Methods of protection for NI USB-6009

Similar Questions

• What is the MTBF for the USB-6009 case

  What is the average time between failures (MTBF) for the USB-6009 case?

  Hello

  Unfortunately, there is no available for the USB-6009 case MTBF.  In order to retrieve this information, there is a cost for our R & D department.  If you need this number, please contact your local representative OR or open a service request to ni.com/ask.

  I apologize for the inconvenience.

• Why is the selection of the mode disabled in max for NIDAQ-USB-6009?

  I try to use NOR-USB-6009 AO to generate the sinusoidal signal.

  (1) I want to use MAX, but the selection of the mode and frequency are all disabled in the "Analog output" section

  (2) I find a VB example to generate the sine wave, but I received an error message.

  I want to know if the OR-6009 function support limited or not...?

  The attachment includes the screenshot.

  Thank you very much!

  Kevin

  Kevin,

  Yes. Timed software means that the appliance has no internal clock or the buffer. You call the AO write with data point. Then you call AO write later with another data point. Repeat until cooked. This means that the maximum rate of update of the AO is approximately 100 hertz or a little faster. It also means that there is a lot of jitter of synchronization due to latencies of the OS at speeds like that.

  Think about AO on the USB-6009 case as a parameter Variant sometimes of continuous tension for your system.

  Lynn

• Proposal to expand the scope of an analog pathway for a USB-6009 or similar device

  I'm sure that someone thought to how reduce an analog input voltage to an acceptable range for the data acquisition device that they use. I'd be interested to see what has already been written on the subject. In the meantime, I enclose an exel sheet spread detailing my own approach to this situation.

  1 SCXI chassis of NOR

  2 OPTO20

  3. Non-inverting op-amp circuit.

  Signal conditioning circuit is now quite cheap and reliable.  For me, it is better to buy something off the shelf, because in the future it will be easy for people to follow my design as well.

  Yik

• measurement of current with usb-6009

  Hi, my name is hung and I am a student in electrical engineering... I'm doing a thesis that the project using Labview and acquisition of data NOR UBS-6009 to simulate the function generator, Oscilloscope, Digital Microsoft (DMM)... and now I'm simulating DMM. I managed to measure the voltage and resistance which i use voltage divider method, but I encountered a problem with the current measurement. The problem is the USB-6009 to measure use the current, it measures an incorrect value. I tried to use the current CQI 0-20mA Sample.vi example but it always measures an incorrect value. If NI USB-6009 supports for the measuring current? Is there a way to measure the currents using USB-6009? Please, help me. This thesis project is so important for me. Thank you.

  Hung,

  Since you are a student in electrical engineering, I'll show you how to know the answers to your questions.

  1. review the specifications for the USB-6009 case.  In particular look at the specifications of analog input.

  2. How would you measure current if you had only a voltmeter?  Use the same method with the USB-6009 case.  (Tip: apply the Ohm's law).

  General comment: when using any measuring instrument, always consider maximum permitted values at the entrances so that the instrument is not damaged

  and the measure is accurate.

  Let us know how you do.

  Lynn

• BSOD when base closing program NI DAQ USB-6009

  So, as the title suggests, I get the BSOD error code: MULTIPLE_IRP_COMPLETE_REQUESTS when I close the basic example of the analog input for NI USB-6009. Someone at - he lived this before? My specs are:

  -LV version 15.0 32 bits (developing 64-bit installation to solve a problem without a report, do not know if this will help here as well)

  -Win7 Ultimate x 64 (SP1)

  -Alienware M17x R3

  -Core i7-2860QM

  -12 GB OF DDR3 RAM

  Any ideas on what could be the cause?

  Does happen with particular vi or exe or anyone, including max and daq assistant? If it was built on this machine? Try to force recompile all (Ctrl + Shift + click the button run.

  I can hardly imagine what can be encoded in simple artificial intelligence causes of BSOD. I'd say it's machine problem. Something is not installed correctly. Is - this change help USB? Card mother does a USB 2.0?

