Michael device

Similar Questions

• MacBook can not find bluetooth devices

  I just bought a new Macbook.  He can not find bluetooth devices.  The device is fully charged and so forth.  He saw the mouse for a fraction of a second, but then he fell.  I tried other bluetooth devices.  It does not find.

  I had this problem too, turn on the Macbook and off is your best bet. But if this does not work, you can go into the settings of your macbook. Settings - Bluetooth - advanced and ensuring that all things have been checked. Hope this helps, good luck to you.

  ~ Michael M

• Ringtone and gamemusic only on the blutooth/headphones-device

  Hi you all out there.

  My iPhone 5 (most recent iOS) is not connected to any external device via bluetooth, etc., no headphones plugged.

  So there is no ring tone for incoming calls (vibrant works), game-apps have no sound. Dictation voice-messages does not work, the curve which shows the recognition of the frequencies is flat. But the music from the music app is normally played on the loudspreaker!

  But when I connect it to a speaker of the blutooth with a microphone, I hear the ringtone and game-music and saving messages of speech also works via the blutooth device. The same thing when the headphones are connected.

  Mode normal iPhone always think, it is connected to another Bluetooth device or something else and it's use for some acoustic out - and input - if it is not connected.

  I rebooted several times, flightmode turned on and off, ignored or deleted all bluetooth devices, he has experienced so far (only 2), opened the only application, which allows to redirect the output to devices outside and clicked on "iPhone" or "speaker" as the device to use - nothing helped so far...

  Any other ideas?

  Thanks in advance!

  Michael

  Look at the switch at the top left of the phone. Make sure you stop sounds. If you see orange in this turnout, reverse the reverse effect.

• I can't find where to enter my access code to my iOS devices

  My Firefox browser on my iPad completely froze and I deleted the application and then reinstalled. Now I can't synchronize as
  !) I can not find anywhere to enter the password on my pc
  (2) I don't have a note of my recovery key
  (3) I don't have the option in the menu to sync on the pc for the "link" of the device.

  Can someone help me to re sync my iOS device please?

  Thank you Michael, if all goes well there will be something soon. In the meantime, I'm going to remove this app - it's a shame, because it worked fine until the last update.

• Tecra S5 need to know the built-in BT device class

  Hello

  I want to know the class of the bluetooth device built into the laptop Toshiba Tecra S5.
  But I wasn't able to find anything in the documentation and I was not able to find the class of the device in the windows Device Manager.

  Does anyone know the class of the bluetooth device, namely the scope of the bluetooth device (categories 1 to 100 m, class 2 up to 10 m, up to 3 m 1)?

  Thanks for help.

  Greetings,
  Michael

  Hello

  Everything I found on the BT made module is a MODULE of BT 2.1 + EDR with INTEGRATED BT's ANTENNA.

  But have you tried one of hardware diagnostics tool Everest Home Edition / Sandra?
  Select this check box.

• HP Pavilion dv8-1099eo: device Base system and unknown device drivers Windows 7 Ultimate lack

  Hello

  Since a new installation of Windows 7 64 bit it is has little material without driver on all simply not recognised. Here is the hardware ID's I hope someone can help get this sort? Laptop computer runs much slower with the CPU it has. An upgrade from 4 GB to 8 GB of RAM is useful?

  1. base system device

  PCI\VEN_197B & DEV_2384 & SUBSYS_7001103C & REV_00
  PCI\VEN_197B & DEV_2384 & SUBSYS_7001103C
  PCI\VEN_197B & DEV_2384 & CC_088000
  PCI\VEN_197B & DEV_2384 & CC_0880

  2 - system base unit

  PCI\VEN_197B & DEV_2382 & SUBSYS_7001103C & REV_00
  PCI\VEN_197B & DEV_2382 & SUBSYS_7001103C
  PCI\VEN_197B & DEV_2382 & CC_088000
  PCI\VEN_197B & DEV_2382 & CC_0880

  3. base system device

  PCI\VEN_197B & DEV_2383 & SUBSYS_7001103C & REV_00
  PCI\VEN_197B & DEV_2383 & SUBSYS_7001103C
  PCI\VEN_197B & DEV_2383 & CC_088000
  PCI\VEN_197B & DEV_2383 & CC_0880

  4 - unknown Device

  ACPI\ENE0100
  * ENE0100

  Thank you

  Michael

  1, 2 & 3 is listed under "Driver-storage" JMicron card reader  ACPI\ENE0100 should be ENE CIR Receiver Driver under "driver-keyboard, mouse and input devices.

