mg7720 wireless network name change

How can I change the name of the printer wireless?

Advertisement

Hi Rjw1952,

To connect your PIXMA MG7720 to your wireless network, please follow these steps:

1. press the button on your MG7720 PIXMA HOME.

2. slide the screen, and then select LAN settings.

3. tap on settings WLAN.

4. click on installation Standard.

5. a list of detected access points appears.  Select your wireless network.

6. Enter your wireless network password, and then click OK.

Your PIXMA MG7720 will now be connected to your network.

If you continue to have difficulties, please contact our support group by using the following link:

http://www.USA.Canon.com/Cusa/consumer/standard_display/contact_us_consumer

Tags: Canon Printer

Similar Questions

  • Name of the mn500 base station wireless network (be) changed to MSHOME.

    Run a wireless network with the mn500 smooth base station for years.   Last Saturday the network name is MSHOME.  Any thoughts on what is happening or how to change back the name I assigned it?

    Sorry, I misunderstood.  You are referring to the name wireless ID SSID (Service Set).  It is defined in the configuration of your wireless router.  I'm not familiar with this particular router, but with most routers, you can use a web browser to connect to the router (your model, it is http://192.168.2.1) preference of a wired connection that to change the SSID will cause a disconnect wireless, connect you with password "admin" (unless it's been changed) and change the settings.  On most routers, hold the button Reset on the router will return to factory settings which is possible as to how this change could occur.  Links to the user guide and manual configuration is on this page:

    "The Microsoft Home Networking product documentation"
      <>http://support.Microsoft.com/kb/902461 >

    HTH,
    JW

  • Printer wireless network name recognition

    I have an all-in-One of C4795 printer, on Vista 64-bit, which can not connect again ATT Uverse router. The router has been replaced and printer identifies the old network name/number. I tried everything the HP web site offers, but nothing worksI. At some point in the implementation I find the new name/number and I printed the report of NetworkTest wireless and it shows the old name/number. Help! Joe C.

    Hi Joey1969,

    Follow these steps in the document below. Let me know if you need help.

    http://goo.GL/jXYCw

  • Help: wireless network settings changed on the router but loss of hp install cd for pro8000 wireless

    HP Officejet Pro 8000 A809 Wireless

    Mac OS 10.6 and 10.7

    I changed my router wireless network settings and now I need to change on my printer so it can join the network.

    Problem is that I throw my installation CD and it seems that you need to change the settings?

    I connected via USB and downloaded the driver on the net and reinstalled but don't see an option or a chance to set the printer wifi options.

    I tried to reset the printer settings wifi with three taps of the paper button while now thought wireless button I'd see change options only when usb connected, but I did not.

    It seems weird and archiac you would need the physical disk to make the required changes.

    Any help would be appreciated.

    Hello

    Temporary connect the USB printer to a Mac.

    Applications > Hewlett-Packard > utility device, run the installation wizard.

    Select the printer and then follow the on-screen instructions to configure the wireless connection.

    Please let me know of any questions,

    Shlomi

  • Change network name

    When I change the name of the network should I reconfigure all printers on the network?

    Potentially, Yes. If your printers are wireless, then you will need to reconfigure with new wireless network name to connect.

  • HP Photosmart C4780 connects not (wireless) on Mac or wireless network

    Sorry for the long post, but please someone help me!

    I bought my new printer a few days (actually 14th) and began to implement on my MacBook Pro with my Wi - Fi, which is routed through a Linksys router and mainly through my desktop computer (a PC with Windows XP). I used the CD that came with the printer to set it up on my Mac and it has set up the fine by USB, but when I try to set up the wireless, I get the following message:

    "Device not connected: to configure the network settings for the selected device, please connect via USB temporarily." The device can be disconnected from the USB once the network settings are transferred. »

    I reconnected and got the same message over and over again, so I decided to set up on my desktop computer instead. This does not work either and I got the same message on my desk I have on my laptop. Uninstalled on both computers, reinstalled and I STILL got the same message. At this point, I'm about to throw all the electronics in my bath tub and be done with them but on the contrary, I checked (and double checked - and triple checked) my router via my browser settings, fact that I know the SSID and the password and reconnected to the network through my laptop... Once again, the same message. I tried the network installation of push, the installation of the network PIN, I feel I have tried everything! Probably miss me something small, but eyes fresh is always an asset.

