Memory test failed w / Kingston 4 GB
I have a HP G42 - 461LA Notebook PC, and I added a 4 GB Kingston Ram memory (KVR1333D3S9 / 4g). I started to notice my laptop has been slow and has decided to conduct a Test of memory of the HP Diagnostic tools (F2).
It fails with this failure ID: U3439W-5HW70M-XD002K-40HU03
When I removed the memory stick and tried again he passed successfully.
The strange thing is that when it is installed it is recognized and it seems like it should work, but it is slow at the opening in a few tabs in the browser (most audio glitches), and the test fails.
Hello
ID failure indicates that there is a problem with a memory, and must be replaced. This should be the cause of the issue of the slow-running also.
I suppose that there are two locations of memory for your computer.
You can try a memory at once and run the test or check the performance of the computer with a memory. Then, you will be able to isolate the faulty memory.
Sometimes it might be also the memory slot... so try a memory at a time in each slot in interchanging the. That will help you know if there is a problem with one of the slot.
You can refer to this link...
I hope this helps...
Tags: Notebooks
Similar Questions
-
Pavilion Memory Test failed., ID 64W662-5066J2-XD7XGK-400V03 failure
Crash... The BIOS memory test passes, but the HP Diagnostic memory test fails with the ID 64W662-5066J2-XD7XGK-400V03 failure. Product ID VM298UA #ABA. Any ideas?
Hello
Try the following.
First, download the Memtest Image file (.) (ISO) on the following link.
http://www.memtest.org/download/4.20/Memtest86+-4.20.ISO.zip
It is a zipped file, if you do not have an extraction utility installed, download and install 7-Zip. Please note that If you have a 64-bit installation, download and install the Installer x 64 64-bit .msi on the link below.
Then, right-click on the zipped file, select Extract 7 - Zip, select the files and then click Ok. Open the newly extracted folder to find the Memtest Image.
Now, you will need to use an application like ImgBurn to burn the ISO correctly on a blank CD - a guide on the use of ImgBurn to write that an ISO on a disc is here.
When you created the CD, shut down the laptop. Tap the escape key when you rewind to enter the Boot Menu. Insert the Memtest CD. Select 'Options of Boot' (usually f9), use the arrow keys to select the CD/DVD drive and press ENTER to boot from the disc.
At least 3-4 passes and see if errors are found.
Kind regards
DP - K
-
Test at startup "memory Test: FAILED.
Hello
HP ENVY Notebook PC m6
64-bit Windows 8
8 GB of RAM (2 x 4 GB)
I got a lot of blue screen errors so I made a diagnosis of start-up perform F2 at startup of the system and that's what I found:
Test at startup
Processor Check: PAST
Memory test: FAILED
Starting test: FAILED
Failure ID: U08K9R-6AE6S3-XD7X1F - 407 X 03
Product: C2C18EA #ABU
Memory moduleAny suggestions?
Thanks in advance.
Hello Rahat,
Start diagnostics is buit to check if there is hardware with computer problems. He has failed the test of memory which means that one of the memory on the computer module has failed and must be replaced.
If the computer is under warranty, I suggest you come in contact with HP Service Center and solve this problem.
Concerning
MathewT
-
Pavillion G6-1240sa: G6-1240sa Pavillion: BSOD repetition and memory test failed
Hello
I get errors blue screen on my G6-1240sa laptop running Windows 7 (64-bit).
SYSTEM_SERVICE_EXCEPTION
Technical information:
STOP: 0X0000003B (0XFFFFF80002F2D15F, 0XFFFFF880078CCB50, 0X00000000C0000005, 0 X 0000000000000000)
I made Diagnostics, accessed through the F2 key on startup and make me
Memory test: failed
Failure ID: 9BU2JX-5TA7MQ-MFPV4K-405503
Product ID: A3S574EA #ABU
Memory module
I removed the laptop 2 GB module, a 4 GB module is also present. After re - run the test, I got:
Memory test: failed
Failure ID: 9BU2JX-5TA7MR-MFPV4K - 405M 03
Can someone help me with this?
Thank you
Hello
Remove a RAM and run a test at the same time, if the test fails on both the RAM. You will need to replace both. If this is not the case, replace the one that fails the tests of RAM.
-
HP Pavilion g4-2149se memory test failed
Help! Memory test: failed
Failure ID:-GGC4R1-663702-MFPX1G-402203 do - what I do? This is perhaps why my system shuts down when I try to enter a program... IDKWarranty has expired but thanks... now I know what to seek and get help from fixation.
-
G6 Pavilion: Pavilion G6 Memory Test failed
Memory test failure 90fd7h-5nr82m-mfgh5f-402803
Product ID: LW350ua #aba
Any ideas on how to fix?
Thank you!
Hello
Replace the memory module.
Contact HP with the failure code. They will do it for free if you are under warranty.
If not, get a 4 GB key with exactly the same configuration, speed, etc. as shown in the manual. Crucial, Kingston are good brands that have their own online scanner, which contains the list guaranteed compatible sticks.