• How to measure the digital output of the linear actuator on USB-6009?

  Hello

  I am a new user of Labview and need help to measure a digital input signal.

  I have an actuator Bimba Original line electric with a motor continuous integrated with encoder, drive and the controller. The drive has a programmable digital output that I put as a tachometer output that emits pulses of square wave 100 per turn of the engine. I put the engine to make a total of 56 rev in 22 dry. I want to measure the speed of motor rotation labview real-time and synchronize it with a few other analog input signals. I wired the actuator for the USB-6009 case as shown below.

  

  I opened the test i/o digital USB-6009 Panel and fix all the lines of port 0 as inputs. However, when I click on start and run the actuator, p0.0 led flashes, as indicated below.

  

  Shouldn't the led blink in response to revolutions of engines?

  I want basically to collect the drive pulse signals and convert them in rpm on labview.

  ahsan2 wrote:

  I have it wired correctly?

  It would help if you do not attach the HIGH signal.  Remove the + 5V in the circuit.

• PID control using USB-6009, need of simple video or example vi

  I have a new usb-6009 and have tried all the videos on the NC

  Web site for practice. However with the version 8.6.1 I can't use

  the pid simple vi which is used on the video. (its too old 5 x v)

  I just need a PID simple vi to 8.6.1.so that day, I saw many complexes of vi

  for the demo of pid... I'm creating control tools... too to choose...

  any help looking for a simple vi or video? - as the demo shown

  the NI USB-6009 Web site...

  Concerning

  JJ

  Well, I did a simple proportional control for box usb-6009

  with a time inside the while loop... don't know if it's the

  Gourmet addresses... my sub PID vi is very simple...

  But it shows how to use labview and usb-6009 for case

  a loop very simple return PID...

  Concerning

  J

• Simulate signals wired to the DAQ assistant for USB-6009 device

  Hello

  I'm trying to send a signal to the DAQ Assistant Express VI.  I watched the movie "Generating a Signal" on the Web site of NOR (www.ni.com/academic/students/learnlabview/generate.htm) and I have my Signal simulate connected directly on the DAQ Assistant, as shown in this film.  In my case, the DAQ Assistant sends the signal to a device USB-6009.

  However, I received this message:

  Error-200077 occurred to the DAQ Assistant
  Possible reasons:

  Requested value is not supported for this property value. The value of the property may be invalid because it is in conflict with another property.

  Property: SampTimingType
  asked the value: Sample clock
  You select: On-demand

  If I select 'On Demand' in my DAQ assistant and run the vi everything works beautifully.  However, I need my DAQ assistant to be configured to generate a waveform AC continuous, not output a single alternating current rippling.

  What happens here?  I did not have this problem before on other devices of NOR. I am using LABView 2010.

  Please answer.

  Thank you.

  double post

• Recommend components for the plant of thumbnails that will be automated using NI USB-6009

  I build a treatment for a University project and I'm looking for a few recommendations of components that work well with the NI USB-6009 case. Because of what is a project of the University, my budget is $ 100 and I need the following:

  a float switch or something similar

  a solenoid valve two-way or three-way

  a pump

  a pH sensor

  a temperature sensor

  a camera

  I understand that I may not have a sufficient budget for all these components, but all product recommendations would be appreciated.

  Hello

  I recommend using the following tool to see examples of projects other users worked on in order to determine the appropriate components: http://www.ni.com/examples/

  I hope this helps!

• Oscilloscope for the acquisition of data from the usb-6009 or - example of temporal division for 5 seconds, 10 seconds

  Hey Hey everyone

  I was looking for an example for two-channel oscilloscope virtual using e/s all-in-one of the 14 bits of NI DAQ USB 6009. I tried to research for example BOF time division or s/div for 1 second, 5 seconds, 10 seconds.  but was shocked to find that there is no reference for it. The range of oscilloscoper virtual

  Minimum - 10 micro s / div maximum -10milli second div but there is no example for 1 second / div or 5 seconds / div...  If anyone can guide me. I'm new to labview environment.