    Can someone help me? I printed a Test report of the network so that a Page Network Configuration and settings I received both... if need be, I can post the information from my router, in order to verify to implement, but after two days of trying to implement something that should have taken ten minutes (sometimes) I'm at my wits end.

    Network Test report:

    "Your HP printer cannot find your wireless router. Check our wireless router has power. Make sure that your network (SSID) HP printer name exactly matches your router (SSID) wireless network name. If they do not exactly match, run the installation of the wireless network to set up your HP printer. »

    How to change the network name of the printer to match?

    Summary of diagnosis:

    Wireless on: PASS

    Wireless work: PASS

    Find the network name (SSID): FAILURE

    Security: PASS

    The printer settings compatible with the wireless router settings: does not work

    No filtering: does not work

    Related: Does not work

    Signal strength: does not work

    Other networks detected matching your network name (SSID): does not work

    Detected wireless networks: 1

    Downlink Count: 0

    Channel: Does not work

    Although I was given my SSID (which does not match my home network - but how can I change this?) and my MAC address (I guess for the printer), so I didn't have the IP address of my printer has no way for me to get online to check all the settings! Is there another way to get this IP address?

    Summary of configuration:

    Communication mode: Infrastructure

    Authentication type: open

    Encryption: no

    ______________________________________________________________

    Network Setup page:

    General information:

    Network status: offline

    Type of connection: no

    URL to Web server integrated: http://0.0.0.0

    Firmware Version/Hostname/serial number were all given

    Admin password: not set

    802.11 wireless

    Hardware address (MAC): data

    Status: disconnected

    Port 9100

    Status: enabled

    mDNS

    Status: enabled

    Service name: Photosmart C4700 Series [6 last digits of my MAC address]

    SLP

    Status: enabled

    Microsoft Web Services

    WS discovery

    Status: enabled

    WS Print

    Status: enabled

    PC connected (s)

    Address IP/hostname: (nothing is here) Time since last access (mm: SS): (nothing is here)      

    Number of 802.11 networks discovered: 1

    (my correct information of wireless network is here, including the SSID, Mode (Infrastructure), BSSID, Channel, privacy (RSN), Auth (WPA - PSK), Encrypt (TKIP-AES), Signal and WPS (no))

    Help!

    Did you read this on your Verizon FIOS router? : http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/Connection-problems-with-Verizon-FIOS-Actiontec-routers/td-p/892967

  • Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

    I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

    Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...

    Turn on AirPort Extreme for a few minutes... If it is not already turned on

    Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.

    Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status

    Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme

    To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

    Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".

    When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password

  • Win 7 does not recognize that I am connected to my home wireless network.

    Recently, I upgraded my desktop and my laptop at home to Win 7. I'm trying to set up a home network, but on my laptop, I can't change my home network location. Even though my laptop is connected to the internet via my wireless router, Windows don't think that I'm connected to a network. When I click on "connect to a network", it shows that I am connected to my wireless router. When I try to set up a home network on the laptop, it tells me I need to change the network location of the Public at home, but since he did not think that I am connected, it will not allow to do me this.  I searched the internet and worked through it for hours, but can't seem to find a solution to this problem. Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas:

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    I had this same problem.  I have a home group on my desktop running win 7 64 bit.  My laptop (win 7 64 bit) could not connect because the internet connection was showing pubic hair and I couldn't change it.  Here's what I did.  I deleted all my networks and groups off the laptop computer.  I restarted my laptop.  On my desktop, I went into Control Panel, home group and consulted my password.  I also need my wep key of wireless network.