Manual: http://h10032.www1.hp.com/ctg/Manual/c02829479
Concerning
Visruth -
Hello
I use a laptop HP 1000. The default ram was 2GB but I added another 4 GB module in it. My laptop works quite normal, but it gives me the blue screen of death by practicing a particular game (League of Legends). I have no other than error, and it works fine. I decided to test my memory to the HP support (by pressing F2). I got the error of test with some ID of product failure.
So I ran Memtest86, there was no error proves Memtest86 in 1 pass. So I want to know that why HP test failed and Memtest86 gave me no errors.
OPERATING SYSTEM: WINDOWS 7 64-BIT
Thank you
Ahmad Salmat
Concerning
Ahmad SalmatI would say that confirms that the RAM module is defective. This test is performed on the single 4 GB stick or the also installed 2GB stick? If it was with the one 4 GB stick, then I would say that it is more than enough evidence to justify the Exchange store. There is not much I can do from this end with a third of RAM. You will need to contact the point of original purchase for an Exchange and explain tests memory failed (Memtest86 and HP).
Let me know what happens.
-
memory test failed for windows
Then?
The sticks of memory have failed or you have another hardware problem with your motherboard
-
Memory test failure...
HP Pavilion g6-1306ea on Win7
I run the development of System Test and on the memory Test failed with the following text:
Failure ID: 0LMPPR-66Q75F-MFPX0J-60R503
Product ID: B1W42EA #ABU
Can someone help me take this news?
Hello
Error code 24 characters for short drive Self Test (DST) would indicate that hard is defective and must be replaced.
If your laptop is still under warranty, contact HP (with the error code) and make arrangements for the disk replaced - you can check the status of your warranty here.
If you live in the United States, contact HP here.
If you are in another part of the world, begin here.
If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.
Kind regards
DP - K
-
Hard drive test failed, not found boot device
I have a Pavilion dv7 1245dx with Windows Vista 64 bit bought 2009 at Best Buy. He slid the arm of the couch on a carpet in stop down. Next day started ok, entered into yahoo, facebook, then type of frozen. Finally, don't do anything, turn off manually down, started upward. Black screen, "No. Bootable Device - Insert Boot disk and press any key". It will accept only the recovery disks that I made after the purchase. Starting test ok, ok, hard drive memory test failed 'Boot Drive not found'. If it helps, caps lock is flashing. I saw something in a forum on the reset or reinstall the hard drive but no explanantion how. Can you help me? And can you give me a ballpark figure on a new hard drive or better to buy a new laptop? Laid off in Michigan, hoping to be able to get the unit up and running without having to consider. Thank you very much for your help!
Hello:
Here is the link to the service manual for your laptop.
Can be found in Chapter 4, procedures for removal and replacement of hard disk.
http://h10032.www1.HP.com/CTG/manual/c01918142.PDF
If removing and reinstalling the drive does not resolve the problem, then the hard drive is dead.
I don't know what that means though the flashing light of caps. This could be something more serious.
A new hard drive will cost about $57.00.
I hope the recovery discs, you did work on it as well. They should but no guarantee.
http://www.Newegg.com/product/product.aspx?item=N82E16822148532
-
Starting test FAILED - HP ENVY 1191-NR
Hey guys/girls,
New to the forum - need some tech support. I have a HP ENVY3D 1191-NR running Windows 7. He recently began closing before you start completely. I ran a Test at startup and for the following results:
Memory test: FAILED
FAILURE ID: QE40XL-5GE6G4-XD0141-400103
PRODUCT ID: YL748UA #ABA
Memory module
Starting test: FAILED
I wonder if that means the RAM of the computer has gone wrong and I need to replace, or else... ?
Thanks in advance to all.
Hello:
Yes, that could indicate a possible memory module failure.
What I would do is unplug the PC and remove the battery.
If the laptop has two memory modules, remove one of them and plug the power adapter.
See if the PC starts and works normally.
If so, unplug the adapter, remove the other memory module, put in the first one you took, connect the a/c adapter and see what's the result.
If the PC does not start, you have isolated the bad chip and you can just buy a new one with the same characteristics.
If the PC is still under warranty, contact HP for a replacement.
-
Error code 2000-0123 Msg: memory - integrity Test failed
I have a DELL XPS9100
[Admin note: personal information]
[Admin note: personal information]
Maintain the label [Admin NOTE: maintain the label removed in accordance with the TOU strategy]
I also ran SEVERAL other tests - including Windows 7 memory test - it past
Test of Stress System (manual)
everything happened, but...
Advanced Pattern testing Test started 17/06/2016-21:15:17 Error message: The written model (5555555555555555) did not match the model read (5555555755555555) the physical address (000000025F55B088). In contrast to the model: 0000000200000000. 17/06/2016-21:15:51 Completion test: Failed (error code: WME22-0V0) 17/06/2016-21:16:05 file:///C:/users/CC/desktop/test%20Event%20Logs%20-%20system%20Stress%20Test.html
teenscrapbookHow to isolate tests of simple modules; knowing which module I test so that I know if I need to replace it
teenscrapbook
If you have two or more modules of memory installed, remove, reinstall one module, and then restart the computer and run the test, test messages no error, reinstall an additional module and repeat the test execution, if the test messages no error, repeat this procedure on all other modules.
