fan and almost always running which has been said here before.

  Recommendations were that we download bios 1.6. But I checked and that the version is already installed on my machine. I also adjusted the power save mode battery parameters as others have suggested. But that made no difference,

  All the other tips has been give in technical language far this beginner.

  If anyone has any suggestions they might put in words of one syllable and the step by step instructions, I would be eternally grateful. Thank you.

  I found also two documents from Toshiba on exactly this topic and as saying that update BIOS version 1.60 or higher would solve the problem

  Portege / Satellite Z830 high cooling fan speed.
  http://APS2.toshiba-tro.de/KB0/TSB23039P0000R01.htm

  and

  How can I improve the control of the FAN on the Satellite and Portégé Z830?
  http://APS2.toshiba-tro.de/KB0/FAQ22039H0002R01.htm

• Satellite A300 - fan always runs at full speed after full stop

  When I stop the Satellite A300, the fan always runs at full speed.

  Hello

  What? Cooling modules run, even in this case, the cell phone is off?
  Press the power button for at least 4 seconds, then the laptop must be turned off.
  Disconnect the power adapter and remove the battery
  Wait about an hour and reconnect the battery and AC adapter
  Then switch on the device after a certain time of use of turning the unit off and check if the cooling modules would stop too

• Re: Satellite L550D-12F - fan is always running

  Hello!

  We have a Toshiba L550D-12F and we are quite satisfied with the device itself - if it wasn't noisy fan. The fan ALWAYS runs audibly and I can't find any setting in the BIOS to its control.

  For my pain verxy I do not also find a support contact form to contact Toshiba so I hope that someone here will have a solution... Thank you very much!

  Sincerely,
  Matthias

  Hello guys

  I hope that my advice will help a little. I recommend you to use the laptop with the balanced power plan. Pleae change also advanced for this plan. In the advanced settings, you will find Toshiba power saver and the cooling method options. Place the change on the lower level.
  It should reduce the activity of fan.

  For example, when I use my Tecra A11 at the office for Office and mail applications I use for laptop and power management standby runs very quiet but the performance are always good.

• Satellite P100-347: after update 4.10 BIOS fan always runs at maximum

  Hello!
  I have a P100-347 and had graphics problems of stuttering while playing games. Updated BIOS 4.0 to 4.10, it solves the problem of stuttering!

  Now, my fan always runs at maximum, it never ideals.
  It's always the same, even when I choose its configuration. I use the same drivers as before, just only update the bios.

  I tested with the latest divers chipset intel and Nvidia alsow driver and it's always the same.
  So my concludes is the BIOS, is Toshiba knows something about this problem and work on a newer bios?

  Sincere friendships Ishmael

  Everything indicates that the BIOS 4.10 is the problem common to the always high speed of the graphic fan even when the PC is in sleep mode.

  I want to see action as a new revision of the BIOS 4.10!

  / Ishmael

• Rear chassis fan Z400 always runs at high SPEED

  I have several Z400 workstations. One of them is much noisier than the rest: the rear system (case fan) fan is almost always running at high RPM. On the normal Z400s, the BIOS Setup. File | Speed of about 1 600 rpm of fan reports of temperatures of the system chassis. On the noisy Z400, the chassis fan speed is reported as 3752 RPM. The two Z400s run the latest version of the BIOS public, 3.57. Both have a BIOS Setup | Power | Thermal | Fan Idle Mode set to 1. Fan Idle Mode 1 to 5 on the normal Z400 cycling makes a huge difference in fan RPM. Bike 1-5 on the noisy system has hardly made a difference.

  How can I calm the chassis fan in the noisy Z400? I carefully cleaned to vacuum inside the Z400, including the withdrawal of the air cover that protects the DIMMs. If it's important, the Z400s running Windows 7 Pro with all the latest patches.

  I noticed that the BIOS Setup. File | Temperatures of the system reported a temperature of 23 C on the 0C on the noisy Z400 Z400 normal. Are there opportunities that "0C Température" means that the room temperature sensor is broken, and without knowing what the temperature, the BIOS runs the fan at full speed no matter what? If so, how would I debug/fix this?

  Thank you.

  Scott, you are quite right.

  I replaced the on/off switch and LED cable assembly, including the thermal sensor, on the noisy Z400 with a plug to a normal Z400. The noisy Z400 is now normal, with a rear chassis at about 1700 RPM fan. The BIOS reports the temperature of ambient air properly to 23 C.  'How to' instructions from HP for the replacement of the cable were good enough. Now all I have to do is to order another set of good cable.

  Scott, thank you very much, for the rapid diagnosis and useful links. This issue is RESOLVED. Thanks again.

• Unable to locate labview run time engine

  Hi all

  I have a problem while trying to run a simple labview software on a Tablet PC.