  On your page of Support here:

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-DV8-1000-entertainment-notebook-PC-series/4011373/model/4040272#Z7_3054ICK0KGTE30AQO5O3KA30R1

• Implementation of two R7000 mode bridge (1 connects them 2 the internet and all devices, use 2!)

  Hello

  I have trouble finding my drives NAS via Wifi.

  Since I moved my NAS drives to the location of my second router and connect the first router to the internet and all my mobile devices and laptops, I have problems connecting to my NAS readers. Sometimes it works, but more often, it's not.

  I've implemented the first router as "router mode" and the second router als 'bridge'

  Can I change the configuration, so that my second router is connected to the NAS drives and also works as my router for mobile devices and laptops? Then the first router just to connect to the internet and transfer it via the bridge on the second router.

  I tried this, but it doesn't seem to work...

  Concerning

  Michael

  Just to close this topic: got the solution works by using a set of powerline Netgear. It provides internet access to my router located posting the TV and works perfectly. Wireless AC is not the answer to everything, I realize ;-)

  Thanks for the discussion.

• Equium M50 - how to connect firewire devices?

  Equium M50 Intel Celeron M 360 1.4 GHz processor

  Referring to the above, I am able to download photos from my camera to my hard drive, but to download videos that I need to connect a firewire camcorder to the computer. There is no connector on the computer to take in this regard.

  Is there a solution to this?

  Hello

  I put t know if your camera has a firewire port, but if yes it is listed in the Device Manager as IEEE 1394 bus host controller.

  If your device doesn't have a firewire port, you can buy the PCMCIA card with firewire port. By the way: M50 has 4 USB ports (two in the back near LAN port and two near the DVD drive on the right). On models with firewire ports it is definitively placed near S-video output port as Michael described.

  Good bye

• Not recognized USB-6251 (detected) to the MAX but is detected by the Windows 7 Device Manager

  Does anyone have a solution to our problem?

  USB-6251 is not recognized (detected) in MAX but is detected by the Windows 7 Device Manager.

  Is our configuration: Windows 7 (64-BIT), DAXmx 9.3.0f2, MAX 4,8 and USB-6251 (S/N 12B647A. P/N 194929 D - 04 L)

  We had a 'ready' indication/led the 6251.

  We tried several things... (all do not work)

  1. we have installed DAQmx 9.3 (for Windows 7)

  2. clean MAX Database by the following

  http://digital.NI.com/public.nsf/WebSearch/86256F0E001DA9FF86256FFD005B827C?OpenDocument

  Michael B.

  Yes the 6251 appears as a DAQ hardware.  Device charger OR placed in the auto-start services window.  We have refreshed MAX.

  Success!  I had to manually start the device loader.  Even if the service has been set to autostart, it did not work.  Right-click on the service shows that the beginning was selectable.  Click Start and the service began.  Start to MAX and can now see the device.  Open the front panel.

  How does the monitor devices OR running in the interface of the status bar to the device loader service?

  I don't understand why the service was not working.  Is it a security issue?  I am logged in as administrator.  I'll try once again as a normal user.

• Tab 2 A10 - 70F: Internet access via USB connected 3G / 4G device?

  Hello

  The A10 - 70F Tab2 has WiFi only. Is it possible to connect to the internet with a connected USB 3G / 4G? With other words: the tab can handle? Anyone with experience?

  Thank you in advance,

  Michael

  Yes is the short answer. And a few ways to do this:

  1 micro USB Dongle of 3 / 4 g

  2. micro USB to USB 'female' - then plug a 3 / 4 g USB Dongle

  And a couple of less obvious ways:

  1 WiFi connection to another mobile and use of mobile data of quotas (although plans only works on some data)

  2 micro USB to Micro USB and connect a mobile as shown above (does not work on all devices, although I look at the phone and tablet to fight for the battery juice is hilarious)

  3. connected to a PC via the cable USB/WiFi connection internet PC use.

  But yes, 3 / 4g Dongles work indeed & the Tablet seems to walk along very well with a micro USB version or a USB version with an adapter cable.