    To better understand, my wireless network name is cleopatraiz

    On my laptop, I went into the wireless network connections through the status bar at the bottom right which displays all networks wireless scope.  I clicked on my wireless (cleopatraiz) and it prompted for the wep key.  I entered that and then I went into newwork & Sharing Center, was now showing my active network as cleopatriz, I clicked on choose home group and sharing options and joined using my password of the Group House of desktop computers.  It worked.

  • Satellite Pro L510 cannot access my wireless network

    The laptop recognizes wireless networks are available but requires a 'logon domain' with my user name and password.
    Where can I find the logon domain? What is it?

    Hi mate

    I don't know how you are trying to connect to the WLAN, but generally you n t need no user to connect to the WLan router password.

    You need, it's the right SSID (wireless network name), Wlan encryption right and good WiFi encryption password.

    First of all, ensuring that the WiFi network has been successfully activated!
    Key combination to select Wlan using FN + F8!
    Also read the manual of use of laptops for more details how to enable the Wlan!

    Then, you must configure the Wlan router every router supports a configuration different procedure but normally you should always have a manual with your router.
    There should be a step by step instruction how configure it!

  • Screen missing on e4620 to enter the SSID of the wireless network

    The SSID of my wireless network has changed and I can't go to the correct screen on my e4620 all-in-one to enter the new SSID.  The network menu Wireless gives me the ability to use WPS that I can't use.  How to input SSID on the printer screen?

    I solved the problem of the printer connected to my computer via a USB cable, and then using the printer setup utility to turn off the PC to a wireless connection.

  • HP LaserJet 200 colorMFP M276nw connects to my wireless network, but will not recognize the printer

    I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?

    Hi @lelg,

    I understand that you want to configure the printer on the wireless network. I can help you with this.

    Uninstall the printer software.

    Uninstalling the printer software.

    Restore the default settings of the printer.

    Go to Configuration, restore the default values.

    Cycle power to the router and the computer.

    Run the installer on the printer wireless.

    Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.

    Print a configuration page to get the IP address of the printer.

    Print a Configuration report.

    Select the method.

    If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)

    If it loads the page from the network printer then the printer is on the network.

    Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.

    Select your operating system, click Next and click on the software to download and install.

    Test the printer.

    What operating system do you use? How to find the Windows Edition and the Version on your computer.

    Please provide detailed results if you're still having problems.

    Good day!
    Thank you.

  • Laptop WiFi problem, «identifying...» (network name) ».

    Hello
    I'm having a problem with the wireless on my laptop. Its a HP Pavilion dv6000 and just under a year of age. I had no problems with the wireless until recently. I use the laptop at home and usually the internet is very well (apart from the occasional disconnection), but when I'm at school do frequently connect to the school network (I am a student of the University, and there are several routers throughout the school and in the many buildings). Sometimes it will connect in one building and I'll switch to another and it does not connect. Each time, he does not connect it always says "identifier...". (wireless network name) ». No amount of repair, restart or reset the network card it won't connect. The strange thing is that sometimes it connects to the router in this building (i.e. library) and sometimes it won't. Whenever I have check the status shows that the laptop is received but does not send do not.

    Help! This problem is really starting to annoy me and I don't want to end up throwing my laptop on the whole of the library.

    Hello

    1st brand one Restore Point so that you can return back if necessary (it shouldn't be though).

    How to create a Vista System Restore Point
    http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
    --------------------------------------------------------------------------

    Actually try updating your driver and disabling the network logon.

    Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
    version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
    Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    Download - SAVE - go where you put it - right click – RUN AS ADMIN.

    You can download several at once however restart after the installation of each of them.

    After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
    manufacturer of system become your backup policies).

    Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
    updated drivers.