  My development machine is under win 7 64 bit with labview 2010 sp1 10.0.1

  My computer is a win 7 32 bit based tablet.

  I installed labview runtime engine TEN 2011 standard 32-bit sp1 but I get the following text: «unable to locate labview run-time engine...» "

  I tried to install sp1 64-bit of the 2011 standard RTE because one of the items suggested, but windows is not allowing to install 64-bit applications...

  Should which version of the Runtime I install!

  You did not say, but I'm assuming that you are using LabVIEW 2010 sp1 32 bit to develop and build the application.

  You can include the 2010 sp1 Runtime when you build the Setup program, or you can download it (here) and install it separately.

  (The runtime version must match the development system, so time to run from 2011 will not work. Even the 2010 (non - SP1) could cause problems)

  Kobi Kalif wrote:

  I tried to install sp1 64-bit of the 2011 standard RTE because one of the items suggested, but windows is not allowing to install 64-bit applications...

  Can you tell me what position suggested to install an operating time of the wrong version of 64-bit. That makes no sense at all! Please provide a link.

  (You can only install the runtime on a 64 bit OS, 64-bit, and he will agree only if the application has been developed in 64-bit LabVIEW to the same version.)

• Windows Update always running in background

  Hi all

  I am running Vista and have reformatted and reinstalled three times in the last four or five months.  Whenever I installed, the pc works fine for a while then after a windows update, I don't know which, I start getting a lot of substantive activity on my hard drive.  This activity relates the mouse so much that sometimes it won't let me move it for 10 to 20 seconds.  Even with the keyboard.

  After each reinstallation, I load Vipre, to update and run a security analysis. Can I update Vista with each patch MS listed as critical or recommended before installing other software.  Now, all that is loaded is MS Office, Adobe Web Premium, Sony Ebook Library and some printer drivers.

  Manager tasks indicates little activity, 1-3% on each of the 4 hearts.  I restarted in safe mode, just to see if it might be something that takes over and I have the same problem in safe mode.  Lock the mouse and the hard disk activity.  Again, all the security scans show nothing other than a few cookies.

  I saw in other Councils there have been problems with either Windows Update has blocked upwards or with the MS .net framework installed.

  Someone has seen this before and if yes is there a solution that doesn't require a reformat and reinstall?

  Thanks in advance,
  Eric

  I'm still confused why you say "Windows Update is always running in the background" If you have not confirmed it.

  -Online open tasks on the process tab Manager: is there always an instance of WUAUCLT. EXE running in the background?

  Moving...

  After a clean install, you will have the equivalent of a "new computer". After each cleaning installed, you take care of everything on the next page before connecting the machine to the internet or a network otherwise and before using a USB or SD card that was not brand new, or had not been freshly formatted?

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Is WinXP fully patched to Windows Update & is also installed & updated VIPRE up-to-date?

  The foregoing notwithstanding:

  On the Vista partition:

  1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. click right on the file saved in #1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  On the partition of Windows XP:

  4. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  5. close all open applications (that is, anything with an icon on the taskbar).

  6. double-click on the file that you saved in #4 above to run the utility. DO TAP not your keyboard until the race ends, then restart.

  Not better?

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Is it possible to autostart apps or set them to always run?

  My son is in the army stationed abroad. We skyped on my laptop but I really my Xoom with me much more often. Is it possible to install Skype to always run so that he can find me whenever he is?

  Skype cannot make video calls at the moment on the Xoom, I hope soon, but yes you can do show you online always as long your Xoom is turned on it is. Open your Skype and press the settings button in the lower left corner of your screen he loves as a group of six small boxes. Then select settings from the context menu. In the settings menu, select "disconnect", then from the menu select never. Goolge about how ever chaton of will and can be downloaded on a computer for use through a google account, a bit like Skype.

• If the start of processor to consume more energy (I mean 80% or 90%) is also the pleasure of the processor starts automatically on more speed or it always run on the same speedd

  Hello

  If the processor starts to get warmer or runs faster (I mean if he starts using 80 or 90% of its power) the processor fan also starts automatically run faster or the pleasure of the CPU always runs on the same speed.

  Thank you

  Johan

  Hi Johan,.

  It is correct.  The fan works more quickly to cool a processor that is widely used.

• My dekstop cc wheel application is always running and stay white white

  I download cc test for the 2nd time and my dekstop app wheel cc is always running and stay white white

  I have try all the solution which had given before in the forums, for example delete opm, oobe, rename, disable firewall, reboot n all m using windows ultimate n nothing is a job for me, almost 5 days, I stuck in this please someone help me get the frm this mess

  Please see this link for more information:

  Blank white screen

  and these forum links:

  New Creative Cloud application unusable: it is empty! (WIN) or
  Re: opening of Creative white cloud app (MAC)

  Guinot