  This is the oscilloscope two sample obtained from google search. is there material limitations. ?

  I'm working on continuous 4-channel data acquisition data acquisition using niusb 6009

  The sampling frequency is sufficient for any desired s/div. The sample rate is 12 ksamples / s per channel, so if that meets the Nyquist criteria for the input signal, you can capture it. The number of samples has no effect on that with the exception of the amount of the signal you acquire. Your chart is not stable, if you do not trigger the acquisition. Even as real significance, therefore your emulation seems actually successful.

• Device driver in Linux and ready to compile application user for USB-6009

  Hello

  I intend to use the acquisition card to USB-6009 data under Linux platform. To do this, I need driver linux for acquisition card data USB-6009 and some read-compilation-and-program to use "user application" which can take samples of the card, to implement some buffering or write to the file. It would be beneficial if I could also get sample code to generate a sinusoidal low frequency signal, using the D-to-A converter available on the Board of Directors.

  Also I need installation instructions for the NOR-DAQ software under standard linux environment.

  Thank you for your quick and detailed response,

  Adeel Malik,

  Research engineer,

  Institute of telecommunications research,

  Mawson Lakes Boulevard,

  Mawson Lakes,

  South Australia, 5095,.

  Australia

  Mobile: + 61 0404 030 071

  E-mail: [email protected]

  Hello Adeel,

  You will need to install the libstdc ++. so.5 Library.  A Google search has a few useful discussions that give more information on the procedure to follow if you are not sure:

  • FC4 is not libstdc ++. so.5
  • libstdc ++. found so.5

  Let me know if you have installation problems - you can also try to contact redhat support if you are having problems.  If you have problems, please post so we can document the troubleshooting procedure to help all customers who may experience this problem in the future.  Thanks for posting!

  -John

• Sampling frequency for two different routes for acquisition of data USB-6009

  Hello

  I use a box USB-6009 and incorporating the "daq assistant" to change the sampling frequency.  I'm trying to find a way to set the sampling frequency to two unique values for the two separate channels.  I tried implementing two assistants daq and different for each channel sampling frequency setting, although it does not work.  Is it possible to set the sampling frequency for all channels, and then reduce the rate for another channel - or an alternative?  I would be recognizing any input on this matter, thank you!

  -Anthony

  All tasks on a DAQ card using the sample clock should use the same clock.  Therefore, you cannot have two tasks on the same sample of DAQ card at different rates.

  Alternatives would be:

  1. to combine all channels in a single task and to accept additional data

  2 get an additional DAQ card to use at the same time

• Typical values for the external resistance of pull-up on a line of output digital NI USB 6009?

  Hi all

  I use a digital line on a USB-6009 to control a SSR by the attached diagram (in the manual USB 6009).  I don't have access to a variable resistor or box of 10 years, so I'm hoping to get a good approximate estimate for the value of Re.  When I connect the CRDD at a 5V supply, it shoots 8.2mADC when closed.

  Any suggestions?  Is there any other information I can post for help with the guestimations?

  Thank you!

  I have found an old box of decade Heathkit and understand the degree of correct resistance 100 ohms.

• Ideas for driver control of motors stepper with USB-6009

  I have a stepper motor driver that supports a digital input for the control signal.  Each rising edge on the driver entry corresponds to the movement of a single step.  I have two devices USB-6009.  Is it possible to generate a digital signal with the 6009 faster than 150 Hz?  I need produce variable frequency in the interval from 0 to 1 KHz.

  zaphead,

  The OID on your 6009 being timed sofware it comes out as fast as your computer all supports.  If a computer faster or less current will help things but you will get not the 1 kHz you need.  The best way to get this is to use another card that supports hardware timing DIO.