    I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
    are almost always old, and you can search drivers manually as needed.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ------------------------------------------------------

    Do another restore Point then you can go back to where you were if necessary with new active pilots.

    Make sure you know the details of connection to your wireless router - SSID and password.

    You lose connection when you do and have to redo your logon.

    I would like to delete ALL networks, so you can restore if necessary.

    Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
    lower left click on merge or delete network locations - REMOVE all instances of your network (and the
    others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

    -----------------------------------------------------

    Check this box:

    Strange problem with Internet under Vista
    http://www.catonett.com/blog/archives/194

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
    http://support.Microsoft.com/kb/928233/en-us

    ----------------------------------------------------

    And:

    Network connection problems
    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    I hope this helps.
    Rob - bicycle - Mark Twain said it is good.

  • How to find my network name?

    original title: Internet

    One of my friends came from China and she brought a laptop with it. When she arrived home, she could not connect to the Internet even if my PC can. When we looked in wireless connections, it did not show the name of our network. I have to ask how I can find it.

    It depends on if the router assigns to hide my SSID or wireless network name.

    You must Access the router interface or GUI and find the wireless settings, and then view the name of the wireless network.

    If you have hidden then you should keep the name of your wireless network, as others prefer to hide the name so no one else will be able to see and connect to.

    You must also consider your WEP or password make sure that you have it.

    you know your IP of the gateway?

    Let's find out who. Press the windows from the keyboard, and then press R in total.

    There type cmd and press ENTER.

    type at the command prompt.

    ipconfig

    Send us the details here or just look for the default gateway and get back to us.

    from there, we will be able to access the router page I hope that the username and password which is always enabled by default, which is the user name: admin password is password or admin.

    * your ISP can help you get the router as well.

    Thank you

    Makoi

  • How can I change the name of my wireless network?

    I use OS X 10.11.4 and utility Airport 6.3.6. I would change the name of my network and I don't know how or where to do this. And once this is done, have what I would do with my extreme and Express to continue them to work?   Any help would be appreciated. Thank you.

    Cheers, Peter

    I use OS X 10.11.4 and utility Airport 6.3.6. I would change the name of my network and I don't know how or where to do this.

    You can change the name of the network using AirPort Utility as follows:

    • Run the AirPort Utility.
    • Select the AirPort base station and then, select change.
    • Select the wireless tab.
    • The network name can be changed in the field "name of the wireless network. Enter the desired name, and select update.
  • change the network name on my wireless router?

    A few months ago, I bought my linksys router and did the installation of all the stuff that day, including changing the name of the default network. I want to change the name to something different, but when I went to the address of the facility, there was no box to put the new network name [I was on standard wireless settings tab in the wireless section]. Help please?

    [Yay that worked, thank you:]

Maybe you are looking for

  • Old keywords still exist

    I deleted a few keyword search bookmarks, but enter the old keywords in the address bar can still provoke respective research.Funny enough, the bar does not show even search by keyword as a suggestion as it does with traditional keyword searches. (li

  • TouchPad Driver installed, but the synaptic ClickPad not found

    I have a problem with my touchpad. I already install the synaptic Touch pad. The touchpad is not more intelligent (can not perform gestures / sensitivity adjustment). When will 'Control Panel' > 'Mouse', the "Synatic Clickpad" tab isn't there. Please

  • Windows Media pLayer error code cood11b1

    Original title: windows media player my windows media player will not be my music player. There is a red x on my music. an error code cood11b1 appears in the error details. This could be the issue of digital rights management?

  • Issue of Windows Vista SP2

    I was wondering if 500 MB package from the microsoft.com Download Center is the same with the 60-70 MB package that Windows Update offers. 500MB vs 70 MB What is the difference?

  • How to split the screen on 2 monitors?

    I have 2 screens (monitors) and to split the info on the main screen so that I / 2 if poster on the 1 screen and the other half appears on the other screen. How is that done?