Studio XPS 9100 service manual is HERE:
Bev.
-
Hello
Just a quick note before we begin, I'm not that tech computer of mind, so please bear with me.
Its a Hp Pavilion g series, running windows 7 (think 64 - bit).
Have portable receoverd after he high reading / suspension / does not not (or all of the above), but now it always crashes running the HP start-up test. He says that he didn't and he gave me the following.
memory test - passed
intelligent control - spent
DST short - failed
failure - OU7D7K-5QW744-MFPV4K-60QU03 ID
product ID - A7D65EA #ABU
tough - 1 disc
I know that something is wrong, but can someone please help and tell me what's wrong?
Thanks in advance
Rob
The hard drive failed the test and must be replaced. If you are still in warranty HP will send a replacement. If this is not the case, a laptop SATA hard detail can be used. Just be sure to get a quality at least equal the original in order to use recovery disks. It may be big, but not small ability more. For example if you have a 500 GB hard drive you can use a 750 GB hard drive, but not a 320 GB hard drive.
If you need help for selection/replacement of the hdd post back with the complete model & product number as indicated on the Service tag on the bottom of the laptop.
-
the start-up dv7-7259nr test failed
My dv7-7259nr startup test failed.
Here are the results of the tests:
Verification of the processor: past
memory test: past
drive hard smart check: past
hard drive short DST: failure
Failure ID: GU2AKQ - 6N26P4-QFPJW1-60XM03
Product ID: C6N75UA #ABA
Hard drive 1
For more information, go here.
I can't find it.
Help.
Thank you!
Hello
The short drive Self Test (DST) failure error code would indicate that hard is defective and must be replaced.
If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.
If you live in the United States, contact HP here.
If you are in another part of the world, begin here.
If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.
Kind regards
DP - K
-
Using my Vista 64-bit dvd recovery tools section I ran the test of memory. When the computer reboots, it went through the test, but at the end it starts just the test everywhere after the third time I restarted the pc, he went to the same point and started again the memory test, I checked the settings and the memory test is configured to only run two times but he wears only whenever he finnishes it again. Can someone tell me how to stop it?
Hello
Have you successfully completed the diagnostic test memory over WinRE (Windows Recovery Environment)?
What was the result of the analysis?
Start the scan memory as an administrator.
1. click on start, type memory diagnostics tool in the search for text box, right-click on it and click Run as administrator.
If you are prompted for an administrator password or for confirmation, type the password, or click on continue.
2. click on restart now and check for problems or check the problems the next time I start my computer.
Understand the results of the Diagnostic tool memory:
If memory diagnostics tool ends the first pass and no error, your RAM is working no doubt. You can still run the diagnostic tool memory several times using the same settings to ensure that the Diagnostic tool memory cannot find any errors with your RAM. If you want to test your RAM more completely, you can run the test suite expanded by pressing T during the Memory Diagnostic tool is running. You should run for several hours and then Memory Diagnostic tool. Also, if you change the sequence of tests or one of the parameters of the Memory Diagnostic tool, the current test pass restarts.
If the Memory Diagnostics tool detects errors that occur in your RAM, the screen is updated with information about the error. A "Fail" result for a test indicates this particular test has detected an error. If a test fails, your computer has for lack of material.
If the memory diagnostics tool detects errors in your hardware, you must correct the errors and rerun the Diagnostic tool memory until no errors are reported. Then, you try to run Windows again. If you do not, it may be that Windows does not work properly.
You can try to identify individuals without component of memory. However, if errors are found and that your computer is under warranty, we recommend that you contact the manufacturer for troubleshooting.
Memory diagnostic tool information: http://windows.microsoft.com/en-us/windows-vista/How-do-I-know-if-my-computer-has-a-memory-problem
I hope this helps.
Kind regards
Syed V
Answers from Microsoft supports the engineer.
Maybe you are looking for
-
How to replace the battery CMOS on TECRA M3?
Could someone tell this newbie how to change the battery CMOS on a Tecra M3?I can see it is located under the hard drive that I can remove, but cannot see how to strip all along to get to the battery. Thank you very much nilocp
-
The list of sources available DAQmx triggers
If you set a task of acquiring, OR max on the "Triggering" tab, if you select "Digital Edge" in 'Type of trigger' on the right a new control will appear and allow you to choose from a list of choices like "/ PFI1/Dev1. How can you get a list of these
-
Is it safe to keep a photocopy of his passport on Skydrive?
I heard that if you lose your Passport on holiday for example, if you have a copy somewhere, it is acceptable for the time.
-
Good... man this is frustrating... So, I installed Sims 1. I'll install the expansion packs. They say something like that... «you have already installed version 1.2...» abandonment of installation. I uninstalled the files and delete them before you r
-
How can I download from a website to a cd?