• The actual voltage of a physical channel of a DAQmx device display

  Hello!

  Quick question: is there a way to read the voltage of a physical channel of a DAQmx device, when there is no task that is running? I want this information after that I ran several tasks. It is important to know the real tension before you start the new task. Any ideas? Thank you!

  Best regards

  Michael

  Hello Michael,

  You are right.

  The 'PCI-6110"and the «PCI-6711" have no internal channels.»

  Could you please describe your exercise.

  Why do you want to know your output voltage before you start a new task.

  Best regards

  Phanuel

• Acer aspire s7-392-9439: lack of default boot device or startup failed.

  Hello
  I bought an Acer aspire s7-392-9439 3 months ago. It has been working fine, until yesterday.
  I turn on the computer and it poped a blue screen with the error: 'lack of default boot device or startup failed'.
  This error reminded me that a message on a bios updated poped over a few days and I have the chance to install it.

  I contacted acer support, I was told that the update of the bios would have avoided this problem. Also, they told me to try things that can help, but unfortunately none of them has:
  1 restore the default bios settings.
  2. change the bios settings: uefi to legacy.
  3 type the Windows key + c when the computer starts.

  When these options do not have they said it is probably a hardware problem and I should send my computer to their repair center.
  My questions are:
  1. If they updated bios would have prevented the problem, how can it be a hardware problem?
  2 - does anyone know how to solve the problem?

  I would appreciate your help,
  Michael

  I had the same problem.  Tried the diskette of starting BACK and did not work.

  Here's how I solved it:

  (apologies to memory are some terms is not on-site)

  1. download the Setup file of the BIOS - link provided above in this thread (isST2212.exe)

  2. on a Windows 8 machine that works - search for 'Create a recovery disk' and run on a USB drive

  3. copy the file #1 to the USB drive once it's done make a recovery disk

  4. in the Acer BIOS (press F2 during startup), change to the method of priming of the legacy

  5 save and exit

  6. turn in the BIOS and move the option USB HDD as first boot device

  7. Save and exit

  8. you will end up in a Windows 8 recovery console

  9. go to Advanced Options - find the option that leads you to the command prompt

  10. from there I went to d: drive and found my file isST2212.exe - run by typing the file name when you are in the folder

  Make sure that you are connected to power - let it run.  It should install, automatic restart and you should be in business.

  I had an Acer offer to fix it for free with a 7-10 day turn around and at the risk of losing all my data.  It's a much better solution!

• Aspire 5745 audio worked. Now, it is not the case. Can not find the audio device. Help

  I lost my audio.  If I look in the Device Manager, it doesn't even have and the entrance to the sound and video controllers.  I need to know how to restore the audio device, then what that drivers to use.  Thanks in advance.

  Michael

  Bluetooth worked.  Now I'm back in business and everything is good,

  Thanks for your help.

• Win XP Pro sp3 does not recognize USB devices.

  I get the message "(défaillant ou inconnu)." "Install driver or driver not required" (!) Can't uninstall/reinstall driver in Device Manager. What should I do my Canon 40 d DSLR recognized? The camera is perfectly functional.
  UPDATE! I used a different USB cable and the problem disappeared. That would be the life that were easy!

  Hi Michael,

  As you mentioned, the problem disappeared using another USB cable, it means that the USB cable has gone wrong.

  You can continue to use another USB cable to connect the Canon 40 d SLR digital.

  Hope the helps of information.
  Please post back and we do know.

• Device Manager: nothing is pulling upwards

  original title: Device Manager

  Recently, I ran a windows update and leave my computer turned off.  When you turn it on, the were (are) of the internet and the printer does not.  I went into Device Manager via Control Panel to see if I could turn them on and there is nothing pulling up in the Device Manager.  All documents and are accessible, but I can't even start a new internet connection and cannot print.   I am currently using another computer (more modern) in another room.  I even tried the SafeMode (f8 in the middle) from the model and go to Device Manager and nothing was there.  I just tried to go through the f8 option and beginning to a previous state that worked and I have the same result...  Everything is saved on that on a 350g portable hard drive.  It would just be easier to wipe the hard drive and start over? If so how would I do this reformatting?  Thanks for any advice.

  Michael

  See if this article helps you:

  "No element appear in the device list manager when you open.
    <>http://support.Microsoft.com/kb/311504 >

  HTH,
  JW